Honda Accord all lights on ABS Traction ECW failed 38-11 38-11 abs solenoid valve malfunction FIXED
HTML-код
- Опубликовано: 28 авг 2024
- Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#38-11 #3811 #honda #accord #tractionlight #abslight #38-11abssolenoidvalvemalfunction #abssolenoid #malfunction #hondaalllightson #hondaecwfailed #ecw #failed #2013accord38-11 #2014accord38-11 #2015accord3811 #2016accord38-11 #2017accord38-11 #2018accord38-11 #2019accord38-11 #2020accord38-11 #2021accord38-11 #2022accord38-11 #2023accord38-11 #abssolenoid #absmalfuction
Video was amazingly helpful. I saved a ton of money by removing my module and sending it for rebuild with Module Master. I love all your Honda videos!
Nice good job glad video helped u and saved u money
What's the part's ,? name I have the same issue in my 2013 honda p
@@elgafe1236 and moduel
Ucambiaste. cuando cambias lo q le cambiastes.no se pulga
Where I can go to access module master ?
I just came back here to say thank you. I took out the module and soldered those broken wires and all lights are gone now. You saved me a lot of money. Thanks again!
Nice!!! Good job!! Appreciate your comment very much!!!
@@RBTheMechaniciiiiio
Did you fix the module by yourself, or did you send it to Module Master or a similar service for modification/fix?
are those wires normally not soldered inside the unit?
@@CivicSiPoland I fixed it myself
I just so happened to do a random Google search about this issue, and I remember your first video, and I'm so glad you solved it! Shout out to you, RB! You're the real MVP!
(Side note: This EXACT error happened literally one month after Honda Care expired on my 2013 Accord EX that I was paying a note on.)
One of my good friends is my dedicated mechanic and he works for Honda in the NYC area. Between me, his customers at work, the people on your thread, Honda forums, and 1/2 of the internet, too many people have this expensive and potentially deadly problem.
Honda should DEFINITELY issue a recall.
Yuppp they defiantly should and on the oil consumption
Having the same issue with my son’s 2013 Honda Accord. The dealership quoted $2,600 to fix it. Ouch. I checked for recalls, but none issued yet. However, lots of complaints filed. I would encourage anyone having this issue to file a complaint with the National Highway Traffic Safety Administration (NHTSA). It’s the only way Honda will take responsibility for it.
Not only this is expencive repair but imagine ur car out of control 80MPH and the contacts internally move and boom no control over car this is dangerous for driver and other on the road
I had this exact scenario happen to me recently on a 2011 Honda Accord V6 at about 75 mph ! The car lost all steering and the brakes were gone. The car spun wildly across both lanes. God was looking out for me as the car ended up in some soft sand on the side of the road. The only damage was some plastic on the front bumper from the impact of short and thin width mile marker sign. The Arizona Highway Patrol and local county Sheriff were dispatched. They were amazed that the car was not damaged. I no longer trust driving the car so it will have to be sent off to Honda dealership soon. @@RBTheMechanic
having same issue with my honda accord coupe 2012 this video helps alot
@@benjiesilva6395 2013 is diffrent. Did u scan for codes
@@RBTheMechanic yes its say vsa module malfunction so im looking for this module until now
Sent my module out to California and recieved it back, after install and clearing codes with scanner all lights are gone. Only getting check charge system notification that I was getting before.!!!! Thanks for this video!!
Ice glad u fixed this issue!! Check charging is related to alternator so check voltage check horn fuse also and see if horn works also disconnect and connect back battery sensor some times it’s loose
@RBTheMechanic I changed the battery, horn works but do have some interior lights off in the center console cigarette lighter and light for park thru drive shifts aren't working.
@@garthmorris6740 check fuses for that anything could be possable with that check charging I had cars with bad horn fuse cause check charging
Charge light coming from the lil box on the negative battery terminal
I did mine today on my 2012 honda accord coupe exl 3.5, and I put the top 2 screws in and the bottom left, but couldn't get the bottom right one in, I couldn't get enough room to get it started but I tightened the three really good and everything seems to work great Thanks for your video sir!!!!
I e
I had a similar issue,after checking the car, we ended up finding out that the issue is the brake fluid that needed to be changed( it was dirty). Thanks for the video
Oh ok
Hello, did you have the exact same issue as shown in the video, including, break failure and traction?
I tried changing the brake oil and still getting the lights on. However, they disappear once I run the car for at least 5 mins. Although sometimes, after disappearing the only one ON is the 🚘 Traction OFF one. Any suggestions???
did the issue ever come back? did your issue say FCM failure or did you have a different message?
I have the same issue with my 2014 accord after watching this I feel confident doing it my self. Thank you for uploading this video your the best🙏👍
Yup there’s guy on eBay who can repair ur and moduel send him old one and he will fix and send back to u
@@RBTheMechanic how much does he charge?
@@emmanuellopez1028 I’m not sure I think it’s 250
@RB THE MECHANIC do you have thr part # ?
Great video! I had the same issues with my 13 accord LX-S coupe. Rather than buying a new or used module off eBay, I decided to tear into the module and repair it myself. It took some research, trial and some error but it’s fixed. Commonly, it seems, the electro-welded connections inside the module with very thin, very soft wires come disconnected from vibration. I had no wiring diagram but tested continuity to find the broken connection. Soldered new wire on and good to go!
Niceee I need more information u have some pictures? I still have the old moduel I will check it out it makes sense how light came on and off maybe contact bounced around from vibration
I do have pics. Before and after, but I went overboard and soldered new wires on all connections.
@@alanlauver9705 email me I’ll see and then inspect my moduel laying around thecarmechanic201@gmail.com
Hey i’m having the same problem with my 2013 Honda accord. I’ve changed everything I’ve changed the map filter I change the air air sensor filter. I change on a spark plug coil packs in the lights. Keep popping I don’t really have much problem but then that light pops on the ABS light end I lose power but if I shut my car off and turn it back on, it’s gone
@@fernandooyola6862 Thai car has issue with moduel did u scan for the codes I took the old moduel apart it had broken cables inside I will post this video this week soon as it’s finished editing
Excellent video. My friend has a 2015 acura ilx 2.0 and the dash SAS, ABS, TRACTION CONTROL...loghts up and sometimes go off randomly. I checked the fuses and they are good. I pulled and ABS code 123-11. I feel it is most likely the abs module
Yeah
Thanks for showing me the strat. This is what has to be wrong with my Accord too.
Try disconnecting the battery and wait 15 minutes. Will work. Worked for me.
Ur just resetting it
Used your video as a reference for my 2014 Accord. Thanks!
Excellent!
Did you send out or do it yourself? Going through this right now appreciate your info!!!
Thank you for this helpful video! A+
You're very welcome!
Hey, so interesting video. I gotta ask though, why do it this way? If you already have another VSA modulator, it is pretty easy to remove the old one and pop the new one in. You are splitting the old one in half, splitting the replacement in half, trying to get the pins to all fit back together, risking that the unit isn't sealed up correctly....seems like a lot of work and risk for no reason. It is pretty straightforward to take a flare nut wrench and undo the brake lines, swap the unit out (you already took off the bracket mounting bolts in your method in order to jam the unit sideways) and then tighten down the brake lines again. Just a thought for others who come by and watch the video here
I use to do lot of these on older vehicles before I started RUclips … if u change the whole thing u need to bleed and do big long process I actually recommend the whole thing to customer but he said to change the moduel only which I have no complaint for doing I prefer it this way!!!
@@RBTheMechanic i have same concern. Is it ok to just replace the solenoid part of the VSA modulator instead of replacing the entire unit?
@@bzq3386 which solenoid part ur talking about? I replaced the module which are solenoids
@@RBTheMechanic my bad. Thats what I meant. I mean if its ok to replace half the module instead of the entire unit?
@@bzq3386 yup that’s exactly what I did just take ur time and watch the video carefully before u attempt it should be easy disconnect the battery before beginning
Hey RB,
I have a 2013 Honda Accord under 76K miles. For the past month I have been having the same issue. The ABS, EPS, traction and brake light come on and off. I went to other zone and I got a scan with the code 32-11 for the ABS Solenoid Valve Malfunction. Then 2 days ago, the check charging system notice came on the dashboard. I have someone check my car out for me, and said that my alternator was fine and had a charged, but the battery didn't had any water in it and the volt was low when them had check it. Once he put the water in the battery the volt came back into range. I was quoted $2k just for the module alone from honda.
Now I am noticing that when I am reserve parking in I am hearing a squeaking sound. Plus when I start my car and make a right turn, I am hearing a cracking sound in the front.
I ready some of your comments were you recommend to have it fix? Do you have a contact for the person who makes the repairs. Also are you located near NYC?
PS: Thanks for staying update and replying to the comments! I know you a busy with with work. You replies has help me out. I appreciate you for this! Thanks again and God Bless.
No I don’t have contact but u can swarm them on eBay just type in abs moduel repair it will pop up
I am faced with the exact same problem, I have ordered used ABS Module and change it today but still the same lights on and and when I do reverse parking I hearing cracking sound as well in the front. I really don't know what the hack is going with Honda I will never ever buy Honda again, I am sick of it,
@@mohammadayazi9891 yeah they need to recall this but u can also send ur old one out for repairs on eBay it’s $250 they make solid connections inside this one has hair size thickness wiring that’s what broke
@@RBTheMechanic thanks Bro, I will send it today I hope they will fix it
I have exactly the same problem. They are charging me $3,000 at the Honda dealer for ordering the module. Please tell me the real solution to this problem. I need to turn off those lights. Thank you. Greetings from Puerto Rico 🇵🇷
Hi RB.
Like always, this video is amazing! I’m a subscriber and I watch your videos all the time. You rock! I am having the same issue with my 2011 Honda Pilot. I’m getting a 121-01 code for. A VSA Solenoid Valve Malfunction. I ordered the part for my car and I am going to attempt to fix it. By chance, if I can’t do it myself can I come by your shop and pay you to do it? I live in Queens but I am always in New Jersey visiting my daughter. Thanks again for making these videos. They really are a huge help.
Sure we would have to schedule it time and days I’m usually booked so we will put in time for your car update me how it goes worst come to worst I can do it
I just want to take the time out my day to thank you my brother, your video truly good job of helping me to solve this problem. Thank you so much for everything.❤
You are very welcome!! Glad u got this fixed!!!
@@RBTheMechanic I used your video to guide me. It’s no side installment video available but yours. You use hood details to explain how to do the job .. Save me so much money 👍🏾 thank you again 🙏🏾
@@jamarb195 yup thank u!!
I have this issue on my 2015 civic, I changed the fuse and no luck so tomorrow I’m going to change just the module like you did. 🤞🏽Hope that works and I don’t have to change the whole thing.
Civic is in complicated spot but u can do it
The connector with the white clip had oil inside of it, you think I should just replace the entire part including the pump?
@@robertquiroz630 if it’s brake fluid yes it could be leaking
@@RBTheMechanic I remembered my pops sprayed WD-40 in the connector 2weeks ago thinking that could help so I only changed the module and the lights turn off right away. I only took it for a 10min drive but no lights so 🤞 hope it stays that way. Thanks for all your help!
Want to drop a thank you too! Just did this today with my car! Very helpful video!
Only thing I did struggle with is taking out the bottom right nut on the module, I don’t have a crowbar but even with my hands I couldn’t move enough like you did in the video to create space for the ratchet, could you give some pointers there? Did you remove some other things out of the way?
Just pushed it with some force that all brother
Thanks for video, i could not get the 4 small lines nuts loose, i tried Gearwrench flare nut spanner and sidchrome, and this is the only option for me,
Nooo u don’t need to get any brake lines out only connector and 2 screws that’s holding the box moduel
1:18 also is this part expensive? I think I’m going to do as one viewer suggested & complain to National Highway Traffic. Honda needs to do a recall if it’s something as important as this. Thank you so much!
Yes expencive but u can take out ur old one and send it for repair on eBay they sell service search and moduel repair
Thanks for the detailed video!! We're having the same issue on a 2014 Accord; however, I confirmed that both rear hub bearings are bad. The parts will be in this week to swap. These lights used to come on and off periodically, now constant. I'm wondering if the bad rear hubs have been the culprit all along. I'll follow up when I swap out the rear hubs. Thanks again!
Bad hubs can cause abs codes usully the hubs would make noise anyways do the necessary repair first then reset the lights. Also u can scan to see if u have abs moduel codes
@@RBTheMechanic Thanks!
@@stephenjeronymo6093 What was your update please. Seems I have the same problem with my 2015 Honda Accord LX
Appreciate your video, good tips, it's very encouraging.
Yup
Nice video love to see plp like you never give ip
Thank u
I have this same issue with a 14 accord exl 2.4L w/55k miles. I was wondering if there is any reprogramming that you have to do when swap out the old and replaced ECU? Please advise. BTW, keep up the great work. Many DYI'rs are really appreciated your knowledge and prognosis. Great work!!!! Bravo....
Also, I found a used ABS/VSE assembly for same the price as the repair from ebay. Do you think I should get it and swap out the ECU or just send my old one in for repair? Looking forward to your advice. Many thanks.
No u don’t need to reprogram
Buying used one is taking a chance they all got the same issues and start to occur around 50-80k miles so if the moduel u buy is good it should work out no programing needed I just put this one is and it worked u have to might reset the light and calibrate the tpms from the dash anways. I would go with sending out my old one at least it will be better chance and last u longer
@@RBTheMechanic Thank you for your response and advice. Will send mine in via ebay. You're great!!!!
@@SangNguyen-oh5sp let me know how it turn out!!! And how fast is the service I’m planning on doing more down the road
Would this be a possible issue for Honda civic 18 I am getting the steering light, check charge system, and brake system lights coming on but I took it to the dealer and they checked the battery and it’s goo. What would be a common issue for this?
If ur getting check charging light it’s possability ur alternator is bad
@@RBTheMechanic initially when I was having this issue it was also setting off my ABS light and it would blink for a few seconds before turning off and it hasn’t come back on since. I will have it checked thanks love your videos
Hello RB, the check charge notification came on and also all the lights are on as well. ABS include but my steering wheel is so hard to turn. I have an electrical power steering. 2014 Honda Accord Sport. Any idea what I should do first?
I would first scan abs moduel for codes and let me know what the codes are
Had my module sent for repair. I put it all back together and lights are on. I have some cheap computer scanner that doesn't have a reset function. What can 8 do? Maybe the fix was bad or maybe it was something else
Well disconnect the battery for 20 minutes then do tpms calibration from screen. And go for a sping. See if it dose reset it self try that update me
@@RBTheMechanic drove the car around and the lights just went off..so far so good
Great video I have the same problem I want you to fix it in 2014 accord
Yup u can replace this buy or rebuild it there’s service on ebay they u send them old one and they rebuild the moduel
The best master mechanic awesome 👏
Thank you!!
1:15
"Fuck it" 😂
@RBTheMechanic
I saw an ebay listing that ABS module can be taken off and the car can still be driven as long as that hydrolic pump remains in place. do you think that's a good idea?
Also, I get this FCM failure warning but I don't get any codes. Is there something cheaper I should try it out first?
Yes but only problem is if car skids slips slides there’s no control
@@RBTheMechanic I mean I got all those lights on so I assume even now I would slip and slide. Right?
Hey Brodda! Amazing video!!!
I have a 2014 Honda Accord with the same issues. What is the part number for the module?
Idk the part number u have to search it on eBay or buy new one goes by the year make model
Thanks for the video. And that ABS module is expensive, right?
From junk yard it’s like $200 if u find a good deal u can get one with low mileage for bit more also there’s this service on ebay u send them ur old moduel and they will fix the issue that it got problems with resistors and capacitors that’s all it is u can search them and message them on eBay
@@RBTheMechanic Excellent! Thank you very much. And is the module compatible for all of the 9th generation? I have a '13. I get those lights on my dash. I'm going to check the sensors to each tire first, then I'll go this route. Thank you again!
@@nesone6520 yup it should be same same but when u do purchase it make sure u buy it for the year u have u never know the parts sells know it better but it’s should be 100% same
@@RBTheMechanic there's a company that rebuilds them with lifetime warranty for $225 for Honda called G7 computers, imma give em a try
@@teenice894 I’m gonna take note of that and make a ramp let on shop office so I know where to go when I need somthing done with these
@RB The Mechanic Great video and a wealth of info in the comments here. I searched and couldn't really find the answer to my question; so I am going to ask. I did find the G7 Computers who will rebuild and back it up with a lifetime warranty. My question is and this may be a dumb question, can I remove this module only and drive the car until the part is rebuilt. If the part is presumed failed, I guess I can't see why it would matter.
I do want to look at the fuse first; what should I be looking for to see if it is blown. From your video, it does not look like a typical fuse. So I don't if it will be obvious that it's blown.
If I did go with the replacement route where I found the exact fit for my make/model/year- Is programming from the dealer required?
Yeah u might have to pull out the fuse chip and look at the contacts anyways about driving. I wouldn’t recommend it I’m not sure how it would effect the driving wit moduel off I don’t have idea on that never tried it
@@RBTheMechanic thank you sir. As for the replacement route, is programming required by dealer?
@@buffalolegend nope they already programmed
Hi RB dear, I have been your long time subscriber and follow your videos. I have Honda Accord 2017 Sport Special Edition.
Recently my car’s dash board
showing the following lights :
Brake light
Traction light
Steering Control light
But ,
No ABS light .
Brake light keep going off and coming back when I drive the car , but Traction light and Steering Light stays on all the time.
Interesting, when the tires hit and roll over the Bumps on the road ( Speed Breakers ) the BRAKE light comes on and after driving over the bumps the Brake light turn off .
However, Brake light stays on when I am driving on a highway.
Please advise what could be the issue?
Thank you
Seems like Ans moduel is going bad try scanning abs moduel for codes
What is the name of that part you changed?
Man! I will gladly drive to you for repair service
Why wassup what issue ur having?
The same issue. Those 3 lights are on TPMS, EPS, VSA. I have a 2014 Accord Sport 4 cylinder
@RBTheMechanic Will you repair it sir?
2014 Accord EXL Same issue after having routine/scheduled break pads replaced by the dealer. They act like they have NO idea!
Yeah dealer dosent care I would stick with regular mom and pop shop at least they appreciate u giving them business and they do best for u
By the way have it scanned and let me know what codes r in abs moduel then I can guide u
Thank you! Good idea!! Appreciate your thoughts/feedback! 🤍🤍
@@kellieie827 no problem welcome!!!
2014 accord lx coupe all those lights on all started after hitting huge pothole car has over 200 k mi great car otherwise got 38-11 code my question it can’t be a fuse or the wheel and sensor right and can I take my car to you and how much u charge for storage id order it right there and your adress
Scan the car to see if abs moduel has selnoid code most likely it will have it
I recently had a brake job on my 2014 honda accord exl coupe and have had all dash lights lit up. Im getting codes 81-19 and 81-20. Do you think this is related to a faulty VSA?
What dose ur scan tool define the code as. From my research seems like it need yawrate sensor alignment
@@RBTheMechanic 81-19 Yaw Rate Sensor(inside of modulator control unit) Internal Circuit Malfunction
81-20 Acceleration Sensor(inside of modulator control unit) Internal Circuit Malfunction
@@goranpat prolly bad moduel
Hi RB I have the same 2014 Accord V6 with 85K miles. How much should the timing belt, water pump, and tensioner replacement cost? how many hours is this job? Thank you for your videos very helpful.
Good parts and labor with total kit will run around $1400 job is like 4-6 hours if everything goes smooth. This is price for like original parts after marker maybe $900
You're the Man..... Great one... Thanks a lot... 🙏
You're welcome!
7/20/24 1:18 I have 2013 Honda according to my ABS light came on with the steering light traction light & tire pressure. Code read ABS sensor front driver. Put new sensors on the front. Both driver & passenger side. Put new breaks & rotors too. All lights are still on. You think it’s this ?
Scan the car for abs moduel and it will give u codes
great video , my friend's honda i fixed was bad module i replace whole thing with another used one. codes went away. i wonder why those kind always fail
The capacitors inside goes that’s the issues sun guy service then on eBay u gotta send him old moduel
How do you know if it’s the module or the pump that’s the problem? Thank you for the info so far
Good question the codes in the title are the reason they r inside the moduel so scan the car for codes in abs moduel
@@RBTheMechanic ok thank you!
What is the name of that part you changed?
Abs module
I have a 2016 Accord with the 2.4l engine. The gauges are flickering and it won't crank. I put in a new battery and it still does the same thing. Any suggestions?
With new battery it’s still flickering?
@@RBTheMechanic Yes, the gauges are still flickering with the new battery
Hello! Great vid. How long is the flex head ratchet you was using ?
I’m not able to watch the video at some place low data but if it’s soft handle it’s like 13” lenth
Im having the same issues with my mothers 2015 honda accord, lights on the dash looks like what you're dealing with. If anyone did solder the unit, could you show us how you did it? I was about to go buy a used one but i saw some videos say abs units have to be reprogrammed to that car.... sometimes. That sound is my hair being pulled out. 😂
Well I cannot open the repaired one but I do have one that’s I open and how it broken inside
Great work, i have same issue with my 2012 honda crz. Are there certain modules i can use from the 2011-12 crz's that are also manual or does it have to be the exact same part #'s? Thanks in advance
That’s somthing I can’t say for sure but I would search for same exact year make model also there’s service on ebay that charge about $250 u send them the moduel they repair it for u and send it back u can search them by abs moduel repair
So you said I can remove the module on a v6 without disconnecting the brake lines? Once I send the module out what do I suppose to do with the remaining portion of the module that is attached to the brake lines. Do I have to cover that area ?
U cone need to cover it cover the connectors and just to let u know u can’t drive even though it’s drivable but not good idea
@@RBTheMechanic it's there like some type of caps or something I can buy from the store to put on the brake lines once I remove my abs box ?
2013 Honda accord My power steering light came on the dash that’s the only light on though would this be the same issue also ? can’t turn my steering wheel either
Prolly not I would scan the car for codes in all modules but possability this can be
Does anyone know the part number for the white connector? Or the whole connector assembly ? Mine is broken and I think that could be another reason the lights are coming on for this. The connection maybe is not being properly made. Thanks in advance
Sorry no part number might have to buy from junk yard and then splice solder wiring dealer will self whole harnes very expencive
@@RBTheMechanic noted! thanks for the reply brother.
Put the connector in first,, much easier. Got mine rebuilt in California from eBay for $299.
Ok thank !! Nice how did it work out?
BROOO! I just replaced the one on my daughter’s Accord 2012 and all 3 lights (TCS, ABS, and Break ) are off after driving it like a 1/4 mile.
Nice good job!!
Hello how to fix traction light abs light code 66-13 on 2012 honda crosstour
Any other codes ? But it might be same issue
Fire video I just did mines
Yup I just did recent video on this I cut open the moduel and found broken contacts check that out ruclips.net/video/ncoyKh9kJUU/видео.html
Hey. So I got a 2014 Honda Accord. The ldw, fcw, and traction control lights came on like 6 months ago. Now the abs and break light are on. I’ve replaced the brake, speed sensors, calipers, rotors, new brake fluid. The lights are still on. The 38-11 code was on along with 81-19 and 81-20 which 19 is the yaw rate sensor and 20 is the acceleration sensor. But say they’re in the modulator control unit, internal circuit malfunction. You think the abs module is responsible for all that? Or is the modulator control unit something else?
Ur model is the issue
Hey friend so I did another check on my Honda. I disconnected the vacuum hose from the intake manifold. I poured some seafoam inside and tried to start her up. The first time it didn't start the second time it tried and almost stayed on and the third time it stayed on. I left it running and when I put the hose back on it turned off. Took the hose off and she started back up again. Put my finger over the opening in the manifold where I took the hose off and it turned off again. The whole time that FCW light and the other lights were still on but it was running idle and sounded fine. Didn't sound funny or nothing. Going to drive over to the shop and see what code they come up with boss.
Try cleaning the throttle I have video on that type in accord throttle cleaning rb the mechanic. It will come up
just got my module back...The VSA/ABS/Brake lights are still on...Do I need to do anything to reset them or should they turn off on their own?
Go for a drive it might go away on it’s on also do TPMS calabration
Hey bro do you know if it would be the same with a 2015 acura tlx 2.4 ? I would really appreciate it if you can reply im having the same issues and do you have to program it? Thanks in advance
Prolly is same but scan the car for codes before anything most likely same issue
@@RBTheMechanicthank you bro i scanned it but it said that it was the mass air flow sensor i repleced it but it still the same also my brake pedal is a little hard to start the car I bought a used module from the junkyard do you know if i have to program it or just like you did on the video
Question when u install the new module do u have to program with the computer or no need to program it?
Don’t need to program!
I have a 2013 with TPMS, EPS and TCS lights on. Will that same module fix it even though the ABS light is not on?
First u have to scan with high end scan tool and get the codes for each moduel
RB, big fan of the channel. I have a 2014 Accord sport with the tpms,traction control, and power steering light. I have an 81-19 and 81-20 code. What would you suggest? Thanks
I would to begin reset it disconnect the abs moduel and let it be disconnect for 29 minutes then connect it back
Appreciate the response
What did you end up doing
@calvinvillacres1326 I disconnected the module and waited 15 minutes. Plugged it back in, and all the same lights came back on shortly after. I'm still driving the car with all those lights on. No issues.
I get TPSM, hill start, power steering and vsa lights on my dash with code 81-20 and 133-1. Dealership wants 2K to replace it. Is there any way I can replace this part with used ones? Will it require Honda's HDS system to neutralize steering wheel or something? Or VSA module is plug & play?
Car type: honda civic 2014 LX
Try getting ur old one fixed from eBay search up abs moduel repair. Putting in used one might be bad or will go bad quickely
I got all these lights. When I used my neighbors $50 scanner, There was no codes.
I had that case when I hooked up scan tool all other lights came well it will go away drive it for few
@Rb Hey friend I have a question for you. How much would it cost to purchase an alternator for a 2015 Honda accord ex-L model?
Go original from dealer it’s like $600. Don’t use after marker it wount work out
How’s the car doing. Dealer told me if you do that better watch out when it rains it can lock up if it’s not programed.. not sure if he was just trying to scare me. I sent mine in for a repair through eBay.
If it’s not programmed it wouldn’t be fixed all the lights will be on car has been good been over year
Thank you sir! I sent it through eBay and they fixed my old one and sent it back and the lights are completed GONE! It’s been two weeks.
Save myself a couple of 1000 dollars.
Same issue. My question is. Do we have to take to dealer to program a repaired module?
No not if u buy used one or send out ur old one to have it repaired
Hey! 2008 accord with solenoid malfunction. If I buy a salvage part, do I need to have the dealer reprogram or will it clear lights and codes / work automatically?
longitudinal acceleration Sensor malfunction Honda Accord 2016?
Code?
I have this same issue. Question? If i change the module to a new one or used do i have to program it?
I put in this new one no need programming not sure about brand new one it may need flahsing
Quick question, mine does come on and off and I do have a 2010 Honda Insight, could it be the same issue?
U have to scan it to get the codes
I am getting code 66-13 and 61-11 on a 2014 Honda accord sport. It says Pressure sensor inside of VSA modulator-control unit. Is this the piece I would need to replace?
Yup u can pull out ur old one and send it to abs moduel repair service it’s on eBay search it abs moduel repair it junk they charge $250
@@RBTheMechanic ok, thanks I will check it out. Dealer was trying to charge me 3k to fix it lol
Hey RB have the same issue with my same yr 2014 Accord sport. Just put a used module in drove it 20miles like the mechanic said to and lights still on SMH 🤦🏾♂️ can it be because the used module or could be something else?
Used moduel could be bad as well scan for codes ? And it’s better to send out ur old one to eBay service they will repair it for u
I have the power steering, traction, and tire pressure lights. The tire pressure flashes for a minute or so. I don't have the ABS light.
Can an auto parts store scan it?
Yeah autozone can scan the abs moduel for codes. Mostlikely this is what it is
RB where can I find a used ABS Control module for exact same car as this one? 2014 Honda Accord LX 2.4 L VTEC Please share a link on where you got yours.
eBay or send ur old one out for rebuild on eBay they have service to rebuild he charge $250
Lights are on but my transmission won’t hook does this part have to do with it
Prolly not
Thank you
I have 2016 Honda Accord LX,
I'm a beginner, can I do it?
And where can I get a long, flexible bar for loosening screws?
Everything I used u can buy from pepboys
Can I see the ebay module seller?
@@shop22600 the guy only had one search up LKQ it’s very big online junkyard they on eBay amazon all over base is in NY but u can have them ship it google up the name and number and give them a call
one more question RB. IfI take my module out for repair will my car still drive? Do you know who repairs these? Ordered twice off of eBay and they wont program to my car Tks
I don’t have answer for that because it’s not safe to drive without it but I had customer whole had me take it off so he can send it out and he drove back home like 12 miles and once he had it repaired he drove it back to me to install it but it dosent have stability control any more so it wouldn’t be safe to drive
I have the same issue, how do I find the correct part number? Where do I buy the part? I have a 2014 Honda accord.
Best option is have the moduel removed and on eBay they have rebuilding service send out the moduel and once u recieve it back install it and ur good to go
I drive a 2013 Accord touring. I got LDW, FCW, traction, tpms, steering lights on my dashboard. Any advise can I drive with these lights on? Or of i need to fix what is the solution
U can drive with it but u gotta fix the issue it may not have stability when needed scan the car for codes with high end scan tool take it to good mechanic shop
@@RBTheMechanic Thank You for replying and posting such amazing video
Hi where were you able to buy the solenoid, I’m having code 81-03 for yaw sensor. I’m assuming the new solenoid would fix it
Well this is all built in so u have to buy the whole moduel but u can calabrate the yaw rate sensor with scan tool
I have 2017 Accord sport but mine the check engine light comes on along with the traction and steering But then they’ll go away on there own and usually they’ll come back on once a week
Scan for codes
@@RBTheMechanic the crank sensor code came up. And I replace it and so the car would be good and suddenly the lights turn on and when I turn off the car and turn it on there gone it’s been going on for about 2 months
Help! My car is a Civic 2013 EX-L, show code 81-19, i need to change the module?
U might want to do yar rate calibration with high end scan tool
the same thing happens to my honda accord 2014 lx all those lights are on I wanted to buy a used module but the only ones I find are from an ex of the same year I would like to know if it works even though it is not the lx version?? I would appreciate your help
I’m not sure I think they all are same but just to let u know there is this service on ebay u send them ur old moduel and they rebuild it cost is like $250
Yo bro!! Awesome vid. Dealership said I had to change the abs modulator AND the fuse box?? Why do you think they trying to change the fuse box?? I get the module being changed but do you think they cmjust trying to get more money out of me by changing the fuse box?
Sorry not fuse box but they mentioned a relay box??
They crazyyyyy there’s fuse in there I would check that it’s like circuit multi fuse it says abs on it. Anyways there’s this guy on eBay search him up repair abs moduel u can send him ur old one and he will repair it and send it back like $250 and u can change it ur self!!!! Easssy
Thank you so so much!!
You welcome was this video help to resolve ur cars issue?
What type/size of bolts are holding that module to the pump? Torx T10?
Torques I think so that’s the number
This is happening with my Honda. Changed the right rear wheel bearing and all these codes would start to come on and off. Doesn’t affect my driving but idk what else to do
What code u have?
38-11, need a new abs module
Thank you so much man,
Your video it’s work,
Thank you, thank you, thank you much.
Welcome!!!!!!
Do you do the repair for the module and if so how much 2013 Honda Accord ex.
I don’t do repair I send it out my labor is $$190 +storages charges while the moduel is out for repair and the service of the repair faculty is around $250
Hello RB
My car is giving FCW failure. The moment car drive off few hundred yards D3 comes in with fcw failure with very less power on the engine. I tried to disconnect battery terminal but the problem still persist. I went to auto zone for odb sensor it came with battery malfunction . I don’t think this is the battery issue because it was changed recently. U0402-68 and P2101, 16-13, 83-11 and 61-11
Thanks in advance!!
U need to fix the d3 issue and moduel need fixed
@@RBTheMechanic Any idea about cost?
@@kamranmuhammad2474 not sure about the d3 light but this moduel I show u can have it rebuilt from eBay service cost is $250 and labor to remove and replace $190
How do u tell its the module or just an abs sensor?
By code what’s the codes u get if it gives u internal selonoid codes then it’s this part I show
@@RBTheMechanicI'm trying to pull codes. The codes go on intermittent.
Hey RB, can you drive while the black module is being repaired?
I wouldn’t recommend it not safe car can loose control
Thanks for the video. Where are you located by the way?
I’m in north nj Bayonne
Thanks for Video...
Thank you for the excelent video, where can I buy the vsa module?
eBay or go brand new from dealer
I do have same issue with my Accord coupe, i will try your solution today and i hope it will be fix, BTW, sometime with bad road condition when i press the break its feels like empty and i just replace the old break with new and everything is good but sometime in bad road condition when i press the break it feel like empty do you think i have the same issue,( i do have the same light and i went to mant mechanic and they all said everything is good under the car please advise.
It could be traction issue when on bumpy road or this abs is not working
@@RBTheMechanic the break issue showing on bad road and bumpy otherwise its good,, the ABS mark and steering mark is showing anyway in the dash same in your video
I have same problem on 2013 Honda accord but when I scan the code it shows 123-11 VSA solenoid valve malfunction is that same problem?
Same same
Maybe it's out of context but is it possible to replace a single solenoid valve from the hydraulic block? If yes where I can find a repair kit?
No u have to replace the whole thing search up on eBay abs moduel repair they service ur old one u just send it to them