When I see a video with such a title, for some funny reason I expect to see the problem resolved. Not spend 21:13mins being shown the problem that I already have. What does this achieve?
"Yippee ki-yay" :-) It works. I had a crash with my P3A, the gimbal ribbon cable busted. I bought a cheap gimbal ribbon from ebay. I had same problem like in this video. Than I bought an original cable from DJI, replaced and it works.
Данияр, здравствуйте. Вы не сталкивались с проблемой, когда Р3А не прошивается. Всё делаю по инструкции, но подвес не издаёт сигналов звуковых, световой индикатор не загорается ни красным, не зелёным. более того, когда включен дрон, индикатор тоже не светится. + на экране приложение высвечивается NO IMAGE TRANSMISSION и в настройках вижу, что GIMBAL DISCONNECTED,
DJI GO thinks your Phantom is An Inspire - Camera View is not available for the Phantom A simple Scottish Bloke ha the answer for you all. Make sure the DJI Go App is not open just now (just close it as you normally would for now) 1. Power up your Phantom. 2. Plug in your Phone to your charger and set to “Transfer files / Android Auto” (not “Charge Only”) 3. Plug in your Micro USB or Micro USBC to your Phone/Tablet 4. plug the USBA (the large end to the Remote Control - (RC) - Don’t use the Micro USBC on the RC) 5. Power up the RC (Remote Control) 6. your phone will ask "charge Only? - Set to “Transfer files / Android Auto” (not “Charge Only”) 7. Launch DJI GO and Presto! - you have “Camera'' with your phantom 3 on-screen (not “How to Connect” 8. Select Camera and you no longer need to fly blind. All the best dudes - I can certainly now fly again as can about 6 of the folks I asked to try this out and they can too. Drop a post if it works - would be good, Yours hopefully... SXB (Stu)
Hello there.... The sound the gimbal makes at 12:58 during the software update indicates that the gimbal is defect...so... If you stille have warranty...i suggest you bring the drone back where you bought it and let them fix it or you can go to the DJI website ...click support and then Repair Services... Then follow the instructions... Good luck 👍
Тоже проблема с видео, фотки делает а картинки на планшете нет. После покупки дома проверял, видео с камеры на планшете было. Взял через два месяца на природу и такая проблема. Подскажите что может быть ведь Коптер не падал все это время стоял на полке.
saludos tengo el mismo problema, trato de instalar el firmware desde 1.2 hasta la 1.9 y nada que se arregla... y es mas si vuelvo a instalar la misma se daña al principio, alguien sabe como hacer regresar de fabrica el phantom asi como se puede hacer con el RC, pero todo paso por actualizar a una nueva version, espero una ayuda saludos
formatea la memoria a profundidad. vuelve a realizar la actualización , si no funciona se ha dañado la board de la cámara. Me pasó con el Inspire 1 .Hay que cambiar toda la placa.
Not being able to see the camera button for the Phantom 3s (it is only available for the Inspire. Most Mobiles or Tablets (when plugging in to charge ) display 'Charge Only' on the mobile/tablet screen - It has been an issue since 2016 and unsure if anyone has found the solution. The camera button only appears against the Inspire and not the Phantom. Hopefully I have solved this. 6 of my friends have tried this successfully . It costs nothing and takes about 25 seconds (if that!). Rather than 100 lines of explanation about firmware, controllers (GL300 A, B or C), re-linking, re-setting the RC and drone firmware, new phones/tablets, cables adapters etc. - here's the solution. From a simple Scottish Bloke who never gives up! OK - don't launch the Go App just yet... 1. Power on your Phantom 2. Plug in your Phone to your charger and when it says on screen 'charge only' select 'data transfer' instead 3. Plug in the Micro USB or USBC plug (the small one) of your charging cable to your Phone/Tablet 4. plug in the USBA plug (the wide one) to the wide USB connection at the back of the Remote Control 5. Power up the Remote Control 6. your phone may again ask "charge Only? 7. Change option to "data transfer" 8. Launch DJI GO and Presto - you have 'Camera'' with your phantom 3 on screen - Inspire might also have the camera function enabled but your Phantom will will be good to go. I hope this works for everyone!!!! If you have problems linking your RC and Drone I can help - Just leave a post. Drop a post if it works - would be good to see if this works for all - Enjoy Droning on! Yours hopefully... SXB (Stu) If any of this isn't clear - I can post some pics
@@stuartxblack братка выложи фотки плиз, блять для меня это тёмный лес, фантом 3 про, пиздец лежал без полёта 4 года . Т. К был такой же второй на котором летал. Подарил свой , открыл новый спустя 4 года, в плёнке все дела,девственник - все работает, крутится. Но нет передачи картинки на смартфон в реальном времени .
@@megogo291 don't worry, I fixed the issue with the same outdated phone and also an incompatible controller. It's all about trial and error with flight and rc firmware and also your phone dev settings. I'm sure others will figure it out too. I'm not good at editing videos, would be pointless trying to explain it. Working now tho.
Hi I use Google translation I have the solution to this problem Only yesterday, I managed to correct it After two or three days I put a clip to explain The way
I'm talking about the problems that happen after updating the Duron plane or updating the Controlrol Riomot The problem is not related to the cable or anything in the hardware I hope you can wait I gather the sector and asked a friend to record the sound in English
Alguien tiene la solución? a mi me pasa exactamente lo mismo, lo único que he hecho es no utilizar el don durante un par de meses, cuando lo guardé funcionaba perfectamente y al pasar un tiempo sin volarlo me da ese problema, lo intenté actualizar y me pasa lo mismo que el video, sale error.
CARLOS ARTURO ARBELAEZ CANO mira yo compré en un store de acá en Argentina un Phantom para desguace, abrí el gimbal y remplaze directamente la placa, sacas los conectores pones la nueva, reconfigurar el gimbal con la app y salió andando, la placa no viene suelta, viene el gimbal completo, lo que yo hice fue para ahorrar dinero
its the GMCB. gimbal main circuit board. cant find new one. should buy a crashed gimbal from someone and replace it. i did fix 4 same issue dude. ask me about it, cost me alot of work and money until i discovered the prob. goodluck
+Seamless Roofs bro u should hav to search and aak for a crash drone. i hav one for spare coz i fix them. but am sure that am too far. goodluck in finding one.
Отправил официалам вот что они сказали: Результат диагностики: В результате проведения диагностики обнаружено : Выход из строя модуля памяти NAND центральной платы подвеса - ремонт невозможен,требуется замена подвеса, данная неисправность проявляется при долгом пролеживании квадрокоптера без включений.
+Егор Гаврилович что интересно всё работает, камера снимает 4к видео, только одно не показывает картинку на смарте, засада... я не проверил работает или нет, взял приехал с америки принес подарить брату, и тут этот косяк, они там не понимают что зимой люди не летают, как минимум 3 месяца о коптере все забывают, какого лешего я должен его заряжать каждый месяц, китайцы... зла на них не хватает...
How many mistakes can you make while trying to fix a probleam ? .....Well here is the anwser to nothing in this very long video , terrible! Worst ever!
When I see a video with such a title, for some funny reason I expect to see the problem resolved. Not spend 21:13mins being shown the problem that I already have. What does this achieve?
"Yippee ki-yay" :-) It works.
I had a crash with my P3A, the gimbal ribbon cable busted. I bought a cheap gimbal ribbon from ebay. I had same problem like in this video. Than I bought an original cable from DJI, replaced and it works.
Please Which cable you are talking abut, where is that located? because I have the same problem. Thanks
Данияр, здравствуйте. Вы не сталкивались с проблемой, когда Р3А не прошивается. Всё делаю по инструкции, но подвес не издаёт сигналов звуковых, световой индикатор не загорается ни красным, не зелёным. более того, когда включен дрон, индикатор тоже не светится. + на экране приложение высвечивается NO IMAGE TRANSMISSION и в настройках вижу, что GIMBAL DISCONNECTED,
DJI GO thinks your Phantom is An Inspire - Camera View is not available for the Phantom
A simple Scottish Bloke ha the answer for you all.
Make sure the DJI Go App is not open just now (just close it as you normally would for now)
1. Power up your Phantom.
2. Plug in your Phone to your charger and set
to “Transfer files / Android Auto” (not “Charge Only”)
3. Plug in your Micro USB or Micro USBC to your Phone/Tablet
4. plug the USBA (the large end to the Remote
Control - (RC) - Don’t use the Micro USBC on the RC)
5. Power up the RC (Remote Control)
6. your phone will ask "charge Only? - Set to
“Transfer files / Android Auto” (not “Charge Only”)
7. Launch DJI GO and Presto! - you have “Camera''
with your phantom 3 on-screen (not “How to Connect”
8. Select Camera and you no longer need to fly blind.
All the best dudes - I can certainly now fly again as can about 6 of the folks I asked to try this out and they can too.
Drop a post if it works - would be good,
Yours hopefully...
SXB (Stu)
My light doesn’t even turn on. Can that just be a bad gimbal assembly ?
Hello there....
The sound the gimbal makes at 12:58 during the software update indicates that the gimbal is defect...so...
If you stille have warranty...i suggest you bring the drone back where you bought it and let them fix it or you can go to the DJI website ...click support and then Repair Services...
Then follow the instructions...
Good luck 👍
El problema es de la board de cámara. Me pasó lo mismo con un Inspire 1 hay que cambiarla.
y como hago eso
@@MotorStyle cambiando la board del gimbal
Having same problem
Tienes que sincronizar de nuevo el control al phantom y se soluciona
Тоже проблема с видео, фотки делает а картинки на планшете нет. После покупки дома проверял, видео с камеры на планшете было. Взял через два месяца на природу и такая проблема. Подскажите что может быть ведь Коптер не падал все это время стоял на полке.
Tengo un problema con la cámara en modo fotografía se ve perfecto pero en modo vídeo salen líneas en el vídeo
Hi, can anyone advise how to fix "No Image Transmission Signal" issue on P3Pro?
Buy a new one. I fixed this way.
all i had to do was update the firmware, then restart the software and reconnect
I bought two, so just in case one of them breaks.
pull out memory card turn p3 on without sd card in you should get picture connection then put the sd card back in
@@davidcarpetlayer8390 thanks man, i Google a lot until i find your comment and its fine again🤙🙌👏💪📷🌊
saludos tengo el mismo problema, trato de instalar el firmware desde 1.2 hasta la 1.9 y nada que se arregla... y es mas si vuelvo a instalar la misma se daña al principio, alguien sabe como hacer regresar de fabrica el phantom asi como se puede hacer con el RC, pero todo paso por actualizar a una nueva version, espero una ayuda saludos
formatea la memoria a profundidad. vuelve a realizar la actualización , si no funciona se ha dañado la board de la cámara. Me pasó con el Inspire 1 .Hay que cambiar toda la placa.
ha podido solucionarlo, en este momento tengo el mismo problema, no signal y no actualiza las firmware que trato instalarle
no se soluciono... estoy esperando alguna soluciuon de dji pero me dijeron que hay que cambiar el cardan de la camara, no lo e hecho
hermano yo le aseguro que es problema de la board . por experiencia propia . debes cambiar toda la cámara completa .
yo hice eso y no funciono es el flex o el board dela camara fijo algo mayor a eso es el drone
I have the same problem ! How u fix it?
Buy a new one
For myself, I switch from the camera mode to video mode and back and then camera will display.
@@SomethingBlack what?? Switched from camera mode to video mode? Where gives this option? ? Thanks
How do you fix this? It doesn't show how to fix it.
Software update
Allô, Can you help us with version of french please
Reflow ambarella processor from gimbal module, this can solve issue
???
No image signal transmission ! DJI Phantom 3 Pro.
Not being able to see the camera button for the Phantom 3s (it is only available for the Inspire.
Most Mobiles or Tablets (when plugging in to charge ) display 'Charge Only' on the mobile/tablet screen - It has been an issue since 2016 and unsure if anyone has found the solution.
The camera button only appears against the Inspire and not the Phantom. Hopefully I have solved this. 6 of my friends have tried this successfully
.
It costs nothing and takes about 25 seconds (if that!).
Rather than 100 lines of explanation about firmware, controllers (GL300 A, B or C), re-linking, re-setting the RC and drone firmware, new phones/tablets, cables adapters etc. - here's the solution.
From a simple Scottish Bloke who never gives up!
OK - don't launch the Go App just yet...
1. Power on your Phantom
2. Plug in your Phone to your charger and when it says on screen 'charge only' select 'data transfer' instead
3. Plug in the Micro USB or USBC plug (the small one) of your charging cable to your Phone/Tablet
4. plug in the USBA plug (the wide one) to the wide USB connection at the back of the Remote Control
5. Power up the Remote Control
6. your phone may again ask "charge Only?
7. Change option to "data transfer"
8. Launch DJI GO and Presto - you have 'Camera'' with your phantom 3 on screen - Inspire might also have the camera function enabled but your Phantom will will be good to go.
I hope this works for everyone!!!!
If you have problems linking your RC and Drone I can help - Just leave a post.
Drop a post if it works - would be good to see if this works for all - Enjoy Droning on!
Yours hopefully...
SXB (Stu)
If any of this isn't clear - I can post some pics
@@stuartxblack братка выложи фотки плиз, блять для меня это тёмный лес, фантом 3 про, пиздец лежал без полёта 4 года . Т. К был такой же второй на котором летал. Подарил свой , открыл новый спустя 4 года, в плёнке все дела,девственник - все работает, крутится. Но нет передачи картинки на смартфон в реальном времени .
@@megogo291 don't worry, I fixed the issue with the same outdated phone and also an incompatible controller. It's all about trial and error with flight and rc firmware and also your phone dev settings.
I'm sure others will figure it out too. I'm not good at editing videos, would be pointless trying to explain it. Working now tho.
No video signal? Your drone is not broken, its fault of dji application !
Tengo el mismo problema y nada 😔
Где скачать файл прошивки?
C'est ça mon problème 🤔🤔🤔
Hi
I use Google translation
I have the solution to this problem
Only yesterday, I managed to correct it
After two or three days I put a clip to explain
The way
can u explain pls
I'm talking about the problems that happen after updating the Duron plane or updating the Controlrol Riomot
The problem is not related to the cable or anything in the hardware
I hope you can wait I gather the sector and asked a friend to record the sound in English
Can you make a video, just show the steps to fix it.
And what was the problem? Google didn't find the same problem we had. Thanks
Terrible video but the comments helped. I restarted my cell and video was restored...thank Jesus
What do you mean restarted cell
You didn't show how you solved the problem not a good video im afraid
alguien depronto encontró solución a este problema?
Alguien tiene la solución? a mi me pasa exactamente lo mismo, lo único que he hecho es no utilizar el don durante un par de meses, cuando lo guardé funcionaba perfectamente y al pasar un tiempo sin volarlo me da ese problema, lo intenté actualizar y me pasa lo mismo que el video, sale error.
Encontro la solucion?
@@laproduprofe hace mas de 4 años de eso, ya tiré el drone ese jejej
@@laproduprofe how to fix it ?
كيف تدوير الكاميرا الى اليمين واليسار
Xin huong dan khoi phuc loi cam on
si es la placa de la cámara la cambie y volvió todo a la normalidad, ahora tengo miedo de actualizar
me explicas qué es que cambiaste la placa o que signific esa operación. Gracias
CARLOS ARTURO ARBELAEZ CANO mira yo compré en un store de acá en Argentina un Phantom para desguace, abrí el gimbal y remplaze directamente la placa, sacas los conectores pones la nueva, reconfigurar el gimbal con la app y salió andando, la placa no viene suelta, viene el gimbal completo, lo que yo hice fue para ahorrar dinero
Mariano Avila Ok. Mariano. Estoy tomando nota y te agrezco por la orientación. Seguiremos en contacto.
Mariano Avila la actualizacion hay que hacerla de forma perfecta. De lo contrario el phantom se bloqueara.
Por fabor donde puedo comprar esa placa? Me puedes pasar el link por fabor.
Народ как откатить прошивки на фантом 3 про
el mismo problema tengo yo. es exactamente igual lo que me pasa. si encuentras algo amigo de como solucionarlo no olvides en pasar la voz :)
pudiste solucionar? yo tengo ese problema en este momento y aun no puedo solucionar
No mi amigo sigo con el gran problema
+HJFilms puede ser una actualización, el flex del gimbal o la tarjeta del gimbal. ahí esta el problema.
Amigos el problema es del cable por dentro él flexible pero no sé dónde comprar el cable
x ebay venden el juego de cables en un paquetico
its the GMCB. gimbal main circuit board. cant find new one. should buy a crashed gimbal from someone and replace it. i did fix 4 same issue dude. ask me about it, cost me alot of work and money until i discovered the prob. goodluck
any way to purchase a main board?
+Seamless Roofs bro u should hav to search and aak for a crash drone. i hav one for spare coz i fix them. but am sure that am too far. goodluck in finding one.
+زاهر صالح Wa7sh how
How much to send it to Wisconsin?
bro am middle east. lebanon its way far from u. i bought a crashed gimbal with 100$ just for this board.
Your response is smarter than everyone else, I can tell you are smarter than everyone else. Thanks best regards
I had the same problem get a new gimbal to fix your problem
Amigo te pasa lo mismo que a mí es el cable por dentro está roto y no se donde encontrarlo
cara memperbaiki ini bagaimana ?
Проблему значит не решили
Its usb port blocked from app so u have to send it to DJI.
nada todavía, trate de hacer todo lo que encontraba en la web pero nada funciona
as encontrado solucion
alguien encontro alguna solucion
tatiana alborta Es la board de la camara con seguridad . Yo la vendo .
GUYS IS THE CABLE THAT CONNECTS THE GIMBAL!!!! IT HAS TO BE VERY WELL CONNECTED
that is what i thought was happening, i crashed my drone twice
But gimbal work perfect, the video doesn't transfer .
hola a mi me sucede exactamente lo mismo , y no encuentro solucion
pudistes solucionar tu problema? yo actualice la APP, el drone y el control y dejo de transmitir imagen.. me sale error y perdi la imagen
hola tube que cambiar una pieza de arriba de la camara
que piesas puedes compartir el nombre please
@@marcelomorales3710 que solucion encontro?
How to fix phantom 3 pro. no signal from camera in fligth ? the image screen frozeen i i cant do nothing!!!
Thanks
Отправил официалам вот что они сказали: Результат диагностики:
В результате проведения диагностики обнаружено :
Выход из строя модуля памяти NAND центральной платы подвеса - ремонт невозможен,требуется замена подвеса, данная неисправность проявляется при долгом пролеживании квадрокоптера без включений.
стикает флешка
и что теперь? они просят деньги за новую плату или брак ихний? У меня тоже коптер простоял пол года и сейчас у меня тоже такая ошибка как у тебя
Если гарантийный срок не истек, то заменят по гарантии. А если истек, то замена подвеса в моем случае обошлась бы в 35к (зависит от модели).
+Егор Гаврилович
что интересно всё работает, камера снимает 4к видео, только одно не показывает картинку на смарте, засада... я не проверил работает или нет, взял приехал с америки принес подарить брату, и тут этот косяк, они там не понимают что зимой люди не летают, как минимум 3 месяца о коптере все забывают, какого лешего я должен его заряжать каждый месяц, китайцы... зла на них не хватает...
Еще как вариант, приемник проверь - стоит НАД платой сонаров
cHANGE Flexible Gimbal Flat Ribbon Cable
Cássio Ávila I’m having a similar issue could you help me out ?
Bullshit
THX my friend
diganme si encontraron alguna forma de resolverlo, me pasó exactamente lo mismo
no has encontrado nada? lo acabo de actualizar hace 5 hrs y me sale lo mismo y aun no lo eh podido solucionar
desde que actualice me sucede este error! me arrepiento de haber actualizado!!!
Alguien encontró sulución?
Эксперты))
How many mistakes can you make while trying to fix a probleam ? .....Well here is the anwser to nothing in this very long video , terrible! Worst ever!
la solucion es cambiar la board de la camara . Yo tengo una nueva para vender.
cual board me puedes ayudar o vender please
everythinone everythinone debes de cambiar la placa que esta arriba de la camara, es decir la placa board.
Me pasó lo mismo y fue la placa ya que no me da imagen y no actualiza se queda en lo último ya no pasa de allí éxitos
prodotto fantastico, ma dall'ultimo aggiornamento è diventato un cesso cinese.
gentaglia
Ну и что это было?/)))
JUST DELETE THE DJI GO APP AND RELOAD.... VIDEO BACK AGAIN . SIMPLE.! :)
BarracudaHawk don’t work
No that's not right, we tried on several phones and tablet, I thought you know the problem.
Or you can just restart your phone. That's what I did.
Apagar y prender?