![weakbit](/img/default-banner.jpg)
- Видео 143
- Просмотров 280 037
weakbit
Добавлен 20 дек 2019
CD-Player and HiFi Equipment
Yamaha CD-640 and R-840 repair
This is a interest CD-Player! Never have a CD-Player like that - you need both machines to start the CD-Player. The R-840 Amplifier and Controller for the CD-Player CD-640 is important and if you disconnect it from the other part the CD-Player never will start again! Let's have a look on the issue. Please subscribe and Thank you for watching! weakbit
Просмотров: 920
Видео
Siemens FM428 Stereo Video2000 restoration
Просмотров 2214 месяца назад
It is unbelievable that this 40years old Video2000 machine find the way to my kitchen table. But the list of failures are unlimited. 1st the electrolytic caps are defect then I change this, 2nd the rechargeable battery from the controller card was defect, 3rd the connector form the controller card to the motor is defect, 4th I clean the scanner motor and there are 4 fingers inside this collecto...
Philips CD604 v3 repair
Просмотров 7005 месяцев назад
in the last time I've a bad fortune nothing will go so that I can order a spar-part and repair some old CD-Player. Also here is a example of spar parts they not so working like it should. But let's see what happened in all this CD604 Videos. Please subscribe! Thank you for watching! weakbit
Sony MDS-JE510 & MDS-JE500 repair
Просмотров 3,1 тыс.5 месяцев назад
since the last Sunday is falling out and I can't make a Video this combination will be interest. I start with a silver one Minidisc Recorder and this will end up in a other machine! Well sometime I do that to make from 2 machines one working again. Let's have a look if this will work!? Please subscribe and Thank you for watching! weakbit
Sony CDP-791 repair
Просмотров 1,5 тыс.6 месяцев назад
Sometimes a failure occur but in this case there are more then only one issue? All this issues start simple but become from step to step a more and more complex problem. Let's have a look on this obscure machine. Please subscribe and thank you for watching! weakbit
Philips MCM770 repair
Просмотров 6176 месяцев назад
Some obscure information and a I think easy to find failure make this machine very sympathetic! Look at the nice format of the small device and this is a ideal machine for a small apartment or for youth people they want to start with there new Hifi interests. Please subscribe and Thank you for watching! weakbit
Cambridge Audio azur340c v4
Просмотров 1 тыс.6 месяцев назад
A week of nightmares are over and all that I can repair was only end in a never ending failure! My bed fortune doesn't end with all this failures and this is the maximum. What can I change more on this machine? Have a look what happened with all this missing functions!? Please subscribe and Thank you for watching! weakbit (really bad week!) this is my own CD-Player and I never bring it to run a...
NAD 523 repair v2
Просмотров 4237 месяцев назад
Sometimes it happened that I get a CD-Player back like this NAD 523 and then it have a other issue then it was before. I think this is maybe a long therm effect that some failure come again back to my kitchen table. Please subscribe and Thank you for watching! weakbit
TEAC AG-H300 mk2
Просмотров 6357 месяцев назад
This was and I must say 'sorry' to all my viewers this was not a repair and it was not possible in many cases. A questions to my viewers is should we construct a new one amplifier with a new concept that is time actual? or should we wait for more defect machines where I don't spar parts? Please write all your ideas in the commend line. Please subscribe and Thank you for watching. weakbit
Philips CD604 v1 repair
Просмотров 8757 месяцев назад
The first Video in the year and I must make it in more parts then it will not work for the first time so the first bad impression - haha. What should I say to this issue. Have fun to watch it and remember I never repair this type of CD-Player! Please subscribe and Thank you for watching! weakbit
Sony SLV-SE200 repair
Просмотров 4727 месяцев назад
Very long time ago I repair a lot of video-recorder machines and so it comes that one man asking me about his machine - well the failure is a mystery but could I remember what the failures are? I don't remember after 25year near nothing but let's have a look. Please subscribe and Thank you for watching! weakbit
NAD 5240 repair
Просмотров 8517 месяцев назад
Sometimes I'm wondering what happened with this CD-Player. The missing tone from this CD-Player will producing some questions - but let's see what happened at this machine. Download also the NAD 5240 service-manual to see what happened in the plan elektrotanya.com/nad_5220_5240_sm.pdf/download.html#dl Please subscribe and have a watch on this Video. Thank you for watching! weakbit
Merry Christmas Happy New Year2024
Просмотров 1968 месяцев назад
the all year speech from my side and I say Merry X-mas & Happy New Year 2024Thank you for Watching! weakbit
Mission DAD5 repair
Просмотров 5868 месяцев назад
sometimes a CD-Player is coming to my kitchen table and at the first sight there is nothing happened? But there was a issue to declare but not only one. Let's have a look to the inside of this fascinating machine and how it is build. Please subscribe and thank you for watching! weakbit
Yamaha RX-E810 v7 repair
Просмотров 9418 месяцев назад
A well known machine this Yamaha RX-E810 at this repair. I'm searching some issue and hope so that I can answer also during the repair a unknown change occur but see self what happened to this very special Video! If you want to follow the service manual more then you can download it here: elektrotanya.com/yamaha_rx-e410_810.pdf/download.html there you can also see the schematic from this machin...
Philips CD824 spectrum analyzing and recap
Просмотров 1,4 тыс.11 месяцев назад
Philips CD824 spectrum analyzing and recap
Didn't show how to adjust the laser power; just said that he did it !!
lowest as possible due the EFM package looks good like the eye pattern must be in a good shape. (with a original pressed CD)
Interesting Video. Do you have a shop in Austria? Is it possible to get things repaired there?
We've had a repair-service in 1996 - 1997 then later I run a company but today I'm disability retired. It is not legal to run a business if you're in disability Pension. There is no shop or any service available here and I do not repair anymore. This Video was made first for fun then for the YPP (RUclips Partner Program) till the payout time come and then my Passport was not accept from the IRS (Finance Administration) for the ITIN (Individual Taxpayer Identification Number) - so RUclips need this ITIN number to pay out but the IRS don't accept my Passport. Now I stop to make my Videos. I think RUclips have there company in Irland and this is in Europe but they don't want to pay out in case of there US law situation. Why is no repair shop in your country?
RT (Russia Today) has ceased to air transmitting quite a while ago due to the conflicts between Russia and Ukraine.
BVN is known as Beste van de Vlaams en Nederlands. Basically a Dutch/Flemish TV channel showing TV shows, soaps and news that were hosted on Belgian Flemish TV and Netherlands TV. It's Free to air, usually showing old TV shows back in the time.
Interesting, i have one like it the only problem the dvd do not turn. Ay idea? thanks
I think if the Laser don't light up the initial don't work and this means no DVD/CD inside so the spin don't turn to on.
saya dari indonesia punya radio icom 731 s kondisi sangat bagus saya suka radio nya
Saat ini teknologi ini sudah ketinggalan zaman; ada sistem yang sangat berbeda seperti SDR (Software Defined Radion). Saya akan merekomendasikan Anda ICOM IC-7300 atau bidang Yaesu FT-710 (DSP) atau FT101 (ini adalah mixer). 73
Hello. I bought a second-hand SON MDS JA555ES, but unfortunately it says error C13 and ejects the disk. After examining it, I found that the disc does not spin or the optics do not light up, even with the service menu, endless playback. The magnetic head is focused and the optics are moved. I checked the limit switches. You would help me a lot if I could make it passable.
please download the service manual elektrotanya.com/sony_mds-ja555es.pdf/download.html - I've only repair ones this machine and there was so in my Video to see a mechanical issue that I fix.
@@weakbit633 thank you I already have this one downloaded too. I don't know if I should look for it as a problem with the optics or with the disc rotation. The disk should spin even if the optics do not work? It would help me, maybe, if I had an answer to that. Because there are some transistors in front of the optics that control it.
i remember a Sky Anoloug in UK and i managed to take the old box home after asking mom about it and me being super young i wanted to know how it worked. i managed to get a fuzzy Pic when i put my finger on the cable until i removed my finger not sure how my body got a sattilight sig but after a few times i gave up. many years later i also wonder if them boxes could be used to pickup Middle eastern tv of some kind as our house had a Massive Dish that i was told could receive sattelight from near india or something
but this Humax IRCI-5400 is a DVB-S digital Box with MPEG2 and can't receive any analogue signal! Sky was on Astra 19,2°E and send in a encoded signal in Videocrypt2 - the lines where shifted in steps from about 256 position via the cut & rotate method. The best hack on this is from 'Captain Jack' and it is show in this Video ruclips.net/video/fLgV94x5Wb4/видео.html
I think you put the springs in wrong. I don't think they are supposed to go around the rubber grommets, otherwise the grommets don't do anything. They are there to interface with the springs and absorb vibration.
It's impressive how Giga Blue Trio reads Oscam better and faster than Dreambox. I know few germans channels like Sat 1, RTL, RTL2, Prosieben and Sixx. I do best know SAT.1 on 19.2E.... have seen many germans channel on a ferry, on a ride from Iceland to Denmark. may be because many germans channels are uncrypted/unscrampled
But Sat1, RTL, RTL2, ProSieben are not encoded - the SD576 are not encoded only the HD+ they are 720 or 1080 they are encoded. You need a Smart-Card HD+ for it so you have the private German stations within HD1080. The Smart-Card HD+ cost for the German package around €7/month.
@@weakbit633 i was way to fast i meant HD version of them. I bought a HD+ card and receiving them perfectly with 75 cm dish here in the middle of the north atlantic in Faroe Islands. Signal quality is 93% and some few are actutally around 81-86%. I have maximum signal at 28.2E Signal Strength 96% signal quality 100% on every each channel. What i got THOR 0.8W Thor 5/6 (Nordic Beam) Signal quality in dB is around 14.9 dB and some few around 15.2 - 15.4 with an 90 cm dish. Hotbird 13.0E Hotbird do actually have same signal quality here with an 85 cm dish. 19.2E is enough with an 75 cm dish. To receive all channels that are available at 19.2 east.... The most intressting satellite in my area is located at 28.2E. With an dish sizes 70 cm. signal quality in dB is around 15.1 - 15.3 for FTA channels. Sky UK beam is around 14.5 - 14.8 dB with an 85 cm i got 16.7 - 17.3 dB on Sky Beam and 17.2 - 17.7 dB on FTA channels.... I have tried diffrent sizes dish from 65 cm and up to 120 cm. The first satellite that is way to weak is Thor 0.8W 2nd HotBird 13.0E then Astra 19.2E and Astra 28.2E is around 12.9 - 13.3 dB Most famous satellite here is Thor 0.8W (Nordic beam channels) and then Astra 28.2E and then Astra 19.2E. We do not use motor. We use multiple satellite dishes because of the elevation. They are far away from eachother wihich make it impossible to get all channels correctly. I receive 4 satellite which means i have 4 satellite dishes. With an diseqc. LNB1 Thor 0.8W. LNB2 Astra 28.2E. LNB3 Astra 19.2E. LNB4 Hotbird 13.0E. Information from dishpointer.com THOR 0.8W - Elevation 19.5 Astra 19.2E - Elevation 16.4 Hotbird 13.0 - Elevation 17.7 Astra 28.2E - Elevation 13.9
@@weakbit633 i have everything on Gigablue 4k Trio. I receive these satellites perfectly • THOR 0.8W (Nordic beam) Thor 5 & Thor 6. • HOTBIRD 13.0E (all channels) • ASTRA 19.2E (all channels) • ASTRA 23.5E (all channels) • ASTRA 28.2E (both Freesat and Sky) • ATLANTIC BIRD 12.5W (60% of the channels) • EUTELSAT 16.0E (all channels) • EUTELSAT 3.1E (all channels) • HELLASAT3 39.0E (40% of the channels) • EUTELSAT 39.0E (almost all channels) • EUTELSAT 9B - 9.0E (all channels) • SES-5 5.0E (all channels.
NICE JOB , AND THANK FOR HELP, I HAVE A HARMON CD AND IM GONIG TO REPAIR
Can you tell me, how is the resistance in new transformer ? 🙂
sorry I don't know - I can't remember about this machine.
Guten Tag, Kann ich eine Frage zu diesem Player-Modell an Ihre E-Mail-Adresse senden?
God forbid such specialists!((
I have other problem on same device - when the unit is cold in the morning, remote doesn’t work. After approx. 15-30 minutes remote starts running well! Also phisycal buttons “display” and “memory” are not working. But when I put headphones on jack - buttons start to work for 10 seconds :)) What could be the reason? Thanks a lot!
Hello I can't remember it anymore what happened with special this but I give you a tip download the service manual and have a watch at the power-supply. Also Check the Voltage that could be also wrong and the connections between all this PCB-boards. please read here: elektrotanya.com/yamaha_crx-e100_rx-e100_nx-e100.pdf/download.html
Que CORAJE y DESEPCION da, compra uno el láser y resulta que es un problema de SERVOS en MAL estado 😠😠 🤔🤔
Was that a new laser mechanism? If so did you de-solder the antistatic solder bridge before fitting it? There is a soldered link on the optical units PCB that has to be de-soldered before fitting or the laser will not work. It is bridged to stop static electricity blowing the laser during transit.
Use some extra flux on the SMD chips bitte. Also use de-solder wick to clean the old solder off first. You'll get less solder bridges.
Why not glue an extra aluminium heatsink on top of the original heatsink with thermal tape or thermal glue if this is a common problem? You seem to have a lot of Azures with with blown TA2092N chips. Love you videos, they make me laugh, love your accent. Greetings from the UK, where Cambridge Audio gear is actually made.
Hallo, You do not have to take the entire drive out of the case at all. If you pull the tray forwards there are 2 plastic clips with circles under the tray, GENTLY pull them out to the side a little bit, these lock the tray when fully out. You can then gently pull the tray forwards a little (but not fully out). You can then get more access to the belt to change it, very simple. I had the exact same problems with my Azure 340C even the small switch actuator came off as yours did (the part you glued) or "gutentighted" lol I left that part out and the CD player still worked fine for a while, now it stutters and won't read many discs so I shall glutentight mine in too. GREAT VIDEO BY THE WAY, YOUR ACCENT IS GREAT
Hey FALTO el DIPLAY abuelito esta muy OSCURO......!🤔🤔
Hello ! I need to replace the laser head with Harman Cardon HD-950. I can't take my head off ! The pull-out tray is in the way.
Buena reparación, estos reproductores son muy buenos vale la pena repararlos tienen el audio clarito sin distorsion y potente, sí escuchamos una memoria USB se escucha HORRIBLE son una PORQUERIA las memorias.
I have the same machine that refused to start after a power outage. I was about to leave it for recycling when I saw this video. I just hit the reset button and it works again. Thank you!
Good work my friend 👍
Hi The no sound problem you have is a problem in the power supply pcb.
Hi the problem you have with this machine is normally caused by a problem in the power supply. Hope this helps
Another nice new CDM4 transport wasted It's almost never the laser fyi
Fantastic video
Schwachsinnsvideo!
My original machine deck B exactly same problem, i can't fix it. Lazer ok, but not playing
VU meters for recording levels on deck B
I've got 2 of these machines, identical to yours. Got stuck drawers on deck A. Otherwise play perfectly after 20 years.
Tradu text folosind camera foto greetings from Romania. i have watched your videos hundreds of times....my yamaha 810 won't turn on. I changed the 22uf capacitor but nothing. I don't have a k3850 and I can't find a close equivalent. I made contact between the relay pins on the 230 volt side and the surprise starts after I press the start button. I removed the relay, measured it and the coil is broken. I listened to music like this for hours at a moderate volume and it still works. My question for you is: after measuring the relay power point why do I have 10.4 volts only for 2 seconds when I press the start button then 0 volts? I specify that it still works very well, only that it must be removed from the power socket. I am waiting for an answer. Greetings
you can order it here www.ebay.at/itm/400672863535
The problem with this compact unit is very strange. It sounds to me like the audio and reading capacitors are failing. It is a very typical problem for Technics and Pioneer. I am a technician and I know what I am talking about, especially if you have already changed the optic, the optic is not the audio capacitor. and reading in Technics and Pioneer, the capacitors that usually cause problems are the 1uf 50v 22uf 6.3v and 47uf 6.3v in 99 percent of the Technics and Pioneer that they brought me from other technicians who directly blame the optician with the recap of those 3 Capacitors came back to life and to this day they work without any problems. I would recap that compacter and you know how it comes back to life. That's probably the problem.
Hi I just got an old Sony cdp 797 cd player but my problem is the volume is very low through the 2 sony speakers .I don't have the remote control .Any help would be appreciated .thanks
Hello! Denon DCM-500AE does not turn on after three years of rest. The display does not light up. What are the most likely causes?
how to pair remote
Tip for silver. This symptom is when procesor have problems with communication with BD board under mechanism.
Original battery is rechargeable! And it's charge when unit is in AC.
Espero me pueda ayudar un saludo desde Arequipa Perú gracias
Is the GigaBlue Trio software stable? Is it easy to update the software?
I wish i have the skills nice man
Hello, when I bought this device, it had exactly the same problem. After watching your training clip, I first replaced the belt and the 1000 microfarad 35V capacitor. The problem was solved by about 95%, and it only gave errors sometimes, but after replacing the 6800 microfarad capacitor, I replaced it, the device no longer works and only gives error messages, what is the reason?
My first CD player ❤
Hello Mr Weakbit, so sad that WE have not New vidéos from you... Hope you are well. Give us some news please
Have you (mr weakbit) got a beef with everything british we wouldn't want to start another war now would we now.
Is Philips a British company? in this Mission is all from Philips built in. so what?
One of the reasons laser pickup is skipping tracks at the end of CD is that the ribbon (especially OEM ribbon) comes in close proximity/contact with the transformer. The EM field from the transformer interrupts the work of the laser via the ribbon, so the laser skips/stops. You can verify this by placing some protective plastic between the transformer and the ribbon: it skips less.
great install))
I found this Cambridge CD player in the trash bin. I would like check inside as the CD drawer won't open. Could you please let know the type of screw driver for the screws on the top cover. Thank you.
I think I remember it was a Torx T6.