An old Moa trick is - Take and empty Tylenol bottle or something like (needs to be similar diameter of the motor)that and cut both ends off it. Then cut a slit down the side to remove some of the wall to allow clearance . Then little dab of shoe-goo …And BAM! Ya have a motor skid plate. Slides easier over rocks and protects motor.👍🏼😎
0:57 to 1:09 Ya know, a plastic coffee can lid cut to fit and some Shoe Goo on its roughened surface could be glued to the servos & motors and act as skid plates to protect both servo and motor casings. They won't last forever, but they'll slide better than steel/alloy and they're certainly cheap enough to make several that should work for multiple sessions each. I've used coffee lids and gallon Ice tea jug plastic many times as sacrificial skid plates on my RC trucks.
To me it looked like the rear needs more flex to keep the rear planted down but not driven one of them shoot the closet thing I got to that is night crawler by losi
I think I would come up with some type of skid or something search around to try to protect them battery in that motor and Servo I'm sure somebody's made something
I can tell ur not used to the technical tx/crawler yet, as in not AS comfortable with em as 'the ppl u see on RUclips' are. Give it some time. Those ppl have had theirs for a lot longer.
An old Moa trick is - Take and empty Tylenol bottle or something like (needs to be similar diameter of the motor)that and cut both ends off it. Then cut a slit down the side to remove some of the wall to allow clearance . Then little dab of shoe-goo …And BAM! Ya have a motor skid plate. Slides easier over rocks and protects motor.👍🏼😎
That’s a pretty smart solution 🤙🏻
On a couple of the lines you was struggling with try using the rear dig and push the front where you want it instead of trying to pull the rear
This has to be your favorite crawler
0:57 to 1:09 Ya know, a plastic coffee can lid cut to fit and some Shoe Goo on its roughened surface could be glued to the servos & motors and act as skid plates to protect both servo and motor casings. They won't last forever, but they'll slide better than steel/alloy and they're certainly cheap enough to make several that should work for multiple sessions each. I've used coffee lids and gallon Ice tea jug plastic many times as sacrificial skid plates on my RC trucks.
Awesome crawl Joe!!!👊
Imagine this thing with 4WS.
HI JOE IT MUST BE FUN HAVING TO LEARN TO DRIVE THIS AMAZING VEHICLE SIR 🇬🇧🇺🇲✌🏼🤩👍🏼
To me it looked like the rear needs more flex to keep the rear planted down but not driven one of them shoot the closet thing I got to that is night crawler by losi
That was some intense 📐 finding. ✨🏆🎥🏆✨
I'm aware of proline ibex but what are these tires again?
Dlux 2.2s
Well that looks fun.
Morning cool rig
I almost wish i had gotten one or built one
I want one so bad but they're like about 2,500 to $3,000 but I would like to see you about the Rock's competing with it I really believe in you
rc4wd has the bully 2 as a kit without electronics
I'm not a big fan of crawlers but that was pretty impressive 👍🏻
I think I would come up with some type of skid or something search around to try to protect them battery in that motor and Servo I'm sure somebody's made something
I would think if you would turn left it would raise up rear end up and drag it around
👍😁
My goodness the word mercenary is getting thrown around a lot today LOL
I knew you would eventually go to the dark side that's the new definition of a cheater rig
Ppl usually aren't fans at what there not good at knowing those lines can be difficult
Mic is a bit loud, can hear all the little weird breathing your doning while driving lol
I can tell ur not used to the technical tx/crawler yet, as in not AS comfortable with em as 'the ppl u see on RUclips' are. Give it some time. Those ppl have had theirs for a lot longer.
Can you make that thing not talk?