Видео

Hi, sir. Sorry you cannot adjust the display time. But I can send your feedback to our engineer. Hope it can be achieved in the future. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Thank you for your support

Hi, sir. If you are using RC6GS V3, you can download the firmware of RC6GS V3 from the link: www.radiolink.com/rc6gsv3_firmware And you can follow the tutorial here to update the firmware: ruclips.net/video/XLyTnSlou-4/видео.html If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. Thank you for your support. Sorry we do not have related devices. But you can refer to the above tutorial to connect it to AT10II. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. Here is a related tutorial: www.bilibili.com/video/BV1f64y1C7ik But sorry it's in Chinese. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. Here are our suggestions for you: 1. You can install the other firmware on CrossFlight. After that, you can install the firmware you want again. Here is the tutorial to show how to install firmware of CrossFlight: ruclips.net/video/cfnlPB6ei_0/видео.html 2. You can reset crossflight to factory setting. Enter CONFIG--Full Parameter List-- Reset to Default. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. Yes. T16D and T12D is good for tracked rcs like tanks excavators etc. You can make your own video for each switch. Here is the link of T16D for your reference: www.radiolink.com/t16d If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Dear Sir, Sorry for the problem. 1. Could you please test RSSI? You can use new receivers to test RSSI, which can help to confirm if the problem comes from the receiver or transmitter. Here is RSSI testing tutorial for your reference: ruclips.net/video/RA0NasTZS90/видео.html 2. If the signal loss problem happens when you move the throttle or wheel of RC8X, it is possible that the problem is caused by insufficient BEC power supply. Here is the link for your reference: www.radiolink.com/newsinfo/561234.html 3. May I know how you install your receiver antenna in your car? There is also some requirements for the receiver antenna installment. Here is the guide of receiver antenna installment for your reference: www.radiolink.com/newsinfo/886600.html So could you please check and follow our suggestions above and let us know your answers? You can also send us your RSSI testing process. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Dear Sir, Sorry for the problem. 1. Could you please test RSSI? You can use new receivers to test RSSI, which can help to confirm if the problem comes from the receiver or transmitter. Here is RSSI testing tutorial for your reference: ruclips.net/video/RA0NasTZS90/видео.html 2. If the signal loss problem happens when you move the throttle or wheel of RC8X, it is possible that the problem is caused by insufficient BEC power supply. Here is the link for your reference: www.radiolink.com/newsinfo/561234.html 3. May I know how you install your receiver antenna in your car? There is also some requirements for the receiver antenna installment. Here is the guide of receiver antenna installment for your reference: www.radiolink.com/newsinfo/886600.html So could you please check and follow our suggestions above and let us know your answers? You can also send us your RSSI testing process. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. This is our new product, which will be available soon. After it comes out, you can buy it from our AliExpress official store. Here is the link for your reference: www.radiolink.com/t12d If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. Could you please test RSSI in about 30 centimeters? Here is a tutorial for your reference: ruclips.net/video/jr7ad-_MVoI/видео.html And may I know if you have any other receivers? If yes, could you please test RSSI with different receivers to confirm if the problem comes from the transmitter or receiver? If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

@@Radiolink_official sadly i dont have any spare receiver. When i do RSSI test it reads around -60, -57.

@@baskabisi453 Hi, sir. Could you please send your RSSI testing process video to our email after_service@radiolink.com.cn ? It will be helpful for us to help you confirm the problem. Thanks in advance.

@@Radiolink_official okey i'll be sending the video in a few hours. Thanks for your help though its like the best customer support i have ever experienced 😀

@@baskabisi453 Thank you. It is our pleasure.

Hi, sir. PRM-01 can only connect to RadioLink R9DS or R12DS receiver. So it may not be able to connect to your arduino uno. Here is the link of it for you to better know about it: www.radiolink.com/prm01_manual

Hi, sir. The channels of Byme-A if four channels. Byme-A does not support CRSF protocol, so sorry it cannnot use ELRS receiver. But you can use SBUS receiver with it. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

@@Radiolink_official you can get sbus crsf now - radiomaster er8gv

Hi, sir. If you connect TBS Crossfire to RC8X, you don't need to use R8FG receiver. You just need to use the crossfire receiver. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Thank you for your feedback. We'll improve it in the future. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. Thank you for your support. You can buy it from this link: www.radiolink.com/D460_where_to_buy And we are pleased to apply for a discount for you to buy one. You can contact us via email after_service@radiolink.com.cn If any question about RadioLink products please feel free to contact us.

Hi, sir. You can check the setting of the battery fail safe from the detailed manual of CrossFlight: www.radiolink.com/crossflight_manual And for the PreArm error, you can check all the solutions of PreArm from the link: ardupilot.org/copter/docs/common-prearm-safety-checks.html If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. If steering is reversed, you just need to enter the REVERSE setting menu, and set the CH1 to REV. You can check more details from the detailed manual of RC6GS: www.radiolink.com/rc6gsv3_manual If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

@@Radiolink_official I found it lol

@@jglawncare2010 Great to know that. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn

Hi, sir. Sorry for the unpleasant experience. May I know if there is any problem when using CrossFlight? If yes, please feel free to contact us. Our email is: after_service@radiolink.com.cn We are ready to help you solve it. Thank you.