How to Install the firmware of crossflight?
HTML-код
- Опубликовано: 29 июл 2023
- The parameters of crossflight can be set in RadioLink Mission Planner, ArduPilot Mission Planner, and QGC, but crossflight can only install the firmware by RadioLink Mission Planner and only supports RadioLink firmware.
The Mission Planner can be downloaded from RadioLink official website (附crossflightwww.radiolink.com/crossflight....
Here is RadioLink Mission Planner for crossflight. It has already been downloaded on the computer.
The default firmware of crossflight is for Multicopter. You can install other firmware you want.
Connect crossflight to the computer via the USB cable, which comes with crossflight. (Do not install new firmware by wireless data transmission)
After connecting it, click SETUP--Install firmware. Before installing firmware, we must check if crossflight is recognized. It can be seen in the status here. If it is not recognized, unplug the cable and plug it again.
(Do not click CONNECT when installing the firmware)
It pops out found board here, which means crossflight is recognized now.
There are two ways for you to select the firmware and install it. You can either click the icon directly to install the firmware or click Load custom firmware to install the firmware you downloaded from RadioLink website.
Are you sure you want to upload ~~~？ YES. Platform- select crossflight--Upload Firmware. The green bar is moving. The blue LED is also flashing when installing the firmware.
Now firmware is installed.
Select the COM port and baud rate. (Note: Baud rate is 115, 200 for USB cable)
Then click CONNECT. Keep crossflight still and wait. Now connected. Move the crossflight and we can see it connects well.
For more details of crossflight flight controller:
www.radiolink.com/crossflight
Purchase link of crossflight flight controller:
www.radiolink.com/crossflight...
You can send emails to after_service@radiolink.com.cn if you have any questions when using our products.
#rcplane #rcairplane #flightcontroller #radiolink 
Авто/Мото
BRAVO! BRAWO! THANK, thank! Have a nice day!
Thank you for your support. Nice day!
My radio calibrations are not working. Transmitter is bound correctly to the receiver , but there is no signal seen in radio calibbration. Can you help?
Hi, sir. The radio calibration not work because there is no successful connection between the receiver and flight controller. crossflight supports standard PPM/SBUS signal. Could you please confirm your receiver support standard PPM/SBUS signal? And the connection should be correct. If there is still any question please feel free to contact us. Our email is: after_service@radiolink.com.cn
Radiolink crossflight flight controller update karne ke bad minipix-v2 dekha rha hai aab kya karna hoga
Hi, sir. Sorry we do not clearly understand what you mean. Do you mean that CrossFlight is not recognized by the computer? You can enter Device Manager to check the COM port. And what Mission Planner are you using? You can use RadioLink Mission Planner to have a try. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Ardupilot mission planner doesn’t show cross flight or multicopter. How do we do it?
Hi, sir. Sorry Ardupilot Mission Planner does not show the COM port of CrossFlight. But you can check the COM port of CrossFlight from the Device Manager of your computer. And you can check more difference of RadioLink Mission Planner and Ardupilot Mission Planner from the link here: www.radiolink.com/crossflight_missionplanner If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
I am getting red led blinking on flight controller after firmware installation and flight controller is not connecting
Hi, sir. It is possible the firmware update is not successful or the wrong firmware installed. Could you please make sure you have installed the right Mission Planner and firmware? www.radiolink.com/crossflight_missionplanner www.radiolink.com/crossflight_firmware Then you can follow the tutorial to install the firmware. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Radiolink crossflight flight controller ko jab leptop se connect kar rhi h to com nahi le rha hai uske liye kya kare
Hi, sir. Sorry we do not clearly understand what you mean. You connect CrossFlight to the computer to connect Mission Planner and adjust parameters. You don't need to charge CrossFlight, and you cannot charge the battery by the computer. Could you please let us know more details of your problem? Our email is: after_service@radiolink.com.cn Here is the detailed manual of CrossFlight for your reference： www.radiolink.com/crossflight_manual
I have a perches new radiolink cross flight controller plz make a video for full setup x copter drone with parameter help me plz
Dear Sir. Thank you for your support. If you are using helicopter, you can check these videos for crossflight. ruclips.net/video/um655Uxnqnw/видео.html www.youtube.com/@Radiolink_official/search?query=crossflight And for setup on helicopter, could you please check the detailed manual of crossflight for helicopter? Here is PDF file of the detailed manual to show how to setup crossflight on helicopter. www.radiolink.com/crossflight_manual The manual introduce more details on it. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Make a full drone setup with all connection plz make a video or given me link
@@Ashish_kumar_Raigarh Hi, sir. The setup and connection of a drone are included in the detailed manual of crossflight. Could you please check the manual link here?www.radiolink.com/crossflight_manual Because it contains so many contents, which is hard to take videos of all of them, there is no video available. But I'll send your feedback to our team and hope more videos of crossflight will be available in the future. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
after reset radiolink cross flight contler. necessary to update firmware?
Hi, sir. The default firmware is for multi-rotor. If depends on if you have installed any other firmware. You can install the firmware you want. Reset only reset the parameters of the current. It won't change firmware version in your CrossFlight. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Hello, assistant, I would like to know; I have a 35 amp Aligne Bl35 esc, would it work on Crossfligh?
Hi, sir. CrossFlight supports ESC of PWM, DSHOT and ONESHOT. If your ESC supports them, they can work together. The current and the voltage of ESC depends on your power supply and motor. For example, if the power supply voltage exceeds the working voltage of the ESC, the ESC will be burnt. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
thank you very much for responding. I have a lot of doubts: what the letters DSHOT and ONESHOT mean.
@@MrCADU267 It is the protocol of ESC. You can ask for the seller of ESC for more details. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
what is the bootloader update one? do we leave that alone or update it - says may brick the board?
Hi, sir. You can update the firmware of CrossFlight directly. You can check more details from the link here: www.radiolink.com/crossflight_firmware Just install RadioLink Mission Planner here: www.radiolink.com/crossflight_missionplanner If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
realy brick my cross flight . now its getting red loght blinking
@@r.v.p3759 Hi, sir. There may be something wrong with your firmware. Could you please follow the tutorial here to update the firmware? ruclips.net/video/cfnlPB6ei_0/видео.html&lc=Ugy1IrMpbVJ1kUB5X694AaABAg And CrossFlight only supports RadioLink firmware. You can download the firmware here: www.radiolink.com/crossflight_firmware And we also recommend you to use RadioLink Mission Planner to have a try: If there is still any problem, could you please take a video to us? Our email is: after_service@radiolink.com.cn
Please, what is the difference between the blue version 1.0 and the black version 2.0?
Hi, sir. The blue version is CrossFlight. The black version is Mini Pix. Here is the comparison of them for your reference: www.radiolink.com/newsinfo/841014.html If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
OK. Thank you very much 🙂🙂😉 please, just one more question, does this crossfligh have an anti-vibration system? How is activation done?
@@MrCADU267 Hi, sir. Yes. CrossFlight has Vibration Damping by Software. The actual effect may varies for different models. Here is the link of CrossFlight for your reference: www.radiolink.com/crossflight
im getting gps errors when i covered the fc with 3d printed dome
Hi, sir. What GPS are you using? What error did you meet? Could you please follow the prompt to solve the problem of GPS? If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official I've been using ready to sky m8n gps ,after calibration it is showing "error compass variance",and getting mag values as prearm check,and no gps ubloc detected,and fc barometer calibration is not responding
@@FLYHIGHDIY It's probably because of large disturbance. Remove all possible disturbances such as metal parts on aircraft frame. compass and GPS signal. If the notice is still there, calibrate the compass and repower it on afterwards.
the default is multicopter : is that mean quadxopter or what else ?
Hi, sir. The default firmware is for all multi-motors, so sure it is compatible with quadxopter. And you just need to select Frame type in Mission Planner and then set it. Here is the detailed manual of CrossFlight for your reference. www.radiolink.com/crossflight_manual_download If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official can i use it without any configuration for a quadcopter like plug and play ?
@@omnianti0 No, sir. You need to set parameters according to your models. You can check how to use the flight controller from the detailed manual of CrossFlight. Here is the link for your reference. www.radiolink.com/crossflight_manual If you want to plug and play, you can try our aircraft with flight controller on it, such as RadioLink F450, F330 and M435. Here are the links for your reference. www.radiolink.com/f450 www.radiolink.com/f330 www.radiolink.com/m435 If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official is the factory default parameters do not fit an existing model as those you are selling ?
@@omnianti0 Hi, sir. Parameter adjustment and configuration are required when using flight control and any aircraft. If you do not want to set or configure, you can select our aircraft with flight controller on it, such as RadioLink F450, F330 and M435. The set and configure are already done in the factory. Here are the links for your reference. www.radiolink.com/f450 www.radiolink.com/f330 www.radiolink.com/m435 If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
im getting red led blinking on fc after firmware installation and fc is not connecting
Hi, sir. Did you install the firmware successfully? And do you mean that you click CONNECT. but it cannot be connected? Could you please first make sure crossflight is successfully recognized by the computer, and select the right COM port and baud rate. If there is still any question, could you please send a video to our email after_service@radiolink.com.cn ?
@@Radiolink_official I installed ardupilot firmware bymistake now it's fine no issue,,thank you
I've just had the same problem. Any news there? Thank you.
@@arrober Hi, sir. Did you install the firmware successfully? Could you please re-install the firmware and make sure the firmware is installed successfully? Also make sure you have instaklled the right firmware. Here is the download link of the firmware for crossflight: www.radiolink.com/crossflight_firmware If there is still any question, you can send details to our email after_service@radiolink.com.cn
@@arrober just reset everything in software in parameters list
its getting red light blinking how to slove it
Hi, sir. There may be something wrong with your firmware. Could you please follow the tutorial here to update the firmware? ruclips.net/video/cfnlPB6ei_0/видео.html&lc=Ugy1IrMpbVJ1kUB5X694AaABAg And CrossFlight only supports RadioLink firmware. You can download the firmware here: www.radiolink.com/crossflight_firmware And we also recommend you to use RadioLink Mission Planner to have a try: If there is still any problem, could you please take a video to us? Our email is: after_service@radiolink.com.cn
thanks my problem has solved after update firmware with Mission planner radiolink . Thanks alot .
@@r.v.p3759 Great to hear that. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Who is your official distributor in india
Hi, sir. Here is the purchase link of CrossFlight from our distributor in India: robu.in/product/radiolink-crossflight-flight-controller/ If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Wt the gpio ports in cross flight send them here
Hi, sir. Sorry we do not clearly understand your problem. Do you want to calibrate the compass with GPS? Here is a tutorial for your reference. If this is not what you want, is it convenient for you to let us know more details of your problem? Then we'll help you solve it. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official GPIO pins
How to reboot the crossflight controller
Hi, sir. You just need to unplug the USB cable and then connect the USB cable again. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Thank you for reply
But one more problem
After uploading firmware the crossflight controller com port is not connecting to the computer and always blinking red light
Please help
@@user-um8vi9dc9q Hi, sir. 1.Please make sure you have installed the correct firmware for CrossFlight. 2.Make sure you select the right COM port and baud rate. You can go to Device Manager to check the COM port of CrossFlight. And if you connect USB cable, you need to select 115200 for baud rate. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Arming problem hai
Logging failed ka message aa raha hai
Please help me
@@user-um8vi9dc9q Hi, sir. Logging failed means Logging pre-armed was enabled but failed to write to the log. Here is the link for your reference. ardupilot.org/copter/docs/common-prearm-safety-checks.html If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Телеметрию на пульт не передайот через PRM-3
Hi, sir. What transmitter and receiver are you using? PRM-03 can only work with R9DS/R12DS receiver and AT10II/AT10/AT9S Pro/AT9S/AT9 TRANSMITTER. Make sure there is right connection. Here is the detailed manual of PRM-03 for your reference. www.radiolink.com/prm03_manual If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn