Видео

"Um" ? From Umbridge? 😅

Do you know the size of the cap wrench you used for the hydraulic filter?

Thanks for this man, I'm building a 93 Sporty and it seems we have very similar ideas, so it's great to see someone doing what I need to see. Thank you.

I just bought a 738 new with auto coupler. Mower rattles and makes noises. I think it's the part that holds the coupler in place. Does your mower deck rattle?

what brand wheel hub bearing assembly did you use and how have they been working for you??? Any issues?

Appreciate the video! I am doing a similar job and got a set without helper springs so this answered my question on swapping them over.

Once that obnoxious music started I was done. See ya!

The music change from teardown to rebuild is great 😂 😊

I got one of these, does pretty well but too easily stops if you use too much pressure.

What is that bar you had to take off

Nice

Sweet lookin truck. I don't like red paint on trucks but this looks good. A good darker shade of red.. 💪😎

jost found the video, good review. by the way, that bobber looks awesome.

I'm 400 miles away from home pulling a 20ft trailer with 4 atvs on it and my truck just started doing this. Thanks for the info

Hi! I want instal this Dynatec 2000i on my Evo 1987 and I have 5 Ohms Dyna Coil. Can I Connect it with this Coil ?? Thank You

I have the same control arms on mine. 😎

How long was your replacement bolts for the foot peg my bike came with new forward controls but the holes on the primary are empty and I need the bolts

Which way should I turn wrench to put back in two wheel drive?

was doing this today and got to about the positive starter cable? is it a 15mm? it’s suck a damn pain and i don’t wanna round it off

Going to do this to my 2012, but i am going to coat with raptor liner, front and back.

PS: you DO know that you can purchase new keystone bars that are internal wiring ready for like $80 bucks right? That way you won't sheer off the casings and ground out your wires after fishing them through a drill hole. But hey whatta I know, only been working on hogs for 31yrs

Ok sweet so you've essentially told us nothing about how to do this ourselves👍👍👌

Have you seen the bank's differential cover for the rear? I have it on my truck and I'm really happy with it but he does a lot of fluid dynamics videos on why not to run the flatbacks.

Use a sewn yellow buffing wheel with brown tripoli.Then sewn cotton flannel wheel with white compound. I sand with 320 then 500 grit before buffing. Mirror finish.

Been fighting my 2500 for a year, 3 shift motors. Finally got it. Connectors were dirty on wire harness side of the plug. Took a little round brush and cleaner to remove. Put old actuator on, works.

I bought mine used for 140 bucks, I got a fairly heavy bike but it's holding it up pretty good with the retainer bar keeping the weight off the jack, im pretty happy with it because it's actually almost brand new, but harbor freight has jacked the price up a bit from what it used to be so I'd have to really think hard about paying what their asking for one these days with the economy in the tank because of you know who.

bro you really need to really show the ride height and not you're face all the time

Very informative, Thank you!

Hello if you have a voes but you want to disconnect it you need to put the switch 1 in position Off ? It s correct ? Can that help if you have a kickstart ? The bike have kick and electric start is a shovel? Thanks for your answer

Do you think this can polish a kirby?

I love mine. Had it for about 7 years now. $199.99, best deal ever.

Awesome video friend! At 100 some hours with no trans oil I would of had second thoughts on buying so hope you got lucky. There is a fuel pressure relief screw to vent before changing the fuel filter. You definitely took the fear of doing this job out! Thanks

Good stuff, much prefer Dynamic timing instead of using the LED. Would be more accurate to achieve 28 degrees as well.

Just got 8” model, actually made by VEVOR, instructions show the spacer mounted inboard between body and behind inner flange: Only the outer flange and retainer nut on the outside😵‍💫

Man when doin that job u replace hub bearing

What's that filler you're using?

I had the same experience with the supplied wheels. They continued to throw material as long as I could stand it. Replace!!!!

9:27 those terminal protectors keep the leaking acid from coming in contact with the terminals. The terminals post although sealed, do leak some acid and vapors out of them and thats why your posts and terminals get the build up.

I see the hydro filter doesn’t come with the home maintenance kit, do you know what the correct part number is? Also, what’s the gap and torque specs on the spark plugs? Thanks for the great video!

Dude your bottom studs are upside down. 😢

i just picked up the same car for 750$ !! super happy

Can the front and back wheels be turned while on it (washing white walls)?

Help me out I can’t get the plug off and I don’t understand how to get it off

My favorite part is replacing the pads because the pads they have right next to it don't fit.

Late to the game but this is quickly becoming one my favorite build series.

T40 is the size??

Hey, at 13:40 did you swap the push rods around?

Yeah I had the same problem with mine and I took and took the die grinder and ground two flats 180° apart from each other and use the 9 sixteenths wrench on the flats work just fine and if you wanna different wheels I would go to empire abrasives and get some wheels very good quality

Tdi swap it

My 08 Dodge Ram keeps blinking 4wd low while in 2wd and then eventually serv 4wd pops up. When I change my actuator do I need to have the truck in 4wd low then?