Honda ABS Module TEAR DOWN what is casing this module to do bad on ALL HONDAs 2013 and above

Поделиться
HTML-код
  • Опубликовано: 29 авг 2024

Комментарии • 77

  • @TristanVash38
    @TristanVash38 2 месяца назад +4

    I'm about to perform this surgery right now. Got my kester flux, my silver rosin lead free solder, temp at 400, sponge is wet, LETS GO!

    • @RBTheMechanic
      @RBTheMechanic  2 месяца назад +1

      Good luck!!

    • @exisfohdr3904
      @exisfohdr3904 Месяц назад +3

      Silver solder is prone to cracking as it heats up and cools down. It should be fine, but lead tin would be better for this spplication.

  • @KB0WXR
    @KB0WXR 3 месяца назад +3

    Success for me! Thank you thank you! I used copper wire from Cat5 Ethernet cable. Original wires would not solder.

    • @RBTheMechanic
      @RBTheMechanic  3 месяца назад

      Nice!!!

    • @MrProtec
      @MrProtec 10 дней назад

      What soldering iron did you use? How did you ensure the wires weren't touching each other? Did you use the insulation from the Cat5 Ethernet cables? Congrats!

  • @user-wx5ed8tz3y
    @user-wx5ed8tz3y Год назад +3

    Thank you brother for clarifying the problem that it happened in my country, this car model has all the problems, and the service center refuses to take responsibility. They want customers to pay a lot of money to fix this problem. And there are more and more customers who have this problem in Thailand. I thought, like you, that it was a bad design and that Honda should have to recall to fix this problem, but it hasn't happened yet.

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      Yup they should defiantly recall it it’s bad wiring too thin contacts

  • @OGThinkster
    @OGThinkster 3 месяца назад +1

    Interesting.. I've had a couple times where I would get a bunch of lights on my dash all at the same time like Check Engine, ABS, Traction Control, etc. The problem went away on it's own and I figured it must be some intermittent sensor on maybe the Canbus or sensor data line pulling down that bus/line which would cause the ECM to think multiple problems. Well if it happens again, I will take a look at this module. Lucky for me, I have 30+ years of soldering experience so shouldn't be a problem..

  • @fredwilliams4661
    @fredwilliams4661 Год назад +5

    Thank you this was very informative. Great solutions too

  • @veramann
    @veramann 4 месяца назад +1

    Maybe I should go to a Honda dealer and ask one of the workers to find out if the ABS module for my 2013 Honda Accord is under recall or warrantee, so I can possibly avoid paying for the repair.

  • @hidesertdave6166
    @hidesertdave6166 7 месяцев назад +2

    Can a bad abs module cause stiff power steering on civic 10th generation? Very informative video

  • @live.esteticar
    @live.esteticar 5 месяцев назад +2

    Vamos ajudar com os defeitos 🚀

  • @aray4thearts281
    @aray4thearts281 Год назад +2

    Bro.. your AMAZING !

  • @sheerwillsurvival2064
    @sheerwillsurvival2064 Год назад +1

    Great information I watch’s German guy on RUclips solder a Jeep control box for fuel pump relay and it worked

  • @leetos.4915
    @leetos.4915 Месяц назад +1

    Did u get abs light on the dashboard for this? I’m facing similar issue with all the lights except I don’t have abs light and engine light. Likely it needs to be reset by a Honda tech professional scanner or any kind of scanner that would do the job to reset it.

    • @RBTheMechanic
      @RBTheMechanic  Месяц назад

      All the lights on dash and steering traction Tpms traction

    • @leetos.4915
      @leetos.4915 Месяц назад

      So you did have abs light on your dashboard. I thought about fixing my abs module too but not anymore since I don’t have abs light on my dash. It just simply means I’m having software issue somewhere else and the abs module is not involve with it…I finally figured out on this that it’s actually my steering wheel sensor need replaced also cuz I only replaced the clock spring last time I did the job. The steering wheel sensor as u may know is attached to the clock spring behind it.

  • @AdalbertoVALENCIA-hq8pr
    @AdalbertoVALENCIA-hq8pr Год назад +2

    Did you need to do any module programming when installing used module from ebay???

    • @RBTheMechanic
      @RBTheMechanic  Год назад +2

      No direct fit and good to go no programming

  • @Riverabuilt
    @Riverabuilt 9 месяцев назад +1

    So i replaced the abs pump due to one line not getting brake fluid to a caliper. I re installed my old module due to the car not starting with the one that came with the pump. Now i have all kinds of lights. Would it need to be re program?

    • @RBTheMechanic
      @RBTheMechanic  9 месяцев назад

      U messed it up even more. Moduel dosent restric brake fluid flow u need to track the line restriction

  • @215ftr
    @215ftr 3 месяца назад +1

    I have multiple light on my dash. Brake,fcw,abs, you think its also the connectors inside the box

    • @215ftr
      @215ftr 3 месяца назад +1

      Honda Accord 2013 exl

    • @RBTheMechanic
      @RBTheMechanic  3 месяца назад

      Scan the abs moduel for codes

  • @coreyandnathanielchartier3749
    @coreyandnathanielchartier3749 Год назад +2

    I still am amazed that so many people pay through the nose for 'quality' Japanese cars, when a Chevy or Ford will outlast them and require 1/5th the maintenance. I've made a good living working on Jaguar and Land Rover 'quality'. Leaking Nissans with trash go-cart transmissions, and yes, the classic Honda and Toyota electrical systems.

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      Yeah

    • @teenice894
      @teenice894 10 месяцев назад +2

      I've owned all 3... chevy , Ford, Honda . They all have their problems and I've replaced a transmission on my f150, Tahoe and accord... no car manufacturer gets a pass when it comes to repairs. It's a pick your poison type of thing with cars, if there was a perfect car everyone would be driving it

  • @chuygonzalez770
    @chuygonzalez770 Год назад +1

    hello, I have a question, my accord has that problem, it's a 2013 EX-L, it has to be the part specifically for the EX-L or it can fit from any other from that same year, something like an LX can work for my car even if the donor is not EX-L? Thanks

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      Same answer

    • @RBTheMechanic
      @RBTheMechanic  9 месяцев назад

      @@MrNormal593 not sure about civic accord is diffrent 13to 17 same

  • @0x00zero
    @0x00zero Год назад +1

    how do the professional rebuilders open them without cutting?

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      They cut them I seen it and glue it back

  • @servo5651
    @servo5651 Год назад +1

    RB Igot all the brake lights on at the rear. I checked the fuses. They good. I checked the brake light sensor. They good. I got the trifecta’s but the abs light turns off but push the break and it turns on. What should I look for 😊

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      Wait I didn’t u derstand. Brakes light are on in the back pulse they turn on with braking?

    • @servo5651
      @servo5651 Год назад

      @@RBTheMechanic no they don’t break only stay on

    • @servo5651
      @servo5651 Год назад

      The break lights are stuck on. I push the break and it stays the same. I disconnected the sensor under the break pedal no changes

  • @BuiltDifferent13
    @BuiltDifferent13 Год назад +2

    Nissan is good if it's RWD manual transmission

  • @osamaabdelnaeem4326
    @osamaabdelnaeem4326 2 месяца назад +1

    I have the same problem with Honda pilot 2014 what can I do?

    • @RBTheMechanic
      @RBTheMechanic  2 месяца назад

      First scan the car for codes in all moduel especially abs moduel

  • @user-pm3bp6cq4x
    @user-pm3bp6cq4x Год назад +1

    Love your videos
    Is it safe to go through eBay. I had a electric laboratories say you need to reprogram it and it could be dangerous when it rains (locking of the brakes).

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      Yeah i had one or 2 people do the rebuild off eBay and it was smooth car was fixed

  • @daviddeleon5483
    @daviddeleon5483 Год назад +1

    Does the throttle module is integrated on the abs/vsa module?

    • @RBTheMechanic
      @RBTheMechanic  Год назад +1

      No throttle is processed by ecm engine control moduel

  • @maverickperson5443
    @maverickperson5443 10 месяцев назад +1

    would you know if 2012 Honda Civic EX will have the same abs modulator pump or this poor design started from 2013? Thx

    • @RBTheMechanic
      @RBTheMechanic  10 месяцев назад +1

      It can but I haven’t had any come yet

    • @maverickperson5443
      @maverickperson5443 10 месяцев назад +1

      @@RBTheMechanic thx - I have VSA light and randomly power steering light kicks in, never had ABS light. Any idea what could it be? Planning to scan for the VSA codes.

    • @RBTheMechanic
      @RBTheMechanic  10 месяцев назад +1

      @@maverickperson5443 scan for codes first

    • @maverickperson5443
      @maverickperson5443 10 месяцев назад +1

      @@RBTheMechanic seeing two codes 81-20 and 85-01. Battery was recently tested and showed needs to be recharged(alternator is good), can it be bad battery?

    • @RBTheMechanic
      @RBTheMechanic  10 месяцев назад +1

      @@maverickperson5443 u need to replace that battery before anything

  • @vedranvedran6078
    @vedranvedran6078 Год назад +1

    Sir thank you very much for this video. Great explanation.
    I am having the same problem. Lights are on (ABS , traction control…)
    however they go off when temperatures are low and it’s cold outside.
    I went to Honda and they confirmed my fear, ABS modulator. I haven’t fixed it yet but they only did diagnostics. $1700 for a part and $ 250 labor. Just was wondering if you have any opinion why this problem is not there when it’s cold outside like 40 degrees Fahrenheit and do you suggest I sent part to be fixed ?
    Thank you

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      Yes I would send it out

    • @vedranvedran6078
      @vedranvedran6078 Год назад +1

      Thank you so much for your response!
      I heard you said eBay for repairs, could you please suggest particular name of service/business on eBay that I should go with ? Thank you again

    • @RBTheMechanic
      @RBTheMechanic  Год назад

      @@vedranvedran6078 u have to search on eBay type is honda abs moduel repair. It should show up and send them message they will guide u

  • @JordanySierra
    @JordanySierra 5 месяцев назад +1

    The abs módulo 3.5 and 2.4 are the same ?

  • @user-oz8zq8xj6s
    @user-oz8zq8xj6s 4 месяца назад +1

    I opened my module up and tried to solder it. I couldn’t get the solder to stick to the connections. I took it to 2 different cell phone repair shops and they couldn’t get solder to stick either. Is it a specific kind of solder? Is anyone else having this problem too?

    • @AshutoshMishra-qg1eq
      @AshutoshMishra-qg1eq 3 месяца назад

      Did you try using some flux?

    • @KB0WXR
      @KB0WXR 3 месяца назад +2

      I had success removing the coating on the board and contacts and using new solid copper 26 awg wire(from cat5 cable). Original wire is welded on and will not accept solder. I had 4 broken wires. Replaced, reinstalled and no codes.

    • @TristanVash38
      @TristanVash38 2 месяца назад +1

      @@KB0WXR thanks for this tip. I'm about to do all of this right now.

    • @lanthonyperdum6430
      @lanthonyperdum6430 14 дней назад

      @@KB0WXR…Great…Possibly could you assist me in repairing mine as well ???

  • @215ftr
    @215ftr 4 месяца назад +1

    Can i just go to the junk yard and take one out from a crash honda accord ?

    • @RBTheMechanic
      @RBTheMechanic  4 месяца назад +1

      Prolly get same BS better to send it to get repaired

    • @215ftr
      @215ftr 4 месяца назад

      @@RBTheMechanic should I check other things before shipping it out ? Like checking brake fluid and tire sensors?

  • @BuiltDifferent13
    @BuiltDifferent13 Год назад +1

    They make my favorite motorcycles but outside of that I'll pass... They make great generators great lawn mower engines motorcycles like I said but If I want a car I'll drive a Toyota or a Ford