@@samydou0412 Hi! Everything's ready, apart from the updated website. Turns out it takes more time than a week to make. If you give us a letter at hello@aukits.com, we can ship you the new kit now
I had a crack at my own after seeing yours, but used different parts and methodolgy. Great inspiration. Got mine up here on youtube but only a sound test. used Visaton BF37's and a 2x8w tinysine BT amp
@@toddroles3234 yep I did on the non tinysine amp equivalent. I bought a few of those similar boards and only got one to work properly, but that one does have the cap.
I think the diy one actually sounds better where as the JBL is kind of muddy and missing some treble. I think for the test though they should have both been 100% because sometimes the volume is not completely linear as it tries to adjust for human audio perception. I might be wrong though.
I am building a portable Bluetooth speaker system of 3+3 watts.It mainly consists of a filter less class d audio amplifier.The problem here is that when I am powering both the Bluetooth audio receiver & amplifier from a common li ion 3.7 volt battery,a noise is coming at speaker. I have a common ground for stereo audio out & power. But If I power using two separate batteries the problems solves ie. No noise.But it's not portable.Because I have to charge a single battery. In your speaker you have used differential audio coupling. I my design the reciever directly providing L,R & Ground . Is this this the cause for noise.
Not bad but u know that the charging board has a limited output of 1A, so if the battery is fully charged u get 4.2W out of it. U should use a different protection/ charging board with an output of 3A
Hi, I love your project! May I know what is the Bluetooth + Amplifier board that you used, since you've replaced that with the previous Bluetooth and Amplifier board. Thanks in advanced!
@@Max-oi9ge XD if that's what you think you're as stupid as a person gets XD second good luck with long duration on a DIY project and why do you hate jbl so much? Or you just can't afford a jbl and then you trashtalk that's what i think
@@Max-oi9ge XD your the typical idiot who thinks i am a fanboy no i am not bdw second of all you are not gonna explain why you hate jbl cause you have no reason to hate it. Don't try to argue any further m8 you full off trashtalk xD
I have two subwoofers of sound link 42mm (1.5 inch) How many inches of box do you have to make for this speaker's good effect? Without bass resonance. No Bass Resonance. is going to use Bass Air Tube
I have a Samsung PS-FC330 single speaker with impedance 3 ohm. I don't know how but -I want to attach a power AC supply . -I want to attach a 3.5 mm headphone jack -I want to attach a Micro usb, a usb-c and usb type a for input. -I want it to have bluetooth support. Can you please help me figure out what to do step by step.
Stores energy for bass heavy parts because dc booster can't handle the load fully. If there was no capacitor, sudden bassy notes could sometimes sound distorted
Hi! Is is for high current consumpsion when speaker move a lot. It basically accumulates energy and gives it back on low notes when the driver moves the most
@@Kart0nas ohhh, i see. So how do I calculate what capacitor I would need? I have a bt receiver + amp that gives out 10-20w depending on input voltage. I was thinking of driving it with around 12v (3x3,7v lipo in series and again in parallel) and I have 2x 8ohm speakers with 30w RMS
@@vaughanbiddle3123 if you go to 'about' tab in aukits.com you can see a link for battery below the 'Parts' and 'Specs'. Alternatively, go to a local electronics shop and ask for a 18650 Li-on battery that can provide at least 4 amps of current :)
Really good speaker. I always told my friends, hey JBL, BOSE and any other good brand, can be pricey for their brand not really for quality. Build another one same as this one but bigger with 30-40W each speaker so you would have 80W in total and add 2 tweeters too and a nice passive radiator. I bet it would sound awesome but use something in between 1.2cm or 2.5cm of MDF (thickness).
I know the speaker was probably made from fairly cheap parts, but if anything breaks, you can forget about fixing it, what with all the hot-glue you went to town with :-/
Bought the kit to work on as a project with my son. Very happy with the product. Thank you!
So glad to hear this, big thanks!
Does the kit include the battery
@@vaughanbiddle3123 It does not
@@aukits Какого размера пасивка?
Might I suggest instead of soldering the battery directly, get an 18650 battery holder for ease of replacement???
Agreed. How safe is it using all that glue and tape considering heat?
Thank you. Nice simple video and finish. Peace
You know why I'm rewatching this xD
:Dd nice nice
Did you make it?
How much did it cost?
The vocals are more crisp and the build has a improved bass. Really nice built!!
Loved it!!
Keep the good work.
Right on. I'm planning make one but I want to substitute with usb type C
There'll be a video next week. Kits are upgraded with usb c and new wood option
@@Kart0nas when do you believe the new version of the kit will be on sale? Looking forward to buy it!
@@samydou0412 Hi! Everything's ready, apart from the updated website. Turns out it takes more time than a week to make. If you give us a letter at hello@aukits.com, we can ship you the new kit now
Received my kit today and it has USB C
Nice design !
Great audio and video! Great job! : )
That's so cool!
I had a crack at my own after seeing yours, but used different parts and methodolgy. Great inspiration. Got mine up here on youtube but only a sound test. used Visaton BF37's and a 2x8w tinysine BT amp
3rutu5, did you use the capacitor?
@@toddroles3234 yep I did on the non tinysine amp equivalent. I bought a few of those similar boards and only got one to work properly, but that one does have the cap.
Good job. Would you please give the amplifier information?
ruclips.net/video/Z6OCaygi9ek/видео.html
I think the diy one actually sounds better where as the JBL is kind of muddy and missing some treble. I think for the test though they should have both been 100% because sometimes the volume is not completely linear as it tries to adjust for human audio perception. I might be wrong though.
u are a great worker .your video quality is awesome.nice bro
Loved this video and your build. Great music selection as well👍
Very nice by speaker and thank u for helping me build one
I am building a portable Bluetooth speaker system of 3+3 watts.It mainly consists of a filter less class d audio amplifier.The problem here is that when I am powering both the Bluetooth audio receiver & amplifier from a common li ion 3.7 volt battery,a noise is coming at speaker.
I have a common ground for stereo audio out & power.
But If I power using two separate batteries the problems solves ie. No noise.But it's not portable.Because I have to charge a single battery.
In your speaker you have used differential audio coupling.
I my design the reciever directly providing L,R & Ground .
Is this this the cause for noise.
Not bad but u know that the charging board has a limited output of 1A, so if the battery is fully charged u get 4.2W out of it. U should use a different protection/ charging board with an output of 3A
Very clear, like it!
Hi, I love your project! May I know what is the Bluetooth + Amplifier board that you used, since you've replaced that with the previous Bluetooth and Amplifier board. Thanks in advanced!
thank you so much, in advance ofc.
What is the purpose of the 16V 2200 capacitor between the step up converter and the bluetooth amp?
Cheers
Smoothing the rough voltage coming out of the boost converter definitely
Ahhh, that makes sense.
Thank you
Like. Nice speaker!
Your's are sparkly with enhanced bass imo.. inspiring mate... Subscribed... Keep up the good work..
GREAT qaulity !
can't believe you just have 190 subscribers.
have you come up with the kit idea before making youtube videos?
Hey, thanks! Yes, kinda. I had a few projects before but I did not upload them to the Internet.
@@aukits nice :D
Have you recorded them &
What are the plans for your next Project?
I appreciate your Work. Go on! :)
Indeed , maybe cuz he just have 1 video , should make more upload more !
Now he hast got 1500+ subs just from 2 vids LOL...
Tbh your speaker sounds way better
i can see you hate jbl XD overall the flip 3 sounds better but the DIY speaker is not bad neither its also a good speaker
@@chumhau6993 Wtf are you talking, his diy speaker sound 3x times nicer XD (Yes i hate JBL but im honest with you, JBL is just a hype)
@@Max-oi9ge XD if that's what you think you're as stupid as a person gets XD second good luck with long duration on a DIY project and why do you hate jbl so much? Or you just can't afford a jbl and then you trashtalk that's what i think
@@Max-oi9ge XD your the typical idiot who thinks i am a fanboy no i am not bdw second of all you are not gonna explain why you hate jbl cause you have no reason to hate it. Don't try to argue any further m8 you full off trashtalk xD
Jbl is more bassy and outdoor this is more hifi. My opinion.
Damn bro.. it looks great and the sound quality is even better..
Why did you hot glued all components ? What if you want to change something?
Nice Speaker...&Nice video!
Very good job
Should drop link under
7:01 posisi kabel speaker
Bisa bikin sendiri gak?
@@Ahmadboy12 bisa gan m.facebook.com/story.php?story_fbid=486895918821193&id=100025023676591
@@Ahmadboy12 ini hasilnya m.facebook.com/story.php?story_fbid=496678774509574&id=100025023676591
@@prajadeeska4657 mantap, aku juga lho 😛
@@Ahmadboy12 salam satu hobi 😁
Can you please tell me what is the difference between the red & blue wires used when you start soldering and the red & black wires used near the end?
no real difference, only that the black&red wires at the end are glued together into one wire for neatness
Is it possible to make it a 20w speaker if you replace the speakers with 10w speakers and give it a stronger amp?
yes, though the dc boost module tops out at ~15 W
Super i am waiting for this
Your speaker is better than jbl 4 👍👍👍👍
Nice speaker bro
Кто-нибудь, подскажите, с какой целью ставится конденсатор на выход повышающего модуля? Сгладить пульсации?
I have two subwoofers of sound link 42mm (1.5 inch)
How many inches of box do you have to make for this speaker's good effect?
Without bass resonance.
No Bass Resonance.
is going to use Bass Air Tube
Donate them to someone who possess the knowledge!😡
@@rahultej2248 किसके पास नॉलेज हें! पता भी बता दो😂😂😂
tatya vinchu Me, obviously
Cool speaker, what does the passive part do? Is it needed? Thanks
Well it is used to increase the bass of the speaker and also it help to make it water proof
@@aayushsharma6233 yes it radiates the bass. That is why it is called a passive radiator. But it certainly does not make it waterproof
Name of the wood?
what'll be the cost to build this project
Great Built boi
I have a Samsung PS-FC330 single speaker with impedance 3 ohm. I don't know how but
-I want to attach a power AC supply .
-I want to attach a 3.5 mm headphone jack
-I want to attach a Micro usb, a usb-c and usb type a for input.
-I want it to have bluetooth support.
Can you please help me figure out what to do step by step.
What does the 2200 uf capacitor do?
Stores energy for bass heavy parts because dc booster can't handle the load fully. If there was no capacitor, sudden bassy notes could sometimes sound distorted
@@Kart0nas thanks I was experiencing this issue without one. Why doe is have to be a higher voltage than the 6.5 volt from the booster?
@@laurensguijt u mean the capacitor voltage? if the cap's voltage below the booster voltage. the capacitor could be a bomb
nice skill bro
Good job brother
Ur doin fine and great
What glue are u using?
ArdiNugroho it’s hot glue
Nice one. Wondering how many people do you have in the team?
Thanks, 2-3
How many max voltage that board can handle? I want to apply 8 watt speaker
the jbl has more bass tho but overall the DIY speaker is awsome i love it
You should add components names in the description
Why you don't have much subscriber
Your speaker is best
Thanks thanks
@@aukits bro your speaker is better than jbl
I have one RDA 5856 ete pcb, one old mi power bank, can I use them to make this?
I want the speaker please give me🥺🥺🥺🥺🥺🥺🥺🙏🙏🙏🙏🙏
I'm about to do my first diy bt speaker with little knowledge about electronics and I'd like to ask something: what is the capacitor for?
Hi! Is is for high current consumpsion when speaker move a lot. It basically accumulates energy and gives it back on low notes when the driver moves the most
@@Kart0nas ohhh, i see. So how do I calculate what capacitor I would need? I have a bt receiver + amp that gives out 10-20w depending on input voltage. I was thinking of driving it with around 12v (3x3,7v lipo in series and again in parallel) and I have 2x 8ohm speakers with 30w RMS
Omg it looks great
Hello, would you mind telling me what amplifier & Bluetooth board you are using for this speaker? Thanks
Csra64215 + ht6872
Thanks
I ordered a speaker kit but what size wire do you recommend to solder with?
Hi. 22 - 20 AWG will work just fine
А объем корпуса и пассивный излучатель подбирали по лабораторным данным, или примерно?
примерно
Hello, did you deliver to France ?
Hi, yes. Shipping is worldwide
ಠ_ಠ
D
*Could you please tell me the length and breadth of the speaker*
The enclosure is roughly 190 x 60 x 45 mm
@@Kart0nas*thank you so much for the information*
Looks like your diy sound beter than jbl
Is the battery included in the kit?
It is not
Does the electronics kit on your website come with the battery
It comes without the battery
Jokubas Mickus how do you get the battery then. Thanks
@@vaughanbiddle3123 if you go to 'about' tab in aukits.com you can see a link for battery below the 'Parts' and 'Specs'. Alternatively, go to a local electronics shop and ask for a 18650 Li-on battery that can provide at least 4 amps of current :)
Jokubas Mickus ok thanks alot ur videos great by the way
Как ты врезал так ровно детали еорпуса и отверстия?
Лазерная резка это
What is the size? LxWxH?
4:00 - надпись на флюсе на русском языке
P.S. дружище, подскажи, пожалуйста, породу древисины, заранее спасибо
Really good speaker. I always told my friends, hey JBL, BOSE and any other good brand, can be pricey for their brand not really for quality. Build another one same as this one but bigger with 30-40W each speaker so you would have 80W in total and add 2 tweeters too and a nice passive radiator. I bet it would sound awesome but use something in between 1.2cm or 2.5cm of MDF (thickness).
Your speaker sounds hifi compared to the JBL
JBL is more outdoor and bassy
And the jbl is and old one
The DIY has kore fuller treble than JBL flip 4
Sale?
What are the part sizes
plesase.....
Very very nice Kit. I like it. Simple but nice.
is it 1.5 inch speaker..?
How do u cut that ports for charge ...
Everything is laser cut
What amp you used?
What size?
I can have a 3W woofer?
Wow! are you engineer? Can i have shipping to Canada?
Thanks thanks! Yeah, just go to aukits.com, you'll see that shipping is worldwide
Oh, and I am not an engineer, trial and error is how I came up with this specific speaker design
@@aukits Thankyou for your answer!
What's the total costing?
Visit the website, it is in description
65$
Wow sehr gute Video Qualität und Super Projekt. Ich hätte bessere Treiber genommen, dann hättest du ein Besseres Ergebnis erzielen können. Super 👍🏻
Many Thanks. These speaker drivers are actually one of the best little ones. Sorry for my German, I only studied it for a year
well done
Podrías venderme una de esos dispositivos?
Hot glued to all electronics connections and boards looks messy! Can't we not use anything better alternative than this to looks well?
What are the part sizes
jbl is in 2nd position
I know the speaker was probably made from fairly cheap parts, but if anything breaks, you can forget about fixing it, what with all the hot-glue you went to town with :-/
@ title clip sound is fake
Yeah its fake 😤😤😤
what size speakers are those
Drivers are around 40 mm in diameter
More Tutorial's with more mobility small speaker :D
Из какого материала сделан корпус
Не ожидал увидеть российский флюс !!!
which amplifier is that?
NS4110B
Amazing i like you Channel
Bluetooth audio module has I2S output or Analog output ?
Hot glue... an electrical engineer/makers' worst enemy. STAY BACK!!
И тут до меня дошло что это делал русский..
Спалил тебя клей момент
Еще и флюс
я флюс наш русский сразу заметил.
wireless board price
100;00000000
I made it but there is a problem. The speaker cut off the output when increase the volume on some loudly music why...any experience?
Из какого материала сделана?
Из дерева
Love funky