Thank God, i was watching this and several other videos on bad Hall sensors and i just checked my motor wires again more closely and found that one of them just disconnected, I'd thought I shorted out some wires because they melted but it looks like one just came apart, the big yellow wire going to the hub motor. So, morel of the story is check all connections first which I've known forever. Thanks.
I need your help. I have Carrera ebike I am trying to install throttle but I am facing E21 . I removed the crank sensor which is already dead. What do now ?
Power The battery may not be supplying enough power to the controller. This can happen on Rad Power Bikes, Ride1UP, and Aventon ebikes. Speed sensor The speed sensor may not be working properly, which can prevent the bike's pedal assist from working. This can happen on mid-drive ebikes. Current The motor current output may be too high, causing the controller to shut down to prevent overheating. This can happen on Aventon ebikes, especially when climbing for long periods with maximum pedal assist turned on
This helped a lot as my eBike has a 3 pin connector to the motor & nothing works but the battery & connectors are hot. No continuity on any of the 11 pin main harness connector. The PAS if connected should activate the motor it looks like with or without turning the control screen on the 5 pin connector on.
Saam have u worked with any bottombracket torguesensor controllers yet? Im trying to make a PAS work with torgue sensor but with controller theres no wires for it ,what wires can i bridge to get a PAS connector
I have dome what you said in the video to allow the ebike to work but now it is working at one speed, how do i increase the speeds without the screen and buttons ?
@@SaamE-bike interesting because my screen showed 5 speeds and would have a top speed of 45 mph but now that the screen has broken and I removed it the bike only tops out at 39mph and accelerates much slower than before? Any idea what the issue maybe
@8:09 whats the setup and which wires coming from and going to where for that connection on turning the controller on with that toggle switch. I think thats the main question here. Tha kbyiu
@@SaamE-bike okay, you're using that toggle switch to turn power on to the controller, correct? What my question is how do you hook up a toggle switch to turn the power on to the controller in order to power the assisted pedal buttons and the throttle
Can I use the peddle wires for a twist throttle or swap the the 4pin throttle to a 3pin twist throttle harness colour wires are red orange white black and the twist throttle is red green black what wires go to witch
Hi thanks for the lovely Video, I managed to put back a few bikes together. Thanks to you.but unfortunately I can't get hold of the controller anymore. If you do have a new link please let me know. Thankyou once again 🙏
I never hooked up PAS on my ebike kit and ran it without that for a few years but I just recently shorted out my hall sensor i think, so do i have to hook up the PAS now to make it work if i don't want to repair the hall sensor/sensors. Thanks.
I have a 250 W E- bike regular controller. I wanted to use the s. W 900 for display on that, but it doesn't have the same pin outs as the controller. It came with anyway. My hall sensor wires broke yesterday and I got no time to wait for parts. I'm hoping I can just take those off. And it will work the same. I have pedal assist Wires did.I had to tuck up because the controller?I have for it now.Doesn't have that just high low and mid rain speed.I guess my point is, can I just take these hall sensors off and use the pedal assist as a throttle if I connect that to the throttle or can I use my twist throttle?Still sorry about the wrong question
As far I understand your hall sensor connection is damage right, if so then you can only use 3 pass wires blue green and yellow.. it will work some controller if is dual mode controller..
Hi yes u can... some controller has 2 single cable white or blue. If is there fast switch on your bike upside down then connect those cable for 2 seconds will run 🏃♂️ forwthenas soon is spin u can remove... or you swap 3 motor cable
Hello Sam can you help me ..I have a rich bit 1000w bike i change the controler, the battery is ok ,the display its shown nothing no power when I pressed simultaneous power and for example the lights or the horn i se a little light and a small sound of the horn...They told me all problem can be on display.. i open the display no screws nothing but i open but i don't understand nothing..if put together blue and red how you make she gona start ? You have Facebook page or something to send you a video..Thanks
Hello. I am going to travel tommorow and take the controller-display back to my home city, so that I have it checked to an electronic friend. Should I ride the e-scooter without the display,using your method, until it is fixed? Or is this method harmful for my e-scooter? It wont even turn on with damaged display, should I do this trick, or better wait until display is normally fixed and placed again on me bike? Thanks. (its like a normal motor in size and shape, see the sporty e-scooter as well)
@@SaamE-bike Ah Ha the light just lit on what you mean on dual controller to use the thumb throttle & the cadence sensor I hear it called or PAS or foot throttle is my term. Just got a spark connecting the controller to the 48V battery so that a good sign of controller life right? Even with the battery turned off at 4-7V anyway.
Nice Video but what you say is not always through i think....so my display and a lot of others have no blue and red wire....like these ....APT/No.2/S5/Bafang protocol: It’s 5pins out from controller and display, which display could be adjustable for setting lots parameters, like wheel size, motor poles, voltage etc. This design more suitable for ebike, electric bicycle application. 🤔
@gauravjoshi9183 fast u can try with swapping 💚 blue 💙 and yellow 💛 motor cables.. and check there is any single cable white or blue.. if don't work i gas your controller is single mode not dual..
@@SaamE-bike my controller is dual mode controller.. But the motor locking at low RPM is a major issue when gives a sudden jerk. My motor is geared motor.. I pedal as hard as I can but it locks at times
THIS no work!! I try on go trax R1 folding ebike... display unresponsive we tie red blue together and NO work motor!! Hall sensor no matter NO WORK!! please help explain better, many wires on your desktop and other messy things tricks we are NOT saying BUT help,!!
Quickly we NEED throttle and motor to WORK and we ride ebike show QUICKLY it WORK, we see lot of thongs your video NO PERFECT NO WORK!!! we NEED WORK!!
My priest has a hell sensor, but my ebike has HALL sensors.
Thank God, i was watching this and several other videos on bad Hall sensors and i just checked my motor wires again more closely and found that one of them just disconnected, I'd thought I shorted out some wires because they melted but it looks like one just came apart, the big yellow wire going to the hub motor.
So, morel of the story is check all connections first which I've known forever.
Thanks.
Thankyou so much for the lovely video, I managed to fix my Carrera and add a throttle to it....God bless you
Thanks for your support 🙏 I'm really glad to help..
Hi
I need your help. I have Carrera ebike I am trying to install throttle but I am facing E21 . I removed the crank sensor which is already dead. What do now ?
Power
The battery may not be supplying enough power to the controller. This can happen on Rad Power Bikes, Ride1UP, and Aventon ebikes.
Speed sensor
The speed sensor may not be working properly, which can prevent the bike's pedal assist from working. This can happen on mid-drive ebikes.
Current
The motor current output may be too high, causing the controller to shut down to prevent overheating. This can happen on Aventon ebikes, especially when climbing for long periods with maximum pedal assist turned on
@@SaamE-bike thank you very much. The pedal sensor is completely damaged. So I decided to install a throttle but I'm facing E21 error.
This helped a lot as my eBike has a 3 pin connector to the motor & nothing works but the battery & connectors are hot. No continuity on any of the 11 pin main harness connector. The PAS if connected should activate the motor it looks like with or without turning the control screen on the 5 pin connector on.
Hello can you send links where you buy the controller
Saam have u worked with any bottombracket torguesensor controllers yet? Im trying to make a PAS work with torgue sensor but with controller theres no wires for it ,what wires can i bridge to get a PAS connector
Hello I've got a question, how do I increase the speed modes without the plus and minus buttons ?
I have dome what you said in the video to allow the ebike to work but now it is working at one speed, how do i increase the speeds without the screen and buttons ?
Hi my friend it should be working full speed unless your controller is single mode
@@SaamE-bike interesting because my screen showed 5 speeds and would have a top speed of 45 mph but now that the screen has broken and I removed it the bike only tops out at 39mph and accelerates much slower than before? Any idea what the issue maybe
I'm going to try this right now I've been trying to figure out how to get my motor running for weeks now
Good video
Thanks
@8:09 whats the setup and which wires coming from and going to where for that connection on turning the controller on with that toggle switch. I think thats the main question here. Tha kbyiu
I do not understand your question
@@SaamE-bike okay, you're using that toggle switch to turn power on to the controller, correct? What my question is how do you hook up a toggle switch to turn the power on to the controller in order to power the assisted pedal buttons and the throttle
This you need dual mode controller otherwise only work on pedal assist only
Hey can you send me a link I got a 2024 ask Go electric bike I'm trying to connect my smart controller and I can't figure it out
What link do u want
Can I use the peddle wires for a twist throttle or swap the the 4pin throttle to a 3pin twist throttle harness colour wires are red orange white black and the twist throttle is red green black what wires go to witch
Normally pedal assist system do not work as a throttle.. you can try
Good .Thanks
Hi thanks for the lovely Video, I managed to put back a few bikes together. Thanks to you.but unfortunately I can't get hold of the controller anymore. If you do have a new link please let me know. Thankyou once again 🙏
U can buy any black controller as ebay
I'm glad to help you ☺️
Ebay link doesn't work
@music4Rsoul hi thanks for your message please check on Ebay black controller for electric bike
Can I install PAS parallel to the throttle switch for my motor controller do not have a PAS port or terminal
All controller has PAS connection.. is not possible to pas connection to work throttle
@@SaamE-bike my China motor controller have no PAS, thanks anyway
That work on tge controler sabvoton 72v150A (M)?
It should work
You are awesome love your video I just subscribed for you channel
Thank you very much for your support
Can you show how you hooked it up? I believe you that it can be done.
I am trying to hook up peddle ass. To throttle to display 3 different things
Mate paddle assist won't work as a throttle is 2 different things
Yo i have the brushless motor controler 48v and 250w, motor 48v 250w so max speed on e bike is 36kmh what to do on the controller to go faster
You have to charge battery and controller more like 52v or 60v
@@SaamE-bike how do i do that
How do I connect a sw900 display if I don't have a receiving plug on my controller can I wire all colours to corresponding colours
Hi yes u can do that if is compatible with
@SaamE-bike so can I wire from the sw900 display plug RBBGY TO THE HALL PLUG ?
how about figuring out how to wire a display to a controller not intended for a display so you can get battery and speed information.
U need separate parts for so u can check battery and speed
I never hooked up PAS on my ebike kit and ran it without that for a few years but I just recently shorted out my hall sensor i think, so do i have to hook up the PAS now to make it work if i don't want to repair the hall sensor/sensors.
Thanks.
PS, my 1000 watt controller does say dual mode.
U can try
Some time is dose not says on the controller
I have a 250 W
E- bike regular controller. I wanted to use the s. W 900 for display on that, but it doesn't have the same pin outs as the controller. It came with anyway. My hall sensor wires broke yesterday and I got no time to wait for parts. I'm hoping I can just take those off. And it will work the same. I have pedal assist Wires did.I had to tuck up because the controller?I have for it now.Doesn't have that just high low and mid rain speed.I guess my point is, can I just take these hall sensors off and use the pedal assist as a throttle if I connect that to the throttle or can I use my twist throttle?Still sorry about the wrong question
As far I understand your hall sensor connection is damage right, if so then you can only use 3 pass wires blue green and yellow.. it will work some controller if is dual mode controller..
Will dis controller work the same on a geared hub
@whitefeatherslinger8194 hi yes will do work with gear and gearless thanks
@SaamE-bike saam have u worked on torgue sensor bikes yet? Alot have them in the bottom bracket
Hi my display is not working. It has 4 wires labeled d+ d- ds and pwm. Which wires I need to short?
It should be red and blue
hi can tell my howe to unlock max speed on ebike and turn of pedall asist
Could you send brand name
yes it is MS Energy m11
have c300s display and it is pedal asist ...shengy hub motor 250w 40nm 36v batery 13amp..
The ebay links don't work
If you find any black controller buy it thanks
@saam e-bike I disconnected my hell sensor from controller now my back wheel spins in reverse is there away to make it spin normal
There's a single unused wire for re-learn mode that you have to connect. There are videos showing how to do it.
Hi yes u can... some controller has 2 single cable white or blue. If is there fast switch on your bike upside down then connect those cable for 2 seconds will run 🏃♂️ forwthenas soon is spin u can remove... or you swap 3 motor cable
Thank u so much managed to get it working 👍
@JimBobby-s4e happy to help
Hello Sam can you help me ..I have a rich bit 1000w bike i change the controler, the battery is ok ,the display its shown nothing no power when I pressed simultaneous power and for example the lights or the horn i se a little light and a small sound of the horn...They told me all problem can be on display.. i open the display no screws nothing but i open but i don't understand nothing..if put together blue and red how you make she gona start ? You have Facebook page or something to send you a video..Thanks
Hi thanks for your message unfortunately I don't have u can send me on my email
John garcia, please send me brand of controller and wiring diagram thanks.
Thanks for your message... u can buy from ebay or amazon u can ask the seller to send diagram
Buy black colour controller
Please reply Sam I need your help.Please reply on the one I just sent today sir thanks.
How much just dor the dual controller
Hi u can check price on eBay or amazon 40 to 60 pound
Hello. I am going to travel tommorow and take the controller-display back to my home city, so that I have it checked to an electronic friend. Should I ride the e-scooter without the display,using your method, until it is fixed? Or is this method harmful for my e-scooter? It wont even turn on with damaged display, should I do this trick, or better wait until display is normally fixed and placed again on me bike? Thanks. (its like a normal motor in size and shape, see the sporty e-scooter as well)
If u want to use this on scooter u Need dual mode controller or is only work for pedal assist only
@@SaamE-bike Ah Ha the light just lit on what you mean on dual controller to use the thumb throttle & the cadence sensor I hear it called or PAS or foot throttle is my term. Just got a spark connecting the controller to the 48V battery so that a good sign of controller life right? Even with the battery turned off at 4-7V anyway.
Dual mode controller is u can use without hall sensor connector
Hi will this work when your forgot display password
It should work
Nice Video but what you say is not always through i think....so my display and a lot of others have no blue and red wire....like these ....APT/No.2/S5/Bafang protocol: It’s 5pins out from controller and display, which display could be adjustable for setting lots parameters, like wheel size, motor poles, voltage etc. This design more suitable for ebike, electric bicycle application. 🤔
Thanks e bike most are same cable colours code and Bafang is different
Can you confirm that the bridge you make with red and blue is just the positive in and output of the display?
Yes it is
I have a problem the hall sensor I think damaged and motor can't move what I have to do can I pass the hall sensor
Hi thanks for your message.. u can remove the hall sensor 6 pin connector... but is only work if your connector is dual mode system
My motor runs very rough without hall sensors
@gauravjoshi9183 fast u can try with swapping 💚 blue 💙 and yellow 💛 motor cables.. and check there is any single cable white or blue.. if don't work i gas your controller is single mode not dual..
@@SaamE-bike my controller is dual mode controller.. But the motor locking at low RPM is a major issue when gives a sudden jerk. My motor is geared motor.. I pedal as hard as I can but it locks at times
@@SaamE-bike I wonder how you manage it without hall sensors.. Climbing even average hill without sensors is a task 😩
how do i use light and horn without dispaly
hi if u really want to use light u need separate switch for this
@@SaamE-bike how do i can do that
Good, but you dont show the switch connection
Thanks.. what switch connection
THIS no work!! I try on go trax R1 folding ebike... display unresponsive we tie red blue together and NO work motor!! Hall sensor no matter NO WORK!! please help explain better, many wires on your desktop and other messy things tricks we are NOT saying BUT help,!!
Explain how petal ebike 48v display unresponsive BUT we need throttle and motor to WORK!! QUICKLY we need work!!
Thanks ...
Hey I have bike that can on display but it cannot
What do u mean
eBay link problem
I will check and let you know
Can you send whatsapp number
1:06
😊
Send me the link
YES SEND ME THE LINK SO I CAN ORDER ONE FOR ME SMLRO XDC 600 2000WATTS DUAL MOTORS
U can buy from ebay
I don't know what the problem is
Quickly we NEED throttle and motor to WORK and we ride ebike show QUICKLY it WORK, we see lot of thongs your video NO PERFECT NO WORK!!! we NEED WORK!!
hall sensor But you did not explain how you performed the operation. I did not understand anything
Hi if hell sensor doesn't work on this controller you can use without hell sensor connection because is dual mode controller
Xiaomi
Didn't work in hero' s e cycle controller.
Send me the link
what link