So greatly explained Thank you But one question What tyoe of car scanner should we use for the scanner OBD 2 I need adapters to fit 1999 toyota Hiace turbo diesel 3 lt automatic 4 wd
Hi Peter.love your videos.so helpfully. I have a 1994 Corolla. The idle used to be really good. Now it has started to idle slightly higher. It does it mostly when first started but seems to get better when warm. No codes.no vacuum leaks.have cleaned throttle body a bit but not helped. Car gets up to normal temp quite quickly. New plugs and air filter. Any ideas or suggestions please? Thanks.pete.
Amazing video, will plan on checking on my 1998 corolla. I have an issue with high idle (1200 RPM with AC on & 1500 RPM with AC off) - also have an issue with the AC compressor, it keeps engaging & disengaging when car is at idle, unless I rev up to around 1700 RPM, at which point it functions normally - and also functions nornally when I am driving.
Hi. I have a question to ask u. I have a Toyota Corolla 1999 and I can't pass the Emissions. There is a new cat and Lamba sensor gone into it. Emissions are still high. The car has been off the Road about 3 years we did start it from time to time and let it tick away with out moving. Would u have eny idea of my problem. Thank u.
Hi peter i have a 5a fe ae110 i tried to read and delete abs codes but te lights dont blink and show the stored codes and also don't delete i found a broke wheel sensor i replaced but still my abs dont work maybe i have to use a scan tool?
I did as you mentioned in the video. Unfortunately check engine diode blinking all the time the same speed without any pauses. I can't read any code from this. Can you please advise what is going on ?
Hi bro. Thank for you explained that. In my case I a have an toyota Tercel 1995. But when conect the wire in TE1 an E1, nothing happens. Just the engine stays one. I would appreciate if tell what I could be doing wrong. 7:46
How to you fix Code 13? i have a Corolla 1995 GLI .. Do I have a bad camshaft sensor? or is my Cam Shaft Timing incorrect.. right now its set to 0 degrees? thank you for helping.
@@PeterFinnTheCarDoctor finally i found the problem is about the ECu capacitor burned.the partis somewhere control a/c and ignition timing which 3k rpm above.
Hello Peter,Why is it may car everytime I scanned it with obd,the abs flashes and then it says Link Error.Even I used different obd scanner the result still the same.Thanks in advance
My 2000 Corolla is also having the issue that some people are asking but there is no answer to it? Check Engine Light is ON but jumping E1 and TE1 the CEL just stays on, no blinking whatsoever... Has anyone figured out what it is?
HI Peter can you help me with a error code. I have a 7afe lean burn engine in my corolla. the error code is 36. Can you please help me understand this code and how to clear it. thank you.
Peter Finn . Thank you for your reply but car does not have abs as its a swap engine. Here in Pakistan we dis not had ABS in ae100 model. A little research showed something about combustion pressure sensor but how to check and clear it.
HELLO , I CONNECT TE1 AND E1 , BUT THE ENGINE LIGHT FLASHES ON AND OFF CONTENTIOUSLY THERE IS NO 21 21 CODE MY CAR WORKS FINE BUT WHEN I ACCELERATE THE SERVICE LAMB LIGHTS FOR A SHORT TIME THANKS , AND SORRY FOR MY BAD LANGUAGE
Hi, I offer you paid help related to the video car repair event. Please pay me 5 USD via the THANKS button below the video. Make the payment and I will then give you a professional answer to your question.
Oh, thank you very much Sir Peter. I've tried googling the location of intake air temperature signal but I cannot find it. Do you have any idea where is the location of intake air temp signal in my toyota corolla GLI 1993? Thank you very much Sir peter.
Friend I do all your steps but when I open the switch in mode on the motor light is fixed and does not flash like your car in the video, help me .. I did everything right connect e1 with te1 then insert the key and put it on mode wait Up to 10 minutes but no flashing friend give me a solution I would appreciate it
IRAQ GIS TEAM that indicates that it has some problems. My 2 cents would be not to try and fix it as long as u can drive. Try to read the codes as shown above and see what it is. There was somekind of a reset as well aka 15min no battery but first read the code. And dont try to fix it if is immo related otherwise she might not be a runner no more. All the best!
Amazing breakdown and explanation - and all done in a second language of english! Go the Finn!!
👍
brooo, i never knew old diagnostics were this cool 😂
👍😃
So greatly explained
Thank you
But one question
What tyoe of car scanner should we use for the scanner OBD 2 I need adapters to fit 1999 toyota Hiace turbo diesel 3 lt automatic
4 wd
Noted 👍
Did that and came back to say thank you.
👍🤠
your channel is heaven sent. Learning alot! kudos
You are so welcome and Good comment. Thanks 👍😀
Thanks so much, got my codes so easy.
Great to hear!
Hi Peter.love your videos.so helpfully. I have a 1994 Corolla. The idle used to be really good. Now it has started to idle slightly higher. It does it mostly when first started but seems to get better when warm. No codes.no vacuum leaks.have cleaned throttle body a bit but not helped. Car gets up to normal temp quite quickly. New plugs and air filter. Any ideas or suggestions please? Thanks.pete.
Throttle body is bad
@@PeterFinnTheCarDoctor in what way Peter?
Peter whats code 33 in s toyota corrolla
Hello Peter. Have the same issue on a 94 Corolla. Used to idle at 800, now it's around 1000. Did you ever get to sort out the issue? Thanks
Check if the idle control screw did not move the throttle butterfly a little. It's on the throttle bottle by that accelerator.
Fantastic explanation truly the best and easiest to do. Thanks
Amazing video, will plan on checking on my 1998 corolla.
I have an issue with high idle (1200 RPM with AC on & 1500 RPM with AC off) - also have an issue with the AC compressor, it keeps engaging & disengaging when car is at idle, unless I rev up to around 1700 RPM, at which point it functions normally - and also functions nornally when I am driving.
Good luck!
Hi. I have a question to ask u.
I have a Toyota Corolla 1999 and I can't pass the Emissions.
There is a new cat and Lamba sensor gone into it. Emissions are still high.
The car has been off the Road about 3 years we did start it from time to time and let it tick away with out moving.
Would u have eny idea of my problem.
Thank u.
Hello.
I think you need new piston rings. 👍
Your video was very helpful bro. Looking forward for some issues which you resolve thank you.😁😁😁
Hi Peter,awesome video.I got code 33 in my avensis 1999 4A-FE.Any idea what is it?
Thanks for info 👍😀
Thank you, very helpful!
Glad to hear that!
Hey sir peter I got a code 12 with my 93 Corolla 4afe engine what it means?
noted
RPM signal Distributor circuit or crankshaft position sensor
Very helpful video, thank you very much
You are welcome!
Hi peter i have a 5a fe ae110 i tried to read and delete abs codes but te lights dont blink and show the stored codes and also don't delete i found a broke wheel sensor i replaced but still my abs dont work maybe i have to use a scan tool?
Thanks for comment 👍
Wonderful as per usual
Thank you! Cheers!
bro you are absolutely amazing! thank you for very much!
Beautiful, absolutely! Thank you.
Thanks
Sebe hade stor nytttttaaaaa💪
You're welcome!
This guy is my hero lol.
Hey sir why my blink fast
I have a toyota corolla 95 wagon can u help me
👍😀
I did as you mentioned in the video. Unfortunately check engine diode blinking all the time the same speed without any pauses. I can't read any code from this. Can you please advise what is going on ?
Means no issues, no codes, healthy engine
@@heartwarrior640 thank you very much, I did not expect that as the car is 23yo, well it's Toyota
how about the continous flash of the check engine light?
Noted 👍
Hi, what is the warning sign b4 u do the diagnosis?
Thanks for comment. I appreciate 👍😃
Do we really need to reset? What happens if we dont reset?
thanks. now I know ho to read motor fault blinking.
Thanks for comment. :-)
Is that obd1 or obd2 port?
1
Hi bro. Thank for you explained that. In my case I a have an toyota Tercel 1995. But when conect the wire in TE1 an E1, nothing happens. Just the engine stays one. I would appreciate if tell what I could be doing wrong. 7:46
I have read your message, Thank you 😀👍
@@PeterFinnTheCarDoctor That is the best answer you could give?
How to you fix Code 13? i have a Corolla 1995 GLI .. Do I have a bad camshaft sensor? or is my Cam Shaft Timing incorrect.. right now its set to 0 degrees? thank you for helping.
13: Intermittent loss of RPM signal - Probable cause is a bad distributor or the connection to the ECM.
Hi peter, whats the problem if check engine light is not showing even the key is set in turn on?
Hi, you don't have issue now
replace the starter motor relay
super Peter ...
Thanks Sir !
Hi Peter, my corolla '93 only give codes when i start the engine.. if the engine is not running it won't give codes..
Thanks for comment 👍
Hi, brother. If mine car with the check engine line no trip cannot count. Any suggest
Let me check... maybe new dashbord
@@PeterFinnTheCarDoctor finally i found the problem is about the ECu capacitor burned.the partis somewhere control a/c and ignition timing which 3k rpm above.
Hi. Whats the error for code 24 and 42?
24 intake air temperature,or sensor circuit 42 vehicle speed sensor or sensor circuit
Sorry sir
Where can i find this code ?
Can you tell me link 🙏
Noted 👍
what is red (!) ?? in corolla 95'
nice vedio ...... you great
Thank You too and You are welcome. :-)
Dear Mr...when I connect E1 and TE1 there is not binking check engine light.is light up continuously....whats wrong.pls help me.🙏
Hi, please try again...this is difficult test
Could mean you don't have codes
Mr Peter please help me my Toyota corolla 1.6 1992 model executive 4af carbarator I need to replace a speedometer cable
Noted 👍😊
What if the engine light flashes contently if you do the diagnostic?
Thanks for comment
it mean no codes stored
Hello Peter,Why is it may car everytime I scanned it with obd,the abs flashes and then it says Link Error.Even I used different obd scanner the result still the same.Thanks in advance
Ok, I think that You have some error in your ABS cables?
Peter Finn Thank you peter I'll check it.
I have a Toyota levin 97 code 33 any idea what it means can not find it anywhere ?
may be 32 air flow sensor
Hi dear I have Toyota camry 2002 I have 3 codes 62_ 63_ 64 what mean? ?? And car not start
Good comment 👍😀
My 2000 Corolla is also having the issue that some people are asking but there is no answer to it? Check Engine Light is ON but jumping E1 and TE1 the CEL just stays on, no blinking whatsoever... Has anyone figured out what it is?
Hi, please use OBD scanner
I did the connection but my check engine light dose not flash, it stays on plz help
HI Peter can you help me with a error code. I have a 7afe lean burn engine in my corolla. the error code is 36. Can you please help me understand this code and how to clear it. thank you.
Hi, You have issues in ABS system sensors. Left or right front speed sensor.
Peter Finn . Thank you for your reply but car does not have abs as its a swap engine. Here in Pakistan we dis not had ABS in ae100 model. A little research showed something about combustion pressure sensor but how to check and clear it.
HELLO , I CONNECT TE1 AND E1 , BUT THE ENGINE LIGHT FLASHES ON AND OFF CONTENTIOUSLY
THERE IS NO 21 21 CODE
MY CAR WORKS FINE BUT WHEN I ACCELERATE THE SERVICE LAMB LIGHTS FOR A SHORT TIME
THANKS , AND SORRY FOR MY BAD LANGUAGE
Hi IRAQ GIS TEAM I HAVE THE SAME PROBLEM....
Did you find the solution???
Hi peter I was searching for this kind of video.unfortunately the code I Observed in my corolla 97 was not accurate as what you have in the video.
Hi and many Thanks for comment. :-)
Peter Finn pls Peter help me find this out.. Here is the link check it out. ruclips.net/video/PLpjLiVh7ho/видео.html
Engine check light is blinking very fast no gape i can't read. Plz help
Thank You 😀👍
@@PeterFinnTheCarDoctor my car check engin check light is blinking very fast i m not able to read the code, why it is blinking so fast?
Nice
Very nice
1996-later is upgrading to OBD-2.
From 2000
Not correct. My 1999 Camry has OBD 2
@@PeterFinnTheCarDoctor lol you should check your facts
Hi I tried it but my engine light flashes none stop why is that
Thanks for info 👍
How to delete the check light in this car
Hi, I offer you paid help related to the video car repair event.
Please pay me 5 USD via the THANKS button below the video.
Make the payment and I will then give you a professional answer to your question.
No thks. I already found the way.
Working on a 2007 mustang GT 4.6 engine won't start
Thanks for comment 👍😀 Good luck
Thank you very much for this video.
Unfortunately, mine was code 13 & 24.
Wonder how to fix this.
Hi, I need to do new video.Code 13 Rpm signal to ecu missing above 1000 rpm and 24 Intake air temperature signal fault
Oh, thank you very much Sir Peter.
I've tried googling the location of intake air temperature signal but I cannot find it.
Do you have any idea where is the location of intake air temp signal in my toyota corolla GLI 1993?
Thank you very much Sir peter.
@@PeterFinnTheCarDoctor how to fix it?
Friend I do all your steps but when I open the switch in mode on the motor light is fixed and does not flash like your car in the video, help me .. I did everything right connect e1 with te1 then insert the key and put it on mode wait Up to 10 minutes but no flashing friend give me a solution I would appreciate it
Intresting.... I will investigate
I have same problem
@@PeterFinnTheCarDoctor my check engine is not blinking after I connected te1 and e1 plz reply
@@ahmedserag2607 Did you ever figure out what was the issue?
What is tha code
Hi, and Thanks for comment. 👍😀
code 32 ? please
Hey when I do this in my 94 corolla the check engine light just keeps flashing
Yes, this is the idea
that means that ther is no faults
@@sakalamaka I have the same issue , but my corolla 1995 service engine comes on immediately after moving for seconds
isn't it a problem
IRAQ GIS TEAM that indicates that it has some problems. My 2 cents would be not to try and fix it as long as u can drive. Try to read the codes as shown above and see what it is. There was somekind of a reset as well aka 15min no battery but first read the code. And dont try to fix it if is immo related otherwise she might not be a runner no more. All the best!
Most probably lambda
how i can read 3digit codes like 301?
Hi, I tried to do new video to You. :-)
Peter Finn where I will get that video
Well, today I am in my garage, an d I try to do video. Let's see, maybe in next week ?
thanks Peter finn
can I connect u via fb
code 32 ? corolla liftback 1998 please
Noted 😀👍
Hi sir my code is 52?
Noted 👍
Is it possible to link the site, it is from the Arabs, I follow you, please
Good Comment 👍👍👍
1991 toyota corolla code17
Good Work ! 😀👍
search link please
Thank You for Your comment. :-)
My check light blinking
Ok
goog
good
Won't start
Thanks for comment 👍😀
1991 toyota corolla code17 help anybody ? peter
Thank You for comment. 👍😀
Code 27
Oxigen sensor circuit
Car stager
Noted
Mormones, no me interesa su información.
Thanks and noted 👍
You take too long too diagnose one issue
Thanks Sir. :-)