I love compact machines and lathes are one of my favorites.😍 This lathe looks perfect my Friend and Thank you for showing us.🙏🍀🍀🍀 As I understood, can be make a thread from 0.5 to 3 mm?
If you still didnt got one. I got one last week. And it is very well build compared to what i know abot this model from russian and german forums. I will add electronic lead screw to this definitly.
A whole new technique in appraising a tool and good to see a deaf, mute person giving it a go. In his silent world and totally wrapped up with protective garments to protect his skin from the modern world, I'm sure he is very happy in his achievement with this video.
Cool video I'm just wondering you said it has a 38mm spindle bore, does that diameter continue through the machine to the hole at the back for long items?
Probably a good idea to completely remove the chuck jaws, clean them, and lubricate the scroll and the bottoms of the jaws, that engage with the scroll.
Hey sir! I like your wm210v . I just got mine last week. It’s working great,only a few threads options did not work for me. Can you do me a favor? I have a bit of problems on thread pitch of 1.25mm . When I was change the gear according to diagram on the has shown us. I have tried exactly as it’s said, but it’s came out the first ran of 1.25mm tested was right pitch,and then I added the depths cuts it cut defer off cut ! I don’t know why? If you know what was or you got some clues please help me out sir! Thank you so much. God bless you!
Hello - Nice video.... but why do you have to put something under the cutting tool...? Shoulden't the center line and the cutting tool be adjustede from the factory?
unfortunately there is no way to reverse auto feed unless you reverse motor direction , but in this case you can't cut ! Spindle and lead screw are directly connected.. You can get what you need by adding a reverse gearing mechanism or an Electric lead screw...😅
Ive had one for a year, every where you look there is problems . Vibrations over 600rpm, tailstock does not match center height of the spindle, mods needed. 3 jaw chuck will not spin true. Speed control knob may keep spindle spinning even when turned to zero. Cross slide is unstable, compound slide travel 23.mm. Compound slide gib adustments not consistant. Way too much play in the feed screw 1/2 turn before movement. Cross feed the same. Cross feed slide gib adjustment not consistant i.e. adjust at one end will be tight or loose at the other end. Carriage not aligned to feed screw so when you engage the feed screw it binds and lift the when tightened. There is so much more but I'm tired of writing. Really you need another lathe and a Mill to fix it all.. With all of these problems I'm glad I bought it. It functions just well enough to get small jobs done. Also If you want to be able to do anything slightly complex you will need to spend much more than the cost of the lathe on accessories & additional tools. A fun and expensive hobby . Cheers!
Hi friend, thanks for your comment. Yes it really is! I made a lot of improvements and adjustments to everything. Now there is no vibration and it works normally, but you really have to take the time to adjust it.
Law #1 loose the long sleeves.
I love compact machines and lathes are one of my favorites.😍
This lathe looks perfect my Friend and Thank you for showing us.🙏🍀🍀🍀
As I understood, can be make a thread from 0.5 to 3 mm?
This is the step of the threads. My friend thanks for the coment👌🍀☺️
@@HandmadeCreativeChannel ,
Please provide the address and contact number of the dealer/distributor of this lathe, for Indonesia.
Is posible male thread milimetric?
I just saw this mini lathe on Amazon and thought it was an interesting option. How has it turned out for you after a year since this video?
So..., where does one buy that wm210v-s lathe shown in your video?
It's on Amazon and AliExpress
@@drumtwo4seven
Thanks for the info.
From what I saw in this unboxing and first chips, it seems like a decent machine.
Halo is posible make thread milimetric?
I see you just got this lathe, i think this is the one i want to get, how do you like it so far? Thanks for showing the test cut.
If you still didnt got one. I got one last week. And it is very well build compared to what i know abot this model from russian and german forums.
I will add electronic lead screw to this definitly.
Пожелавам ти да те слуша и радва машинката и много успешни бъдещи проекти.
That would be very useful tool for you 😉
Yes my friend 👌☺️🍀
@@HandmadeCreativeChannel ,
Please provide the address and contact number of the dealer/distributor of this lathe, for Indonesia.
Nice and welcome to your workshop 👍
Thanks brother👌🍀
@@HandmadeCreativeChannel ,
Please provide the address and contact number of the dealer/distributor of this lathe, for Indonesia
A whole new technique in appraising a tool and good to see a deaf, mute person giving it a go. In his silent world and totally wrapped up with protective garments to protect his skin from the modern world, I'm sure he is very happy in his achievement with this video.
Hello my friend. How can I get such a lathe and how much does it cost? Best regards
basically the same model as a Vevor mx-210V. Just go onto their website.
I like the large bore for a small machine. 5 morse taper
Cool video I'm just wondering you said it has a 38mm spindle bore, does that diameter continue through the machine to the hole at the back for long items?
Yes, the way you described it, that is what that spec means.
Probably a good idea to completely remove the chuck jaws, clean them, and lubricate the scroll and the bottoms of the jaws, that engage with the scroll.
O que achou do torno.Pequeno demais ou no tamanho certo
Hey sir! I like your wm210v . I just got mine last week. It’s working great,only a few threads options did not work for me. Can you do me a favor? I have a bit of problems on thread pitch of 1.25mm . When I was change the gear according to diagram on the has shown us. I have tried exactly as it’s said, but it’s came out the first ran of 1.25mm tested was right pitch,and then I added the depths cuts it cut defer off cut ! I don’t know why? If you know what was or you got some clues please help me out sir! Thank you so much. God bless you!
Hello - Nice video.... but why do you have to put something under the cutting tool...? Shoulden't the center line and the cutting tool be adjustede from the factory?
Gia ban Bao nhieu?
Where did you purchase this lathe?
I'd love to see a follow up video now that you've had the lathe for almost a year.
hello I would like to buy this tour. but I have a question please:
the auto feed screw can it move in both directions of rotation? thank you
unfortunately there is no way to reverse auto feed unless you reverse motor direction , but in this case you can't cut !
Spindle and lead screw are directly connected..
You can get what you need by adding a reverse gearing mechanism or an Electric lead screw...😅
I find myself wondering whether I need a lathe now. Thanks for nothing. 🤣
It's not the lathe I'm worried about, it's the table 😁👍👍
بسیار عالی ، متأسفانه مادر شرایط تحریم هستیم و این ابزارالات بدست ما نمیرسد، متشکرم
Koja je cena i gde se moze poruciti,adresa
Where can I buy this?
Bhaiya machine ka price Kitna
Nice.
Where did you buy it?
؟
How many price this sir
500 quid
Ive had one for a year, every where you look there is problems . Vibrations over 600rpm, tailstock does not match center height of the spindle, mods needed. 3 jaw chuck will not spin true. Speed control knob may keep spindle spinning even when turned to zero. Cross slide is unstable, compound slide travel 23.mm.
Compound slide gib adustments not consistant. Way too much play in the feed screw 1/2 turn before movement. Cross feed the same. Cross feed slide gib adjustment not consistant i.e. adjust at one end will be tight or loose at the other end. Carriage not aligned to feed screw so when you engage the feed screw it binds and lift the when tightened. There is so much more but I'm tired of writing. Really you need another lathe and a Mill to fix it all.. With all of these problems I'm glad I bought it. It functions just well enough to get small jobs done. Also If you want to be able to do anything slightly complex you will need to spend much more than the cost of the lathe on accessories & additional tools. A fun and expensive hobby . Cheers!
Hi friend, thanks for your comment. Yes it really is! I made a lot of improvements and adjustments to everything. Now there is no vibration and it works normally, but you really have to take the time to adjust it.
I need your suggestion.... I'm confused between this machine to buy or used emco what do you suggest
Price
الثمن لو سمحت ❤
Jump to 11:24 to get to the meat and potatoes 😄
The one I “bought “ has many “Chinese ,quality problems” ie. sintered gears that devolved , rapidly. Hopefully you have more luck.
I agree with you, but everything is flattering are normal with small improvements. Parts in my region have, and are pretty cheap.
@@HandmadeCreativeChannel ,
Please provide the address and contact number of the dealer/distributor of this lathe, for Indonesia.
chi lo vende e quanto costa?
Mesin impian dan masih belum terbeli karena faktor ekonomiku rendah.
🤝🍀🍀🍀
Thanks brother 👌☺️🍀
@@HandmadeCreativeChannel ,
Please provide the address and contact number of the dealer/distributor of this lathe, for Indonesia.
ممكن سعر
Is this guy from another planet, is he mute, What's with all the protective gear?
Дали.може.да.секупи.и.колку.кошта
Jednz minuta 40 sekund , najwarzniejszy kawałek filmu , otwieranie skrzyni, po prostu żenada.
I can’t believe you have not built a proper stand for your lathe, expect problems.
No coolant run off poor design.