Creality CR-Touch - Auto Bed Leveling Probe - Ender-3 V2
HTML-код
- Опубликовано: 7 окт 2024
- Installing the CR touch on the Creality Ender 3 V2
Buy Cr-Touch: geni.us/9nGmb
Recommended: geni.us/JustVlads
Creality CR Touch Auto Bed Leveling Sensor Kit. Creality Official Specially Designed for Ender 3 v2/ Ender 3/ Ender 3 Pro/Ender 5/Ender 5pro/CR10 for 32 Bit V4.2.2/V4.2.7 Mainboard 3D Printer
My main channel @Just Vlad
As an Amazon Associate I earn from qualifying purchases
Buy Cr-Touch: geni.us/9nGmb
Recommended: geni.us/JustVlads
There are 2 small holes that are threaded it is extremely hard to see in the video, once you install the Cr touch bracket you now see the mounting screws
Watched 4 other videos and nothing worked. Your video helped getting my printer to level on the first try. Thank you.
Precise and articulated. I noticed your cr touch only has 3 across touch points. I installed CR Touch and mine has 49 touch points. Is there a way to change that?
I am confused, at the beginning of your video there are "NO" holes on the mount next to the fan, then around 6:12 there are two holes in the mount. Where did these holes come from??
Mine probes the centre, and that's it... no 9 points
Mine won’t get any closer than a 4mm gap. No matter what I do. Do I have a defective unit? Or just a stressful hobby?
Maybe your build plate is to low for the y axis to go all the way?
@@thatguy7612 I have since figured it out but thank you anyway! It wasn’t that. But I needed the “GD version” of the software👍
No editing the Gcode?
I like your channel you are so underrated
Hello, do you know how to correct that when leveling, the test measures outside the print bed?
i believe you need to remove the z stop switch. it is not there on my ender 3 v2 neo and i took it off on my reg v2
I’m having problems with my my hot end Keeps going right and makes a nasty noise. Can someone help me I can get it to work
I don't have the CR Touch, But after a firmware update, the X Y And Z are blinking with Questionmarks. The AutoHome sends the head of the charts and makes some noises when it can't go any further. Any quick suggestion what to do?
PS: Im a Total noob when it comes to printing. This is my first 3D Printer.
Why does my auto home not go to the middle ? Setting this bed up is killing me lol
Can you give some more tips on this, I downloaded the same firmware you did, and I know my motherboard is version 4.2.2, but I can’t get it to work, please help
Same.
Do I need to add anything to the startup code in Cura?
Yeah, you need to add on the cura printer config, in the start G-Code a G29 after G28, so it does the auto leveling in each print
G28 ;##########
G29 ; Auto Bed Leveling
I followed your video. Downloaded the file and put it on the SSD card. Put the card in the printer and Iall I got was a blank screnn and that was it. Basically nothing.
Same. Mine won’t boot now
Hi! i have a Ender 3 Neo
I just follow the steps for the bed leveling manually, pretty much like in this video, but at the time when the auto-level finish, the noozle get stuck into the bed at the end position.
So... i see in other videos and a lot of people got the same result... a scrached bed :/
When this happen, who's fault? firmware or user?
I fixed after that by leveling up the z-offset, but i don't understand the real function of the CR-Touch
Now i'm scared of using again the auto-level function.
Bye
I cant get the software to download. Not sure why? Help any suggestion's.
My issue is my pla doesn’t want to stick to the bed after adding the cr touch. Any tips?
its probably the bed not being correctly leveled, you might have to make it a bit lower to the bed
the file is currupt guys bed level file
How do you get the working file?
I am also looking for the CR touch firmware file that works for the 4.2.2 motherboard. watching this thread. @@pianoplayer1224.