brilliant, i liked the psu connection to mainboard. the board says 5+ and 11+ but red psu wires say nothing and i didnt want to fry the board. a massive help .... thank you!!
When I went to attach the carbon rod connector on to the linear rails I realised you had included 12mm long m3 blots which are used on the old printer rather than the 8mm m3 ones as stated in the manual. Now i have had to go and buy the right size ones! It's a shame because I thought the rest of the kit was brilliant. What can I use to lubricate the linear rails as the cartridges are sticking slightly?
I enjoy this printer but now I have an issue with it. It would work fine and the auto level feature is awesome but 10 prints later and now the printer stops approximately 1 hour into the print. I tried to upload the firmware again so that it can have a fresh install but it won't install. I tried following the instructions from the anycubic site but all it does when trying to install while using cura is the startup text and a series of rectangles. I ordered a separate trigorilla board but I still can't upload onto that either. I ordered another printer and hope that you can help with me fixing the current printer that I have and I will use the new one that I am getting this monday. I was going to upload printing timelapses on my RUclips Channel of my custom work but can't. It is easier to get a timelapse made when it is a delta printer.
Hmm the rails on my kit are not long enough to reach the end stops on the rails. Is this ok? They have the same number of holes as the rails in the video, but they are about 3.5cm too short
My extruder heats to 200 fine, but once I start printing the temperature just drops and drops. I dont have insulation tape on my thermal block, that might help. What do you think is going on bad motherboard?
Could you please tell me where the other end of the white thermostat wire goes? I see the plug end go on the board but the other end is like a glass bead with the two wires inside. I have no idea where it has to go. Thanks.
The leads off the power supply arent marked, but the connection point on the board says 5A and 11A....... so just hook them up?as long as its positive to positive.... I have the same power supply as in the Vid but the manual references the "old" P/S with the long block of external connections......
had the sane Problem, i solved by Opening the black part of the powersupply, from which on you could see the Connections like it is stated in the Manual ;)
My Mainboard Broke I Bought a Ramps 1.4 With Aurdino Mega Board is it possible to run a ramps setup on anycubic kossel delta 3d printer it looks like it installed the custom firmware trough cura but it wont show on the display when I connect the ramps board?
Greetings, I'm interested in your products, but kinda confused about which one should i choose: i3 mega or this one? And why? I would like a printer able to deal also with other materials than pla, easy to use. I'm gonna use it to build some support, case and so on for electronic components. But not only this. I have enough space, so don't need to take this point in consideration. Please help me out, i want to place a order asap. Thanks
Hey thanks for your message. I3 Mega are basically ready to use and Linear Plus need hobby level hands-on assembly (which comes in as a DIY kit). Both performance very well and come with a very detailed instructions. Both printers can deal with PLA, ABS, PETG... so please choose the one that suits your need. And of course you are welcome to leave us a message for further questions. Cheers,
I just finished building my Kossel linear plus (first 3d printer) and got it all leveled, but It can't find any test files on the sd card to print, I plugged it into my pc and there are some stl files on there but i have been told that i will need a gcode file or something?
Yes, you need to use a program to convert STL files into a gcode file that the printer can interpret. This involves telling the slicing program (slic3r or Cura or whatever) what sized nozzle you are printing with etc.
I have a question I seen a few reviews on this printer and they all had board issues were the software was really old and the printer didn't work correctly if I buy this will I run into the same problems and if so because im new I wont know how or what to do to upgrade the software can someone explain and help direct me to the correct place if that might be correct what im asking?
Hi, Sir. If you need the update firmware and drivers, please go to our official website to download. Any other technical problems, please contact our engineers for help via the customer-service function. Here is the link to the official website: www.anycubic3d.com/aftermarket.html
Hello I just bought the US $320.00 plus from amazon so can you tell me if I get the auto level with it? if not I would like to get it. where can I get the auto level part? I can not wait to put it together and start printing.
Hi bladesoutnow, I am sorry that we just sell auto-leveling Kossel printer now, but we will sell auto-leveling parts. I will send a post if available on Facebook or VK. Facebook: facebook.com/anycubic3dprinter/ VK: vk.com/anycubic Or you can also subscribe our AliExpress shop: bit.ly/2xN0uyy
Have you tried running a serial connection to the printer using a slicing software? Common Marlin Mcodes may help out with that. M500 For example is save all current settings, M503 Is view all current Settings.
You forgot a very important step before plugging in power supply into the mains. Check the correct mains voltage on the power supply 110/230 switch.
that seems waaay tooo easy compared to the previous pulley version.
I wish I had waited an extra few weeks.
nice job.
We've released it on our official Aliexpress shop: goo.gl/9WoZo2
brilliant, i liked the psu connection to mainboard. the board says 5+ and 11+ but red psu wires say nothing and i didnt want to fry the board. a massive help .... thank you!!
Can't wait for the upgrade kit for mine.
When I went to attach the carbon rod connector on to the linear rails I realised you had included 12mm long m3 blots which are used on the old printer rather than the 8mm m3 ones as stated in the manual. Now i have had to go and buy the right size ones! It's a shame because I thought the rest of the kit was brilliant. What can I use to lubricate the linear rails as the cartridges are sticking slightly?
I enjoy this printer but now I have an issue with it. It would work fine and the auto level feature is awesome but 10 prints later and now the printer stops approximately 1 hour into the print. I tried to upload the firmware again so that it can have a fresh install but it won't install. I tried following the instructions from the anycubic site but all it does when trying to install while using cura is the startup text and a series of rectangles. I ordered a separate trigorilla board but I still can't upload onto that either. I ordered another printer and hope that you can help with me fixing the current printer that I have and I will use the new one that I am getting this monday. I was going to upload printing timelapses on my RUclips Channel of my custom work but can't. It is easier to get a timelapse made when it is a delta printer.
get rid of the sd card
Hmm the rails on my kit are not long enough to reach the end stops on the rails. Is this ok? They have the same number of holes as the rails in the video, but they are about 3.5cm too short
My extruder heats to 200 fine, but once I start printing the temperature just drops and drops. I dont have insulation tape on my thermal block, that might help. What do you think is going on bad motherboard?
Could you please tell me where the other end of the white thermostat wire goes? I see the plug end go on the board but the other end is like a glass bead with the two wires inside. I have no idea where it has to go. Thanks.
Here's a guide how to Bed Level & starting a print from SD card - Anycubic Kossel Plus 3D printer
ruclips.net/video/rIZwiLdPkg8/видео.html
#Medelis3D
Has a fan been added to keep the board cool?
What moter are you using? i wanna buy another one
Does it come with a mosfet to help control the heated bed?
all the linear guide carriages at 2:40 should slide down. maximum force and they don't move. Had 1 of the 3, that is fault.
The leads off the power supply arent marked, but the connection point on the board says 5A and 11A....... so just hook them up?as long as its positive to positive.... I have the same power supply as in the Vid but the manual references the "old" P/S with the long block of external connections......
I just checked and they're electrically common, doesn't matter which way round unless one set are thicker, in which case those are the 11 amp leads.
Thanx HaxR3!! I did finally come to that conclusion. Their manual needs to be updated to include that. ITs printing!!
had the sane Problem, i solved by Opening the black part of the powersupply, from which on you could see the Connections like it is stated in the Manual ;)
My Mainboard Broke I Bought a Ramps 1.4 With Aurdino Mega Board is it possible to run a ramps setup on anycubic kossel delta 3d printer
it looks like it installed the custom firmware trough cura but it wont show on the display when I connect the ramps board?
Witch of the two versions is this?
Very nice
Greetings,
I'm interested in your products, but kinda confused about which one should i choose: i3 mega or this one? And why? I would like a printer able to deal also with other materials than pla, easy to use.
I'm gonna use it to build some support, case and so on for electronic components. But not only this.
I have enough space, so don't need to take this point in consideration.
Please help me out, i want to place a order asap. Thanks
Hey thanks for your message. I3 Mega are basically ready to use and Linear Plus need hobby level hands-on assembly (which comes in as a DIY kit). Both performance very well and come with a very detailed instructions. Both printers can deal with PLA, ABS, PETG... so please choose the one that suits your need. And of course you are welcome to leave us a message for further questions. Cheers,
Will there be a upgrade kit for those of us with the version 1 of this unit?
Yes. Please kindly follow our official Facebook account. We will post the latest news about us there. :)
您好:請問電源接線正負是否有分插入孔?
I just finished building my Kossel linear plus (first 3d printer) and got it all leveled, but It can't find any test files on the sd card to print, I plugged it into my pc and there are some stl files on there but i have been told that i will need a gcode file or something?
Yes, you need to use a program to convert STL files into a gcode file that the printer can interpret. This involves telling the slicing program (slic3r or Cura or whatever) what sized nozzle you are printing with etc.
hello, where can I download the Marlin version installed at delivery?
I have a question I seen a few reviews on this printer and they all had board issues were the software was really old and the printer didn't work correctly if I buy this will I run into the same problems and if so because im new I wont know how or what to do to upgrade the software can someone explain and help direct me to the correct place if that might be correct what im asking?
Hi, Sir. If you need the update firmware and drivers, please go to our official website to download. Any other technical problems, please contact our engineers for help via the customer-service function. Here is the link to the official website: www.anycubic3d.com/aftermarket.html
So the bed just sits there with no screws? SMH
Great
I would love to showcase that Delta on my Channel and make a Review for it
buy it. dont wait for a free cookie xD
where can i buy the spare hotend for kossel
Hi Sir. You can buy it in our online stores: AliExpress, eBay, Amazon.
That printer, is it new version or the old version
New version, auto-leveling
Hello I just bought the US $320.00 plus from amazon so can you tell me if I get the auto level with it? if not I would like to get it. where can I get the auto level part? I can not wait to put it together and start printing.
Hi bladesoutnow, I am sorry that we just sell auto-leveling Kossel printer now, but we will sell auto-leveling parts. I will send a post if available on Facebook or VK.
Facebook: facebook.com/anycubic3dprinter/
VK: vk.com/anycubic
Or you can also subscribe our AliExpress shop: bit.ly/2xN0uyy
ANYCUBIC 3D ok aI will cancel my Amazon order that I just placed last night.
what color do you have in stock? also how fast can I get it shipped to USA?
Which platform you prefer to( Aliexpress or Amazon))
ANYCUBIC 3D I like Amazon
Those "tnuts" are the biggest load of crap. Why dont you provide proper hammer head style tnuts?
Second biggest complainta bout the unit during install..... those nuts are a pain in the butt
hello, i bought this printer and it works but i can not save the values it finds with the auto level, i do as in the video but nothing to do ...
Have you tried running a serial connection to the printer using a slicing software? Common Marlin Mcodes may help out with that. M500 For example is save all current settings, M503 Is view all current Settings.
Thanks for the answer bro, i solved, probbaly it was the firmware!
do not buy from this company the customer support is bad and they will not send me a new printer
Yonas mesikir Their support is awesome. You probably just don't wanna work on fixing the printer. A DIY printer is always going to need more work
The customer support I got was great!