I have a 2011 Fusion SE 2.5 as a daily. Bought it new back in 2010, just hit 220k miles. Here are the things I had to replace; 2 Batteries, PCV valve, valve cover gasket, oil pressure sending unit, coolant outlet, and here shortly I’m going to replace the thermostat and engine/transmission mounts. I’ve done all the maintenance and repairs. Pretty solid car.
@@abbasmo1580 about $500 worth of parts and I did the repairs myself. Just hit 240k miles. I had a Civic and transmission went out. Few months later, timing belt gave out and engine went to sh+t.
Mine completed 160000 mile today. 2011 Ford Fusion SE - 2.5L FWD. Major repairs, breaks (3 times), tires (3 times), 3 pulleys and a drive belt. Front Sway links, all the filters have been changes 2-3 times, major light bulbs have been changes once, still on original wheels and floor mats, wind screen and no transmission oil change. Synthetic Engine oil changed at every 5k-6k miles. Car is on 2nd battery. And has an engine light on for Purge Valve, due to filling the tank full all the time. Driven in Toronto winters but still has no rust on body. Underbody is neat and clean. Runs like a dream.
I have a black 2011 SE This is the best car I've ever bought. I bought it for 900$ 86,000mi and had it for 3 years and I haven't had to change anything major just breaks, a belt that a rock popped in, reg. Oil changes, normal maintenance and a couple light bulbs and now about to get a tune up.. I've traveled to 3 states and traveled statewide. Hands down best ever. This car is perfect, I just wish it was a standard shift not automatic but it's still my baby ❤ I love it..
I have a 2010 Fusion SE. Absolutely no problems. I did some preventative maintenance: changed the idler pulley to the three point of connection upgrade, changed the TB (because of the recall/TSB), Changed the tensioner pulley bc of whine, and added a Steeda Swaybar and strut tower brace. Also replaced the HVAC blower because of some chirping noise. Replaced the battery. Never had a problem with the 6F35 trans. I change the Mercon LV out before it turns brown/black. Both driver's and passenger airbags have been replaced due to Takada recall.
I just got and I am proud to say that I'm a owner of a 2010 SE Ford Fusion with that same engine. And so far so good. I do agree that the fuel efficiency is way off way off. But I enjoy the car it has a lot of room. I do agree that if the car wasn't so heavy it will be a little faster. But I am most definitely looking forward to taking my car out of town with the mileage that it has on it, 125,000 plus miles. The only thing I've done thoughts far as change the oil and had the recall about the airbags done. But we will see this is 2022 so I most definitely have to figure out you know what's what. But I did do a Carfax report on my vehicle and there were no accidents and they did the regular scheduled maintenance on the car so the car was very well-kept. Actually, if I had to rate this vehicle so far it gets a number 10 for me.
I've got a 2010 model SEL 2.5 Tuxedo Black, Navigation, Sony music box, tan leather. Bought from original owner @ 126k. After almost 5 years she's @ 213k. Best car I've ever owned.
Bought a 2006 fusion SEL with 2.3. Drove it for 5 Years and fell in love with it. Wanted a 2015 body style but after driving it, I felt like it was trash. (2015 1.9l). Found me a 2012 with the 2.5 and it was like love all over again. I drive that car like crazy and love it.
100K on my 2011 SE Fusion. It also hard shifts when cold. No biggie. I do change fluid every 30K though, regardless what Ford says. Thanks for sharing your experience. Good Video.
Couple of things to note the 2.5 l engine yes it's low on power but it sure beats the 2.3 that it replaced before hooked up to the 5-speed transmission. Also I had to replace a water pump if you ever do that make sure the person knows what they are doing because that water pump is typically seized up in there and they have to apply heat to get it out just don't let them get a crowbar and start beating it out. The transmission issue you were talkin about is a common issue with the six f-35 my 2015 Ford escape with the same transmission does the same thing you just have to let the transmission warm up for a few minutes and you're good to go. Great video I wish you had more info on the radio I would like to put that kind of radio in my 2010 Ford Fusion hybrid. I really like your double DIN cover. I have a Ford Fusion 2010 hybrid the difference between mine is it is an Asin CVT transmission the engine is a 2.5 Atkinson cycle engine. It has 160,000 miles on it and shows no signs of slowing down.
@@filipetavares3413 just normal maintenance, oil change every 5K and every 30K transmission fluid drain and filled. Drain and filled my coolant, I need to do that again. Other than that I went through 2 set of brakes and one set of plugs. Valve cover gasket.
266k miles on my 2011 2.5 SE. never had it in the shop ever, not once!!! Daughter wrecked it day after she got her license, but I drove another 6k miles climbing over the seat since driver’s door was crushed. Best car ever. Bought a 2012 with 80k on it after that. Still going strong.
Mr. Brotherly Review: Nice video and review.....I know this vid is a year old but I am going to comment, Bought a 2010 Merc Milan Premier with 18 k in 2012 3.0. v-6 This vehicle along with the 88 Merc Grand Marquis LS are two of the best cars I have ever owned. 72 yrs old... Took 2yrs for the airbag recall to be resolved on the Milan waiting for parts.Another recall was the led Milan tailights. Ford replaced under a recall. Bad LED connection insides the taillight assembly. thats it. I am changing oil like clockwork,never more than 4k between changes. 5 w20 full synthetic. Valvoline. Trans service, airfilter etc. I do pull the throttle body and clean every 20 k. Vehicle has 86 k and runs and drives like new. I know 86 k is not a lot of miles but just an excellent car, 30 mpg hwy at 65 mph 23/24 mpg local driving Yes I like Mercury Had a 2000 sable with 200k body started to go.. Figures Mercury is no longer so long
Thank you for sharing, I have a 2012 Ford fusion and I brought it in2014 I have driven it daily and my Son was going to colledge and he drove it a year or two, I had to put a pulley a drive belt and the drive belt was in the last month ago the only downside of this car was the air conditioning, I haven't figured out what it is yet but I had a friend to bypass it and it will literally make you cut it all the way down because it will get that cold, I honestly can say I brought it in2014 and I still drive it daily no problems, a great car that has been good to me and my Family
I had to replace the idler pulley and belt also. The only issue I had with the a/c was the blower motor under the glovebox would occasionally have to be kicked for it to turn on. Had to replace a wire on it. Cheap and easy fix.
I used to have a 2011 Mercury Milan Premiere. I got the car in late June 2012. It had a little bit over 11,000 miles on it. I totaled the car by hitting a deer the 2nd time in early December 2016. It was a good car to drive in. It was the same as a Ford Fusion inside. I did wanted a Ford Fusion in 2012 that was a year old car. The dealership had about 5 of Fusions but, had almost 40,000 miles on them even a little bit higher price. I choose the Mercury Milan which had lower in mileage and even the price,too. It was my 1st car with Bluetooth and Satellite in it. Even the first with a keypad on the driver’s side door. I knew how to used a keypad on a Ford vehicle because my parents had it on their vehicles from Ford. When I first test drove the vehicle that I really liked the ride. My parents even liked driving the car,too. They did took turns in driving it. I got used to it by riding it. Right now that I’m driving a 2020 Ford Escape SE in black. It is my 2nd Ford Escape. I used to have a 2015 Ford Escape but, it died on me. Before the Milan that I used to drive a 2005 Ford Focus ZX5 with SES trim level. I had that car for almost 7 years till I was in a bad car accident in early March 2012. I broke my left ankle in that accident. My first car was a 1998 Ford Contour SE that I gotten in mid October 1999. I even gotten my driver’s license in that car in mid December 1999. I had the Contour to late May 2005. I’m into Ford vehicles since I was little. My mother used to drive a Ford Pinto which was the most dangerous vehicle from Ford. My mother was a very safe driver.
I have the 07 model 2.3 liter backed by the Mazda 5 speed automatic. Just normal maintenance, at 120,000 I replaced all brake pads and rotors front struts and rear shocks , right lower ball joints the left side was done at 102,000 , and rear hubs and the valve cover gasket and plugs , has 142,570 miles oh and because of winters I replaced the left rocker panel. I don't care what vehicle you own after a 100,000 miles it's normal to replace these mentioned above unless an individual does a lot of highway driving, I live in Michigan so the combination of bad roads and winters I'm very impressed with the reliability of these cars.
I have a 2012 Ford Fusion 2.5 I4 with 90K miles on it. Runs like a champ and I take care of it in every way I can. Still has almost all original parts and I've only put about 200 dollars into it so far.
I bought a 2012 ford fusion SE. Had 115 miles on it when i bought it In 2021 and recently lost it 😢 it got totaled. I miss it very much. It was a very good reliable car. Had no problems with it. Just got the brakes done, tires and obviously oil changes..
Our 2006 Chevy Cobalt just had a fatal heart attack (timing chain, for those who know😢). We are absolutely stuck with needing a new vehicle right now this second. Knowing these dire circumstances, would you still recommend a 2010 fusion? So far everything looks aces on reviews. Complaints appear rarely. People LOVE this year in particular. Thanks to anyone who can respond!
I swear that 2.5 I4 engine is up there with Toyota reliability, along with the Buick 3800 V6 engines. I'd definitely recommend any vehicles with these engines as daily drivers. Great review. I definitely want a 2.5 Fusion.
I agree. I’m a little over 220k in my 11’ SE 2.5, bought it new. Minimal issues that I can count on my hand. PCV valve, oil pressure switch, valve cover gasket and coolant outlet.
Had to replace the front driver side shaft and support bearing plus seal 🦭 left and right , and belt tensioner over the years but a great vehicle, I’ve had all the good ones in the past in the seventies, Mustangs , Chevelles , Dodge , Chrysler and this is the best car I have owned .
@@BrotherlyReviews Yep, same with a Lexus ES330. The intake plenum is bolted in the back to some brackets right up against the firewall...super hard & frustrating to get to. I think the engineers design things like this on purpose so owners don't work on their own cars. They want you to bring them to the dealer service dept.
I have a 2012 eel fusion 2.5, so reliable I got it at 17 and at 21 I put 30k miles on it easily and only had to do the brakes, valve cover gasket as well as the whole front suspension with cv axles but the suspension was still solid for the most part. Amazing vehicle for a daily if the transmission and engine goes I’ll most likely just throw in a new drivetrain
I have a 2012 SEL, and it does me just fine. The thing will go when needed, no issues passing someone or merging. For a 4 cylinder its above expectations and the gas mileage is fantastic. I can make $120 door dashing and spend $20 in gas 😂
I like your vid. I have a 2017 se 2.5 l. In the mornings after the engine warms up, I drive down the street, stop, make a turn, and after the first shift it feels like it slips but after that it works fine. The fusion 2.5 is the most solid car wish it was faster like you said but it’s a sacrifice between reliability and power.
The most common problems for these cars are fuel pump issues, because there built into the the camshaft (genius idea right?). Anyways, that slipping could range from transmission all the way down to a faulty spark plug.
Hey man! Nice review!! I really like that body style of car. It’s very good looking. Today, I picked up a 2012 Lincoln MKZ! Pretty kick ass comfortable luxury car. I sold my bright red BMW X4 M sport for it, it was just too expensive for me. I had it for over a year, and I always had to live so financially tight, that I couldn’t have any spending money. I got sick of that, so I picked up the Lincoln, for a great price. It’s a really good car. I plan to keep it for a long time. I wanted to ask you, you said you had the 2 L engine, which has been very reliable, I’m glad to hear that. Is the 3.5 L V6 engine reliable? That’s what I’ve got. Thanks!
Same car. Only mine Is SEL. No spoiler had the entry / lock keypad. Same style Same light display. Different rims. After 8 years. Having to replace the tranny lines to radiator. But these ford's MOVE. Over 90 they become loose. Mines dual exhaust and double catalytic converter. But man. Same body and all. My miles are way less for a 2011. Like 85000. Mines fully loaded. But you got a good ride. As soon as I fix mine up. Prolly trading it in.
Look for the 2011 if you can. 2011 and 2012 had some differences with the steering wheel controls, and none of the 2010 models have automatic headlights.
Awesome video man, I am actually looking into buying this car right now! Can you tell me the details for the Apple Carplay unit you're using to get all those features? I think in the video you said Maestro RR, just want to confirm
I’m looking at a 2011 Fusion SE , the car has 179.000+ miles on it The car does have a little Rust towards the rear of the vehicle but not bad , it’s either the Fusion or a 2012 Focus SEL with 117.200 miles which is in better condition than the fusion I’m looking at, both cars are being sold for super cheap I’m undecided about which car I’ll buy, I don’t drive around much I do that at work (Amazon Delivery) lol I’ll only be using the car for transportation from home to work.
I have a question.. i just recently bought this exact car and I had a 2017 nissan altima with a back up cam, and i was wondering where did you get your screen/carplay? Thanks for the vid!!
The brand is called Pioneer NEX. Ordered from eBay if I remember correctly. There’s a ton of different ones. Just make sure it’s an NEX model if you want Apple CarPlay/android auto
PCV Valve need to be replaced but is located behind the intake that has to be removed and as I understand should be replaced every 30 thousand miles Don’t you just love it
What issues are you having? I only know they’re notorious for engine failure if you don’t replace the water pump on time, but that’s about it. Most engines will do that.
i had a 2010 fusion hybrid i loved that car but dumb me i gave it to a family member that needed a car and now i wish i would have keep the car never and any problems with it and it had 150,000 miles when i bought it and it had 201,000 miles when i gave it to a family member and the car was still running great
I bought a 11 fusion. Has 191k on it right now. Backing up has some clicking but worse on sharp turns and does it at first forward moving and goes away. Rides awesome and reliable. CV axles maybe?
I have a 2012 ford fusion SEL AWD with 119k have had it for 8 months and love it just put magnum flows on it and getting ready to put an intake on it trying to improve the gas mileage only get 20 mpg on the highway
Like that you got the newer factory 2012 wheels on yours makes it look like a genuine 2012 model now compared to the cheap bolt on covers the 2010 and 2011s had on the SEs
@@BrotherlyReviews I own a 2010 Sport in silver with the bolstered leather interior with the blue racing inserts. Was my Dads brand new originally. Ours has never seen a winter and is always stored. Has low miles 23k and is very fast with that Aisin T80 6spd and 3.5 DOHC 24V Cyclone High Output V6. Love these cars
@@BrotherlyReviews yours is very nice and you're correct the Mazda 2.5 Inline 4 is super reliable engine they also used that in the Escapes and Rangers of that same era. In which we had a 2007 Ranger base never any issues
@@evanlovestdwp his might have that as an dealer negotiation added accessory. Weird cause the SE is a mid trim level and they all mostly came with that standard. Then again I see some SELs that also didn't so depends how it was ordered. Only model that came with everything was the SPORT and that trim was its own trim!, yet I see some SPORTs that dont have moonroofs and seem just as stripped down as a base SE with exception of the High Output powertrain all SPORT models come with as standard equipment
@@BrotherlyReviewsI got a 2011 3.0 for my Turo fleet. I stayed away from the 3.5 due to the design where the water pump is internal. I don't want maintenance being that difficult for a part that should be semi easy to change out should it go bad. With the internal water pump you're just asking for trouble.
@@BrotherlyReviews found a much better deal. Bought a 2010 with 62K mikes for 6K. The car is in great condition. Going to get it detailed over the weekend.
huh. toyota fan but maybe picking up a family owned fusion 2010 SE in great shape, from California, with 46K miles. N0t sure of price yet but kBB around 6-7000 private party value. But concerned about transmission/steering problems among other things..it being a Ford. but maybe might be good for the kid for the next 4 years of college.
I have a Fusion 2012 3.0 V6. I just upgraded my turn signals to syneticusa. I am looking forward to replacing high beams with H7 LEDs but I don't know if the dust caps would fit back on with LED lights. Could you share which high beam you use and whether you had trouble with putting dustcaps on afterwards?
I bought my 2010 SEL 2.5L with 66k miles a year ago and I love it way better than the malibu I used to have. Are those the stock fog lights or did you buy them?
Can you share the link for the head unit that you changed to get apple car play - im considering buying one of this and apple car play is a must for me - if you could share the link, pricing and installation details, woulds be really helpful
Where did you get the underglow lights? they look really nice on the interior, the 2017 Ford Focus SEL came with an integrated underglow interior lighting system which i really miss tbh makes the car look nice at night, where did you get the ones the fusion have?
@@BrotherlyReviews are they easy to install? Ive heard missed reviews especially in regards to the adhesive alot of people say to get aftermarket adhesive cuz the ones that come with them suck and they be Fallin off lol
The ones I have use 3m tape on each of them. I’ve had them for about a year now and haven’t had any issues with them. I’ve even moved them around a couple times and they still stick.
My town car weighs 4300 pounds and has a 4.6 tops out at 104 mph with 280 hp and that fusion will smoke my car man I'm thinking about fusion or a Sonata
I want to purchase this 2010 Fusion Ford SE card with 198K miles, its $3200. Is it worth it? It's had only 1 owner and he claims hes kept up with maintenance, im just nervous.
Sorry for my delayed response Do you know what engine it has? 4 or 6 cylinder? If it has the 4 cylinder then that’s the best engine for reliability. I would definitely get the maintenance records before you purchase, to make sure .
I think the 2010 - 2012 fusion is worst used car you can buy because of the eletric power steering issues. I think it's like rolling the dice with one of these cars...
@@BrotherlyReviews had the 08 2.3 fusion love it so I jump to the 2012 from there I think that's the final best of the fusion........fallow up for me.....
@@BrotherlyReviews future common issue is battery pole connect valve cover gasket....maybe alternator or water pump....change thermostat now and your safe....drill a 1/4 inch hole on thermostat before in stall to safely take out air bubble or air packet.... That about it... Change all oil to time...
The 6F35 is a transmission known for failure, but a lot of it also has to do with maintenance. Mine would occasionally slip between either 3-4 or 4-5 gears when I first start driving it, but once the trans fluid reaches operating temperature, it doesn’t do it.
The trans in the 2.5l and 3.0 are known to give issues, but like most cars it’s due to lack of proper maintenance. Mine had 225k when I sold it and no issues with the trans. I always drained and filled the fluid once a year.
I have a 2011 Fusion SE 2.5 as a daily. Bought it new back in 2010, just hit 220k miles. Here are the things I had to replace; 2 Batteries, PCV valve, valve cover gasket, oil pressure sending unit, coolant outlet, and here shortly I’m going to replace the thermostat and engine/transmission mounts. I’ve done all the maintenance and repairs. Pretty solid car.
They’re great cars. Will definitely get another in the future.
@@BrotherlyReviews Gotta watch out for the electric power steering
Recall was done before I bought it, thankfully 🙏🏾
solid my ass, look at what you had to replace now comparethat to camy or civic
@@abbasmo1580 about $500 worth of parts and I did the repairs myself. Just hit 240k miles. I had a Civic and transmission went out. Few months later, timing belt gave out and engine went to sh+t.
Mine completed 160000 mile today. 2011 Ford Fusion SE - 2.5L FWD. Major repairs, breaks (3 times), tires (3 times), 3 pulleys and a drive belt. Front Sway links, all the filters have been changes 2-3 times, major light bulbs have been changes once, still on original wheels and floor mats, wind screen and no transmission oil change. Synthetic Engine oil changed at every 5k-6k miles. Car is on 2nd battery. And has an engine light on for Purge Valve, due to filling the tank full all the time. Driven in Toronto winters but still has no rust on body. Underbody is neat and clean. Runs like a dream.
I have a black 2011 SE This is the best car I've ever bought. I bought it for 900$ 86,000mi and had it for 3 years and I haven't had to change anything major just breaks, a belt that a rock popped in, reg. Oil changes, normal maintenance and a couple light bulbs and now about to get a tune up.. I've traveled to 3 states and traveled statewide. Hands down best ever. This car is perfect, I just wish it was a standard shift not automatic but it's still my baby ❤ I love it..
Would u recommend it? I'm looking to buy one
@smileyk4129 absolutely recommend!
I have a 2010 Fusion SE. Absolutely no problems. I did some preventative maintenance: changed the idler pulley to the three point of connection upgrade, changed the TB (because of the recall/TSB), Changed the tensioner pulley bc of whine, and added a Steeda Swaybar and strut tower brace. Also replaced the HVAC blower because of some chirping noise. Replaced the battery.
Never had a problem with the 6F35 trans. I change the Mercon LV out before it turns brown/black.
Both driver's and passenger airbags have been replaced due to Takada recall.
I wanna add a few Steeda parts to mine too. And I change the fluid once a year. I’m about due to change it again soon.
I just got and I am proud to say that I'm a owner of a 2010 SE Ford Fusion with that same engine. And so far so good. I do agree that the fuel efficiency is way off way off. But I enjoy the car it has a lot of room. I do agree that if the car wasn't so heavy it will be a little faster. But I am most definitely looking forward to taking my car out of town with the mileage that it has on it, 125,000 plus miles. The only thing I've done thoughts far as change the oil and had the recall about the airbags done. But we will see this is 2022 so I most definitely have to figure out you know what's what. But I did do a Carfax report on my vehicle and there were no accidents and they did the regular scheduled maintenance on the car so the car was very well-kept. Actually, if I had to rate this vehicle so far it gets a number 10 for me.
I've got a 2010 model SEL 2.5 Tuxedo Black, Navigation, Sony music box, tan leather. Bought from original owner @ 126k. After almost 5 years she's @ 213k. Best car I've ever owned.
How much did u get her for?
Bought a 2006 fusion SEL with 2.3. Drove it for 5 Years and fell in love with it. Wanted a 2015 body style but after driving it, I felt like it was trash. (2015 1.9l). Found me a 2012 with the 2.5 and it was like love all over again. I drive that car like crazy and love it.
I have 2009 Ford Fusion V6 SE- Tuxedo Black. 284,000 miles. Be a great car. Typical maintenance. 2009 was a recommended buy.
Just purchased ford fusion SE 2012 163k miles on it . Runs great😊 👍🏻
I currently have a 2012 Ford Fusion SE and I am at 122k miles and it runs so good. Keep oil changes and she has been very reliable. I love this car.
Get read to replacing the PCV Valve located behind the air intake and also discover my cat is clogged at 104,000 miles
100K on my 2011 SE Fusion. It also hard shifts when cold. No biggie. I do change fluid every 30K though, regardless what Ford says. Thanks for sharing your experience. Good Video.
Thank you 🙏🏾
Couple of things to note the 2.5 l engine yes it's low on power but it sure beats the 2.3 that it replaced before hooked up to the 5-speed transmission. Also I had to replace a water pump if you ever do that make sure the person knows what they are doing because that water pump is typically seized up in there and they have to apply heat to get it out just don't let them get a crowbar and start beating it out. The transmission issue you were talkin about is a common issue with the six f-35 my 2015 Ford escape with the same transmission does the same thing you just have to let the transmission warm up for a few minutes and you're good to go. Great video I wish you had more info on the radio I would like to put that kind of radio in my 2010 Ford Fusion hybrid. I really like your double DIN cover. I have a Ford Fusion 2010 hybrid the difference between mine is it is an Asin CVT transmission the engine is a 2.5 Atkinson cycle engine. It has 160,000 miles on it and shows no signs of slowing down.
Thanks for sharing, great video. I agree with you, fusion are very reliable vehicles. I have a 2010 with 205K. Mostly just routine maintenance.
U never had problems with transmission or the power steering ??
Trans does act a little strange at times, but only when it’s cold. After it warms up it shifts fine.
@@filipetavares3413 just normal maintenance, oil change every 5K and every 30K transmission fluid drain and filled. Drain and filled my coolant, I need to do that again. Other than that I went through 2 set of brakes and one set of plugs. Valve cover gasket.
266k miles on my 2011 2.5 SE. never had it in the shop ever, not once!!! Daughter wrecked it day after she got her license, but I drove another 6k miles climbing over the seat since driver’s door was crushed. Best car ever. Bought a 2012 with 80k on it after that. Still going strong.
I'm tempted to buy one that has 87k Mike's for 5k. Do y'all think it's a good deal? Is the car reliable? It's a 2010
I got mine 256,620 miles! FORD FUSION 2007 SE 4cyl.. Rock&Metal as long as you maintain well and put love on it! Happy😊.. Good luck all Fusionist
Since 2006 to 2012 ford fusion 3.0l rocked it.
Mr. Brotherly Review:
Nice video and review.....I know this vid is a year old but I am going to comment, Bought a 2010 Merc Milan Premier with 18 k in 2012 3.0. v-6 This vehicle along with the 88 Merc Grand Marquis LS are two of the best cars I have ever owned. 72 yrs old...
Took 2yrs for the airbag recall to be resolved on the Milan waiting for parts.Another recall was the led Milan tailights. Ford replaced under a recall. Bad LED connection insides the taillight assembly. thats it.
I am changing oil like clockwork,never more than 4k between changes. 5 w20 full synthetic. Valvoline. Trans service, airfilter etc. I do pull the throttle body and clean every 20 k. Vehicle has 86 k and runs and drives like new. I know 86 k is not a lot of miles but just an excellent car, 30 mpg hwy at 65 mph 23/24 mpg local driving
Yes I like Mercury Had a 2000 sable with 200k body started to go.. Figures Mercury is no longer so long
I have a 2010 Fusion SEL with over 174,000 miles on it and I must say, it's a pretty solid car!
First 6 mins a lot of helpful information at least for me 😁
Thanks bro.. 👌
You’re welcome 🙏🏾 glad I could help.
I'm picking up a 2010 Ford fusion today brother, I'm excited! Love the TL in the back btw!
Congrats on the new car! Hope it’s been maintained well 🤞🏾
@@BrotherlyReviews whoever had it took care of it for sure! Thanks brother!
Thank you for sharing, I have a 2012 Ford fusion and I brought it in2014 I have driven it daily and my Son was going to colledge and he drove it a year or two, I had to put a pulley a drive belt and the drive belt was in the last month ago the only downside of this car was the air conditioning, I haven't figured out what it is yet but I had a friend to bypass it and it will literally make you cut it all the way down because it will get that cold, I honestly can say I brought it in2014 and I still drive it daily no problems, a great car that has been good to me and my Family
I had to replace the idler pulley and belt also. The only issue I had with the a/c was the blower motor under the glovebox would occasionally have to be kicked for it to turn on. Had to replace a wire on it. Cheap and easy fix.
I used to have a 2011 Mercury Milan Premiere. I got the car in late June 2012. It had a little bit over 11,000 miles on it. I totaled the car by hitting a deer the 2nd time in early December 2016. It was a good car to drive in. It was the same as a Ford Fusion inside. I did wanted a Ford Fusion in 2012 that was a year old car. The dealership had about 5 of Fusions but, had almost 40,000 miles on them even a little bit higher price. I choose the Mercury Milan which had lower in mileage and even the price,too. It was my 1st car with Bluetooth and Satellite in it. Even the first with a keypad on the driver’s side door. I knew how to used a keypad on a Ford vehicle because my parents had it on their vehicles from Ford. When I first test drove the vehicle that I really liked the ride. My parents even liked driving the car,too. They did took turns in driving it. I got used to it by riding it. Right now that I’m driving a 2020 Ford Escape SE in black. It is my 2nd Ford Escape. I used to have a 2015 Ford Escape but, it died on me. Before the Milan that I used to drive a 2005 Ford Focus ZX5 with SES trim level. I had that car for almost 7 years till I was in a bad car accident in early March 2012. I broke my left ankle in that accident. My first car was a 1998 Ford Contour SE that I gotten in mid October 1999. I even gotten my driver’s license in that car in mid December 1999. I had the Contour to late May 2005. I’m into Ford vehicles since I was little. My mother used to drive a Ford Pinto which was the most dangerous vehicle from Ford. My mother was a very safe driver.
Great, well put together vid! I bought this vehicle for my son to be a reliable vehicle that he can add little mods to. Thanks for the info! 🤘😎
I have the 07 model 2.3 liter backed by the Mazda 5 speed automatic. Just normal maintenance, at 120,000 I replaced all brake pads and rotors front struts and rear shocks , right lower ball joints the left side was done at 102,000 , and rear hubs and the valve cover gasket and plugs , has 142,570 miles oh and because of winters I replaced the left rocker panel. I don't care what vehicle you own after a 100,000 miles it's normal to replace these mentioned above unless an individual does a lot of highway driving, I live in Michigan so the combination of bad roads and winters I'm very impressed with the reliability of these cars.
I have a 2012 Ford Fusion 2.5 I4 with 90K miles on it. Runs like a champ and I take care of it in every way I can. Still has almost all original parts and I've only put about 200 dollars into it so far.
I bought a 2012 ford fusion SE. Had 115 miles on it when i bought it In 2021 and recently lost it 😢 it got totaled. I miss it very much. It was a very good reliable car. Had no problems with it. Just got the brakes done, tires and obviously oil changes..
Our 2006 Chevy Cobalt just had a fatal heart attack (timing chain, for those who know😢). We are absolutely stuck with needing a new vehicle right now this second. Knowing these dire circumstances, would you still recommend a 2010 fusion? So far everything looks aces on reviews. Complaints appear rarely. People LOVE this year in particular. Thanks to anyone who can respond!
Yes!!! Go get that or the 2011....I have one
I swear that 2.5 I4 engine is up there with Toyota reliability, along with the Buick 3800 V6 engines. I'd definitely recommend any vehicles with these engines as daily drivers. Great review. I definitely want a 2.5 Fusion.
I agree. I’m a little over 220k in my 11’ SE 2.5, bought it new. Minimal issues that I can count on my hand. PCV valve, oil pressure switch, valve cover gasket and coolant outlet.
@@joel4210 what mileage did you have to replace those if you remember?
The 2.3 is just as good also 153 horse power duel overhead cam with the timing chain instead of the belt, very solid motor
What ab the 3.0 v6 2011 fusion se? Is it good & reliable??
@@joel4210 What ab the 3.0 v6 2011 fusion se? Is it good & reliable??
Had to replace the front driver side shaft and support bearing plus seal 🦭 left and right , and belt tensioner over the years but a great vehicle, I’ve had all the good ones in the past in the seventies, Mustangs , Chevelles , Dodge , Chrysler and this is the best car I have owned .
You cool and honest my dude. Keep on man.
Appreciate you King🤞🏾
When you go to change your spark plugs you will be very thankful you have the 4 cylinder. Changing the back row in the 6 is a chore.
Changing the spark plugs on my Acura TL was a pain in the ass, so I can imagine it’s the same for the v6 fusion lol
@@BrotherlyReviews Yep, same with a Lexus ES330. The intake plenum is bolted in the back to some brackets right up against the firewall...super hard & frustrating to get to. I think the engineers design things like this on purpose so owners don't work on their own cars. They want you to bring them to the dealer service dept.
@stevemccooleq I’ve always thought the same thing lol it’s a money scheme
I have a 2012 eel fusion 2.5, so reliable
I got it at 17 and at 21 I put 30k miles on it easily and only had to do the brakes, valve cover gasket as well as the whole front suspension with cv axles but the suspension was still solid for the most part.
Amazing vehicle for a daily if the transmission and engine goes I’ll most likely just throw in a new drivetrain
Thanks for your candid review. My daughter is looking to purchase one, and it was super helpful with what to expect.
You’re very welcome! Feel free to reach out anytime if you have any questions 🙂
I have a 2012 SEL, and it does me just fine. The thing will go when needed, no issues passing someone or merging. For a 4 cylinder its above expectations and the gas mileage is fantastic. I can make $120 door dashing and spend $20 in gas 😂
I have a 2012 with the 3.0. It runs great.
Same color as mine. My advancetrac is bad and paint is peeling. Other than that it's solid. Good sound system too
I like your vid. I have a 2017 se 2.5 l. In the mornings after the engine warms up, I drive down the street, stop, make a turn, and after the first shift it feels like it slips but after that it works fine. The fusion 2.5 is the most solid car wish it was faster like you said but it’s a sacrifice between reliability and power.
The most common problems for these cars are fuel pump issues, because there built into the the camshaft (genius idea right?). Anyways, that slipping could range from transmission all the way down to a faulty spark plug.
Same thing my 2011 used to do, but after it warmed up, it didn’t slip
@PLUG! 🔌 what? Lmao the fuel pump is not even near the camshaft!🤣
I have a Mercury Milan hybrid. So far it's the most reliable car I've ever owned. Over 122k miles.
Hey man! Nice review!! I really like that body style of car. It’s very good looking.
Today, I picked up a 2012 Lincoln MKZ! Pretty kick ass comfortable luxury car.
I sold my bright red BMW X4 M sport for it, it was just too expensive for me. I had it for over a year, and I always had to live so financially tight, that I couldn’t have any spending money.
I got sick of that, so I picked up the Lincoln, for a great price. It’s a really good car.
I plan to keep it for a long time.
I wanted to ask you, you said you had the 2 L engine, which has been very reliable, I’m glad to hear that. Is the 3.5 L V6 engine reliable? That’s what I’ve got.
Thanks!
Same car. Only mine Is SEL. No spoiler had the entry / lock keypad. Same style Same light display. Different rims. After 8 years. Having to replace the tranny lines to radiator. But these ford's MOVE. Over 90 they become loose. Mines dual exhaust and double catalytic converter. But man. Same body and all. My miles are way less for a 2011. Like 85000. Mines fully loaded. But you got a good ride. As soon as I fix mine up. Prolly trading it in.
Good honest man!
Appreciate you 🤞🏾
I have a 2007 Gen1 Fusion SEL in the same color Amethist metallic. I Love it
Thank you for this I’m looking at this blue 2010 one..
Look for the 2011 if you can.
2011 and 2012 had some differences with the steering wheel controls, and none of the 2010 models have automatic headlights.
That’s IF it’s something you care about
Other than that, 2010 is still a great option
My aunt is fixing hers up and giving it to me. This will be my 1st car so I’m trying to do my research
Great first car choice!
Feel free to reach out with any questions/needed advice 🙏🏾
Wow... looking good for it's mileage!
most definitely
Excellent, thanks
Awesome video man, I am actually looking into buying this car right now! Can you tell me the details for the Apple Carplay unit you're using to get all those features? I think in the video you said Maestro RR, just want to confirm
I don’t remember the exact one I had, but it’s a pioneer head unit. All of the NEX models have CarPlay and android auto.
I’m looking at a 2011 Fusion SE , the car has 179.000+ miles on it
The car does have a little Rust towards the rear of the vehicle but not bad , it’s either the Fusion or a 2012 Focus SEL with 117.200 miles which is in better condition than the fusion I’m looking at, both cars are being sold for super cheap I’m undecided about which car I’ll buy, I don’t drive around much I do that at work (Amazon Delivery) lol I’ll only be using the car for transportation from home to work.
I have a question.. i just recently bought this exact car and I had a 2017 nissan altima with a back up cam, and i was wondering where did you get your screen/carplay? Thanks for the vid!!
The brand is called Pioneer NEX. Ordered from eBay if I remember correctly. There’s a ton of different ones. Just make sure it’s an NEX model if you want Apple CarPlay/android auto
PCV Valve need to be replaced but is located behind the intake that has to be removed and as I understand should be replaced every 30 thousand miles Don’t you just love it
Does the car usually give a engine code for that? The check engine light never popped up on this car for the two years I had it.
I own a 2007 ford fusion with 3.0 it has 270,000 on it.. an it burns a little oil but still runs good
The 2011 sport certainly isn’t reliable, but I still love it 😅
What issues are you having? I only know they’re notorious for engine failure if you don’t replace the water pump on time, but that’s about it. Most engines will do that.
i had a 2010 fusion hybrid i loved that car but dumb me i gave it to a family member that needed a car and now i wish i would have keep the car never and any problems with it and it had 150,000 miles when i bought it and it had 201,000 miles when i gave it to a family member and the car was still running great
I bought a 11 fusion. Has 191k on it right now. Backing up has some clicking but worse on sharp turns and does it at first forward moving and goes away. Rides awesome and reliable. CV axles maybe?
That’s a possibility
Control arm bushings
Yes you need CV axles however if you don't have anything modified the likelihood that they actually break or leave you stranded are low
Great video bro !!!!!
Cool video...have 2011 been very dependable
Great video buddy. My ford escape hit 605k and I'm on the hunt for the fusion with the stick. 2.3, 3.0 it even 3.5, I will find it.
This helps going to go buy one for 3800 with 202k miles
I have a 2012 ford fusion SEL AWD with 119k have had it for 8 months and love it just put magnum flows on it and getting ready to put an intake on it trying to improve the gas mileage only get 20 mpg on the highway
20 on the highway??? Jeez! The V6 is supposed to get like 27ish on the highway. Have you done any maintenance to the engine?
Just basic maintenance but since I’ve do the exhaust it’s up to 27-30
@@BrotherlyReviews the awd is 18 city 20 highway not the best but I love it
Maybe the stock exhaust had a clogged muffler/catalytic converter or something
Sharpe vehicle that has stood the test of time.
Sure has!
Wouldn’t mind buying another one in the future 🤞🏾
Like that you got the newer factory 2012 wheels on yours makes it look like a genuine 2012 model now compared to the cheap bolt on covers the 2010 and 2011s had on the SEs
I hated those with a passion. Kept losing them on the highway 😂
@@BrotherlyReviews I own a 2010 Sport in silver with the bolstered leather interior with the blue racing inserts. Was my Dads brand new originally. Ours has never seen a winter and is always stored. Has low miles 23k and is very fast with that Aisin T80 6spd and 3.5 DOHC 24V Cyclone High Output V6. Love these cars
@@BrotherlyReviews yours is very nice and you're correct the Mazda 2.5 Inline 4 is super reliable engine they also used that in the Escapes and Rangers of that same era. In which we had a 2007 Ranger base never any issues
I have a 2012 se with 17 inch alloys but it has no spoiler. why would his 2011 se have one and not mine?
@@evanlovestdwp his might have that as an dealer negotiation added accessory. Weird cause the SE is a mid trim level and they all mostly came with that standard. Then again I see some SELs that also didn't so depends how it was ordered. Only model that came with everything was the SPORT and that trim was its own trim!, yet I see some SPORTs that dont have moonroofs and seem just as stripped down as a base SE with exception of the High Output powertrain all SPORT models come with as standard equipment
For the hybrid 2.5 vs se and these are 2 different engines the hybrid utilizes a Atkinson cycle 2.5 while the se utilizes the Otto cycle
Just bought my son 2012 sel 3.0 with 178k runs and shifts great hoping it last him awhile
Congratulations 🎉 great purchase! That’s what I’ll be looking for whenever I’m in the market for another Fusion. Or the Sport.
@@BrotherlyReviewsI got a 2011 3.0 for my Turo fleet. I stayed away from the 3.5 due to the design where the water pump is internal. I don't want maintenance being that difficult for a part that should be semi easy to change out should it go bad. With the internal water pump you're just asking for trouble.
Great solid american work horse of a daily driver !
Agreed 🙏🏾
Thank you!
Seeing yours having 220k miles gives me hope because mine is at 80k miles. What part of FL are you in? I want to move out of Philly to FL.
I’m in Orlando/Kissimmee area
@@BrotherlyReviews Got it, I'm debating between Miami/Lauderdale and Tampa.
Miami is very expensive to live. I’d recommend Tampa.
Great video. Thoughts on a 2012 for $9,000 with 104,000 miles? Looking for my first car. Thanks.
Sorry for my late reply. Are you still interested in getting it?
@@BrotherlyReviews found a much better deal. Bought a 2010 with 62K mikes for 6K. The car is in great condition. Going to get it detailed over the weekend.
Awesome!! Congratulations 🎈🎉
@@elijahs7280 did you pay cash? I found one for 70k for $6900 but I want to see if they are willing to negotiate.
huh. toyota fan but maybe picking up a family owned fusion 2010 SE in great shape, from California, with 46K miles. N0t sure of price yet but kBB around 6-7000 private party value. But concerned about transmission/steering problems among other things..it being a Ford. but maybe might be good for the kid for the next 4 years of college.
I have a Fusion 2012 3.0 V6. I just upgraded my turn signals to syneticusa. I am looking forward to replacing high beams with H7 LEDs but I don't know if the dust caps would fit back on with LED lights. Could you share which high beam you use and whether you had trouble with putting dustcaps on afterwards?
I have the same turn signal leds in mine also. I did replace my high beams with H7 also, but I couldn’t use the dust caps afterwards.
Mine has daytime running lights, so I can’t use hids in mine. But even when I did have them in just to test, they were actually worse than LED.
Hey brother where did you get that radio and where did you get it put in? That's an awesome look and exactly what im looking for
Ordered it from Speedzone Performance , and had it installed at a shop named 12 Volt USA
@@BrotherlyReviews I appreciate this man... and here I was gonna trade for something newer
Just bought one for a daily, sat for 3 years under a tree. Jumped it and it drove home.
I bought my 2010 SEL 2.5L with 66k miles a year ago and I love it way better than the malibu I used to have. Are those the stock fog lights or did you buy them?
Fog lights come standard. I replaced the bulbs with leds. Same for the headlight bulbs also.
Looks like you live in FL, I live in SW Fl. Love my 12 ...........low miles , good car , Oh yep FL plates lol
lol yup I’m in Orlando
I have a 2012 Fusion Sport, I finally found a car to replace my 1995 Tauras SHO, the SHO is faster but the Sport is quicker I still have the SHO
What a great combination! Congrats 🎊
0:38
3rd light is out!
I wasn’t pressing the brake lol
@@BrotherlyReviews oh lol
Can you tell us the model name of the pioneer infotainment system you installed..?
thanks appreciated
Dmh 1500 NEX
I used mine for uber. A 2011 with the v6 and no cap bro, i put that same underglow under the seats!! Lol 😂
Definitely sets the mood lol and only $30
Can you share the link for the head unit that you changed to get apple car play - im considering buying one of this and apple car play is a must for me - if you could share the link, pricing and installation details, woulds be really helpful
Don’t remember exactly which one it was, but as long as it’s a Pioneer NEX it’ll have CarPlay and android auto
I just bought a 2012 with 58k miles
Where did you get the underglow lights? they look really nice on the interior, the 2017 Ford Focus SEL came with an integrated underglow interior lighting system which i really miss tbh makes the car look nice at night, where did you get the ones the fusion have?
Amazon brother
@@BrotherlyReviews are they easy to install? Ive heard missed reviews especially in regards to the adhesive alot of people say to get aftermarket adhesive cuz the ones that come with them suck and they be Fallin off lol
The ones I have use 3m tape on each of them. I’ve had them for about a year now and haven’t had any issues with them. I’ve even moved them around a couple times and they still stick.
I’m looking at 2011 Ford Fusion 2.5 just wondering if it is a good car to buy.
It’s a great car to buy if you want something affordable, reliable, and comfortable 🤞🏾
My town car weighs 4300 pounds and has a 4.6 tops out at 104 mph with 280 hp and that fusion will smoke my car man I'm thinking about fusion or a Sonata
Rather have the town car , those cars will go 500,000 miles
Im looking at the same one only 2012 with 44k miles and I’m deciding wether I get it or not
Do it!!!! I’m seriously considering buying another one in the future
Do you have problems with harsh shifting when stepping on it when its alteady moving ? Or when slowing down
Nope. Used to slip between 3-4 gear during the first 2-3 mins of driving, but once it warmed up, no shifting issues at all.
I want to purchase this 2010 Fusion Ford SE card with 198K miles, its $3200. Is it worth it? It's had only 1 owner and he claims hes kept up with maintenance, im just nervous.
Sorry for my delayed response
Do you know what engine it has? 4 or 6 cylinder? If it has the 4 cylinder then that’s the best engine for reliability. I would definitely get the maintenance records before you purchase, to make sure .
Did the LED lights come for the car or did you add it? I have Led in mine too but mine is inactive
I installed them. Didn’t come with any leds from factory.
Anything wrong with the 2014 2.0 Ecoboost?
Turbo failure, coolant leaks into the block, better off with the non-ecoboost engines
I have a 2010 se it’s at 170k with the same motor
How reliable the car is what would you rate it out of 10? I'm going to test drive one today 2010 SEL but I'm not sure what to expect out of it
10/10 for sure! I’ll definitely be buying another one in the near future.
@@BrotherlyReviews I have a 2012 Ford Fusion SE 185k miles on it, how long you think it will last me? Maybe 230k miles??
I sold mine, but I know the owners currently has 232k still going strong 💪🏾
I have 2011 i have 267000 miles on mine
Is it still going
What about the 3.0 v6?
It’s a good engine, but I’ve seen people have some issues with them. Nothing major though.
What is ur tint setup? All around
Windshield 35%
Front windows 15
Back windows 5
@@BrotherlyReviews Thanks
Should of bought the V6 version a 3.0 or 3.5 w/ the leather interior
At the time, I was specifically looking for a 4cyl because I wanted something fuel efficient
@@BrotherlyReviews good purchase you don’t need the v6 or leather.
I have the TL that offers all of the above. For a daily that wasn’t necessary lol the cloth seats were extremely comfortable and easy to clean
What type of backup camera is that and the radio I want that setup
Pioneer NEX. Don’t remember what brand the camera was.
Agreed. I’d love this setup for my Fusion as well.
I think the 2010 - 2012 fusion is worst used car you can buy because of the eletric power steering issues. I think it's like rolling the dice with one of these cars...
Can’t say I can relate 🤷🏾♂️ been the very least problematic car out of the 16 I’ve owned so far. The power steering issue was a recall though.
Where did u get the spoiler? got a 12 n same color as urs.
Junkyard from a Sport, then took it to get painted
Just got the 2012 2.5 with 106k will carry it to 200,000...
Easily! These cars are solid!
@@BrotherlyReviews had the 08 2.3 fusion love it so I jump to the 2012 from there I think that's the final best of the fusion........fallow up for me.....
I’m yet to see/know anybody with a 1 and 1.5 Gen 4cyl fusion that has ANY issues with it.
Even the hybrid for the 1.5 Gen nobody has issues with
@@BrotherlyReviews future common issue is battery pole connect valve cover gasket....maybe alternator or water pump....change thermostat now and your safe....drill a 1/4 inch hole on thermostat before in stall to safely take out air bubble or air packet.... That about it... Change all oil to time...
23,000 in 2 years I put 23,000 in 6 months lol
Lol yeah I don’t drive much 😅
okay but hows the 2015 model with the 2.5L engine? are they good and reliable?
Yes it’s the same engine from 2010. That’s actually the most reliable engine in the whole lineup of the fusion. The ecoboost engines are garbage.
@@BrotherlyReviews apart from the engine, how's the car overall? Would u recommend buying the 2015 model?
The 2015 models definitely have some extra tech, so I definitely would recommend. Especially with the 2.5 engine.
@@BrotherlyReviews I saw few ppl comments on different vids talking about some transmission issues with the Fusion, what do u think about this?
The 6F35 is a transmission known for failure, but a lot of it also has to do with maintenance. Mine would occasionally slip between either 3-4 or 4-5 gears when I first start driving it, but once the trans fluid reaches operating temperature, it doesn’t do it.
@ anyone knows how to connect phone to 2010 fusion ?
Not all of them have Bluetooth capabilities
so no transmission or steering problems like a lot of post talk about
The trans in the 2.5l and 3.0 are known to give issues, but like most cars it’s due to lack of proper maintenance. Mine had 225k when I sold it and no issues with the trans. I always drained and filled the fluid once a year.
Is that the original paint??
No it isn’t.