God bless your soul you fixed what could have cost me 1-2 weeks of DJI stupid repair service. Thank you for helpful video I'll make sure all my DJI buddies know this video if update ever fails.
Hello, thank you for the video, I made the last update. In fact, I don't use my drone much, and the update went badly. The drone kept ringing. I did a lot of research to find an explanation and it was thanks to your video that I was able to redo the update, thank you very much for your help. Good day
Hey @A Hughes , thanks for your well constructed tutorial. I followed these steps and at the end of the update, I received a solid red light instead of the green light. According to the “install log” the update has failed. Any indication of why this could be?
I ran into a problem I believe was caused by a old/bad SD card. I think the P3 tried to read the card on boot. Ever since that it says no signal/Flight error records. I've tried your reset and I'm not seeing any of the green/amber led on the gimbal. My question is, if I get the audible two quick beep and no LED...does that mean anything? As in your experience. DJI support was not even close to helpful.
hi . i have a phantom 3 4k . yesterday , i was updating the new version of DJI GO and then i didn't totally install ( upgrade) for phantom drone and its controller because i powered off drone after that,. but then, i turned on. nothing requires me to do sth. . so , can you help me out to solve this issue?
Hey, I'm encountering the same exact issue right now. Did you ever figure out what to do? Thank you so much in advance! Help would be greatly appreciated!
+Vigilantes68 Obly if the firmware contains a battery update and you have more than one battery ( just put the other battery in and power on, it will get updated ). After that, NO, there is no need to leave the firmware on the SD..
Hi AHughes, you are my last hope. I have a P3P. And the camera is acting weird. when i turn on the P3P and then record a video the images are blurry. But after i reset the camerasettings the images are fine. Once i turn the bird off and then on again the problem starts all over. Blurry images until i reset the camerasettings. Do you have any idea why that is?? cheers, Mark
![Felix "Unfair" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/Oswujxm2Ag0/mqdefault.jpg)
God bless your soul you fixed what could have cost me 1-2 weeks of DJI stupid repair service. Thank you for helpful video I'll make sure all my DJI buddies know this video if update ever fails.
Thank you so much. I've watched near a hundred videos and I couldn't solve it!
Hello, thank you for the video, I made the last update. In fact, I don't use my drone much, and the update went badly. The drone kept ringing. I did a lot of research to find an explanation and it was thanks to your video that I was able to redo the update, thank you very much for your help. Good day
Andy thanks for the visual demo. This is very helpful.
Thanks man!!! your awesome. Ive been bashing my head against the wall all day trying to sort it
Hey @A Hughes , thanks for your well constructed tutorial. I followed these steps and at the end of the update, I received a solid red light instead of the green light. According to the “install log” the update has failed. Any indication of why this could be?
does we need a sd carn on it while doing this? with the firmware we want? can we do it without? does it need to be empty?
Thank you very much! This helped a lot and fixed my bug
Hi, i did exactly this (about 6 times) and my drone's updates always seem to fail
It seems that smebody else have same problem that i have. Did you solve it and if do, how?
Emil Väisänen I can’t solve it still to this day did you ever solve it.
I ran into a problem I believe was caused by a old/bad SD card. I think the P3 tried to read the card on boot. Ever since that it says no signal/Flight error records. I've tried your reset and I'm not seeing any of the green/amber led on the gimbal.
My question is, if I get the audible two quick beep and no LED...does that mean anything? As in your experience. DJI support was not even close to helpful.
Thanks, Andy Hughes
Does it applies to phantom 3 standard cos am having issues with the sound that wont seen to go away
I'm trying to put P3X_FW_V01.11.0020.bin on but 3/4 through it goes red and txt files says corrupted. I give up ! I'll sell it for scrap on ebay
hi . i have a phantom 3 4k . yesterday , i was updating the new version of DJI GO and then i didn't totally install ( upgrade) for phantom drone and its controller because i powered off drone after that,. but then, i turned on. nothing requires me to do sth. . so , can you help me out to solve this issue?
Hey, I'm encountering the same exact issue right now. Did you ever figure out what to do? Thank you so much in advance! Help would be greatly appreciated!
Thank you thank you!!!!! This helped a lot
mine doesn't even have that button.
how to cancel the installtion mode.I did this one time.now it always boot like this. without sd card ,it will stop at the single beep.
How to do it on a phantom 3 standard?
Do you have to leave the same firmware on the SD card?
+Vigilantes68 Obly if the firmware contains a battery update and you have more than one battery ( just put the other battery in and power on, it will get updated ). After that, NO, there is no need to leave the firmware on the SD..
+Andy Hughes Cool!, just got a spare 4K camera and needed to be updated to what my firmware is on the aircraft. Thank you for showing this.
it didnt work 4 me edither when its done it starts off green then turn red can someone help me plz
is it possible downgrade from 1.11 to 1.8?
Did you manage to downgrade
How hard reset phantom 3 standard controller
Does my remote need to be on?
Y en el standard?
Hi AHughes, you are my last hope. I have a P3P. And the camera is acting
weird. when i turn on the P3P and then record a video the images are
blurry. But after i reset the camerasettings the images are fine. Once i
turn the bird off and then on again the problem starts all over. Blurry
images until i reset the camerasettings. Do you have any idea why that
is?? cheers, Mark
Hallo, si it possibile downgrade from 1.6 to 1.4?
guerino maione ‘
I did the same as the video and it does not work.
The back LEDs are flashing green
The led forward is always red.
Same
FRackking DJI.... I'm ready to smash mine... good info
A
Thanx alot...
Good😀😀😀
Do you have to leave the same firmware on the sd card?