How To Program keyless Entry remote for GM / Chevrolet / GMC 1998-2006
HTML-код
- Опубликовано: 11 фев 2018
- If you would like to leave a donation here is a link ...
www.paypal.com/cgi-bin/webscr... This video will show you how to program a new remote for many Chevrolet, GMC, Pontiac, and Cadillac vehicles.
My affiliated link to this part from amazon
amzn.to/34cznyT
DORMAN #13733
REMOTE PROGRAMMING:
Please make sure to read before attempting.
Any remotes not present at the time of programming will STOP working
- 1. Enter the vehicle, close, and unlock all doors using the power unlock switch on the driver’s door. Insert the key into the ignition but do not turn it yet.
- 2. Using the power unlock switch on the driver’s door, press and hold the switch in the unlock position.
- 3. While holding the switch in the unlock position, switch the key as far ON as it will go without starting the vehicle and back to OFF two (2) times, ending in the OFF position, then release the power unlock switch.
At this point the vehicle door locks should automatically lock and unlock, indicating that the programming mode has been activated.
- 4. Using any remote, press and hold down the “UNLOCK” and “LOCK” buttons simultaneously for 15-30 seconds until the door locks automatically lock and unlock. If 30 seconds pass while holding down the buttons and the vehicle door locks do not cycle, then the remote programming has failed and you must restart the programming from STEP 1.
- 5. Repeat STEP 4 for all remaining remotes you wish to program. You can program up to 4 remotes total.
- 6. Once you have programmed all of your remotes, exit the programming mode by switching the key to the ON position. The vehicle door locks will lock and unlock automatically indicating that the programming mode has been exited. Turn OFF the key and remove it as well as open and close the driver’s door.
- 7. Test all remotes to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1 and switch the order in which you are programming the remotes.
This procedure was carried out on a 2003 CHEVY SILVERADO but will also work for the following vehicles
Cadillac
2003 2004 2005 2006 Escalade
Chevrolet
2003 2004 2005 2006 Avalanche
2005 2006 Equinox
2003 2004 2005 2006 Silverado
2007 Silverado Classic Body Style
2003 2004 2005 2006 Suburban
2003 2004 2005 2006 Tahoe
GMC
2003 2004 2005 2006 Sierra
2003 2004 2005 2006 Yukon
2003 2004 2005 2007 Hummer H2
IF YOU HAVE ANY QUESTIONS JUST ASK!
** If the video was helpful, remember to give it a "thumbs up" and subscribe. **
Follow me on INSTAGRAM
/ falcons_garage
Twitter.
/ falcons_shop
Garage's Facebook
/ falcons-performance-an...
Facebooks Hobbies
/ falconshobbies
My Gaming Channel.
/ @falconsgaming
Disclaimer:
Due to factors beyond the control of Falcons Garage, I cannot guarantee against improper use or unauthorized modifications of this information. Falcons Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in my video. Use this information at your own risk. Falcons Garage recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Falcons Garage, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Falcons Garage 
Авто/Мото
Quick and to the point, but included details that people need. Great video.
Thank you. Simple, straight and to the point.
Thank you for keeping it straight to the point
Thanks bro I was having trouble finding out how to do two remotes. This video explain perfect
I'm glad I could help out!
Thank I was activating for my 07 Tahoe and the original one was desactívated . Thank you man
Glad it helped
Hey man thanks great video and I was about to take this remote back to the store... But you saved the day
Glad I could help!
Great video. Thanks for posting. I like the super dramatic intro music!
lol
Thanks bra! You helped me greatly 👍🏽
Glad to hear it!
Helped alot thank you
Worked perfect, thanks!!
Glad I was able to help.
Thanks man I’m 18 and got my first car (Chevy trailblazer) and this video worked like a charm
Very helpful thanks
Very good instructions
worked🙌🏽🙏🏽did it for co workers truck 🙌🏽👍🏽
Nice 👍
Anyone can tell me how to programme Chevy Cobalt 2006 Ls 2 door key fob.
Hey falcon. I have a 2008 chevy silverado 1500 that i want to reprogram the fob on but on the settings when i want to activate relearn key entry, it will not activate. Any ideas what i can do? Thanks ahead of time
I would really like to know where you bought that key fob for your pickup truck I saw somebody else also featuring the same brand for a Chevy Malibu which is where what I have so the information would be appreciated
the one I got is from doorman, i got it at oreillys ... but also have a link for it on the description
Would this work for Monte Carlo
Will it work on a 99 Chevy monte carlo
My truck has an after market alarm system and the remote still stays connected even after i follow the steps
damn, real cool man!!!!!!!!!!!, thanks
Pokgi-World thanks for watching!
np don't really know a lot about cars
If my old remote don't work what should I do
Will this work if you have an alarm system or are there extra steps..?
Thanks
It probably won’t work. Because the aftermarket alarms use the same system
This way works for 2004 cavalier??
Hello. I am trying to program a brand new replacement key fob for my 2001 Chevy Tahoe. As mentioned the key fob is brand new, with brand new working batteries. I have followed/repeated the entire insert key, hold down unlock button, turn ignition off/on twice, wait for the lock to cycle, press and hold lock/unlock on fob simultaneously. But the lock never cycles therefore the Tahoe never enters programming mode. As a side note, I know that the locks are capable of cycling. Because when I pull and hold the bright light lever while cycling the key twice to program my desired door lock/unlock sequence the locks will actually cycle, the same way that they should when programming the key fobs. Can you please share some troubleshooting steps that might help me diagnose why my Tahoe won't enter programming mode so that I can program my new key fobs? Thank you.
I have same issue.
Me too
I had same issue as you. I had the same looking remote, but it wasn't the right one.
A lost mine and they try to brake in my truck how to desprogram that other one
Our truck doesn't have the original keyfob when we bought it. Do we need the factory keyfob to program the new one or will the new one ne accepted without it?
Same did you figure it out ?
@@JuanGutierrez-bi4zo you dont need the original my 2 new fobs programmed just fine without it
When you cycle do you start the engine?
No.
My chevy don't have power lock button how do I do the keyless remote my chevy is a 06 colorado
if you dont have a "power button" then it dosent have the actuators to unlock it automatically ... you would need an entire kit for that
Our 2005 GMC Canyon won't go into program mode. What am I doing wrong? TY
Would this work on a 07 sierra non electric
probably not.. if they don't have electric locks
hey I have a remote that works, but when i do the new remote the old one does not work. Then vice versa help please.
you have to program both at the same time
Is it possible to program this with the alarm going off?
not sure .. but dont think so
The Chevrolet dealership told me they need $200 to program their $70 remote
Hey would this work on a 2005 equinox
ruclips.net/video/SLSonsbVYL0/видео.html
I have 2000 Chevrolet Silverado I have problem is not enter to programming my control
My 04 chevy malibu maxx lt doesn't beep or unlock the doors when I hold the unlock button and turn the key twice. Any help would be appreciated
Doesn’t that car have a key fob? Like all in one?
Will this work on a 98 lumina lol?
Hello was wondering if you can help me out please I been trying several programs I have a chevy cavalier 03 and I had to drill out my ignition switch cylinder I replaced it with new key every thing all maintenance up to date and starter and relay every good strategy and for to seconds and dies
did you get the new key programmed?
No
Great video, now get some sleep
would this work on a 2008 chevy colorado?
Did it work?
My car does not lock and unlock
Where can you buy the key fob?
link in the description
Question, my power button on my drivers side door doesn't work, is there a way to bypass that step to program new key fobs? I bought key fobs because my old one quit working, and then my door lock on drivers side quit working as well. So I bought new key fobs to bypass getting the door lock fixed. Is there still a way to program the new key fobs?
not as far as I know
@@FalconsGarage thank u, that sucks..... :(
What about the red alarm button how do you program that?
wen you program the control like on the video the ENTIRE controller gets programmed.
@@FalconsGarage Ok that's good to know. Thank you!
i have a 2006 chevy colorado. does this work for it?
I believe that's a different procedure
Do you have any advice for a 2005 Chevy Colorado ?
I tried this method several times, but the doors don't unlock again after cycling.
Thanks
Can I do it on a 2005 Chevy Equinox LT
No I tried and with a little more research I found out we're the unlucky ones that have to go to a locksmith and have the new key programmed.
I actually went to the dealership for 2 key fob $165.00 got the key fob on amazon. But thanks brother
I did this like 200 time lol but it still is not working when I get to the step where u hold the lock and unlock button
most likely there is an issue with your alarm module
I haven't received my replacement fob yet but I wrote this down from his video and others. With doors closed, insert key, hold down unlock button on door, turn key on and off, and on and off. When lock clicks, release unlock button on door. On remote, hold down lock and unlock button together until lock clicks (could be up to 30 seconds), release buttons on remote. To finish, turn key to on, horn should honk and/or lock should click, turn key to off. All done.
esto sirve para una 2005 saturn vue?
not sure
@@FalconsGarage ya pedi los controles y son iguales al que muestras en el video, deja que me lleguen y te digo si funciona. Saludos
eso sirve para el impala 2000-2005?
no exactamente
My remote new remote isn't programming, any suggestions on why?
could be something else wrong with the system
@@FalconsGarage what else could it be?
Man I’ve seen so many videos saying the same thing but my truck won’t automatically unlock after cycling it twice while holding the button 😭😭😭😭
then there might be some internal issues with that system
My car’s a 2013? 😞
Same instructions for 2007 HHR?
the HHR has a flip key/fob I believe .. its not the same
Falcon's Garage, it's just a three button fob.
I bought one on Amazon, but I don't want to mess anything up if I hit the wrong buttons.
Bought the car used & it came with one 🔑 only.. Nothing else.
I guess I'll try anyway??
@@I_just_thrift_my_pants How did this work out for you? Thinking of ordering replacements and trying it. Thanks!!
@@TiaAnders429 I never ended up getting them.....
My key wont cycle from on to off it gets stuck
could be a couple of things
worn out key, if new key could be cut wrong or inside the key cylinder is broken
I get the locks to unlock and lock for program mode but i cant get the remotes to get program
Maybe remote is bad or a bad battery.
Y como le ago para los que no tienen botones
explicamelo un poco mejor
telequinesis
Roberto, si no tienes botones no tienes acuadores. Esto no es para tu coche.
Will this work on Chevy cavalier 04 not trying to be funny sorry guys
Doesn’t work for 2005 Chevy Colorado.
Did you ever find out how?
@@Cletus0525 I have not :( but to be fair I haven’t continued looking after watching this video
Entry music way way way to loud!