Testing Abloy padlock PL350
HTML-код
- Опубликовано: 12 сен 2024
- www.lukuexpert....
www.lukuexpert....
www.lukuexpert....
www.lukuexpert....
Testing of ABLOY® padlocks shows that they resist attack and the severest of climatic conditions.
Abloy riipulukon testaus ja murtokestävys.
whb12fc12
![[753] You’re Doing it Wrong... The REAL Double Wrench Method](/img/1.gif)
After all that, he found the key....typical!!!
Nice padlock, but what really caught my eyes was the Heuer Front. Excellent vice.
Heaven forbid you lose the key.
I know for a fact that H.K. Porter 42-inch bolt cutters will only put the tiniest scratch on the shackle, and that's after the jaws have begun to deform and the handles are on the verge of breaking. And the scratch was practically insignificant, hardly noticeable. I've seen people try to cut one with bolt cutters on 3 diff occasions; you cannot tell them that it won't work lol, they have to try anyway.
42 dislikes from an IP address traced to MasterLock, Inc. ...
I just ordered one for my 16 year old daughters chastity belt.
I just bought a lock pick set. Challenge accepted.
+Lawrence H Good luck picking an Abloy lock.
Lee L good luck, those boys will find a way to get in there no matter what.
savage haha !
Well, as long as they treat her well the relative harm in having that one get stolen isn't that bad really. Maybe just buy a cheapo Master Lock and let the first locksmith to pick it open have the prize ;-).
My son tried to cut my Abloy padlock when I lost the key. The jaws broke on my expensive pair of 30 inch Record bolt cutters. It wasn't this model & the shackle was about 10mm diameter, but Abloy padlocks must be about the best you can get. A 5 inch mains angle grinder finally cut it, but as far as I'm aware angle grinders will cut almost any. My bolt cutters had a 1/4 inch chunk taken out of the jaws, so the padlock ruined them. Bit of a shame that my son is very strong & had one end of the bolt cutter handle against the ground for leverage, or the bolt cutters might have survived. Some padlock.
It seems the most expensive bolt cutters, like Kren 49 inch ones, probably might cut a 10 mm shackle on an Abloy lock, but they might not cut a 14 or 15mm Abloy shackle.I'd not risk ruining bolt cutters again unless they were cheap "throw away" bolt cutters, though Record is not an inexpensive brand & pretty good for most tools. Kren bolt cutters have little cutting edges than can be replaced, not the entire jaws.
Easier with a hand-held cordless angle grinder.
One of the best padlocks on the market.
@franck0011 it has an 15 millimeter hardened steel shackle so good luck cutting it with bolt cutters
Yes, really tough padlock. I would trust on it.
All this is beautiful. But now this days you can buy cordless angle grinder. I wonder how long does it take to break this padlock. ?
It might take a long time the shackle is real tough boron i have it so i can feel how hard is the shackle
It depends on how skilled the person is using a grinder (some people apply way too little pressure for fast cutting). And how powerful the grinder is. It may be possible to cut it off in like half a minute.
This is just unavoidable with a steel lock, as any kind of steel - hardened, alloyed or not - can be cut with a grinder quite easily.
Now THAT'S a padlock!!
ruclips.net/video/aiaOSf2sQxM/видео.html
They are not breaking the lock right way.
Impressive. Very nice. Let's see how it performs against the .27 purple strip Ramset...
Man "Dang it, there's the key".
They ARE awesome locks, but I want to see the exothermic lance test :)
That guy looked so defeated at the end.
Everyone in these comment says to test in angle grinder, but can i ask you? Is there a metal or any hard materials that can’t cut of grinder?
If this lock is protecting a real value and the chain holds an attack, just grind it. The trick is, protect the lock from grinding by take out the space for the grinder to reach. The only way to do it. If the value is high enough of the protected item, it's done in a jiffy anyway with PROPER TOOLS. Time and space is the real key here. When locking a bike, place the lock high, that is lack of counterforce for the bolt cutter and a dangling lock is hard to get a real hands on job on. The real key: PLACEMENT and SPACE. Sometimes it is better to cut the object the chain attach to.There.
I agree with others in the comments. Test it with angle grinders and high quality 42"+ bolt cutters, and we as consumers are able to compare it to others on the market.
Bob seemed rather disheartened.
I would love to have all the parts they throw away!
Dive into your local dumpster and wait!
It's not the lock that needs toughening. It's the hasp the padlock goes through
that's one tough .....vise
+Stephen Cunningham Lateral thinking, I love it 10/10
that's why everyone loves HEUER vises.. like really old ones still sell for a lot of money
A fine vice I've not broken yet lol
where is the Ramset test?
Poor guy - he must be knackered
I want that job :-)
NOW!!! For an Almax chain!!!
Well... good to know my lock will last 340 years
With these locks its easier to cut the metal around the lock than to break one, even a 1meter long crowbar will bend with 2 160lb people hanging from it.
Dont ask me how I know this :)
ruclips.net/video/aiaOSf2sQxM/видео.html
They are not breaking the lock right way.
Who uses a hacksaw like that
How if i lose the key ??
Well, for one thing a hacksaw operates in a different way. Just because a regular hacksaw can't get through it doesn't mean bolt cutters can't either. Take a tungsten carbide saw and the story will take a different turn. Take hydraulic bolt cutters and it will get through it. It takes about 13 tones of pressure, though.
Having a 341 Abloy padlock on shed guarding worthless yard tools has been doing just that, just realized key's been lost however. Could a grinder sporting a diamond wheel cut the shackle, tnx
The liquid nitrogen test ruined the cold chisel after less than a minute...
The PL350 cannot be cut with a 42 inch bolt cutter. Unless the user weighs 250 kilograms.
Great commercial for a bench vise.
What is the hardness of the shackle? Can you test it with a hydraulic cutter?
Can you test the PL321 ?
no bolt cutter test i see
I have tried and nothing happens I been building these for years and trust me bolt cutters are as much use as a butter knife
Well it has been over 2 years since I put that statement out. So I feel a video reply is the only real answer. How about a show down against a Squire SS65CS.
I'm talking about a physical attack. Same cores.
Sooo, when someone mangles the keyway and discs trying brute force attacks, you are now permanently locked out of whatever you put this lock on?
+TopherFM No you'd have to bring in welding equipment that's capable of reaching a temperature where you can actually cut through the bolt.
I'm sorry, but Mr Clean here has no idea how to swing a sledge hammer.
Was that an aluminium pipe he used for the torsion test? wtf
Entä rälläköinti?
No bolt cutter test? I would get this if it could survive some decent bolt cutters
Exactly, I have seen a video where the shackle of the Abloy 342 lock got cutted by a high quality 900mm bolt cutter that costed about 300€
Cutting torch is cheaper than 300 euro bolt cutters and works to any lock. Maybe it is just me but I don't really see a lot of point discussing about expensive tools needed to destroy the lock. If the lock is somewhere in less crowded place and the item you are protecting would pay the effort of getting 300 euro tools to access it then you need additional alarms and surveillance anyway.
I bet I could cut right through that thing with my cheap Chinese pair of 42" bolt cutters
@@Brute4rce1111 the problem is that the bolt cutters jaws need to be harder than the material they trying to cut, so from your description i would say that your cheap Chinese tool gonna fail miserably. Search on YT movie "Gerda Zircon 116 vs nożyce do cięcia prętów." its atempt to cut 6th grade padlock but i doubt this padlock shackle is made from much weaker material.
@@Bialy_1 I do agree that hardness does partly matter when we are talking about cutting tools, but in my experience, even though I have dented my 42 inch bolt cutters jaws, I was still able to "cut" the shackle. My theory behind this is that the jaws are only going to dent so far before they work hardened themselves to the cross section stress level involved in the cut. After that, the stress/strain of those competing alloys start to experience fractural toughness. And of course, the shackle being the harder metal, will fracture under the extreme narrowed force of the cutters head. It's kinda the same concept of a lead 223 bullet zipping through steel except the lead does not work hardened, it's simply the forces involved that really matter.
How about Biltema angle grinder?
useless
+Olivier Cauffopé If it's useless then why do they not test it? Other than that, this seems like a seriously strong lock. And some very serious testing.
Didn't you know? It works only on Biltema padlocks. What you need is an Abloy angle grinder.
smokyislay 😂😂😂
Por qué no hacen la prueba de corte con disco de miniesmeriladora inalámbrica?
I would have liked to see the sledge hammer against the lock at -196 C to see if it shatters.
I got to get this lock. Period.
Hi Alan, where you want this lock...if you are interested please mail me below id.
s.khan@technostream.ae
if you lost the key you order a replacement with the key card they give you.
Angle grinders.. I'm a joke to you?😎
Claw hammer, really?
Thieves are well known for hammer snobbery! " Eww Philip you brought the claaaw hammer, I simply refuse to hit anything other than nails with that. Next time being the 2lb ball peeeen. My gosh how can we ever show our faces at the Marquees's ball now?"
cek saya ge abloy mah alus ,poko na mah juara
I am sure my kids would find a way of braking it 😂
Lol I have this lock and if you make a noise anywhere near this the dogs will eat you before I do !
How many seconds will it hold against an angle grinder?
Grinder test will the one to see.
What about dropping it in boiling water or using a blow torch on it after being in the liquid nitrogen?
Most of these locks are used on semi trailer doors which do the job but if someone really wants it the can just cut a big hole in the door instead of spending hours trying to bust this lock
Mitä se tuumaa tälläsestä akku käyttösestä leikkurista ? Siis porakoneen näkönen mutta sellasilla leuvoilla leikkaa 16mm harjaterästä ku juustoa !
Harjateräs on pehmeätä.
Bolt cutter/angle grinder test and you will have many sold!
David Chan lol an angle grinder would get threw that with no bother. 10 second job at the most. You would of thought they'd of made it angle grinder proof, before they made it luquid nitrogen proof.
That is a retarded ass statement. angle grinders and shit? have you ever used a torch or angle grinder at night? you can literally see that shit for miles and hear the grinder for almost as much. would kind of be weird for 3 am now wouldn't it.
iceman27406 you can guns, atomic bombs & ban saws at night. They made made it "all of them" proof
if you're going to be using angle grinders you might want to opt for cutting away the hasp/shackle/hinges/door/etc.
If I remember certain acids work quite well !!!
Nope it doesnt work in this lock i ever tried
lets not forget the gas cutoff saw, pretty sure thats not in any official test and considering that its not really a quiet tool in any sense, esp with 5-7.5 hp of 2 cycle engine,its still regarded as the universal key for one time use. stealth=0 however, unless in the proper outfit and gear though:)
Yes, I'm convinced let's go spend 160 moneys to buy this.
Why was there no bolt cutter attack?!
Simple violence will not do the job. Better use brains to find weaknesses.
The disks in locks like these are held in place with a thick bottom plate, which is pushed in tight.
In some locks this plate can be pulled out, so all lock parts fall out.
You would have to make a pulley which locks into the locking disk, and then starts pulling.
how well would this lock do under this attack?
The bottom “plate” in these beasts is a several millimetres thick threaded insert (with a small screw “hidden” behind one of the legs of the shackle to prevent one from unscrewing it while the lock is locked. So no luck on that end, either. (When open, and after removing the locking screw, the threaded insert is opened with the blunt end of the key... but unfortunately there is no Integrated screwdriver in the key to open the screw so there is still at least one thing they could do better for fully tool free disassembly for legitimate users ;-)
I noticed that nobody ever attacked it with heat... Not many blokes are walking around with liquid N2 but lots of folks have small portable oxy-acetylene cutting rigs... Even if you could just heat a section of the shackle enough to ruin the temper so it could easily be cut. Also, I might point out that the chain or shackle has to be just as indestructible or the lock is no good.
Sure, no lock is indestructible. Attacking it with heat usually takes time, however, unless one brings uncommon tools like a portable induction heater. And it's conspicuous.
For Abloy cylinder locks (I don't know if they also fit the padlocks - probably not) there are even special carbide tipped milling bits. With a powerful cordless drill, they can drill open the lock in seconds:
ruclips.net/video/uj4myR2XlWc/видео.html
sera que vende este cadeado no #brasil
Or you've got 2 people weighing 125 each. ;-) Thanks for the info!
How to cary this pad lock when im use superbike and not using any backpack..do u have a holder for this pad lock?
You're fucked
Where can I get that hacksaw??!🤣😂
give me a 1/16 abrasive disk on a grinder and 10 seconds
5:00 this is very dangerous for his face if the loch explodes!
That's a bull shit way to saw.....but you should try a cutting torch
At using a bolt switch. Does not stand
who needs to go back to school ?
"160 moneys" ?? wut ? LOL!
I use a oxygen acetylene rig anytime I lose a key to my locks.
What about hydraulics perhaps a spreader like the firebrigade use
+JAMIE NEWMAN That's what the first test is about.
With such tools, one can break pretty much any lock.
The first pull test in the video shows it breaks at about 90 kN (9 tons) of pulling force. Most hydraulic tools are much stronger than that.
It may even be that some pretty primitive attacks could rip it off. I'm thinking of threading a Zylon rope through it - it is more stiff than a steel cable and a 10mm rope holds 14 tons, attaching a big piece of metal to it (like a 45 pound weight plate) and slamming it down to yank on the lock.
Will it stand up to a seriously professional picker like bosnianbill? I've seen lots of tough locks that were easily picked by a pro or a lucky thug. In my opinion, if it can be picked, all of that toughness is a waste of time and effort.
*****
Okay, thanks. : )
yeah I only know of classic being picked good luck with disc lock pro and protec ,protec 2 and novel
*****
Thanks, I'll check it out.
Definitely cant pick this, because it has completely different kind of mechanism with those discs (is it 16 of them). I have seen a tool that was made to pick abloy locks though.
he said himself that he can't and does not know anyone who can pick protec2. And if someone knew how to pick protec 2 they would most likely not be some thief but rather a CIA guy or something in that direction. Protec2 is quite overkill for locking up your goods, most criminals are nutjobs and don't even bother picking because they don't know how. They just smash and destroy everything but the cylinder.
Battery disc cutter = job done
Алмазной коронкой(качественной) высверлить шайбу личинки , за 3-5 минуты , и вуаля.......
yo corté uno con esmeril en menos de 60 segundos no son tan seguros
Useless lock.... you can just drive a semi through the building and boom you're in. Try harder.
not sure if troll or stupid
Why_not_both.mp4
Like s Boss!.......❤️👍
i want to see attack with solid breaker bar AND sledge hammer applied to breaker bar.
Wow
bagus
Lock picking lawyer can open this with his eyes 👀 closed 🤪
I think this is one he can't. If he can reliably and quickly pick an Abloy Protec2 core open, that would be utterly sensational. As far as I know, no-one has yet been able to do so. There is possibly a way to decode the lock with some very specialized tools, but it's a lengthy process that could hardly be described as "picking" anymore.
4:58 is that is this guy's day job one think he'd be built like a shit brickhouse.
if u lost the key WTF
A Milwaukee 0725-21 28-Volt 4-1/2-Inch Grinder/Cut-Off Tool,will cut this like hot knife through butter.
A 42" bolt cutter will slice that shackle off
+smokeya2 No way in hell .
bolt cutter are useless with 14mmØ shackle
fuck off will it I build these things of a living they are the best padlock on the market
abloy is the hardened lock I ever use...I already trying with bolt cutter....but still same...
3:56 This is fake. Nobody can move that fast. Sound changes too. Not natural...
I hope youre not serious
No you can't with angels greniers but your welcome on the new Assa Abloy Fan Group fb.com/groups/assa.abloy.fan
i have, i'm happy
I had one, used a 20 oz framers hammer and it broke
How and where did you hit it?
very strong stuff.. can i have one for free? hehehe
I had one of these securing my motocross bike. The twats got though the ground anchor. Dragged my poor old bike off with the chain and padlock still attached.
What you mean? The chain cut instead of lock?
@@olinellngbuk1871 No the chain and padlock were still attached to the bike. The broke the ground anchor and could not brake the chain and padlock.
Lost key??
its over
No lock can resist a good angle grinder.
It's going to take several minutes though, and it will be awfully noisy and flashy in case you were planning to break the lock stealthily.
try aquaregia(hno3 hcl) for silent ones?
XD XD
angle grinder......
useless
The awful truth of padlocks is that the angle grinder with a zip disk - OBSOLETED EVERY PADLOCK. And now with ni-cad and li-ion batteries, cordless angle grinders are totally portable. Buy a 12 gauge at Cabellas.
Even this one? You sure about that?
Hahaha tools are very useful the thing is that also thief's can use it.. like a gun is safe to protect you.. but criminals can use it too... It's complicated.. use some pair of padlocks and they will search some better and easy option.
could've just drilled out the key hole useless tests
Or fill it with used gum and small sticks. Useless tests.