thank you so much! dear lord you are a blessing. my controller has frayed wires and wont start intermittantly, today it died and i need my bike to get to work. i was looking at missing some work while waiting 4 to 5 days to order a replacement screen. this worked no issues. again cannot thank you enough for this video, your an absolute saviour! you have a lifetime subscriber!
I've got it quite a few blue wires and red so I'm having a hard time following which I have the sw900 display. And it's giving me a false battery reading and I've checked the battery it's fine
I really have no idea but it seems to me that would be the case because if the speed is limited by the Display then I suppose it will override without Display. Sometimes, controllers have a way to limit the speed as well so it could be possible the controller is limited by speed but probably NOT. Hall sensors from the motor help controllers provided speeds data I believe
@@batmanofinglewood when I power on my controller the default setting doesn’t give me throttle control is there a way to change it without display working
I'm not sure. I have sabvoton bluetooth controller with a crappy display. I got rid of the display and connected the Red & Blue from the display wire to activate the controller. I don't know what kind of system your running. I now use my phone as my display because the controller is bluetooth and I built my own 72v Battery Pack with Bluetooth BMS so I can monitor my battery from my phone as well
@batmanofinglewood thanks on my display the sw900 it has a button to cycle through 5 power modes this button is attached to the display so if I remove the display which will remove the button also will it be stuck in 5th speed which is full speed or will it be stuck in the 1st speed ?
Is your battery full if you're showing 40 volts that is basically almost fully charged 36 volt system or it is a depleted 48 volt system or a depleted 48 volt battery in need of charging however in general you should get your main battery voltage between red and negative or black from red to blue you should get just a little bit under that first reading which you got the yellow and green wires are usually communication signal wires you don't want to mess with those
Heya. Will this also work for the KT controllers? I think they should as they have the same julet cable connections that you have. My controller has the same 5wires comming out of the 1-4 cable that connects to the lcd display & throttle. I’m asking because my on/off switch on my lcd display has been acting up so bad. But i still want to be able to ride the bike while i wait for my new lcd to arrive. Thanks.
I'm sorry you're having issues. I only can say this works with Sabvoton Controllers. But many ppl have said it has worked for them. It NEVER stated if they were using a Sabvoton Controller. You may have to try it out (at your own risk) of course. That's my disclaimer. 🫱🫲🤝 If so, try only applying very little turn to the throttle as possible and slowly build up for testing and MAYBE it will work out. Please let me know whether or not it worked so I can know as well. THANKS IN ADVANCED 😎👍🏿
@@batmanofinglewood thanks. Tbh i dont even mind using pedal assist only. As long as i get power i’m fine. I’ll give it a go and see to be honest. Thanks for your super fast reply. Appreciate it.
Batman, Since youve got the cable cut already, would you be willing to make another video where youve found out which female pins are the red and blue so that then it would be real easy to short those in the female end with a little u shaped piece of wire? Thanks for the video btw.
Your talking about a bridge. Yes, if I get the chance this week or maybe today. After I analyze the wire, if it makes sense, I'll do a vid. But this could potentially cause a serious problem. Controller could be TOTALLY DAMAGED if done improperly. I just subscribe to you😎
Not all SW 900 displays are wired up the same way as far as the location of each color wire in relation to the pins which are in the connector every e-bike manufacturer that might happen to use a similar display has a different wiring diagram I'm assuming for patent or copyright purposes something to that effect if you were to take 10 versions of the same display from different e-bike manufacturers the wiring order would not be the same for at least half of them there is a possibility that some are similar but it's not always true so be careful following people's instructions on these videos like this it's best to use a scrap connector stripped wire leads and use a Multimeter to check for the power coming out of each wire and if you're capable of doing that there is a way to locate and determine each wires function well you have power running into the controller
Hey i recently got one of those displays but i dont have a 5 pin connecter my bike take a 4 pin i connected everything how it was connected from stock but the display would not turn on my bike would just go forward any fixes please?
Never heard nor seen an EV system with 4pins they always have 5 pins from my 11 yrs knowledge. Sry I couldn't help at the moment. I believe i will find the answer. I WILL get back to you a.s.a.p
Ok first I have to say if something goes wrong, I'm ABSOLUTELY NOT RESPONSIBLE for your devices. If the bike is working I'm pretty sure you have the RED and BLUE wire in the correct position. DONT TOUCH THE RED OR BLUE WIRES. only the other two wires should be changed up. If you have the Black and White wires in place but NOT the Green, and the green is unplugged, switch the loose Green wire with the Plugged white wire. Leave the white wire unplugged and see what happens. Let me know a.s.a.p.
@@batmanofinglewood this should work the white wire is disconnected on the end of the connecter where it connects to the bike controller unit i will let you know if this works tomorrow it is very late where i live and i cannot do it at the moment thank you for helping i am glad i came to youtube knowing myself i would have switched the wires you told me not to thank you once agian i will get back to you tomorrow
@@batmanofinglewood hey i did as you said the bike still goes forward but the display dose turn on let me tell you how it is connected red to red blue to blue black to black green to green white to white
I just got the info for you brother. The Red is whatever your Battery Voltage is + positive. The black is whatever battery voltage is - negative. In my case, 72v battery so my bike will be Red+ 72v, Black- 72v and so on. Cheers Mate🍻
So if you connect the red and blue wires together will pedal assist work or just throttle? I just don’t want the bike taking off. Also will it harm the controller doing this? I have an Lectric bike with a E-5 display will any e-5 display work on this bike or does it have to be Lectric brand? Thanks for your help.
I'm not sure if this will work for your controller. The safe way to do so is to lift the rear wheel off of the ground before testing. I'm using Sabvoton bluetooth controller for my setup. If may differ from your controller but may not? USE AT YOUR OWN DISCRETION. IM NOT RESPONSIBLE FOR WHAT MAY HAPPEN TO TOUR DEVICES 👍🏾😎
@@batmanofinglewood Sir if you do not mind : Could I connect BMS with 15 wires to 48volt battery wich is 13s = 14 tip/point ?? Could I or it is only for 52v battery = 14s = 15 point ???
@@mhmdsaleh3502 I'm kinda confused of your question. I'll say this; if you have a 20s BMS, you can wire it up to do less but NOT more. Example: 20s BMS = 72v Nominal If I want, I can wire it to a lower voltage. Not a higher. Need a BMS that matches the number of series connections the battery has.
@@batmanofinglewood Yes sir. My confused that : BMS has 15 wire .. the battery has 14 point. If I could connect it , where should I put the last or the first wire of BMS which is without place now ! Thanks and sorry for annoying
Question what if I wanted to change a cord myself I have a 6 pin male I want to change it to 5 pin male for the 6 pin, the colours are Green, Blue, Yellow, Red, White, black and on the 5 pin it’s Green, Blue, Yellow, Red and Black, there is no white on the 5 pin, what would I do with the white?
You should be using a multi meter to check for continuity of each wire. Wire set-up from the plug 🔌 might not be standard. The info I give in this video is for people using Sabvoton Controllers. It may work for others
Hey I'm sending a message for help put about my ebike build. I put a 1 minute video up showing how I'm not getting the right amount of volts out of my bms and when I plug into my controller the volts drop down to 0 or 1 volt. Of you could watch the video and possibly help me out with some advice I would GREATLY appreciate it!
Did you activate your BMS? Some BMS's have to be activated once you connect everything. Does it have any information about how to activate your BMS on the BMS itself? Or does it come with manual?
I needed to activate mine by touching a 3v -12v battery to the specified wires for less than half a second to activate. You might have these factors to settle the issue
I will record more for you great people in about 1 month. I'm trying to heal from getting tattooed. 🤣 plus I'm getting much more in the next few days so maybe I'll just do a few more garage videos. After I get them. But I REALLY need to do more riding vids. THANKS FOR SPEAKING UP😎👍🏾
At least you can get the thing to work. Do you want to walk the bike home or ride the bike home. The features of the display are garbage anyways. If you want to go 10mph go 10mph that's what GPS is for. It's not like you lose control of the throttle output. In other words, you have full throttle control. No boggling unless the controller is Bluetooth and has been programmed to do so
Our display is 5 pin but is joining other bythetime its reaches controller and 5 turned into 10 wires... the blue and red we connected BUT that ONLY powered BOTH break levelers to engage rear break light...we we happy for THAT BUT again otherwise zero occurrence and conclusion ZERO power or motor engagement to operate unit...please any othe advice we would appreciate it...go trax R1 display unresponsive...GO TRAX R1 folding eBike... horrible company zero stock of spare parts...unit is less 10 months old... strongly belived liquid as beer over few weeks ridding and spills killed this...new controller but display out of stock... M5 display powered on less 0.1 second and that also unresponsive!!
@deanziyone2213 nope we got new display SAME shit totally unresponsive.. we had issues with manufacturer obtaining new display as out of stock and M5 SAME shit...now we awaiting OEM display from china whom will program one that's still not from manufacturer...this is horror...
@deanziyone2213 WHAT'S truly going on in THIS industry as the explosion of newer ebikes...the hidden codes and spare part's THAT only the manufacturer holds key's too and wouldn't permission anything beyond there brand, ... suggestions anyone buying anything scooter or ebike should buy quickly these parts as controller and display as when time goes on you want find them...this ebike is time stamped less 10 months old and horror as the brand has a waiting list for parts and copyrights to anyone attempting to provide you that contractor provided part at time of manufacturing.
@deanziyone2213 even obtaining new controller and display matching ...the rear wheel motor contains a lock , suggestions ALL new harness controller display throttle etc you MUST replace and basically only the frame and battery your paying for..but THAT cost of rebuilding is a risk of total uncertainty anything would function.
@batmanofinglewood please check our additional post below...we thinking you only read fist listed as to M6, but that's the last actually before your resoinse
thank you so much! dear lord you are a blessing. my controller has frayed wires and wont start intermittantly, today it died and i need my bike to get to work. i was looking at missing some work while waiting 4 to 5 days to order a replacement screen. this worked no issues. again cannot thank you enough for this video, your an absolute saviour! you have a lifetime subscriber!
Yessss sirrrrr!🫡 Very Greatful for you 🫡😎 I subscribed to you as well 😎
@@batmanofinglewood thank you again, so kind! your fix is going strong worked amazingly all day!
@@unclelunars fail-proof for sure 😁
thank man, has been trying to get over his for years. You're the man.
Always here to help
Mate, you got a like just for your cool name! The info was also very helpful, thanks.
Glad it helped!😎👍🏿 I followed your channel
Hope I never have them issues but great advice 😁thanks
At last some good tips for on the road
Thank you
ABSOLUTELY 😎👍🏾👌🏿
I've got it quite a few blue wires and red so I'm having a hard time following which I have the sw900 display. And it's giving me a false battery reading and I've checked the battery it's fine
Not sure why you have multiple of the same color. Never heard of it. Should only be 5 wires. Black, Red, Blue, Green & White / Yellow
Will this work on bafang hub motor with a king meter 3209 display?
I've only tried this on a Sabvoton Controller
@batmanofinglewood ok thankyou. Would you know if it would possibly bypass factory speed limiter if I tried
I really have no idea but it seems to me that would be the case because if the speed is limited by the Display then I suppose it will override without Display. Sometimes, controllers have a way to limit the speed as well so it could be possible the controller is limited by speed but probably NOT.
Hall sensors from the motor help controllers provided speeds data I believe
You're the man cheers pal
Yes sir 😁👍🏿😎
It worked for me thank you for the well explained directions thank you thank you thank you
Yes sir 😎💪🏾
Hi is this the plug on the controller with red blue green yellow and black thanks
Yes, It's to the 5pin display wire👍🏾
@@batmanofinglewood is there any way to change the power settings as mine defaults to setting 0 with no throttle or power support
I don't quite understand what you mean
@@batmanofinglewood when I power on my controller the default setting doesn’t give me throttle control is there a way to change it without display working
I'm not sure. I have sabvoton bluetooth controller with a crappy display. I got rid of the display and connected the Red & Blue from the display wire to activate the controller. I don't know what kind of system your running.
I now use my phone as my display because the controller is bluetooth and I built my own 72v Battery Pack with Bluetooth BMS so I can monitor my battery from my phone as well
Great advice 👍
Gotta keep spreading the news😎👍🏾
@@batmanofinglewood Yes sir!
What power mode is it in ? Can U leave it in 5th or will it be in 1 once you power on and off?
Without Display there's no governor. In other words, FULL POWER unless you get a governing device like a switch that has Low, Mid & High position
@batmanofinglewood thanks on my display the sw900 it has a button to cycle through 5 power modes this button is attached to the display so if I remove the display which will remove the button also will it be stuck in 5th speed which is full speed or will it be stuck in the 1st speed ?
Same question. Same answer 💁🏾♂️🤷🏾♂️
There is 40v on red at display, does blue send 40 v to controller ?
I don't have those types of systems anymore. It's been too long. I don't remember 😔
Is your battery full if you're showing 40 volts that is basically almost fully charged 36 volt system or it is a depleted 48 volt system or a depleted 48 volt battery in need of charging however in general you should get your main battery voltage between red and negative or black from red to blue you should get just a little bit under that first reading which you got the yellow and green wires are usually communication signal wires you don't want to mess with those
Heya. Will this also work for the KT controllers? I think they should as they have the same julet cable connections that you have. My controller has the same 5wires comming out of the 1-4 cable that connects to the lcd display & throttle.
I’m asking because my on/off switch on my lcd display has been acting up so bad. But i still want to be able to ride the bike while i wait for my new lcd to arrive.
Thanks.
I'm sorry you're having issues. I only can say this works with Sabvoton Controllers. But many ppl have said it has worked for them. It NEVER stated if they were using a Sabvoton Controller. You may have to try it out (at your own risk) of course. That's my disclaimer. 🫱🫲🤝
If so, try only applying very little turn to the throttle as possible and slowly build up for testing and MAYBE it will work out. Please let me know whether or not it worked so I can know as well. THANKS IN ADVANCED 😎👍🏿
@@batmanofinglewood thanks. Tbh i dont even mind using pedal assist only. As long as i get power i’m fine. I’ll give it a go and see to be honest. Thanks for your super fast reply. Appreciate it.
The faster, the better 😎👍🏿🏍️💨
Batman, Since youve got the cable cut already, would you be willing to make another video where youve found out which female pins are the red and blue so that then it would be real easy to short those in the female end with a little u shaped piece of wire? Thanks for the video btw.
Your talking about a bridge. Yes, if I get the chance this week or maybe today. After I analyze the wire, if it makes sense, I'll do a vid. But this could potentially cause a serious problem. Controller could be TOTALLY DAMAGED if done improperly.
I just subscribe to you😎
Facts! Way way more simple, and can find a peace of wire, staple, in order to fix or have on your person. 🎉 you hit that nail right in the head Jeff.
By the way. The greatest gift is knowledge. So thanks for the video, because with out it, we would have never known.
Not all SW 900 displays are wired up the same way as far as the location of each color wire in relation to the pins which are in the connector every e-bike manufacturer that might happen to use a similar display has a different wiring diagram I'm assuming for patent or copyright purposes something to that effect if you were to take 10 versions of the same display from different e-bike manufacturers the wiring order would not be the same for at least half of them there is a possibility that some are similar but it's not always true so be careful following people's instructions on these videos like this it's best to use a scrap connector stripped wire leads and use a Multimeter to check for the power coming out of each wire and if you're capable of doing that there is a way to locate and determine each wires function well you have power running into the controller
Hey i recently got one of those displays but i dont have a 5 pin connecter my bike take a 4 pin i connected everything how it was connected from stock but the display would not turn on my bike would just go forward any fixes please?
Never heard nor seen an EV system with 4pins they always have 5 pins from my 11 yrs knowledge. Sry I couldn't help at the moment. I believe i will find the answer. I WILL get back to you a.s.a.p
@@batmanofinglewood ok thank you
Ok first I have to say if something goes wrong, I'm ABSOLUTELY NOT RESPONSIBLE for your devices.
If the bike is working I'm pretty sure you have the RED and BLUE wire in the correct position. DONT TOUCH THE RED OR BLUE WIRES. only the other two wires should be changed up.
If you have the Black and White wires in place but NOT the Green, and the green is unplugged, switch the loose Green wire with the Plugged white wire. Leave the white wire unplugged and see what happens. Let me know a.s.a.p.
@@batmanofinglewood this should work the white wire is disconnected on the end of the connecter where it connects to the bike controller unit i will let you know if this works tomorrow it is very late where i live and i cannot do it at the moment thank you for helping i am glad i came to youtube knowing myself i would have switched the wires you told me not to thank you once agian i will get back to you tomorrow
@@batmanofinglewood hey i did as you said the bike still goes forward but the display dose turn on let me tell you how it is connected red to red blue to blue black to black green to green white to white
Excellent information. Cheers.
Hi, is the Red cable 38v or 5v?
I just got the info for you brother. The Red is whatever your Battery Voltage is + positive. The black is whatever battery voltage is - negative. In my case, 72v battery so my bike will be Red+ 72v, Black- 72v and so on. Cheers Mate🍻
2:00 You CRACK ME UP!!!
Never Putting Republicans & Democrats Together 🙈🙉🙊
🤣🤣
Will this work on a electric scooter? I done on my electric bike and it worked
It MAY or may NOT. If it's a Sabvoton Controller, then yes it will work😎💪🏿👍🏾 anyways, hope all works out. I appreciate your time spent on my vids
I just subscribed to you
@@batmanofinglewood thanks subscribed aswel
@@batmanofinglewood its 48v 25amp jp48a07 controller for a solar p1 scooter
So if you connect the red and blue wires together will pedal assist work or just throttle? I just don’t want the bike taking off. Also will it harm the controller doing this? I have an Lectric bike with a E-5 display will any e-5 display work on this bike or does it have to be Lectric brand? Thanks for your help.
I'm not sure if this will work for your controller. The safe way to do so is to lift the rear wheel off of the ground before testing. I'm using Sabvoton bluetooth controller for my setup. If may differ from your controller but may not?
USE AT YOUR OWN DISCRETION. IM NOT RESPONSIBLE FOR WHAT MAY HAPPEN TO TOUR DEVICES 👍🏾😎
@@batmanofinglewood m
@@claytonmerchant7161 ? What did you need? I don't see your message
Can I order this plug from somewhere?
Amazon. Five Pin Ebike Plug.
Y can't I ever find some1 doin a quick connect whole harness wiring anywhere...
Hey I have a 6pin and it turn on from the disply any help please
Sry my guy. I've only dealt with the 5-pin. Check on the site endless-sphere.com
Thanks a lot bruuu...❤...
Yes sir. Always 😎
Do you know anything about electric bird bike can you recommend a good electric person who know about electric bikes
What do you need to know?
Excuse me. Could you make this idea practically ? Or in other words. For what should I connect red and blue ? Thanks alot sir
It is so your controller will activate if the display doesn't work
@@batmanofinglewood
Got it .. thanks sir
@@batmanofinglewood
Sir if you do not mind :
Could I connect BMS with 15 wires to 48volt battery wich is 13s = 14 tip/point ??
Could I or it is only for 52v battery = 14s = 15 point ???
@@mhmdsaleh3502 I'm kinda confused of your question. I'll say this; if you have a 20s BMS, you can wire it up to do less but NOT more.
Example:
20s BMS = 72v Nominal
If I want, I can wire it to a lower voltage. Not a higher. Need a BMS that matches the number of series connections the battery has.
@@batmanofinglewood
Yes sir. My confused that :
BMS has 15 wire .. the battery has 14 point. If I could connect it , where should I put the last or the first wire of BMS which is without place now !
Thanks and sorry for annoying
Love u man!
Love you too man! Just subscribed to you
Question what if I wanted to change a cord myself I have a 6 pin male I want to change it to 5 pin male for the 6 pin, the colours are Green, Blue, Yellow, Red, White, black and on the 5 pin it’s Green, Blue, Yellow, Red and Black, there is no white on the 5 pin, what would I do with the white?
White is usually for reading temperature from 6 wire halls sensor plug. Anyways, just tuck it away making sure it doesn't touch other wires.😎👍🏿
@@batmanofinglewood if you have discord or something I’ll show you exactly what I am doing to make sure what you are saying is correct?
I am trying to use a 6 pin throttle/display on a 5 pin wire are you sure I just tuck that wire away?
You should be using a multi meter to check for continuity of each wire. Wire set-up from the plug 🔌 might not be standard.
The info I give in this video is for people using Sabvoton Controllers. It may work for others
Hey I'm sending a message for help put about my ebike build. I put a 1 minute video up showing how I'm not getting the right amount of volts out of my bms and when I plug into my controller the volts drop down to 0 or 1 volt. Of you could watch the video and possibly help me out with some advice I would GREATLY appreciate it!
Did you activate your BMS? Some BMS's have to be activated once you connect everything. Does it have any information about how to activate your BMS on the BMS itself? Or does it come with manual?
I needed to activate mine by touching a 3v -12v battery to the specified wires for less than half a second to activate. You might have these factors to settle the issue
@@batmanofinglewood the bms didn't come with any information. Just the bms. Its driving me crazy! lol
@@batmanofinglewood ill start Googling it. Never thought of that. Not sure why comments aren't allowed on my new videos. I sent a message to RUclips.
@@felonebike9859 it's because you have them set on videos for kids. You have to always choose not for kids
We need some more videos bro
I will record more for you great people in about 1 month. I'm trying to heal from getting tattooed. 🤣 plus I'm getting much more in the next few days so maybe I'll just do a few more garage videos. After I get them. But I REALLY need to do more riding vids.
THANKS FOR SPEAKING UP😎👍🏾
Hello ,shorting the red and blue will allow you to use any display screen?
Shorting the wires let's you use NO display... its just for incase you have NO display or you're display stops working.
@@batmanofinglewood I have broken my buttons from my ukc1 display that's why I asked, can I install any 48,52v throttle with key for example?
@@batmanofinglewood the display is Okey just don't have buttons to turn on and off and select the modes
@@Bm330ci yes. Throttle and display are NOT wire together.
@@Bm330ci you have me confused. How is your display okay if the buttons dont work?
thanks
VERY WELCOME 😎👍🏾
my bafang m620 have different colour wires..
What are the colors?
had the same issue but unfortunately doesnt work
Same here lol, waiting on my screen display to come in
I've only done this on the Sabvoton Controller. I don't know about others
Get a Bluetooth controller and you won't need the display. Just use your phone or a phone you don't use that you can leave on the bike
Just loop the end of the plug with a little piece of wire bout 1 1/2” long
👍
Yes sir
I just subscribed to you
ya but know your stuck in limp mode
At least you can get the thing to work. Do you want to walk the bike home or ride the bike home. The features of the display are garbage anyways. If you want to go 10mph go 10mph that's what GPS is for. It's not like you lose control of the throttle output. In other words, you have full throttle control. No boggling unless the controller is Bluetooth and has been programmed to do so
J'ai oublié mon mot de passe.jarrive pas a démarré mon desplay
Désolé. je ne peux pas aider avec ça. je n'ai pas d'affichage avec mot de passe
merci de répondre en anglais
Ja commandé desplay dm03.jai reçu avec fiche mâle et le câble mâle aussi ?!
merci de répondre en anglais
Our display is 5 pin but is joining other bythetime its reaches controller and 5 turned into 10 wires... the blue and red we connected BUT that ONLY powered BOTH break levelers to engage rear break light...we we happy for THAT BUT again otherwise zero occurrence and conclusion ZERO power or motor engagement to operate unit...please any othe advice we would appreciate it...go trax R1 display unresponsive...GO TRAX R1 folding eBike... horrible company zero stock of spare parts...unit is less 10 months old... strongly belived liquid as beer over few weeks ridding and spills killed this...new controller but display out of stock... M5 display powered on less 0.1 second and that also unresponsive!!
If your screen blips it's not the screen but the controller maybe?
@deanziyone2213 nope we got new display SAME shit totally unresponsive.. we had issues with manufacturer obtaining new display as out of stock and M5 SAME shit...now we awaiting OEM display from china whom will program one that's still not from manufacturer...this is horror...
@deanziyone2213 WHAT'S truly going on in THIS industry as the explosion of newer ebikes...the hidden codes and spare part's THAT only the manufacturer holds key's too and wouldn't permission anything beyond there brand, ... suggestions anyone buying anything scooter or ebike should buy quickly these parts as controller and display as when time goes on you want find them...this ebike is time stamped less 10 months old and horror as the brand has a waiting list for parts and copyrights to anyone attempting to provide you that contractor provided part at time of manufacturing.
@deanziyone2213 NO GOD can remedy this as a apple iphone 15 locked 🔐 and sold locked as to unlocked and can function with any carrier sim...
@deanziyone2213 even obtaining new controller and display matching ...the rear wheel motor contains a lock , suggestions ALL new harness controller display throttle etc you MUST replace and basically only the frame and battery your paying for..but THAT cost of rebuilding is a risk of total uncertainty anything would function.
Everyone ADVISE how simply and only wires...this shhh is pour horror more so then my M6 twinn turbo with bosch modules and 85 fuses 20 relays..
How so?
@batmanofinglewood nothing is easy HERE thanks for your reply...we left msg also on your IG
We ONLY need this unit to ride...power motor and run display out stock and m5 display failed
@batmanofinglewood please check our additional post below...we thinking you only read fist listed as to M6, but that's the last actually before your resoinse
Wait, so you're saying you're not using the same display as on the video?
Didn't work
But are you using a Sabvoton Controller?
Can you get a text boad on your video or speak up
NO!!!