Absolutely brilliant! And for those of use whose partner continues to insist that our workshop be able to fulfill its secondary function as a garage for their car, this type of "portable" MFT bench could be just the thing since it can be knocked down and hung on cleats on the wall when bringing our partners precious steel baby in out of the weather. And once the cars are pulled out, the bench can be rapidly setup for getting down to the real use for a space large enough to park two cars indoors and that is to build furniture! And since I wouldn't have to "port" this bench more than a half dozen meters or so, it could be a bit bigger if I wanted with a rail hinge and a front apron with either T-slots or dog holes. Plus if I put some type of caster on the legs and a couple of sections of French cleat on the back of the bench top, I could roll it over to the wall, and tip it up so the cleats engage their mates on the wall. Throw a latch at the top to hold it flat against the wall, a quick fold of the legs, and my workshop would be ready to receive her overnight guests.
I noticed that - its like a continuation error but one where it didnt provide closure for the viewers brain! 😂 even the shot of the van outside didnt show the rear doors. 😫😁 all good. Im over it now though. 😆👍
You might put a round magnet on that cubby hole top. and hot glue another magnet on the bottom of a box to hold screws and such. Then later you can pull out the box, put the lid back on and it holds your box of screws handy. Plastic lid on the box. Or you could get fancy and make a wood box.
Also…I always found that customers were impressed whenever you use something like that. I had something similar but not as posh. I did some work for a policeman once who was fascinated with the racking set up in my van. He recommended me to a colleague who knew all about my van when I got there!😂
Very nicely done Peter 😁. I'm trying not to repeat the previous 400 comments... but... that is a thing of beauty 😁. Extremely well thought out and executed. Top job. It just needs a 10 minute logo cnc'd in to it to make it perfect 😁. Thanks for the video Peter.... now go and lock your van 😂🤣😁👍.
Outstanding video! Start with problem, show the solution and then follow up with clear demonstration of how to build the final product and finally tips on how to use it. If only all practical RUclips videos were the same. Great inspirational design, I've already started putting pencil to paper to design my own. Thanks Peter. Can't count how many hours I've wasted watching videos named 'Essential Must Have Tool', that start with someone sawing a log, only to get to the end to find they've created a Mongolian Candle Snuffer! 😬
You just gave me an idea, if we use magnets for the folding track hinge, make a grid of magnetic dog holes around the edges of the table, with magnetic dogs on the track hinge. Giving you lighting fast and accurate ways to line up your track perfectly. Even maybe chamfer the edges of the outter dog holes to allow them to guide the dogs in with fussing with trying to line it up to fit perfectly.
Hi Peter, I’m just finishing up my workbench, after following your plans that I purchased. Made a couple of mistakes, as we all do occasionally:-), but getting there now. Unfortunately I had to make mine out of the cheaper hardwood ply you can get from B&Q, which although it does the job, isn’t great quality. The only issue I have come across with that, is that once the legs were constructed, and the table is stood up, there is a lot more flex in the ply, so you get some flex rocking if using the bench to hand sand. Otherwise, I’m reasonably pleased with my first attempt. Many thanks for the great design.
Cheers Steve. Yes, anything with folding legs will have a bit of ‘wracking’ like that. When I was first designing it I tried a couple of drop-down stays that helped stabilise the legs - might be worth a try??
Peter I’m so glad you posted this. You are a great asset for RUclips viewers like me. I’m in California but we still have issues like upstairs jobs much of the time. Mostly 2 story houses and condos here. I’m always looking for best options for work surfaces. I love the sys mft boxes. But this idea is very useful. You may see it on my channel in the future. Glad I subscribed to you way back when. After I saw your videos on cordless paint sprayer. Brilliant.
Thanks David - you have a great channnel! If you wanted to keep the weight down you could forget about the legs and use trestles. Then you could cut down the frame, reduce weight there too.
@@10MinuteWorkshop thank you for your kind words regarding my Channel. And thank You so much for the sub. I am so appreciative. I’ll think about your ideas about the weight. Great idea. You do such a great job with your video editing. By the way.
The 4x8 Paulk is in two sections. If I didn't already have a 2x8 maple cabinet bench I would go for a 2x8 by itself, as it works well for me. Looking forward to your take.
Bought the plans, enjoyed the build, didn't enjoy forking out a small fortune for the birch ply! My bench is very nearly finished and I'm very pleased with the result. One thing I'm scratching my head about is when I fold the legs in they overlap in the middle. I've double checked all measurements and they appear correct - leg length 665mm, bench height 750mm, overall bench length 1438mm, legs right up against the end edges. Can't for the life of me what I've done wrong. I suppose I could trim them but I'd loose about 15mm height. The only thing I can think of is the hinges lay differently.
In addition to leaving your van doors open, when you came inside your workshop and sat down, the label on the window that you obfuscated on the outside was clearly legible on the reverse.
Googling the first two lines brings up lots of stuff including Google maps and trade website listings for his business. One of them is Peter's squarespace website which has this address in the footer of every page so I guess he is pretty chill about leaking this info. More mysterious is why the front was blurred given this.
Great video Peter. Congratulations on finally completing a great build. I think this Mick guy is going to be very busy with orders. And he offers the sacrificial strip as well. Good in him.
@@10MinuteWorkshop. Well, once the shop is up & running & after insulation, wall coverings & paint, I will build the framework & then ask Mick if he can do to exact dimensions for the mft top. This could be a very exciting early Xmas present. Have a great weekend Peter & speak soon. G
This is not a "good idea or proof of concept" What it is a well thought out design equally well built and a ultimatley a finished product, can't wait to see version 1.01 and beyond Great work Peter
Nice design, glad you addressed the weight issue I couldn't help but chuckle as you were moving it about (panting) but you fitted everything you need into it, which is the point of a custom table, good work (Wheels Peter wheels)
Thanks Ray! Yep, if you don’t need the ‘all in one’ approach then you could reduce the depth of the frame to ~75mm or so and still keep the end cubbies, and have the frame notched for the trestles. I don’t like working off trestles personally, as I always find I need to move the damn thing, but that’s just me! 😂👍👍🤷♂️
I can tell the extra effort going into the fliming aspect now that you stopped your day job peter. Great work. Either that or you've hired a film crew. Also, maybe route in a shallow magnetic dish into the right hand side to keep screws together whilst working on something.
Weight. Always the PITA for us. I built something very similar, out of mahogany, same folding leg hardware. But it's a bit shorter and longer and a wee bit narrower - for holding my astronomy kit while at a dark sky site. I think I was allowed to use it once or twice for that then the wife requisitioned. sign. Now it's a printer and lamp stand in the living room. I like cubby holes you did. Nice touch.
Great build Peter, looks a really useful bench for a trade user. For myself in the garage, the more I see on all the mft tops, bench dogs, and rail squares I'm thinking this is probably now something I need 😁😔😬
I find the MFT’s limitation is its wobblieness under heavy use like planing and heavy chiseling. That said, a number of years ago I made a simple cutting/work surface about this same size for making trim and other small cuts for indoor use, which is a huge time-saver over running back outside every time I needed to make a quick cut at the chopsaw. Mine is a simple, bit of MDF on a flat frame - no legs, made for use directly on the floor/ground (size and weight reasons). Peter’s version is a great conclusion to my extremely basic solution! His fold away legs are light and compact, yet allow it to be used low on the ground (very helpful in remodel situations) AND the legs enable that extremely helpful shelf plus guide rail stowage. And then his solution includes all those other extremely well conceived features. Great project tool Peter, thanks for sharing it!
I have almost finished building it from the plans I purchased. With just a couple of changes to get the workbench taller. The plans are fab. Easy to follow and well worth the money.
@@10MinuteWorkshop here's a link to them hope that's ok remove this if it's not. I did the 1400 top so no cubbies. That ment I could offset the heights of the legs so one fits under the under. photos.app.goo.gl/bwdWTRQxEQLBGeSn9
@@timrawlings1511 Looks fantastic, thanks Tim! If you have any final photos of the bench standing, I’d love to post them to Instagram - if that’s OK with you of course. Or if you’re on Instagram yourself then I’ll repost, if you let me know you’re username. Thanks! 👍
@@10MinuteWorkshop I will do I don't do Instagram feel free to post them. Waiting for bits from Amazon to finish it and free time I will get back to you with finished picture s problely next week
Wow Peter , love it , i was thinking ,two of those and a bridgeing infill and you would have a full joiners bench . I have had occasions where i had to make bespoke windows on site . In Sandgate high st , i worked on a church conversions , one of the four units became a dedicated work shop ( with overnight security of course ) i had to make gothic arch windows , bullseye windows and the exterior door frame with side light window . I was in 7th heaven , i did the job about 18yrs ago . I undercoated all the woodwork in metallic primer , as the building is on the seafront.
I’m super impressed by what you made. There are quite a few “why didn’t I think of that” moments. The front lip would have saved me. But that release wire? Now I won’t feel like I’m picking a lock every time I need 2 legs to collapse at the same time.
Peter, I just had a wild idea regarding making the bench more portable. How about a detachable two wheeled dolly that goes on one end? Think of a hand truck. The wheels could be any size but the bigger they are the easier to negotiate rough roads and if big enough, you could more easily take it up stairs. Seems to me the the two wheels would be on a short axle that would fit into grooves, slots or some way attach to the bench and then detach just as easily when you have arrived at your destination. You would of course steer from the end without the wheels and he wheels would go on the narrow side of the bench. IE, if your bench is 600mm wide and the part directly below the top is say 200mm deep, then the wheels go on the 200mm part. The part where you have the guide rail stored is what I am referencing.
Thanks! Yes, all kinds of options - I think I mention in the video that if you routinely need to park away from the site then a small dolly could be useful. 👍👍
Yes Tsch Tscht Tisckt you left your van doors wide open. Glad I was not the only one who noticed. All kidding aside, I do like this design as most of us do not need a full Paulk bench or work table and really don't have the space for it. As you point out, Scott Brown's design is more portable but still thick and a bit unwieldy . Your design was clearly conceived by a cabinet maker. so it is very refined . Love the cubbies. My fave thing about the design is the thickness profile. This can easily be hung on a garage wall and lifted into action quite easily. I would only need to perhaps flip the under table upside down so it has some sort of edges to prevent things from falling off the lower shelf. I might beef that up a bit for more tools to be held in place. Seeing as not ALL my tools are cordless I probably would install some sort of electrical strip to plug things into ...especially battery chargers.... mind you today the batteries are 4-5ah and can last a very long time especially for DIYers. In all this concept bench does resolve alot of design issues and space issues for me and will probably be the basis for my own take on a hangable table that can also fit in normal SUVs. Cheers and Peter please do shut those van doors next time..
Haha - No I Didn’t! 😂😂 Yes, the beauty of this being all plywood is that these kinds of changes and adaptations are easily made - much harder to do if it was an aluminium framework! 👍👍
@@10MinuteWorkshop The only challenge are those pesky bench dog holes and pegs.... not so easy to source here in Canada. I think there's some kits to create them but then once you're done the kit will sit there collecting dust unless you plan on making MFT tables for everyone you know.
Very nice! You can consider poplar or sika ply is the weight is an issue! What I like most is the simplicity of the build and the economics of the wood utilization, not like some “Californian” dude out there with his self proponte infomercial videos. Love the content Peter, never disappointedT Thank you 🙏
Peter always a pleasure to tune, I particularly love the statement of making a work bench that fits your needs. I have bought plenty of benches but they don't quite fit what I need. I think the bench I need is a Frankinbench.
Watching your videos has given me a renewed interest and also spurred me on to create my own 'portable' mft workbench based around Stanley sawhorses. I had contacted Mick at Cnc formattics (not realising they no longer produced them) before Xmas, but heard nothing, so ended up getting one from Lasersmith in Scotland. Anyway, thanks Peter. 👍🏻👍🏻
Very nice Peter. One change I would do for myself because I would want to have more things in the storage compartments. I would have them removable so I would not have it weighing to much for me to carry with all the things I would have stored in them. I would have the peanut fittings on the storage compartments to attach to the bench. The two storage compartments would be attached to each other. Thank you for the great idea. I have been wanting to make one for a while & I like yours the best compared to the others out there. Thanks again Peter for your great videos & all the time you put into them
Thanks John! That’s a really good idea, and that’s the beauty of something like this. Because it’s made of plywood not aluminium, then it’s easy to adapt to your needs or requirements! 👍👍
Another awesome shop video. 👍 I built a Paulk style bench for my shop but it became a permanent fixture. I agree it’s only a portable design if you’re determined enough to force it to be. 😀 your design is quite nice.
Peter, Nice job, looks very interesting. Yes I took up the plans for the wheeled MFTC and also never got around to it. Looked at the Stanton Bench, which sits on the top of a work top or table, not so good on the Walnut dinning table. I designed my own based on using a pair of metal saw horses with wood beams between, then 2 or 4 panels that join together for a the top with an apron like the Stanton Bench. I think your design is simple, light-ish but certainly simple to slide in the van or estate car. To set up and get to work is simple. Great Job.
Thanks Barry! Yes, I’m nit a fan of worktops on trestles personally - I find I need to move the bench around - but separating out the legs would make things much simpler and lighter. Just not really my thing. 👍👍
Thanks! Honestly, couldn’t believe it - it had been a beautiful day the day before, but it was so Misty in the day I had time to shoot it! 🤷♂️ At least it was atmospheric! 😆😂😂
Great portable bench Peter, I’m retired now, but if I was still doing service calls I wouldn’t be writing this, I’d be out in the shop making one. Great job have a great weekend
Fantastic! This is just the design I've been looking for and haven't got round to (or don't have the skills to) design myself. I'm sure I'll be making one of these at some point. Thank you.
Peter why not put additional holes in the top and the plywood case to to lighten it up even the legs could probably take some lightening holes and still be sturdy. Everything helps.
Glad I'm not the only one that thinks the Paulk bench is ridiculous for a 'mobile' thing. More of semi mobile. Smart guy I assume but never actually see any use of everything he builds. Every other wood channel show their stuff in use. Him not so much. Just always showing how it's 'smart' Really like the bench though Peter. Simple design but effective
Nice bench Peter. Something you might consider is adding 2 more handles one on each end. That way, just in case there are two of you on the jobsite, then lifting this thing up narrow stairs or a long hike away would be easier with two people.
Hello I thought of two things to improve the bench. The first is that you can put any kind of wheel on one short side to make it easier to transport the bench? When you watch the video, it seems quite heavy. The second is that you could put wheels on the legs as well or make the lower shelf so that it prevents? This makes the bench itself easier to transport and move when working.
Hi Jan, and thanks! I do mention a wheel-set or trolley in the video. Not a fan of wheels on legs, personally, but that's mostly because I rarely work on even ground! 👍
Brilliant Peter, It was only this morning I was thinking about making some sort of template for an MFT for folks to buy but CNC beats it hands down. Great video. Thanks for all your time and thought given over to this. I’m hoping I never need to buy a table saw. 👏👏
Well, that's just bloody ridiculously good. A colleague and I have to fit some worktops where I work with no workshop space, this or something very similar is about to be made!
Hi Peter , another great video , thanks for sharing , I absolutely love your attention to detail , one thing I have learned from watching your channel is when you can make up small jigs and templates out of your leftover material , this ensures for perfect joins and sizing and it’s costs you nothing , awesome table
Great video as always Peter and this is exactly what I have been looking for. I am rubbish DIYer / wanna-be-woodworker but I have no garage or shed to setup a workshop. So usually work in the back lane of my house during the summer on a wee project. but my setup lacks precision. This table top with an entry level plunge saw maybe what I need to allow for better quality project outcomes. Thanks again
Great video, I ordered a top from the new link you posted and highly recommended him. Delivery was super quick and excellent quality. Great video, really enjoy these.
I have been reluctant to put an MFT in my shop due to space limitations. This workbench completely changes that equation. I am going to see if such a bench would work in my shop.
Thats looks just the job for my new garage. I've got too many hobbies so it has to be a car workshop, a motorbike work shop, a bicycle workshop and also a woodshop, all in a 7x5m garage! This will allow me to pull out and pack away when ever I need to. It also poses a problem of needing a bench to build a bench, but I haven't got a bench, and so it goes round and round. I guess I'll be making it on the floor then! I'm off to your Etsy shop to get the plans! Thanks!
Ok. So I just commented on another video of yours about my domino and how I wanted the MFT3. And as I started watching this I thought this would be a great workbench for me to set up when I use my domino to clamp things down. But using that square and other rail..... That could come in REALLY handy. Off to go watch those videos.
1400 width instead of 1200 may give you the capacity to process 4ft wide sheets probably. Its 1st video of yours where I felt much more can be done on this. I have learned much from you
Brilliant!! I imagine those cubby lids and sacrificial strip could work loose over time/repeated use. Might I suggest rare earth magnets to help secure them. Great vid. Forever a fan.
Thanks! Yea to the sacrificial strip - but it’s sacrificial, I’ll just make another. And no, the cubby lids are fixed with Buttonfix fixings, they’re super-strong! 👍👍
Unfortunately the comnpany mentioned in this video (Formatic CNC) appear to have stopped making MFT tops. Many other companies make MFT-style tops to order, or you can adapt an off-the-shelf MFT 1080 top (1080 1165 x 725) or MFT/3 top (1102 x 718) to fit. Or make your own, of course, with one of the many commercial jigs available. 👍
thats a bummer because i ordered one off them on the 9th of this month and am still waiting for it. thought it might have been with me by now to be honest. really hope i dont have to start any sort of process to get my money back off them. if only i had know this before i ordered.
just wanted to update this with the outcome. i sent an email asking when my order would be dispatched and waited. 4 days later i got a email back simply saying that a refund had been issued and would be in my bank soon. nothing else. no explanation or anything. all it said was "Your order from Formatic CNC has been refunded." A simple 'Sorry' would have been nice... but i suppose at least i got an easy refund. I then went to ebay and ordered a top from there. 3 days later its sat in my living room waiting to be fitted..................Now im happy !!
![Backyard, DIY MFT on a Budget [video 490]](http://i.ytimg.com/vi/xIi-I04ocVM/mqdefault.jpg)
![Backyard, DIY MFT on a Budget [video 490]](/img/tr.png)
![Eminem - Somebody Save Me (feat. Jelly Roll) [Official Music Video]](http://i.ytimg.com/vi/Vwa0HenQMi4/mqdefault.jpg)
Absolutely brilliant! And for those of use whose partner continues to insist that our workshop be able to fulfill its secondary function as a garage for their car, this type of "portable" MFT bench could be just the thing since it can be knocked down and hung on cleats on the wall when bringing our partners precious steel baby in out of the weather. And once the cars are pulled out, the bench can be rapidly setup for getting down to the real use for a space large enough to park two cars indoors and that is to build furniture!
And since I wouldn't have to "port" this bench more than a half dozen meters or so, it could be a bit bigger if I wanted with a rail hinge and a front apron with either T-slots or dog holes. Plus if I put some type of caster on the legs and a couple of sections of French cleat on the back of the bench top, I could roll it over to the wall, and tip it up so the cleats engage their mates on the wall. Throw a latch at the top to hold it flat against the wall, a quick fold of the legs, and my workshop would be ready to receive her overnight guests.
Hi Peter, this will almost positively be too late but you have left your van with the doors wide open and all your tools inside.
Not any more they’re Not! 😂👍
Totally the only thing I could think about the whole time 😂
No one's allowed outside so it's ok
Door are still open and there’s no longer any tools in it? :p
I noticed that - its like a continuation error but one where it didnt provide closure for the viewers brain! 😂 even the shot of the van outside didnt show the rear doors. 😫😁 all good. Im over it now though. 😆👍
You might put a round magnet on that cubby hole top. and hot glue another magnet on the bottom of a box to hold screws and such. Then later you can pull out the box, put the lid back on and it holds your box of screws handy. Plastic lid on the box. Or you could get fancy and make a wood box.
Also…I always found that customers were impressed whenever you use something like that. I had something similar but not as posh. I did some work for a policeman once who was fascinated with the racking set up in my van. He recommended me to a colleague who knew all about my van when I got there!😂
It’s the little things! 😆👍
Very nicely done Peter 😁. I'm trying not to repeat the previous 400 comments... but... that is a thing of beauty 😁. Extremely well thought out and executed. Top job. It just needs a 10 minute logo cnc'd in to it to make it perfect 😁. Thanks for the video Peter.... now go and lock your van 😂🤣😁👍.
Thanks Frank! Duh! Missed a trick with the logo - don’t think of that! 😂 👍👍
Outstanding video! Start with problem, show the solution and then follow up with clear demonstration of how to build the final product and finally tips on how to use it.
If only all practical RUclips videos were the same. Great inspirational design, I've already started putting pencil to paper to design my own. Thanks Peter.
Can't count how many hours I've wasted watching videos named 'Essential Must Have Tool', that start with someone sawing a log, only to get to the end to find they've created a Mongolian Candle Snuffer! 😬
Thank you! But damn - there goes my ‘Essential must-have bench accessories’ video! 🤷♂️😂😂👍👍
The Professor of the small workshop does it again ,Its a great build Peter ,well done !!!
Thanks Adrian! 😆👍👍
You just gave me an idea, if we use magnets for the folding track hinge, make a grid of magnetic dog holes around the edges of the table, with magnetic dogs on the track hinge. Giving you lighting fast and accurate ways to line up your track perfectly. Even maybe chamfer the edges of the outter dog holes to allow them to guide the dogs in with fussing with trying to line it up to fit perfectly.
Excellent. Well done Peter.
Thanks Nico! 👍
Hi Peter, I’m just finishing up my workbench, after following your plans that I purchased. Made a couple of mistakes, as we all do occasionally:-), but getting there now. Unfortunately I had to make mine out of the cheaper hardwood ply you can get from B&Q, which although it does the job, isn’t great quality. The only issue I have come across with that, is that once the legs were constructed, and the table is stood up, there is a lot more flex in the ply, so you get some flex rocking if using the bench to hand sand. Otherwise, I’m reasonably pleased with my first attempt. Many thanks for the great design.
Cheers Steve. Yes, anything with folding legs will have a bit of ‘wracking’ like that. When I was first designing it I tried a couple of drop-down stays that helped stabilise the legs - might be worth a try??
@@10MinuteWorkshop thanks Peter, didn’t think of that 👍. I’ll see how I go, it’s not a major problem at the moment. Many thanks.
Well thought out! The only think I would add is a removable wheel set on one corner to help in transporting. Thanks Peter!
Thanks! Yes, that’s always an option, or a skateboard-style dolly. 👍👍
Peter I’m so glad you posted this. You are a great asset for RUclips viewers like me. I’m in California but we still have issues like upstairs jobs much of the time. Mostly 2 story houses and condos here. I’m always looking for best options for work surfaces. I love the sys mft boxes. But this idea is very useful. You may see it on my channel in the future. Glad I subscribed to you way back when. After I saw your videos on cordless paint sprayer. Brilliant.
Thanks David - you have a great channnel! If you wanted to keep the weight down you could forget about the legs and use trestles. Then you could cut down the frame, reduce weight there too.
@@10MinuteWorkshop thank you for your kind words regarding my Channel. And thank You so much for the sub. I am so appreciative. I’ll think about your ideas about the weight. Great idea. You do such a great job with your video editing. By the way.
Simply brilliant Peter.
Thank you! 👍👍
looks very nice
Thank you!
The 4x8 Paulk is in two sections. If I didn't already have a 2x8 maple cabinet bench I would go for a 2x8 by itself, as it works well for me. Looking forward to your take.
Bought the plans, enjoyed the build, didn't enjoy forking out a small fortune for the birch ply! My bench is very nearly finished and I'm very pleased with the result. One thing I'm scratching my head about is when I fold the legs in they overlap in the middle. I've double checked all measurements and they appear correct - leg length 665mm, bench height 750mm, overall bench length 1438mm, legs right up against the end edges. Can't for the life of me what I've done wrong. I suppose I could trim them but I'd loose about 15mm height. The only thing I can think of is the hinges lay differently.
In addition to leaving your van doors open, when you came inside your workshop and sat down, the label on the window that you obfuscated on the outside was clearly legible on the reverse.
Googling the first two lines brings up lots of stuff including Google maps and trade website listings for his business. One of them is Peter's squarespace website which has this address in the footer of every page so I guess he is pretty chill about leaking this info. More mysterious is why the front was blurred given this.
This is the first time I've ever seen a fence like that, for a MFT. So awesome!!
Great video Peter. Congratulations on finally completing a great build. I think this Mick guy is going to be very busy with orders. And he offers the sacrificial strip as well. Good in him.
Cheers Gary! Yes, I hope Mick is kept busy - don’t know how it does it for the money tbh. 🤷♂️👍
@@10MinuteWorkshop. Well, once the shop is up & running & after insulation, wall coverings & paint, I will build the framework & then ask Mick if he can do to exact dimensions for the mft top. This could be a very exciting early Xmas present. Have a great weekend Peter & speak soon. G
This is not a "good idea or proof of concept" What it is a well thought out design equally well built and a ultimatley a finished product, can't wait to see version 1.01 and beyond
Great work Peter
Thanks! Yes, there’ll be an update or two on this, I think! 👍👍
Your best video yet! You have completely changed my design idea for my bench top. This is better than an MFT!
Thanks Mark! And wow! 😆👍👍
Nice design, glad you addressed the weight issue I couldn't help but chuckle as you were moving it about (panting) but you fitted everything you need into it, which is the point of a custom table, good work (Wheels Peter wheels)
This could be the solution for me, I have some Stanley work horses so could adapt this design to use those as the legs. Great video.
Thanks Ray! Yep, if you don’t need the ‘all in one’ approach then you could reduce the depth of the frame to ~75mm or so and still keep the end cubbies, and have the frame notched for the trestles. I don’t like working off trestles personally, as I always find I need to move the damn thing, but that’s just me! 😂👍👍🤷♂️
I can tell the extra effort going into the fliming aspect now that you stopped your day job peter. Great work. Either that or you've hired a film crew. Also, maybe route in a shallow magnetic dish into the right hand side to keep screws together whilst working on something.
Thanks! Ooo magnets! Hadn’t thought of magnets - you could recess them into the underside! Nice one, thanks! 👌👍👍
Thanks Peter, I've just ordered an MFT from Formatic-CNC.
Nice! 👍👌💪
Hi Peter not spoken for a while. I spent the entire video worrying about your van with the back doors open. Good to see you’re still at it! Graham.
Here’s Graham! 👍👍
brilliant idea made well could be the best thing since the old black and decker work mate well done
Thank you! 👍
Weight. Always the PITA for us. I built something very similar, out of mahogany, same folding leg hardware. But it's a bit shorter and longer and a wee bit narrower - for holding my astronomy kit while at a dark sky site. I think I was allowed to use it once or twice for that then the wife requisitioned. sign. Now it's a printer and lamp stand in the living room. I like cubby holes you did. Nice touch.
Yep. Yours sounds nice - even if the Mrs has taken it off your hands! 🤷♂️👍
Great build Peter, looks a really useful bench for a trade user. For myself in the garage, the more I see on all the mft tops, bench dogs, and rail squares I'm thinking this is probably now something I need 😁😔😬
Cheers James! Ha. There are always more things to buy! 😆👍👍
I find the MFT’s limitation is its wobblieness under heavy use like planing and heavy chiseling.
That said, a number of years ago I made a simple cutting/work surface about this same size for making trim and other small cuts for indoor use, which is a huge time-saver over running back outside every time I needed to make a quick cut at the chopsaw. Mine is a simple, bit of MDF on a flat frame - no legs, made for use directly on the floor/ground (size and weight reasons).
Peter’s version is a great conclusion to my extremely basic solution! His fold away legs are light and compact, yet allow it to be used low on the ground (very helpful in remodel situations) AND the legs enable that extremely helpful shelf plus guide rail stowage. And then his solution includes all those other extremely well conceived features.
Great project tool Peter, thanks for sharing it!
A possible alternative to recessing a tray would be to set a few magnets into the underside of the top.
Way to go Peter love your videos! All the best from Sweden.
Thank you! And best wishes from London! 👍👍
I have almost finished building it from the plans I purchased. With just a couple of changes to get the workbench taller. The plans are fab. Easy to follow and well worth the money.
Thanks Tim! Sounds great; how did you raise the height - staggered legs? Show me some pictures when you’re done, OK? 👍👍
@@10MinuteWorkshop here's a link to them hope that's ok remove this if it's not. I did the 1400 top so no cubbies. That ment I could offset the heights of the legs so one fits under the under. photos.app.goo.gl/bwdWTRQxEQLBGeSn9
@@timrawlings1511 Looks fantastic, thanks Tim! If you have any final photos of the bench standing, I’d love to post them to Instagram - if that’s OK with you of course. Or if you’re on Instagram yourself then I’ll repost, if you let me know you’re username. Thanks! 👍
@@10MinuteWorkshop I will do I don't do Instagram feel free to post them. Waiting for bits from Amazon to finish it and free time I will get back to you with finished picture s problely next week
@@timrawlings1511 Thanks Tim! 👍
Wow Peter , love it , i was thinking ,two of those and a bridgeing infill and you would have a full joiners bench . I have had occasions where i had to make bespoke windows on site .
In Sandgate high st , i worked on a church conversions , one of the four units became a dedicated work shop ( with overnight security of course ) i had to make gothic arch windows , bullseye windows and the exterior door frame with side light window . I was in 7th heaven , i did the job about 18yrs ago . I undercoated all the woodwork in metallic primer , as the building is on the seafront.
Thanks! Wow, sounds like a heck of a job. 🙌👍👍
That was slick but you said about the wobbly floor. That was really good I'll have to use that one.
I hope you, and your family, are doing well, Peter
Yes, well tanks Matthew! Hope you and yours are the same. 👍👍
I’m super impressed by what you made. There are quite a few “why didn’t I think of that” moments. The front lip would have saved me. But that release wire? Now I won’t feel like I’m picking a lock every time I need 2 legs to collapse at the same time.
Thanks! Yes, those release catches always call for a third hand! 😂👍
Peter, I just had a wild idea regarding making the bench more portable. How about a detachable two wheeled dolly that goes on one end? Think of a hand truck. The wheels could be any size but the bigger they are the easier to negotiate rough roads and if big enough, you could more easily take it up stairs. Seems to me the the two wheels would be on a short axle that would fit into grooves, slots or some way attach to the bench and then detach just as easily when you have arrived at your destination. You would of course steer from the end without the wheels and he wheels would go on the narrow side of the bench. IE, if your bench is 600mm wide and the part directly below the top is say 200mm deep, then the wheels go on the 200mm part. The part where you have the guide rail stored is what I am referencing.
Thanks! Yes, all kinds of options - I think I mention in the video that if you routinely need to park away from the site then a small dolly could be useful. 👍👍
Now, that's smart. Your videos are among the few worth playing @ 1 X speed. Thank you.
Haha - compliment of the day, thanks! 👍👍😂
Yes Tsch Tscht Tisckt you left your van doors wide open. Glad I was not the only one who noticed. All kidding aside, I do like this design as most of us do not need a full Paulk bench or work table and really don't have the space for it. As you point out, Scott Brown's design is more portable but still thick and a bit unwieldy . Your design was clearly conceived by a cabinet maker. so it is very refined . Love the cubbies. My fave thing about the design is the thickness profile. This can easily be hung on a garage wall and lifted into action quite easily. I would only need to perhaps flip the under table upside down so it has some sort of edges to prevent things from falling off the lower shelf. I might beef that up a bit for more tools to be held in place. Seeing as not ALL my tools are cordless I probably would install some sort of electrical strip to plug things into ...especially battery chargers.... mind you today the batteries are 4-5ah and can last a very long time especially for DIYers. In all this concept bench does resolve alot of design issues and space issues for me and will probably be the basis for my own take on a hangable table that can also fit in normal SUVs. Cheers and Peter please do shut those van doors next time..
Haha - No I Didn’t! 😂😂 Yes, the beauty of this being all plywood is that these kinds of changes and adaptations are easily made - much harder to do if it was an aluminium framework! 👍👍
@@10MinuteWorkshop The only challenge are those pesky bench dog holes and pegs.... not so easy to source here in Canada. I think there's some kits to create them but then once you're done the kit will sit there collecting dust unless you plan on making MFT tables for everyone you know.
I’m pretty sure Benchdogs.co.uk shop globally, but you can always shoot them an email and ask. Don’t forget the offer code for 5% discount! 👍👍
Nicely done, all the extra hardware gives it good functionality 👍🏻👍🏻😎😎
Thanks! Yes - it’s not a bad bench as it is, but the hardware makes the difference. 👍👍
Very Nice. Thanks for the great ideas and video.
Thanks! 👍
Great as always. It’s pretty interesting you measure so often in mm and here also kg. 👍
👍👍
It’s the French metric system. As everyone knows, here in England we love all things french.
Very nice! You can consider poplar or sika ply is the weight is an issue! What I like most is the simplicity of the build and the economics of the wood utilization, not like some “Californian” dude out there with his self proponte infomercial videos. Love the content Peter, never disappointedT Thank you 🙏
Thanks Jose! Yes, I wanted to try poplar ply, but couldn’t get any in time. It would make a big difference I’m sure! 👍👍
Peter always a pleasure to tune, I particularly love the statement of making a work bench that fits your needs. I have bought plenty of benches but they don't quite fit what I need. I think the bench I need is a Frankinbench.
Oh yes - well familiar with the 'Franken**' school of construction! 😂
Peter it’s obviously had a lot of thought! Very well done and it will serve you well for along time. Cheers
Watching your videos has given me a renewed interest and also spurred me on to create my own 'portable' mft workbench based around Stanley sawhorses. I had contacted Mick at Cnc formattics (not realising they no longer produced them) before Xmas, but heard nothing, so ended up getting one from Lasersmith in Scotland. Anyway, thanks Peter. 👍🏻👍🏻
Very nice Peter. One change I would do for myself because I would want to have more things in the storage compartments. I would have them removable so I would not have it weighing to much for me to carry with all the things I would have stored in them. I would have the peanut fittings on the storage compartments to attach to the bench. The two storage compartments would be attached to each other. Thank you for the great idea. I have been wanting to make one for a while & I like yours the best compared to the others out there. Thanks again Peter for your great videos & all the time you put into them
Thanks John! That’s a really good idea, and that’s the beauty of something like this. Because it’s made of plywood not aluminium, then it’s easy to adapt to your needs or requirements! 👍👍
Another awesome shop video. 👍 I built a Paulk style bench for my shop but it became a permanent fixture. I agree it’s only a portable design if you’re determined enough to force it to be. 😀 your design is quite nice.
Thanks! Paulk bench is great if you have the space. 👍👍
Super nice design! Simple, practical, and very usable. These types of builds always take the most planning. Best way to go!
Thanks! 👍
Peter, Nice job, looks very interesting. Yes I took up the plans for the wheeled MFTC and also never got around to it. Looked at the Stanton Bench, which sits on the top of a work top or table, not so good on the Walnut dinning table. I designed my own based on using a pair of metal saw horses with wood beams between, then 2 or 4 panels that join together for a the top with an apron like the Stanton Bench.
I think your design is simple, light-ish but certainly simple to slide in the van or estate car. To set up and get to work is simple. Great Job.
Thanks Barry! Yes, I’m nit a fan of worktops on trestles personally - I find I need to move the bench around - but separating out the legs would make things much simpler and lighter. Just not really my thing. 👍👍
Absolute genius design !! Thanks so much Peter.
Thanks, glad you like it! 👍
Very nice and looks really handy. Oh I do love the morning fog.
Thanks! Honestly, couldn’t believe it - it had been a beautiful day the day before, but it was so Misty in the day I had time to shoot it! 🤷♂️ At least it was atmospheric! 😆😂😂
This is brilliant! You really have thought of everything!
Thank you! Critics might say that I’ve had plenty of time to be thinking about it! 😂👍
Great portable bench Peter, I’m retired now, but if I was still doing service calls I wouldn’t be writing this, I’d be out in the shop making one. Great job have a great weekend
Thanks! Good weekend to you too! 👍
Fantastic work. Really looks like it’s been worth the effort
Thanks! Yes - plenty of thinking time! 😂👍
Fantastic! This is just the design I've been looking for and haven't got round to (or don't have the skills to) design myself. I'm sure I'll be making one of these at some point. Thank you.
Thanks! Let me know how you get on! 👍👍
Beware saw horse can go for a gallop. Some have a lot of movement and having tried them, think Peter's self contained legs, like Ron Paulk's work.
Peter why not put additional holes in the top and the plywood case to to lighten it up even the legs could probably take some lightening holes and still be sturdy. Everything helps.
Thanks! Ultralight bench coming soon! 👍👍
Glad I'm not the only one that thinks the Paulk bench is ridiculous for a 'mobile' thing. More of semi mobile.
Smart guy I assume but never actually see any use of everything he builds. Every other wood channel show their stuff in use. Him not so much. Just always showing how it's 'smart'
Really like the bench though Peter. Simple design but effective
Nice bench Peter. Something you might consider is adding 2 more handles one on each end. That way, just in case there are two of you on the jobsite, then lifting this thing up narrow stairs or a long hike away would be easier with two people.
Thanks! Yes, good idea! 👍👍
Love the bench. You could put some fixed castors at one end and a handle at the other. Then it would be able to be dragged rather then carried
👍👍
Functional and looks good, cant ask for more than that in a mobile work bench.
Thanks! 👍
Hello
I thought of two things to improve the bench.
The first is that you can put any kind of wheel on one short side to make it easier to transport the bench? When you watch the video, it seems quite heavy.
The second is that you could put wheels on the legs as well or make the lower shelf so that it prevents?
This makes the bench itself easier to transport and move when working.
Hi Jan, and thanks! I do mention a wheel-set or trolley in the video. Not a fan of wheels on legs, personally, but that's mostly because I rarely work on even ground! 👍
Me gusto mucho tu diseño y lo compacto que es para trasladar al trabajo. Gracias por la idea Peter.
¡Gracias! Mis mejores deseos desde Londres. 👍
Peter, excellent videos. Bought your bench dogs, stop block and rail. Wow! Thanks for your wealth of info.
Thanks! 👍
Brilliant Peter,
It was only this morning I was thinking about making some sort of template for an MFT for folks to buy but CNC beats it hands down. Great video. Thanks for all your time and thought given over to this. I’m hoping I never need to buy a table saw. 👏👏
Thank you! 👍
Your solution may have just changed my entire plan. Thank you so much Peter! I'm buying your plans and I feel I owe you a drink too.
Haha - hopefully changes in a good way! And mine’s a pint, thanks. 😂 🍻
Brilliant, ordered MFT top straight away.Plan to fix it to my workbench.Thanks!
Excellent, and thanks! 👍👍
Thanks
What a cracking piece of kit!👍👍👍👍👍👍👍👍👍😎
Cheers Alan! 👍👍
Very practical design Peter. Well thought out.
Cheers Stew! 👍👍
Well, that's just bloody ridiculously good. A colleague and I have to fit some worktops where I work with no workshop space, this or something very similar is about to be made!
Excellent! 👍👍
Fantastic compact design with everything needed on board! 👌🏽
Brilliant idea and awesome build, mate! 👍🏽
Cheers Bill! Been a long time coming, but happy it’s here - finally! 😂👍
Hi Peter , another great video , thanks for sharing , I absolutely love your attention to detail , one thing I have learned from watching your channel is when you can make up small jigs and templates out of your leftover material , this ensures for perfect joins and sizing and it’s costs you nothing , awesome table
Thanks! 👍👍
This is a brilliant design.
Thank you! 👍
I have a shop-made MFT but love this design. Simple yet still great features.
Thanks! 👍
Thankyou for sharing your video Peter, a very clever bench design.
Thanks Stuart! 👍
Great video as always Peter and this is exactly what I have been looking for. I am rubbish DIYer / wanna-be-woodworker but I have no garage or shed to setup a workshop. So usually work in the back lane of my house during the summer on a wee project. but my setup lacks precision. This table top with an entry level plunge saw maybe what I need to allow for better quality project outcomes. Thanks again
Thanks Colin! Let me know how you get on! 👍👍
Great idea Peter !
Nice bench could always add some threaded bolt legs if you have an uneven ground just a thought. Great videos!
Thanks! Yes, could do - the kegs are thick enough to take a fat threaded foot. Maybe there’ll be a bench Mk2! 😂👍👍
Ahhhh finally the long awaited master piece. Looks great!!👌🥳
Maybe a bit heavy but in any case solid. Love the self-locking feet!
Thanks! Yes, a bit heavier than I’d have liked. The Mk2 will be lighter! 😂👍
Very good video. I liked the longer format. You were able to explain everything.
Thanks Mike! Yes, sometimes you just have more to say. 🤷♂️👍👍
Great video, I ordered a top from the new link you posted and highly recommended him. Delivery was super quick and excellent quality.
Great video, really enjoy these.
I have been reluctant to put an MFT in my shop due to space limitations. This workbench completely changes that equation. I am going to see if such a bench would work in my shop.
👍👍
This is brilliant, I might adapt something like this to the Hooked on Wood bench I’ve been working on.
Go for it! 👍
Thats looks just the job for my new garage. I've got too many hobbies so it has to be a car workshop, a motorbike work shop, a bicycle workshop and also a woodshop, all in a 7x5m garage! This will allow me to pull out and pack away when ever I need to. It also poses a problem of needing a bench to build a bench, but I haven't got a bench, and so it goes round and round. I guess I'll be making it on the floor then! I'm off to your Etsy shop to get the plans! Thanks!
Thanks! 👍👍
Excellent design, congrats
I’m loving the portable bench
Thanks! 👍
Ok. So I just commented on another video of yours about my domino and how I wanted the MFT3. And as I started watching this I thought this would be a great workbench for me to set up when I use my domino to clamp things down. But using that square and other rail..... That could come in REALLY handy. Off to go watch those videos.
Do you have a link for the metal brackets? Or a searchable name for them?
Thanks! There are links to everything in the video description. 👍👍
Mobile kitchen bench for campervan!
1400 width instead of 1200 may give you the capacity to process 4ft wide sheets probably.
Its 1st video of yours where I felt much more can be done on this.
I have learned much from you
Thanks! 👍
Very clever design. Spot on.
Thank you! 👍
Well done - giving more to think about. Keep the ideas coming.
Thank you! 👍
Looks great. Love the editing as well. I fully respect your effort. No doubt a reflection of all your work!
Thank you! 🙌
The Tony Stark of portable benches!!
😂👍
This is beautiful work and forethought.
Thank you! 👍
Brilliant!! I imagine those cubby lids and sacrificial strip could work loose over time/repeated use. Might I suggest rare earth magnets to help secure them. Great vid. Forever a fan.
Thanks! Yea to the sacrificial strip - but it’s sacrificial, I’ll just make another. And no, the cubby lids are fixed with Buttonfix fixings, they’re super-strong! 👍👍
Unfortunately the comnpany mentioned in this video (Formatic CNC) appear to have stopped making MFT tops. Many other companies make MFT-style tops to order, or you can adapt an off-the-shelf MFT 1080 top (1080 1165 x 725) or MFT/3 top (1102 x 718) to fit. Or make your own, of course, with one of the many commercial jigs available. 👍
thats a bummer because i ordered one off them on the 9th of this month and am still waiting for it. thought it might have been with me by now to be honest. really hope i dont have to start any sort of process to get my money back off them. if only i had know this before i ordered.
just wanted to update this with the outcome. i sent an email asking when my order would be dispatched and waited. 4 days later i got a email back simply saying that a refund had been issued and would be in my bank soon. nothing else. no explanation or anything. all it said was "Your order from Formatic CNC has been refunded." A simple 'Sorry' would have been nice... but i suppose at least i got an easy refund. I then went to ebay and ordered a top from there. 3 days later its sat in my living room waiting to be fitted..................Now im happy !!
A Millard Bench. Very nice.
I have seen many good ones but yours fits in UK houses which makes it appealing
Yep - that was the main reason for the build. 👍👍
@@10MinuteWorkshop Could you drill some 2" holes in the legs and frame to get the weight down?
It shouldn't effect the strength.
Excellent
Thanks! 👍
Peter I'm lovin' that sacrificial strip that's routed in ;-)
Thanks! 🙌👍