Nice smooth flying, and it did well in the wind. Can't believe they have the prop guards in view. I'm really surprised the cages aren't interchangeable as well. I think if I wanted the higher performance, I'd just go to my little 3" with no prop guards. I can zoom the image on it too to remove props in view. I'm pretty sure it is quieter and performs better too. And the pico seems preferable for super close to people and indoors, which is why I bought it in the first place. I also think I'd prefer to give up 5g of weight for a vifly beeper than leds.
Haha..All good points. I wish the props did not show up either, but I did crop in a bit to have them removed. The beeper is a good idea though, over the LEDs. These small motors don’t output a loud beep.
i broke my pavo pico trying to solder LEDS *facepalm* so I bought one of these instead. Really liked the pico (only got 2 flights) hope this one is similar
What do you think about putting bigger motors on the Pavo20? For example 1204 or 1404? BetaFPV has a F405 AIO 20A 2-4S board, so maybe swap that with the original and go 4S with 5000-6000kv motors, any thoughts?
I don’t have the file, but I found it on the BetaFPV website. I’ll link it below(its at the bottom of the page). betafpv.com/products/pavo20-brushless-whoop-quadcopter?srsltid=AfmBOopNtWoC3Cj0X-xohWRNLffQ4aHFJF2D2HHPS6PVE8w4wxodDdtE
Great video, I just ordered mine yesterday. I got the DJI 03 AIR to go with it, but how do you put those smaller individual antennas instead of the long 1. Appreciate the video and any info you can share. Thanks
For someone new to the FPV flying I have a mini 4 pro and the avata so they come ready to fly. Do you happen to have a video showing how to install all the beta flight software to setup the new Pavo20?
The drone comes already configured with BetaFlight. The only thing you'll have to do is go to the "Modes" tab to assign the switches of your radio, and the "OSD" tab to customize your On Screen Display (OSD) layout. I've done a brief video on another drone. I'll leave it linked below: ruclips.net/video/kN0knYQyn38/видео.html
Been 7 months since your review, do you know if bet a flight modified anything to get props out of view or make something that lets you use ND filters?
Hello, good day, thank you very much for your videos, I would like you to help me since I bought the Pavo 20, but I can't link it, I have the DJI remote control 2, I bought the BetaFPV Pavo20 Brushless Whoop Quadcopter - PNP ELRS (For DJI O3 HD Digital VTX), but not binding the RC, can I configure it? or will I have to change it, this will take a long time, thanks for your help
Do you have any videos about lipo charging? I just got this drone set up after never having used dji systems(updating firmware and what not and setting betaflight settings on the drone) and the lipo charging process seems unclear. I have a 3s 450mah 75c, 5Wh, 11.1v battery and want to know what voltage to charge it to 4.20 I assume istead of 4.35v or lower than 4.20 and also what amp to do it at my charger says like 0.5a to 2.0a or around that range but I don't know which to select.
Thank god. I had the filters in my cart now I can change them for vertical ones
Nice smooth flying, and it did well in the wind. Can't believe they have the prop guards in view. I'm really surprised the cages aren't interchangeable as well. I think if I wanted the higher performance, I'd just go to my little 3" with no prop guards. I can zoom the image on it too to remove props in view. I'm pretty sure it is quieter and performs better too. And the pico seems preferable for super close to people and indoors, which is why I bought it in the first place. I also think I'd prefer to give up 5g of weight for a vifly beeper than leds.
Haha..All good points. I wish the props did not show up either, but I did crop in a bit to have them removed. The beeper is a good idea though, over the LEDs. These small motors don’t output a loud beep.
Great video and nice review of the paco 20. Im getting this soon as my main dji 03 whoop. ☺️
Awsome..It is a nice drone and flies great!
Also I think the LEDs might interfere with the filming because of the bright light
I watched Whirly Bloke video on this quad & he went up a notch on the camera mount with the camera & that took props out of view on this quad 🎉
Thanks..I’ll look into that.
i broke my pavo pico trying to solder LEDS *facepalm* so I bought one of these instead. Really liked the pico (only got 2 flights) hope this one is similar
i bought one , i like this little thing . thanks for review
Thank you, I appreciate it.
Thanks for the great details.
You bet!
Nice flying 😊
Thanks, it was fun flying it.
Hi!... Where is the location of the micro SD card for 4K recording?.. thanks
What do you think about putting bigger motors on the Pavo20? For example 1204 or 1404? BetaFPV has a F405 AIO 20A 2-4S board, so maybe swap that with the original and go 4S with 5000-6000kv motors, any thoughts?
New to your channel, awesome job with video..
Great shots bro! Which settings did you use on the O3 to capture the videos?
Thanks….I think this was all done in Auto.
Very nice video,What controller are you using.
It depended on the flight, but Radio Master Pocket and Jumper T-Lite. Both on ELRS at 100mW.
Hey, I got the 03 Pavo 20, you wouldn't happen to have a clue dump you can share? still in the learning phase Og betaflight
I don’t have the file, but I found it on the BetaFPV website. I’ll link it below(its at the bottom of the page).
betafpv.com/products/pavo20-brushless-whoop-quadcopter?srsltid=AfmBOopNtWoC3Cj0X-xohWRNLffQ4aHFJF2D2HHPS6PVE8w4wxodDdtE
Great video, I just ordered mine yesterday. I got the DJI 03 AIR to go with it, but how do you put those smaller individual antennas instead of the long 1. Appreciate the video and any info you can share. Thanks
I show how to do it in this video: ruclips.net/video/t6XlYY5UP34/видео.html
And a full Tutorial here as well: ruclips.net/video/2PXi1TY23GY/видео.html
Congrats on the pyrodrone spot 👏 😊😊
Thanks, I did not know it was on there..I appreciate the heads up.
Ok so as a noob interested in this drone, what goggles and RC do you recommend?
Great content bro. Do you think Pavo20 can be used indoors? Is there a way to lower the power of the engines so that it is slow indoors?
It’s on the verge of being too powerful for indoor flying. You can search how to put a throttle limit on it.
For someone new to the FPV flying I have a mini 4 pro and the avata so they come ready to fly. Do you happen to have a video showing how to install all the beta flight software to setup the new Pavo20?
The drone comes already configured with BetaFlight. The only thing you'll have to do is go to the "Modes" tab to assign the switches of your radio, and the "OSD" tab to customize your On Screen Display (OSD) layout. I've done a brief video on another drone. I'll leave it linked below: ruclips.net/video/kN0knYQyn38/видео.html
Greatly appreciate your help and videos! Thank you..
Subscribed!
Thanks..I appreciate it.
Been 7 months since your review, do you know if bet a flight modified anything to get props out of view or make something that lets you use ND filters?
How much flight time will you get?
Hello, good day, thank you very much for your videos, I would like you to help me since I bought the Pavo 20, but I can't link it, I have the DJI remote control 2, I bought the BetaFPV Pavo20 Brushless Whoop Quadcopter - PNP ELRS (For DJI O3 HD Digital VTX), but not binding the RC, can I configure it? or will I have to change it, this will take a long time, thanks for your help
How does it handle the wind?
Really good, surprisingly
Do you have any videos about lipo charging? I just got this drone set up after never having used dji systems(updating firmware and what not and setting betaflight settings on the drone) and the lipo charging process seems unclear. I have a 3s 450mah 75c, 5Wh, 11.1v battery and want to know what voltage to charge it to 4.20 I assume istead of 4.35v or lower than 4.20 and also what amp to do it at my charger says like 0.5a to 2.0a or around that range but I don't know which to select.
What goggles do you use
DJI Goggles V2
What things I will need for a complete setup?
You’ll need a VTX like the DJI O3 Air Unit, a radio like the Radio Master Pocket or Boxer, and an FPV goggle like the DJI V2, Integra or Goggles2.
Cool👍
Thanks Nick!
Too bad BetaFPV did not notice the props guards in view before releasing this one.
True
Isn’t it possible to 3D print and better canopy?
Great review!👏🏽👏🏽 New sub #StayPhly
Thanks for the sub!
is it very NOISY??
Not really, but does make the traditional Whoop noises.