Hello sir. Meron kaba video or na try mo naba mag connect ng Rear motor with 6 wires ung sa hall sensor my white na extra. Tapos i connect sa controller na 5 wires. Anung wire kaya ang pwede hindi pwede i connect ung white? Kasi un lang walang kaparehas na color sa controller. Salamat sa sagot idol. Thank you.
Dual hub po ebike q, rear is 500 watts front is 350 watts. Question, pwede po b gwin ung rear motor q is with hall sensor, front motor is no hall sensor? Then pwede po kya sila sabay n patakbuhin gamit isa lng n throttle?
Wasp bro great video! Question, currently running 60v 45ah. I’d like to add extra power and range. What upgrade do I need to make as far as changing to a new motor hub and controller also how how much battery do I need to add? Thank you broski!
did you try to give a manual spin to engage the non sensor hub with the sensor controller? some scooter wont run unless you turn the wheel over 3-5 km/h thanks
Sir, ask ko lang po, bakit madalas masunog phase wire ko kahit super tight na, and I used heavy duty connector ano po Kaya reason and anong materials maganda gamitin?
Ilang amps ang controller? Ano size ng wire? Bawat size ng wire may corresponding current na kaya lamang nya ihandle. More than that, masusunog ang wire ninyo.
bossing 48v md7 E-006 okay naman controller niya 48v red wire ung iba wire sa hall censor puro 5v na means okay un controller pero E006 siya d umaandar un hub
yung sa throttle may iba pang kasama na function aside sa throttle? pero normally throttle is ren/green or gray/black, yung pang apat na don baka sa switch or cruise control or any auxialliary
Hello! 🙂 Have you connected the Throttle Throttle Display to the Controller connector for Throat Sensors?! Don't have your day gad display connected to a controller display port?! I have the LH-100 Gas Display E-11 Communications transmit error! And when I press the gas the engine doesn't run! What can I PLEASE do? Please help me you are a pro! You understand everything!! 👍👍👍 I bought my 4 50W/750W controllers in a set with S866 Lcd bike display and a sensor that was all in one purchase in one set! It works Dax S866 display with external throttle which is on handlebar with red black green wire on controller red black and white wire. But the LH-100 24/36V/48V/60V Throttle Throttle Display round 6 pin connector with wire top down to controller on 5 pin connector And when I plug together E-11 is on the bottom of the display and it doesn't throttle! It is red blue black green yellow wire on the display connector from the controller and from the LH-100. Can you PLEASE help me make it work. Something is blocking the gas on the LH-100. Because the S866 Lcd bicycle display works with the original throttle, with the thumb throttle on the handlebars. Do I have to connect the sensor that was included in this set, a black round plastic with 6 metal points on it and a round silver metal magnet with a 3-pin connector?! I don't think so because that's only for one bike, isn't it? Please help me! That would be so nice of you! Kind regards. 🙂
Hello sir. Meron kaba video or na try mo naba mag connect ng Rear motor with 6 wires ung sa hall sensor my white na extra. Tapos i connect sa controller na 5 wires. Anung wire kaya ang pwede hindi pwede i connect ung white? Kasi un lang walang kaparehas na color sa controller. Salamat sa sagot idol. Thank you.
Sir how can I work the controller without the display will use another throttle without display
Dual hub po ebike q, rear is 500 watts front is 350 watts. Question, pwede po b gwin ung rear motor q is with hall sensor, front motor is no hall sensor? Then pwede po kya sila sabay n patakbuhin gamit isa lng n throttle?
salamat sa video sir, answer my question for using j&p controller and throttle sa hub ko na may hall censor, keep it up and more power
ano pong question nila? thank you po
How do I say that a motor that does not have a sensor in the controller supports the consultant?
Wasp bro great video! Question, currently running 60v 45ah. I’d like to add extra power and range. What upgrade do I need to make as far as changing to a new motor hub and controller also how how much battery do I need to add? Thank you broski!
More battery. Or higher specs of controller.
Nice sharing
Thanks for visiting
did you try to give a manual spin to engage the non sensor hub with the sensor controller?
some scooter wont run unless you turn the wheel over 3-5 km/h
thanks
hi, good suggestion, let me try brother tomorrow and update you in comment
i think not work even u try to spin the motor manualy because the sensored controler need signal triger comming from the hub motor to work it
sir ilang amps po j&p 36v controller po ang gamit nyo sa video, may available po ba kayo na ganyang 36v j&p controller? tia
16A lang po, meron po kami 48V 25A
Sir, ask ko lang po, bakit madalas masunog phase wire ko kahit super tight na, and I used heavy duty connector ano po Kaya reason and anong materials maganda gamitin?
Ilang amps ang controller? Ano size ng wire? Bawat size ng wire may corresponding current na kaya lamang nya ihandle. More than that, masusunog ang wire ninyo.
bossing 48v md7 E-006 okay naman controller niya 48v red wire ung iba wire sa hall censor puro 5v na means okay un controller pero E006 siya d umaandar un hub
Communication line between throttle and controller check sir, baka may loose or cut.
Lods ask ko lng pano malaman throttle 4pins galing sa e trike panu un e convert sa 3pin bka mg kamali ako masira nnmn, tanx godbless more power
yung sa throttle may iba pang kasama na function aside sa throttle? pero normally throttle is ren/green or gray/black, yung pang apat na don baka sa switch or cruise control or any auxialliary
Boss paano po ba ang taman pag linis ng hub ?
open > brush > punas > varnish (optional) > sealant > close
Hi can use miminmotor with sealup thorttle?
😅
no, you need to use the original Minimotors throttle or the J&P throttle
😅 thanks you ,will buy at your shop
Hello! 🙂
Have you connected the Throttle Throttle Display to the Controller connector for Throat Sensors?! Don't have your day gad display connected to a controller display port?! I have the LH-100 Gas Display E-11 Communications transmit error! And when I press the gas the engine doesn't run! What can I PLEASE do? Please help me you are a pro! You understand everything!! 👍👍👍 I bought my 4 50W/750W controllers in a set with S866 Lcd bike display and a sensor that was all in one purchase in one set! It works Dax S866 display with external throttle which is on handlebar with red black green wire on controller red black and white wire. But the LH-100 24/36V/48V/60V Throttle Throttle Display round 6 pin connector with wire top down to controller on 5 pin connector And when I plug together E-11 is on the bottom of the display and it doesn't throttle! It is red blue black green yellow wire on the display connector from the controller and from the LH-100. Can you PLEASE help me make it work. Something is blocking the gas on the LH-100. Because the S866 Lcd bicycle display works with the original throttle, with the thumb throttle on the handlebars. Do I have to connect the sensor that was included in this set, a black round plastic with 6 metal points on it and a round silver metal magnet with a 3-pin connector?! I don't think so because that's only for one bike, isn't it? Please help me! That would be so nice of you! Kind regards. 🙂
please message me in page
pleas tel about display wair comleat detea
l
can you rephrase your question?
Minidualtron ung escooter ko okay nman pro ayaw gumakaw ung motor paano ang gagawin ko sir?
check wiring, check controller, need technician
Hi they ask me minimotor what vote 36v or 48v ? ?
Order 48V 1set with controller and Torrttle, this is ok😅
Hi bro,mini motor is what vote ,??? 36v or 48v ??
Normally 48v and up
Both controllers are 500w??
nope
Hola?
hello