Anycubic kossel linear plus upgrades including TMC 2208
HTML-код
- Опубликовано: 26 авг 2024
- Anycubic kossel linear plus delta 3Dprinter updates and upgrades I have made including TMC 2208 and printer parts links below all from thingiverse
www.thingivers... top caps
www.thingivers... corner braces
www.thingivers... sensor holder
www.thingivers... cable holder hot end
www.thingivers... tool holder
www.thingivers... fan duct
I found the metal effector plate on mine wasn't threaded accurately and it meant the effector was never parallel to the plate. To reduce noise and tighten things up I also printed a clip for each rod and slid them halfway down the rods with a small rubber band pulling them together. You got some nice mods there , Thanks for sharing.
Nice video mate. thank you for sharing
Thanks
Hey mate great vid, found a couple of useful parts to upgrade. Just wanted to ask, when you swapped out the A4988 for TMC2208 V2, did you have you do many changes to firmware, or did you just get away with changing the stepper motor wiring? Looks like theres a V3, i was thinking if it would also be a drop in replacement? I'm attempting to try this but dont think I have the time to mess about with the firmware.
With the v2 stepper I didn't have to change anything with the firmware or the wires I just had to set the volts with a voltage meter which was the hardest part. That's why I picked them as i didn't wish to mess with the firmware or wires and they made the best improvement over all.
Love the upgrades, I have done most of them but not the corner braces, nice one.
What firmware are you running for the TMC 2208 please? I like mine, but trying to find someone who has reliably modded the firmware to use the new drivers.
Hi i never changed the firmware im still running the original and it runs fine 🙂
Hi, why do you only have 3 of the TMC2208's installed?
Hi I only put them on the 3 arm motors the extruder doesn't really need one and that was a good thing as I got 4 but I ruined one by mistake 🙄so lucky had a spare 🤣
@@brithawkes36 Hi , what value did you use for Vref ?
@@ultrabeamitaly1 hi I set them to 0.845
@@brithawkes36 thanks
could you please tell me where to find that little blok where that key chain thingy is hanging from.. much appreciated
Hi William I draw it my self as I couldn't fine one I liked if you would like it fined me on Twitter @martin_hawkes_1 DM me a email address and I will send it to you
@@brithawkes36 oh that would be awesome man, thank you so much..
@@brithawkes36 Hey nice Job! would like to print this block too =) i got no Twitter :S Maybe can i DM somewhere else?
@@crispssmacks4556DM me on twitter
@@brithawkes36 i cant find you on twitter in messages
hello can you tell me what vontages you setup on your tmc drivers?
Hi to be honest it was a long time ago and I can't remember I know I found the information from Facebook and set them from that and they have been fine sorry I can't be of more help if i fine the figure I will update you
@@brithawkes36 at that sucks it got ones but now sure now if i apply them, i have the ones that dont have the 3 pins on top not usre if i put them on now
@@TheNautilus99 hi I just checked the video I set them to 0 845
@@brithawkes36 thanks!
Hi thanks for video its so usefull🙏
İve got a question. How can i use tmc2208 with stock firmware? Couse it needs to reverse stepmotor. Or must to use marlin with your setup? 3 tmc and 2 a49?
Hobby Maniac hi with TMC2208 v2 I didn’t have to change anything just checked the voltage which I was very happy about until I turned on the printer I wasn’t sure what would happen but all was fine try and make sure you buy version 2 2208 and you shouldn’t have to make any changes to the motors or marlin if when you turn it on the the printer move down. When you home then you will have to change marlin 👍
Brithawkes 3DP hi thanks for reply. İ checked and ive got v1 tmc2208. And im very comfortble with stock firmware. İ add da hai s firmware but i couldnt figure out bed leveling and micro leveling while printing. İ m going to set stock drivers and stock firmware.
Brithawkes 3DP can you give me a link of your tmc2208 version? İll try to buy local. And then i can use it with stock firmware right? İts supper 🤘
Hobby Maniac link to amazon
KINGPRINT TMC2208 Stepper Mute with Heat Sinks Driver Stepstick Mute Replacement A4988 Drv8825 for 3D Printer(Pack of 4 PCS) www.amazon.co.uk/dp/B07GJ7L48H/ref=cm_sw_r_cp_api_i_vY1mDb1Q72AJA
where can i find the files for the little plate that covers where the screen is?
I think I found them on thingverse or myminifactory
@@brithawkes36 I looked but that exact file is missing from the guy that designed it :(
@@darktrojan00 sorry about that I would send it to you but unfortunately i don't have it anymore 😔
hello, im new here, can you give me a tutorial or clue for instal Tmc 2208??
Hi in the video I give most of the info if you have the same printer and get 2208s v2 then it is straightforward pull the old ones out and put the new ones in and set the voltage this you can find in other videos which will explain it better that I can you will need to print a fan housing and get a fan then find the place to plug it in the board I think I point it out in the video because I got the V2 I didn't need to mess with the firmware it just worked. I hope that helped a bit it was pretty easy when I started the only mistake I made was when testing the voltage I blow one stepper luckily I had a spare 😀 good luck
@@brithawkes36 i just found tutorial from lukas pomycal is very hard to follow for newbie😂