Setup and Connect DJI Digital FPV System to crossflight/Mini Pix/PIXHAWK
HTML-код
- Опубликовано: 4 окт 2024
- How to setup and connect DJI digital FPV System to RadioLink flight controller crossflight/Mini Pix/PIXHAW? Since the setup and connection method is the same for crossflight/Mini Pix/PIXHAWK, take crossflight as an example in the video.
I’ll show the connection first. Here is the power module of crossflight. Connect it to the POWER port.
Here is the RadioLink adapter board which is used to connect DJI digital FPV System and crossflight. It can not only supply power to DJI FPV System, but also transmit the signal. You can buy it from our official store. The purchase link will be available soon.
The adapter board comes with several cables. One cable is soldered on the power module. The other end of the cable is connected to B+, positive pole and GN, ground, on the board to supply power to the FPV System.
(Power module supports 2S-12S battery power input, while DJI air unit supports 2S-6S power input, so you can use 2S-6S battery to connect to the power module.)
Here is another cable comes with the board. Plug one end to the 3 pin connector on the board, and the other end to the telemetry port of crossflight. Both TELE 1 and TELE 2 can work. I connect it to the TELEM1.
Here is DJI FPV air unit. Connect it to the adapter board. Refer to the illustrations on the screen to connect the air unit to the board. (Note: If the cables on the air unit are not soldered, follow the illustrations on the screen to solder the cables) Check the printed words on the board and then connect.
We can see there is also another connector on the board. What is it for? It shows SB, SBUS and GN, ground. The connector is specially for DJI FPV system. There may be built-in receiver in the air unit. When you use DJI transmitters, you can use the built-in receiver to transmit signal to crossflight. We need this cable which comes with the adapter board. Plug one end to RC IN of crossflight, and the other end to the connector here. Then we can use DJI transmitters to work with crossflight. If you do not use DJI transmitters, you can just use the original cable of crossflight to connect the receiver.
After the connection, set parameters in Mission Planner now. Connect crossflight to the computer with a USB cable. Select the right COM PORT. The baud rate is 115,200. Connect. Connected now. Config--Full Parameter List-- We need to search two parameters and set it.
1.search serial1, here is SERIAL1-PROTOCOL. Select DJI FPV. If you connect the adapter board to telem 2 of crossflight, please set SERIAL2-PROTOCOL to DJI FPV. click WRITE PARAMS to save the modification.
2.Search OSD, hyphen, TYPE. Select MSP. Click WRITE PARAMS to save the modification.
You’d better also power off crossflight and re-power it on after the modifications.
The settings of crossflight in Mission Planner is done. Now connect battery to the power module of crossflight, and the DJI air unit will be powered on.
Here is DJI FPV goggles. Power it on. (DJI FPV goggles supports 2S-4S power input)
You must link the air unit and DJI FPV goggles. Check their detailed manual for linking methods or follow the methods on the screen.
The linking is already done. You need to set one parameter on the goggles. Settings-- Display-- Custom OSD. Set it ON. Then we can get OSD in the goggles.
For more details of crossflight flight controller:
www.radiolink....
Purchase link of crossflight flight controller:
www.radiolink....
For more details of DiViT adapter board:
www.radiolink....
Purchase link of DiViT adapter board:
www.radiolink....
You can send emails to after_service@radiolink.com.cn if you have any questions when using our products.
#fpv #dji #goggles #pixhawk #radiolink #crossflight
Very helpful video for FPV user. One thing you have to check. In the DJI FPV Air unit manual, the external power source for the air unit is within 7.4 ~17.6 V (2S~4S). Otherwise, air unit may be damaged. To use 6 cell battery will damage the DJI FPV Air unit, I think.
Hi, sir. Thank you for your feedback. Yes. It is necessary to check the voltage range before you connect a bettery.
connect analog vtx equipped with smart audio, so you can set power, band, channel via the osd screen. thank you
Hi, sir. We have connection diagram of CrossFlight to analog VTX. You can send email to after_service@radiolink.com.cn Then we can send it to you via email. If any question, please feel free to contact us.
Bro radiolink crossflight flight controller ko update karne ke bad crossflight ki jaga minipix-v2 dekha rha or na hi USB cable le rha hai uske liye kya kare
Hi, sir. Sorry we do not clearly understand what you mean. Do you mean that CrossFlight is not recognized by the computer? You can enter Device Manager to check the COM port. And what Mission Planner are you using? You can use RadioLink Mission Planner to have a try. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Make video how to connect with Skydroid T-10?
Hi, sir. We have already made a video to show how to connect our flight controller to Skydroid T10. And the connection method is the same for crossflight. You can check the tutorial here. ruclips.net/video/-rJuC6j4ed0/видео.html If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Thanks mate, can you Tell me If the conection with Skydroid H12 with Crossflight is the same? Do I need some adapter? Thanks in advance
@@DroneFishingBrasil Hi, sir. Sorry we do not know about skydprid T12. Here is the link of how to connect Skydroid T10 to Mini Pix/PIXHWK. You may have a check. ruclips.net/video/-rJuC6j4ed0/видео.html It introduces more details here. From this video, we think you may need to modify the connector. Because the telemetry port may need to be modified. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official yes, there is no problem to modify the connector, once I understand which modification I need to do in order to connect to telemetry port. I am still working on that and I will let you know when I got any updates. Cheers
@@DroneFishingBrasil Great. By the way, when you make it, could you please take some pictures of crossflight and Skydroid H12 to us? Our email is after_service@radiolink.com.cn And we look forward to your feedback.
I do not have the power module for crossflight, instead I have power module for Pixhawk 2.4.8 how can I connect the power cable to this module? Or there are any other options to power up the air unit? I use 3S battery.
Hi, sir. You can also use the power module for PIXHAWK to connect the board. And you can also use other methods to supply power to the air unit. For other methods, please contact DJI after-sales for it. Pay attention the power supply voltage does not exceed the working voltage of the air unit. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Y a t’il d’autre alternatives que le divit, disponible sur Amazon svp, car besoin rapidement
Hi, sir. DiViT is an adapter which is specially designed for our flight controllers. Sorry there is no alternative. You can buy it from Amazon. Here is the link for your reference: www.amazon.com/Radiolink-Transmission-Walksnail-compatible-crossflight/dp/B0CJ2D3XZS If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Hi, can you see the drone's battery voltage?
In the DVR
@@deltadrone Hi, sir. Yes. You can see the drone's battery voltage in the goggles. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
My cat does that with yarn all the time.
Sounds interesting!
I want to connect my RunCam digital vtx to pixhawk cube orange and also want the osd data on dji googles v2. Is it possible?
Hi, sir. You can check if the diagram of PIXHAWK and RunCam digital vtx match, just like the connection in the video. If their connectors match, you can connect them by following the tutorial. And for how to bind RunCam digital vtx to to dji googles v2, you need to check their manuals for it. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official Thanks for the reply. If I connect my sbus and gnd pins from the adapter board to the rc in port in pixhawk, then I wont be able to connect my radio pin from the telemetry air unit as it will be occupied. So the drone will not connect with the transmitter. Please suggest a method, if it makes sense
@@AyushDoshi-qm3by Hi, sir. You can check the diagram of the PIXHAWK and make the cable by yourself. Here is the link of PIXHAWK. You can check the diagram from the link here: www.radiolink.com/pixhawk Any other question please feel free to contact us.
Hy, can you connect the DJI unit to Pixhawk ? Have you wire it? I speak about pixhawk 2.4.8 , not crossflight!
Yes. You can. When using the DJI VISTA air unit, connect it directly to the digital image transmission port, and modify the following configuration in Mission Planner:
1: Search for SERIALx_PROTOCOL in in Full Parameter List and change the parameters to 33 (DJI FPV). (SERLAIx_PROTOCOL (x represents the serial port number, if inserted in TELEM1, search for SERLAI1_PROTOCOL)
2: Search for OSD_TYPE in Full Parameter List and change the parameter to 3 (MSP).
3: Save and restart flight controller.
Note: If your VISTA has been upgraded to the latest firmware (Firmware version V01.01.0000 and above) to be compatible with DJI G2 glasses, follow the settings of the O3 air unit.
When using the DJI O3 air unit, connect it directly to the digital image transmission port, and modify the following configuration in Mission Planner:
1: Search for SERIALx_PROTOCOL in Full Parameter List and change the parameter to 42(DISPLAYPORT).
2: Search for OSD_TYPE in Full Parameter List and change the parameter to 5 (MPS_DISPLAYPORT).
3: Save and restart flight controller.
When using the Walksnail AVATAR air unit, connect the interface to the last 4 pins of the digital image serial port (12v G TX RX), and modify the following configuration on the Mission Planner:
1: Search for SERIALx_PROTOCOL in Full Parameter List and change the parameter to 42(DISPLAYPORT).
2: Search for OSD_TYPE in Full Parameter List and change the parameter to 5 (MPS_DISPLAYPORT).
3: Save and restart flight controller.
Thank you for your answer! The DJI air O3 unit can be wirede with DJI NAZA M V2 or DJI M lite? I have those two filghtcontrolers, too!@@Radiolink_official
@@vasilealexandru983 Hi, sir. Sorry we are not professional in DJI products. We recommend you to ask for the after-sales of DJI products. If any questions of RadioLink products please feel free to contact us.
@@Radiolink_official Thanks a lot!
@@vasilealexandru983 Our pleasure.
Hey! Can you tell how can i connect caddx vista with this flight controller
Hi, sir. When using the DJI VISTA air unit, connect it directly to the digital image transmission port, and modify the following configuration in Mission Planner:
1: Search for SERIALx_PROTOCOL in in Full Parameter List and change the parameters to 33 (DJI FPV). (SERLAIx_PROTOCOL (x represents the serial port number, if inserted in TELEM1, search for SERLAI1_PROTOCOL)
2: Search for OSD_TYPE in Full Parameter List and change the parameter to 3 (MSP).
3: Save and restart flight controller.
Note: If your VISTA has been upgraded to the latest firmware (Firmware version V01.01.0000 and above) to be compatible with DJI G2 glasses, follow the settings of the O3 air unit.
When using the DJI O3 air unit, connect it directly to the digital image transmission port, and modify the following configuration in Mission Planner:
1: Search for SERIALx_PROTOCOL in Full Parameter List and change the parameter to 42(DISPLAYPORT).
2: Search for OSD_TYPE in Full Parameter List and change the parameter to 5 (MPS_DISPLAYPORT).
3: Save and restart flight controller.
When using the Walksnail AVATAR air unit, connect the interface to the last 4 pins of the digital image serial port (12v G TX RX), and modify the following configuration on the Mission Planner:
1: Search for SERIALx_PROTOCOL in Full Parameter List and change the parameter to 42(DISPLAYPORT).
2: Search for OSD_TYPE in Full Parameter List and change the parameter to 5 (MPS_DISPLAYPORT).
3: Save and restart flight controller.
hey my drones yaw is tilting to left,can you share the correct pid settings of this flight controller
Hi, sir. The PID parameters are different for each plane. You need to adjust the PID settings based on your planes. Here is the detailed manual of crossflight. You can check the methods on how to set parameters. And then you need to adjust PID and test yourself. www.radiolink.com/crossflight_manual If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Help me please i have big problem cross flight controller
Many many issus in controller
Programing
Batter 1 voltage low
Arming
Etc etc please help
Hi, sir. Thank you for your support. Could you please check the detailed manual of CrossFlight? www.radiolink.com/crossflight_manual It introduces details on Battery Monitor Setup. It is in Chapter 5.2.3 Connect the Spare Parts. You may check it. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official love your services
by the way thank you so much
my drone succesfully flying thankyou 😗
@@शकीलअहमद-य1ढ Great to hear that. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
@@Radiolink_official Love From India ❤❤❤❤
Make a video full setup hardware assembly all connection and use memory card
Hi, sir. May I know what flight controller you are using? The video shows how to connect to DJI FPV digital system. You can check the connection diagram in the video to connect them. And for memory card, you just need to plug it into the card holder. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
Can I use some other camera and vtx??
Hi, sir. Yes. You can use other camera and vtx, just make sure they can connect with our flight controller. You can refer to the connection diagram in the tutorial. If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn
I use the Byme- A and Byme-D on almost all of my aircraft even the experimental aircraft. I’m definitely going to try one of these out and possibly make a video review of this. My contact info is on my page if you guys ever want to send me stuff for a review 🥂
Hi, sir. Thank you for your support. Do you mean crossflight flight controller? It is our new flight controller with best price and high quality. Here is the link of it for your reference. www.radiolink.com/crossflight_where_to_buy If any question about RadioLink products please feel free to contact us. Our email is: after_service@radiolink.com.cn