Bind your flysky i6 or i6X to e011, e010, h8 mini with iRangeX irx6
HTML-код
- Опубликовано: 15 сен 2024
- Review of the iRangeX iRX6 multiprotocol module for flysky i6 or i6x and clones.
List of compatible protocols goo.gl/ZtvtX6
edit: i just figured out how this module works with a e010 and many more protocols
here are the instructions goo.gl/dt4Fns
also, the max roll and pitch angles seem to be more, so now my e011 goes faster than with the stock transmitter. and it is still possible to do rolls and flips but with stick commands. i'm loving this module!
I can make a video on how exactly to do it if you need, just let me know
links:
iRangeX iRX6 multiprotocol module goo.gl/kP8C1r
iRangeX iRX-i6X transmitter goo.gl/E4gxeA
Eachine E011 goo.gl/fxPwA8
Eachine H8 mini goo.gl/FRLAje - Кино
Hi, do you know a way to use it with eachine e013 plus? Thanks
spent far too long trying to get this to work with a e011, thought it was same protocol as the e010 for some reason! thank you very much for the video, made my day after all the time i wasted on this! :) flys so much better with a proper tx!
Not sure I have the same multiprotocol module, but mine was throttle down and right stick up and right while powering on, then you also have to keep holding up and right while plugging in the battery.
Jim Herreid thanks you mate!!!
Try moving the throttle up and down to bind the machine as you would with its own controller.
Cool thankyou I had no idea that was possible I had no idea what that plug on the back of my fs-i6 transmitter was but now I do cheers
after binding what is its range
Can a PDF version of the link from a link you have set up in English for example
Hi Doug, can you get the E011 to flip or select headless mode using Flysky i6x+iRangeX irx6?
good video, I have a doubt, I bought the multiprotocol and the eachine e011, it worked very well, suddenly I stopped synchronizing the flysky and the original transmitter , the dron turns on the led fast when detects the transmitter but does not finish synchronizing, you know which could be the mistake, thank you, excuse my English
nice video dough. Does this method also work for the eachine e58 drone? My current e58 transmitter doesnt bind with the new receiver(for e58) i just got. am thinking of a getting a flysky transmitter.
Will this work with the eachine p-51 mustang by any chance cheers
Thank you so much!!!!
Great video!!!
I have always wanted to know this!
How can i bind it to a hubsan x4?
Hi could u help me i have the fsi6 with module i use with the b03 pro works well but would like to order the bee brain lite an if u culd explain the process to control it i believe i shuld order frsky d8 i cant find this subject thanx
I range 7 Instructions say must be AETR on your transmitter. How can you input this? I'm using a flysky FS i6
Can you bind this to emax ez pilot?
Need help binding eachine qx95s to flyskyi6
How do you switch modes on e011 and e010? My i6 came with a broken A switch, so I mapped the "Normal/Sport" to the D switch. Doesn't make any difference in speed though. For E010 I hold both sticks to bottom right while powering on, and still holding them down, I plug in the battery to my module, for E011 the same except right stick to top right.
i don't think there is any modes when using an i6 with irx6. i believe the mode function was a part of the original e011/e010 transmitter
In the manual, no e011 in there...Can it bind certainly??
yes, i bind it with a e011 in this video
Can I bind it to my JJRC H67, boldclash b03-pro, and my betafpv FC?
Hold your sticks down and right and then turn on transmitter
Friend, do you know if the IRangeX FS-i6 i6x iRX6 connects with k120 or k110 that uses protocol futaba s-fhss
the irx6 does not connect to futaba. sorry
can i bind eachine novice ii too?
Should i use irx6 to connect my flysky fsi6 to ky101 drone? Thx
Thanks for this review, Doug. Might you have any idea if this module will work with a y-splitter cable and a trainer cable? I'm trying to find a way to get the i6x to work with this multimodule in a buddy box setup that can be used with my young son to fly an E011.
Plan B is to use a Beecore F3 FC (with Flysky protocol) on the E011.
yes it should work with a y splitter. i actually installed the module inside the transmitter, leaving the trainer port fully operational. here is a video of the mod ruclips.net/video/WLZyN_0VM9w/видео.html
could you tell me if it is compatible with Realacc R11, please?
Ihave the flysky i6 do you think that module would work on mine.?
ahh nevermind i didn't realize that your video title was actually flyskyi6 hahaha
what stick positions are needed to bind to the e011? or does it come "out of the box" read to do so?
i think it was the same as the h8 mini : Elevator up + Aileron right
Your directions didn't work for me, but following the printed info and turning on the TX with the sticks held in position worked. I only fly in mode 4, which was the whole point for me getting this protocol module. Otherwise I couldn't easily fpv toy micro-quads. I've been stuck with using micro F3 FC or Syma X11 boards.
Can the multiprotocol binding to yi zhan x4 tarantula?
Salut, est ce que quelqu'un connaît la manipulation pour eachine E016h, svp, marci..
Un listing, à jour 2020,existe t il ?
Marci de votre réponse
Good Morning. Does it work with Eachine e013? thankful.
Can you connect it to a h36
Does this work with any stock drone?
Would it work with the blade inductrix fpv
Will it work with eachine 013 ?
Does the 1s battery have to stay plugged in after it has bound to the quad?
yes, or you can mod it into your transmitter. like i've done in this video ruclips.net/video/WLZyN_0VM9w/видео.html
When you use the mpm, does the E011 automatically flip when you go full throttle?
no it doesn't
Hi, i can't fly my e011 because if i give some aileron or elevator it flips. You don't seem to have the same problem
+loryriga try to change your endpoints for aileron and elevator.
Thank you very much, it worked! Seems like you set the point when it flips via the endpoints, very interesting!
Doug Hnut it allows you to flip in movement
Awesome! i got the tip from another comment, i'm glad it worked out for you
I fixed my flip/roll tonight by going into my setup and setting the aux channel 6 to a switch. It had apparently been one of the knobs. Now I can flip the switch and it will flip/roll whenever the sticks max out, but otherwise it flies normally!
Does yours power on every time? Mine will work once then it won't work for a day or two then it will work for a couple flights and stop working again. I just ordered another one.
+DroneXFun 2 months ago. It stopped working. So i took a heat gun to it so that ut would soften the solder joints. And now it works every time. Does the led light up?
Doug Hnut Yes, it works. The whole thing works great, when it works. I will try the heat trick, thanks a million.
Nice block under the camera. Nice idea. My question is, can you change the rate modes on the e011? Does it fly in rate 1 or 2?
+Jerky Man thanks! the rate modes are built into the stock controller. So when flying with a i6 transmitter, there is no diffrent rate modes.
Doug Hnut is it in slow mode or does the i6 allow you to tilt the quad more? I already ordered it and I'll figure it out, just excited. I'm learning FPV with micros in the house. Good fun. Thanks for your time.
+Jerky Man the i6 allows you to tilt more. Have fun!
How much range e011?
Korean Dronian I get about 150 ft
Jjrc h36 won't connect the light goes sold but it never goes grenn it's always orange
But it won't connect at all ... I have a jumper t12 also that I can't get to connect either
Did you make any changes in FlySky i6 settings? Or just put the iRange iRX module in and everything would work? Describe please if you did. May be it is needed to firmware Flysky with "OpenTX" before? Thank you in advance!
no changes to the flysky i6 transmitter needed. plug the module in and bind to your toy drone with these instructions goo.gl/dt4Fns. here is an example to bind: for a e010 and a mode 2 transmitter, hold both the sticks to the bottom right while powering up the module. for a e011/h8 mini and a mode 2 transmitter, hold the right stick to the upper right while powering up the module.
it will remember the last protocol set.
Thank you very much!
Doug Hnut wow that was easy ! I have been having trouble with my h8
whats the stick command to bind e011? cant find it
Elevator up + Aileron right
Good vid looking and trying to get my mjx b6 to work with irange
do not do it, pal. B6 cannot bind with iR6x. and why would you do it? B6 TX is already a hobby grade controller.
HELP BATTERIE ,,,,,?????? MERCI
which is the fastest ?? JJRC h8 mini or Eachine E011
I deciding which one to buy.
Thanks you in advance for responding.
They both are quite fast for how small they are. i prefer the e011 for an overall better flying experience. the e011 has better recovery power from altitude drops(h8 mini has 6mm motors and the e011 has 7mm motors), better stability when hovering, yaw rates are not as crazy fast like the h8 mini, and the e011 is more durable due to the ducts.
waiting for e011 , want better fpv i have tx01 700/1000tvl ?
Works great. Tried to enable headless mode on E011, enabled channel 9, no luck. Anybody successful?
works great with e011 except I can not get flip to work? have tried channels 5 and 6.
+stu110 i can flip while flying if i chop the throttle and roll or tilt very quickly at the same time. If that dosent work, try increasing the endpoints in your transmitter settings.
will try that thanks, but thought it was possible to assign a switch to flip like on the tx that comes with the e011
i think you gotta flash it with silverware soyou can make it go acro. no button flips i think
Great find thanks for sharing👍
Can we use this for Furibee F36??? If it does. It's really cool!!,??
i don't think it will work. it is not listed in the supported protocols. and I did a quick search on the f36, and no one seems to have any luck with it. even the 4 in 1 multiprotocol module doesn't seem to support it
Yeh thanks for that👍😉
Going to get one for my son.
Connect fs ct6b transmitter
nfg on the battery = AvE reference?
lol yes!
Will this work with the eachine e013 and the flysky i6s?
sorry i am not sure.
no it doesntt, as the flight controller on the e013 will only allow it to fly with the provided transmitter, sorry mate...... but what iam doing is buying the eachine e011 flight controller - www.banggood.com/Eachine-E011-RC-Quadcopter-Spare-Parts-Receiver-Board-E011-04-p-1150074.html?gmcCountry=AU¤cy=AUD&createTmp=1&Cdm-cods-acc&gclid=EAIaIQobChMI3ezfrLbl3QIV2W1gCh1JmwBQEAEYASADEgJVifD_BwE&cur_warehouse=CN and putting that on my e013
flysky or devo for fast racing fpv ?
I prefer flysky thanks!
Did you use the h8 mini battery to power the irx6 ??
Renato Torrezani the h8 mini battery would work. I used a 600mah battery from a different drone
Thank you, whats the name of this connector ??
micro losi www.alibaba.com/product-detail/Wiring-connector-51005-Micro-losi-connector_60391825892.html
You need to unlock the throttle just like the stock reciever
Nice video.... what kind of range does this get?
Thanks! I haven't measured the distance, but it seems to be the same as the toy transmitter. I plan on doing a cheap external antenna mod it this.
Doug Hnut cool thanks....maybe no increase in range but the Resolution has got to be wayyy better.
thanks!
on syma x8c
range????
range is about the same as the original transmitter, which isn't very far. ~30m
Does it work with eachine e55 ?
sorry, I am not sure. i did a search and could not find out what protocol the e55 uses
It seems Eachine e55 = FQ777. So it should work ?
the list of compatible drones shows FQ777-124
which is a completely different drone goo.gl/LSpjGj
Hi it works with a jjrc h36?
sorry it does not
Will this model works with Furibee F36?
i don't think it will work. it is not listed in the supported protocols. and I did a quick search on the f36, and no one seems to have any luck with it. even the 4 in 1 multiprotocol module doesn't seem to support it
Dose this work with dm002 or f36 furibee ?
Hunter Mclaughlin i dont think it works with the f36 as they use a protocol that isn't supported , and im not sure about the dm002
Doug Hnut how do I get the beecore lite silverware to bind ??
THANKS!