Thank you Jake. it's always nice to show the rundown, I know you just change the timer! truly thanks for covering the test paradigm! It's nice as it explains the sequence of operations for best understanding Peace..
Salamat sa video Sir Jake, paulit-ulit kung pinapanood iyung video para hanggang sa matotonan ko ito. REE & RME no experience sa pagbabarko sa ngayun. gawa ka po video nang paano ang tamang pagbasa nang diagram na pinakamahirap na diagram sa barko. salamat po uli. Godbless at ingat po
I am a fourth engineer and by watching this video I have got some ideas about how to read these circuit diagrams. Thank you very much for such an informative and a descriptive video. 🙏👍
Thanks a lot for making such practical informative videos. Could you please help me in explaining the procedure for simulating ( manipulating) preferential trip setting in PMS. Due to the lack of awareness, we do not carry out this test. Offcourse, I understand that it may vary from different maker of PMS system, however, we will get some idea about it. Thanks a lot
Since you measured the contacts A1 and A2 of the 57X1 contactor and did not get the voltage, it meant that the timer was not working as it did not activate the 57T1 contacts. Does it mean that you did not reset the fault while troubleshooting?
Sana sir mag tagalog kn pra naipapaliwanag mo ng maayos kc s totoo lng nhihirapan ako s mga sinasabi mo...pero i salute you for being insperation for the new electrician..many thanks God Bless
hi. when you lower the load of the generator. how is that happen ?do you lowering the speed or what .what i see that all generators are connected to one main bus so all generators will work on same load
Sir,I ' m just a beginner and confusing about measuring contact 9 and A1 .It gets no voltage and thought the 57X1 is in close contact .It means The timer is working and 9 & 11 is in close contact also. But I know it' s wrong😅 . Sir could U explain the right ,plz .may be my lack of knowledge.
Hi jake...good afternoon.. Can you help me... My ACB Suddenly turn off, the Reverse power trip alarm indicator lights up... What is the Cause... Thanks jake... 🙏🙏🙏
depends on the set up of your switchboard, there are some which can synch but most of the common set up the emergency generator is really isolated from the aux gen
Mr. lecky do not give people wrong explanation regarding preferential trip functionality target point. Please check it what is actual point for that protecting.
You are doing well your job. That is good to continue to give your knowledge and help an others. I just give remark. Because you say preferential trip is use also because bus bar can not be accommodate such load in case over current is occurred. Actually only preferential trip is used to cut the power for non essential consumers 1 st, 2nd and 3rd group accordingly. That is all why use preferential trip to avoid to trip air circuit breaker (avoid black out). BUS bar is so strong and can be withstand any extremal loads ( wich is not requires any protection) will not affect any load to damage it.
Thank you for this video.. this type of step by step fault finding and drawing is what make you the best.. easy to understand.. well done lecky..
thank you for watching
Please make video on circuit diagram reading
Thank you Jake. it's always nice to show the rundown, I know you just change the timer! truly thanks for covering the test paradigm! It's nice as it explains the sequence of operations for best understanding Peace..
Sir thanks sa nga share na video kahit Hindi Kami nakapag barko natutu din Kami sa troubleshooting nyo God bless
astig ka talaga ka lecky...thanks sa mga good technigues in troubleshooting...God bless..
Salamat sa video Sir Jake, paulit-ulit kung pinapanood iyung video para hanggang sa matotonan ko ito. REE & RME no experience sa pagbabarko sa ngayun. gawa ka po video nang paano ang tamang pagbasa nang diagram na pinakamahirap na diagram sa barko. salamat po uli. Godbless at ingat po
Sir i am also in Maersk line about to go as ETO for first time...and you are my inspiration thank you for explaining in details
I am a fourth engineer and by watching this video I have got some ideas about how to read these circuit diagrams.
Thank you very much for such an informative and a descriptive video. 🙏👍
thank you for your support
Aloha Lecky Jake proud to be an Electrician in foreign flag before like you , always watch insights videos of you. god bless
The best teacher. Salute
thank you
And now you are my idol sir. 🎉🎉🎉🎉🎉
Thank you for making such an informative and useful video
It is really interesting. Keep it up...
Thank you sir, it's a big help for me as an electrician. Keep vlogging sir and Godbless.
Very nice sir thanks for sharing such good practical knowledge
Thanks for your sharing
thank you for watching
Nice review.thanks for your sharing
Very cool, enjoy your posts
thank you so much sir Lecky, from Viet Nam with love
Thanks for the video,very helpful sir
good to see your videos brother.✌👍👍👍👍👍
thank you
I'm currently doing my finals for my ETO certificate, your videos has helped me a lot, keep it up!
Ohh that's nice to know. Thank you for watching
@leckyjake sir, as fresher how to understand which components or terminals are in which areas. Please explain
Very informative videos thankyou for providing such useful information
❤
Useful guide! Thanks a lot!
Thanks for your videos. All of them are very useful. Pls make a video how to test EDG overspeed trip.
I wish you success in your work
thank you very much
Thank u for showing this video. Can u tell how can we do under/over voltage trip
I just love your videos !
You are the best keep going...
Nice explanation brother.. Very useful.. Thank you.
thank you for the knowledge sir jake
Thank you very much, may God help you 🙏
Good 👍
Thank you sir Jake ... I learned a lot on your videos❤️
Thanks u .
I'm fr Myanmar.
Good day sir, hope you doing well.. can I suggest for your next vlog how to read electrical diagram.. thanks
you can oftentimes see the reading of wiring diagrams on my troubleshooting video.
Thanks a lot for making such practical informative videos. Could you please help me in explaining the procedure for simulating ( manipulating) preferential trip setting in PMS. Due to the lack of awareness, we do not carry out this test. Offcourse, I understand that it may vary from different maker of PMS system, however, we will get some idea about it. Thanks a lot
Keep with the good work brother, and let us know should you need our support!
Since you measured the contacts A1 and A2 of the 57X1 contactor and did not get the voltage, it meant that the timer was not working as it did not activate the 57T1 contacts. Does it mean that you did not reset the fault while troubleshooting?
yup, i think I've mentioned that one in the video
@@leckyjake thank you for the vids! Keep doing it, sir! Very knowledgeable! Love it
Hi Lecky, please make a video about the Boilers
Thanks a lot
Please do a video of electrical mooring winch trouble shooting
Keep up the good work :)
Thanks 🙏🙏🙏🙏🙏🙏
Thank you sir👏🏻
can you upload a video on procedure for insulation testing ?
Thank you
Sana sir mag tagalog kn pra naipapaliwanag mo ng maayos kc s totoo lng nhihirapan ako s mga sinasabi mo...pero i salute you for being insperation for the new electrician..many thanks God Bless
we like these videos!!!....shouldnt the second timer have picked up and tripped the breaker?
thanks for watching, we just manipulated the overloading just on the limit that the 1st trip will activate.
hi. when you lower the load of the generator. how is that happen ?do you lowering the speed or what .what i see that all generators are connected to one main bus so all generators will work on same load
Thank sir fir this video
In this state the generator become motor because take power not generation
Did you take the defective timer apart to see why it failed?
thanks👍
At the end you measured the contact 9 to A1? You put the red cable for instance on 9 and the black one on A2? Why A2 and not A1?
Because both are just the same cable, if you are convinient with A1 and A2 then there is no difference
Sir Lecky Jake, in case no available spare timer on board. What is the remedy to solve the problem. Thank you.
Sir,I ' m just a beginner and confusing about measuring contact 9 and A1 .It gets no voltage and thought the 57X1 is in close contact .It means The timer is working and 9 & 11 is in close contact also. But I know it' s wrong😅 . Sir could U explain the right ,plz .may be my lack of knowledge.
how did you activate the preferential trip?
Mr. Secretary present!🖐
😁😁😁
PLC tutorial please 🙏 💕 ☺
sir when to do the testing,once a month or a week?
Can we have your videos on how check high and low frequency and high and low voltage at MSB pls
Hi jake...good afternoon..
Can you help me... My ACB Suddenly turn off, the Reverse power trip alarm indicator lights up... What is the Cause...
Thanks jake... 🙏🙏🙏
is it possible to synchronise Auxiliary Generator and emergency generator together? If not why?
depends on the set up of your switchboard, there are some which can synch but most of the common set up the emergency generator is really isolated from the aux gen
@@leckyjake for synchronising, what things must be same in between these two type generators?
@@rifathasan3698 droop characteristics
Galing mo naman idol paano ba mag apply jan
Boss lecky both generator in manual
sir how to activate exactly preferential trip is there any simulation button ? please answer
SIR more Vedio po oras ETO tnx
sir what is the cause of power reverse trip.?
What actions to take if reverse power trip does not active during test?
you just have to check your settings
I did that too lods
👍
Sir, If we measure at 11 and 9 and we get 115v it means that the timer contact is in open contact?
No
Normally open?
@@rajatawasthi4769 please explain to me
Mr. lecky do not give people wrong explanation regarding preferential trip functionality target point. Please check it what is actual point for that protecting.
thank you for watching and i hope you should read then spread the love by sharing what you have.
You are doing well your job. That is good to continue to give your knowledge and help an others. I just give remark. Because you say preferential trip is use also because bus bar can not be accommodate such load in case over current is occurred. Actually only preferential trip is used to cut the power for non essential consumers 1 st, 2nd and 3rd group accordingly. That is all why use preferential trip to avoid to trip air circuit breaker (avoid black out). BUS bar is so strong and can be withstand any extremal loads ( wich is not requires any protection) will not affect any load to damage it.
It seems those timers don't last very long
Praxis Pms panel