Many must know in the early 60’s I help my dad just like many here tear apart cat dozers..sometime hydraulic-cylinders and other times the final drive on one side or the other.. I am from USA..I learn to work and I learned how things worked..Like any skill building confidence is very important for young people.. Nice work here all. It’s great to see. Hugs to the your youth helping here..
زملائي في مكة من الاخوه الباكستانيين منهم المهندس ومنهم الطبيب ومنهم الكهربائي وكذلك الميكانيكي .. هم محترميين جدآ .. وفقهم الله تعالى .. تحياتي لكم وبالتوفيق في اعمالكم اصدقائي ..❤❤
They didn’t forget, they probably just weren’t told to do it, I work with a lot of Indian and Pakistani people in Abu Dhabi and they are not prone to going the extra mile. They will usually do the bare minimum to look like they are working or completing a job or only specifically what they’re told to do.
Was hoping to see that they'd pull the Swing Motor and change that gear(not sure it get replaced without removing it). But looks like it didn't....until it makes a very bad noise again.
That looks like an expensive gear! I'm somewhat surprised that they didn't try repairing it by welding and grinding. Also was that water sitting inside the gear? Is there some missing drain or O-ring?
Mengganti swing GEAR kerja yang sangat berat.tapi masih d bantu dengan cren.tidak seperti yang saya buat,cuman bantuan 4 biji dongkrak.salam dari Riau Indonesia.
and yet itll still work without any issues... for godsakes it's a 7 inch thick swing bearing you salty, you were told a single dust speck gets in their and theyll be "catastrophic failure" lmfao privileged shit lmao btw you guys did great, just only thing is please be very cautious when going under the machine while it's in the air, on its arm. love from Canada 🇨🇦
I understand those guys have little to work with but why do they struggle to remove and replace the slew ring when they could've used another excavator to lift out the old one and set in the new?
swing bearing is the proper term. basically a stationary sprocket mounted to the track frame, which the swing motor sprocket rides that big sprocket and rotates the top piece aka house. ps called a swing bearing because it's essentially a bearing with ball bearings all around that gear.
Никакой воды не должно быть, там ведро солидола должно размазываться.... Без смазки один зуб начал крошиться и за ним дальше- больше. Причину появления воды нужно устранить....
Very funny Iam amazed in what the kid is doing and the kid is amazed in what the camera is doing or what the camera job is !!!!!they must be proud in what they do they are very talented people nothing is impossible!!!!!!!why no change the other piece too well nobody ask me. about safety🤫
Till two times "ouh" during tightening. They got three workers - small, medium and big and three pipes they put on wrenches, so they can get many settings 🤣🤣🤣
There was no need to hire the big crane here. The biggest machine they could use was a tlb only to move the undercarriage. I challenge you to save the cost and work efficiently and safe. We did that job in 12 hrs with minimum with only a TLB and 2 Artisans and 2 assistants
Culture of their work is more than terryfing! All done with flat wrenches. If they buy pneumatic one, job would be faster and could be done by three not by sevem or how many there were. Obligatory add sand to brand new element. Ant in the moments where more people needed work only one or two... I am surpised that they didn't weld it. But what with worn and broken gear? It will destroy new element really fast.
When SHTF these people will do ok.America on the other hand will be desparate to find someone that knows what they are doing.Key boards just don't get it done.
@@__-aleks-__ Неправильный! Этих детей порабощают, эксплуатируют, они будут обречены на жизнь в нищете и нищете. Только такой отсталый народ, как русский, мог считать это нормальным.
Many must know in the early 60’s I help my dad just like many here tear apart cat dozers..sometime hydraulic-cylinders and other times the final drive on one side or the other.. I am from USA..I learn to work and I learned how things worked..Like any skill building confidence is very important for young people.. Nice work here all. It’s great to see. Hugs to the your youth helping here..
👍
زملائي في مكة من الاخوه الباكستانيين منهم المهندس ومنهم الطبيب ومنهم الكهربائي وكذلك الميكانيكي .. هم محترميين جدآ .. وفقهم الله تعالى .. تحياتي لكم وبالتوفيق في اعمالكم اصدقائي ..❤❤
سيدي، أنا سعيد جدًا بهذا الفيديو وممتن جدًا لهذا الفيديو وأشعر أنه ساعدني في عملي ❤❤❤❤
Pajamas and flip flops. Standard uniform
beer nd plad. typical hillbilly uniform😂🤣🤣🤣
It's a pity they don't have an air tool to do all those nuts, and get the job done in half the time.
In the 60’s we had no air tools either.. but we torn apart dozer and fixed them..Great-way to build confidence and set up for life..
They forgot to replace the small drive gear, it's also damaged.
They didn’t forget, they probably just weren’t told to do it, I work with a lot of Indian and Pakistani people in Abu Dhabi and they are not prone to going the extra mile. They will usually do the bare minimum to look like they are working or completing a job or only specifically what they’re told to do.
Was hoping to see that they'd pull the Swing Motor and change that gear(not sure it get replaced without removing it). But looks like it didn't....until it makes a very bad noise again.
Чтобы резьбу не срывать- зовëм детей крутить болты
7:58 brave cameraman underneath the hanging cab section getting us our shots!
love from Canada 🇨🇦
you guys did a great job!
Can't imagine doing it without any power tools.
❤️❤️
That looks like an expensive gear! I'm somewhat surprised that they didn't try repairing it by welding and grinding.
Also was that water sitting inside the gear? Is there some missing drain or O-ring?
I think they cleaned it wit pressure water. Old ring was quite clean.
Mengganti swing GEAR kerja yang sangat berat.tapi masih d bantu dengan cren.tidak seperti yang saya buat,cuman bantuan 4 biji dongkrak.salam dari Riau Indonesia.
So, this is what child labor looks like?
Gotta love them steel-toed flip-flops.
ما شاء الله عمال مهرة ربي يبارك بعملكم وزقكم
A little dirt and grit on precision gears never hurt anything. Yikes!
Thanks for your opinion
Must be a paper pusher
and yet itll still work without any issues...
for godsakes it's a 7 inch thick swing bearing
you salty, you were told a single dust speck gets in their and theyll be "catastrophic failure" lmfao
privileged shit lmao
btw you guys did great, just only thing is please be very cautious when going under the machine while it's in the air, on its arm.
love from Canada 🇨🇦
I understand those guys have little to work with but why do they struggle to remove and replace the slew ring when they could've used another excavator to lift out the old one and set in the new?
All broken😆
Não trocar o pinhão que também estava danificado foi um erro...vai estragar a coroa nova.
👍
Why are the children used for labor and not in school??? 🙁
No work no eat. Simple as that
چرا برای بستن مهره ها از تورچ متر استفاده نمی کنید؟
it is that the called gear box of excavator? or not!?
It’s called the slew ring my friend
swing bearing is the proper term.
basically a stationary sprocket mounted to the track frame, which the swing motor sprocket rides that big sprocket and rotates the top piece aka house.
ps called a swing bearing because it's essentially a bearing with ball bearings all around that gear.
На воду похоже. Странно что нет отверстий сливных. Сверху вода попадает, надо куда-то сливаться.
Никакой воды не должно быть, там ведро солидола должно размазываться.... Без смазки один зуб начал крошиться и за ним дальше- больше. Причину появления воды нужно устранить....
Very funny Iam amazed in what the kid is doing and the kid is amazed in what the camera is doing or what the camera job is !!!!!they must be proud in what they do they are very talented people nothing is impossible!!!!!!!why no change the other piece too well nobody ask me. about safety🤫
Thanks for your opinion
Wwwwssaazeer44ru vbbbhji
A
2 31
! 4e2 31 31 31 31 43 g3 31 d3 d14 up
I wonder what torque setting they used on them bolts lol
Till two times "ouh" during tightening. They got three workers - small, medium and big and three pipes they put on wrenches, so they can get many settings 🤣🤣🤣
I love the smell of hydraulic oil in the morning😊
En la ciudad de vallarta la depesgamos con la misma maquina y 2 gatos atras en el contrapeso despues liberas el motor de transito para halarlo
Masya Alloh.....Luar biasa
There was no need to hire the big crane here. The biggest machine they could use was a tlb only to move the undercarriage. I challenge you to save the cost and work efficiently and safe. We did that job in 12 hrs with minimum with only a TLB and 2 Artisans and 2 assistants
Vietnam 🇻🇳🇻🇳🇻🇳 xin chào các bạn
Так же меняем на автокранах опорно поворотный круг.
Thanks for your opinion
Awesome guys ❤
Это большой труд открутить вручную ключами и прикрутить
Untuk jasa atau upahnya berapa pak
Where is that guy with stick welder, welding these broken teeth back up??
Good job my brother
صراحه فنان في شغلك
v The right tightening torque...?
It's just an opinion!
Good job 👌👌👍👍
Tetap semangat
What bearing did you replace lmao
whar these guys could do with decent tools...
Culture of their work is more than terryfing! All done with flat wrenches. If they buy pneumatic one, job would be faster and could be done by three not by sevem or how many there were. Obligatory add sand to brand new element. Ant in the moments where more people needed work only one or two... I am surpised that they didn't weld it. But what with worn and broken gear? It will destroy new element really fast.
This is Pakistan, do not expect any professional work
Minuto 17:30 ....no será mucha fuerza para esa tuerca..!!??
What could possibly go wrong?????
Torque specs, 14 year old 150 pound with a 5 foot bar😮
Máy đẹp đấy ❤
Good 👍
They got shit for tools, but no lack of tiny hands to turn out 189 fine thread bolts.
Ведущую не меняли?.
They like a rat repairing a pumpkin..
Tarnol mehran plaza Ali ustad ki dukan pe 😂
When SHTF these people will do ok.America on the other hand will be desparate to find someone that knows what they are doing.Key boards just don't get it done.
helllo you
Yes
What a tragedy: children working with dangerous chemicals and equipment.
🤲
it's better if they drink alcohol and take drugs and eat fast food with their parents money :)
Children made the phone you use and the clothes you wear
Эти дети не пропадут в жизни имея навыки в работе, они обучаются профессии.
@@__-aleks-__ Неправильный! Этих детей порабощают, эксплуатируют, они будут обречены на жизнь в нищете и нищете. Только такой отсталый народ, как русский, мог считать это нормальным.
Woahhhhh
Wrong title, should be "How do dot repair excavator". Can't see any "amazing skills" also.
Asiatic cowboys
Uhyf
Giao lưu kênh đi
Waste of time if you’re not going to fix the drive gear .it will soon fuck up
I guess 17:38 if I ever get to this place that will be my job!!!!!! 17:38 🔴🫢🤫
👍