Видео

Son we did not watch the video to see you😂 you should show what you are doing 😯

Need help, steer tire on crown Service Manual PF25002-00M, model sc5200 2016, it's stuck steer tire one position

I have a hyster and I have the same problem, it won't start, I think it's the same as that one. I'm in Miami. Can anyone in this area fix it?

Those brakes look cool! But so weird. I didnt know this sort of brake existed.

What about viper forklifts?

What’s the part number for that mother board? Currently working on one. The part provided was very alike but different. Thank you

What is the difference between the clutch cylinder & master cylinder?

what programming tool is needed (how do you purchase it) and what are the correct parameters to put in?

I fix those all the time in a freezer they suck ..the head of the allen bolt get stripped all the time, the only thing i never replace is the controler/drive unit those seems to be bulletproof. Raymond usualy always have the harness in stock and its cheap but of course you're not always close to a raymond dealer . I enjoy your video alot ive been learning alot on propane those are my weakness as i'm more a electric forklift kind of guy . Cheer from Montreal .

Hey bro do you know how to get rid of code c46

Is the owners name Jack Hackery?

Code 5:180

Eait that light thing ain't true?!?!??!😅 oh snap

lol amazing how they act like they know when they didn’t even know where to check the water coolant

Je suis Français et je travail également sur du Hyster, j’adore vos vidéos! 👍🏻

Hey Elmer you don't know me but I committed on one of your videos , knew the parts guy at Toyota. Well talked to Gary a couple of days ago, haven't spoken since he left Mass Toyota dealership. He had nothing to say but good things about you. Just thought I'd let you know

How about Kalmar? I have a few older 30,000 lb capacity Kalmars with volvo diesel engines that I really like. We are upgrading to a newer 30K capacity forklift and am trying to avoid clarks and hysters but not very many used Kalmars out there.

Good afternoon. I have the same pallet jack. Is it common for the control card to die? I have nothing on the led panel and no lights on keypad. I’ve checked the batteries and fuses and everything looks good. The Curtis controller Is blinking yellow so it’s definitely getting power. Is there anyway to test the control board before I purchase a replacement?

Very helpful! What you added into the radiator?

Blessed to have your father working side by side with you. You can tell he’s very knowledgeable, and it’s cool that he’s passing that on to you.

I need your help with a SP like soon

Hi can you help me I have a toyota palte jak with code 66

Awsome video I'm about to service one of these Wednesday. What kind of oilfilter brand and number did you use. Carquest said the Carquest 84145 will work on it

I appreciate what you do here. I have a question. I'm working on this Heli forklift that doesn't go forward nor reverse, and I've changed the transmission pump cos I realised it was weak. My question is, why do I not see oil pressure when I remove the solenoid valve from the valve body when I start the engine?

I’m a tech for Walmart and one of my stores has a 2016 Raymond 8210 where the forks won’t lower, no pump no nothing when trying to lower them but the pump starts when you to raise them. Walmart says it’s time to replace it but the store likes its speed and really wants me to repair it. A new tiller is $2200, do you think if I got one it would fix the problem? I’m getting that new load wheel axle tool that I said I was getting this week.

I have a sit-down Toyota forklift, it backfires, also when you press the gas down it backfires and starts to die until it goes dead, also I found that when on it blows out the filter and cap like a cannon what could be going on? Help plz

How do you adjust the parking brake on a forklift with wet brakes?

They primarily leak from the 90 degree elbows off those lines. The o ring get rock hard

Those T/C cooler lines always leak🤣 I’ve never seen on get past a few thousand hours without at least seeping.

I just did this Job yesterday,and the transmission was slipping. Topped off fluid and now it won't move. Tranny line's, o-rings filter and replaced transmission fluid. Fluid was a little bubbly. Monday project I guess,. Fluid flow test?

Awesome 😎

Don't forget to change the brittle perished o ring on the inside of the 90° fittings.. trans fluid leaks past the fitting more often as they get older and leaks onto the back of the hose, not out of the hose 💪

that sticker is the best

Did he say dicksss… Gay!

According to hyundai those disks have to be soaked in ATF before installing. Yet again thats for a 160d. Lmk if you ever need any hyundai or unicarrier service manuals. I work for the dealer here in colorado but have files of tons of service manuals for all kinds of equipment.

awesome work and awesome explanation. 👍👍

Amazing & Helpful! I love how it raised the forks when you depressed the raise the forks control. Who would have guessed?!?!

I’m a technician at a Hyundai forklift dealership. I have the service manual pdf if you need it.

Brake dust get you some it won’t hurt you‼️

Yo Elmer, you need a special lap top like this tough book or i can get the software For what makes and models? If you were to change the display i know it comes in blank you think you can program it with this?

Yo Elmer, you need a special lap top like this tough book or i can get the software on a regular HP and just buy the tool, does it come with the wires to hook up? For what makes and models? If you were to change the display i know it comes in blank you think you can program it with this?

Im getting ad-4 ad-6 ad-3 ad-5

How much did you charge your customer for that fix ?

How did you manage to stop the squealing or squeaking

Same guy that took care of the Kubota took care of this job. Good on him

Those hose are trans cooler hoses. Normally leak from o-ring on the 90s on trans

My man said, the problem was in the valve body boyyyy lol you live you learn, keep it up boy,

I work for hyster Yale dealer our wet brakes use ATF

ima lift truck tech here in canada thinking of applying to Tekamo to go alone. do you recommend that? been doing it 5 years

Good job, I can retire now