I did the same with my 2.4l toyota 2 years ago. Problem fixed. All pro techs said that VVTi had to be replaced (only several grand with labor) lol! Don't forget to properly reset the new tensioner by slightly rotating the crankshaft in the opposite direction. It will open the little hook on the tensioner and allow it to extend and self adjust.
Thank you for this video,my 2005 corolla started making the rattling noise , now I know the problem. Mine the noise is there constant even when I have driven the car for long, the noise doesn't go away.
My f*%#ing hero I'm having this same problem in my 09 Matrix. The TSB on this advised replacing the whole timing system - an actual nightmare. Thanks a lot!
Nice work. You can also release the hook from the tensioner with a screwdriver since you had the valve cover off, which is not required to replace tensioner, but the factory service manual recommends it just to be 100% sure hook is released. I have the same engine with 226,000 miles. You can also rotate opposite direction like 15-20 deg which will tension the slack side of timing chain and press on tensioner, releasing hook. Then turn clockwise.
That's what everyone always asks me. It has just got 100k last week. I work about 15 mins from home. I've driven it up the So Cal coast a few times but mostly to and from work. It's been great to me.
So you didn't replace the chain with a new one? And the tensioner magically got the slack out of the chain between the two gears? So that means there is no noise when a chain overlaps gear teeth to get tighter from the tensioner? That would be great if that was the case!
I just got my mom a 2009 scion xb and it's making crazy noise and it's has great power! But that noise! She gone love it! I was gone change the whole engine thank you so much!
Buenas tardes vi sus vídeos y tengo una pregunta tengo una Toyota venza 4 cilindro y me ace lo mismo.dónde está ubicado el tensor de la cadena de tiempo?
Hi Nestor. I replaced the timing chain tensioner and followed these instructions but I was told later that after installation and spinning the crank clockwise, you’re also supposed to spin it counter clockwise. I did not do this and heard a loud rattle at first start up but it went away. Is it necessary to spin the crank clockwise and then the other way for proper tension?
Guessing you've already done this repair buddy but yes the Toyota manual specifically says to turn the crank anti clockwise until the hook on the tensioner unlocks. This should only take a very small amount of rotation and you'll hear the click. Then crank clockwise to extend the tensioner, you'll hear a series of clicks.
Even a brand new one will move by hand. It's supposed to. The only time that the tension increases is when it is installed and the oil going into the tensioner increases the pressure/ tension on the chain.
Hey, do you think a long drive where the oil is burned below the stick would cause the rattle to start? My 09rav4 is rattling a bit now after a 5k drive. Oil is below the stick so the oil needs a change. Hope it fixes the sound at the same time.
Nestor, thanks for the video. My 2002 Rav4 2.0 liter is rattling and I suspect it's the chain but haven't looked to check the tension yet. It starts rattling about 30 seconds after cold engine starts running. i will check under valve cover tomorrow. Do you have any advice on that particular engine and part replacement if that is for sure the problem? Thanks again.
Hello thanks for the video. My toyota wish has a rattle when idling and low speeds which leaves on acceleration, could this be the issue as well? Thanks
That chain looks really loose, so I’d imagine it’s got a constant rattle right? My rattles for a split second on start up. Do you think it would be worth me bothering with it at the moment or just keep a ear out to see if it gets worse then fix it? Like I said, it’s only on start for about a second then no rattle and smooth operation. I have the 2013 Toyota Corolla.
I think you should replace the tensioner ASAP. If it keeps getting looser you’re gonna have metal on metal and pieces of the sprocket are going to break off and end up in your oil. Then you have to replace the sprockets too and that’s an all day job maybe even two for some people! $$$
Hi, I have now a short loud rattle after cold start. But if I turn it off and on again, there is no short rattle anymore. Do you think it's the tensioner or the VVTi-camshaft making this noise?
Ben, did you find a fix to your issue?? Please help me if you did. I think I have a similar issue. It comes and goes. Even if I restart the engine. Strange. I checked my vvti solenoid and cleaned it. Works perfectly when checking with electric current
Good job bro, I have a 05 vibe pretty much as a matrix same engine . So when I start it's making the rattle sound like it's coming from pulleys I change power steering pump and new altenator and it makes same sound , so I guessing it's the timing chain is loose.
My car doing the same thing Toyota Venza 4 cylinder . I've checked everything under the hood and change heat shield, still have a loud rattling when first cranking up and when give it the gas
Does that noise happened in the cold weather or it happens all the time. I have similar noise on my 2009 Corolla but not sure it is starter or chain. The noise sound like, when car starting and I try t start again like starter gear hit flywheel gear but not 100% sure. So far, It seems like only happen in cold or car stayed over night. After car warm up, no more start up noise. Thanks for the video. Thanks in advance.👍
Questions for Nestor Auto Repair... Why did you use a socket and wrench to manually turn the engine to get the tensioner to release? Why didn't you just turn the engine using the ignition switch?
I've replaced the timing chain tensioner and the intake VVT gear and yet still the the VVT rattle on cold starts. The top chain guide showed no wear. Why? I change my oil every 4K and owned the car at 20K miles. It now has 92K miles. No check engine light for the VVT solenoid.
Wassup Nestor I have a 2010 Camry 4 cly and I have the rattles upon cold start it’s sucks! What’s the difference between the vvt cam gear rattle and the timing chain tensioner rattle? Also if it would be the tensioner would I need to adjust the timing or double check the at any point?
Hello well for the vvt your will get a code and also the rattle will never go away ,, if there is no code for timing you don't need to adjust it just add the new tensoner
Hearing an occasional rattle at idle.....not sure if it's a water pump going bad or this tensioner....it's on the same end of zthe engine as the belt drives. Scion xA first gen. Is there an easy way to tell which it is?
So my 2003 corrola had that rattling and then one day it just didnt turn on.. i took out the valve cover and it has that same slack on the chain, should i try replacing tensioner first or should i just replace the chain and all?
Well if the car still crank it need a new chain because you want too long and the chain stretch and jump timing , but if is not cranking then it may be way too late engine lock up. Hope not
@@nestorautorepair okay thanks, yes it cranks and sounds like it wants to start, i havnt checked the timing yet, im just going to do the whole timing chain job.
Sir i have 2007 toyota with 1zzfe engine . When is stop car or in neutral then i heard a noise like a diesel engine plz refer me that's the noise of tensioner also ?
Is this the fix for the chain rattle you can hear clearly when the engine is idling? I have that weird chain noise that sounds like something is loose inside the engine in a 2011 Rav4
My toyota corolla 2009 having rattling noise on cold start for 10-15seconds, Mechanic told me to change complete timing chain... So should I change Complete chain system.... or just Timing tensioner ? Please help 🆘..
My 2003 corolla is rattling when is cold but stop few seconds and now the noise is too much my mechanic said i need new engine can you advise me please 🙏🙏🙏
Hello sure sound like you just need a new tensonador just like I fix this one , that's how this one star making noise on cool then it was there all the time
hola señor nestor, hace unos días cambie la junta de la tapa y vi la cadena y la presione hacia abajo y tiene un poco de juego pero no tanto como se muestra en su video. así que la cadena no debe de tener nada de juego al tacto? es la primera ocasión que veo su video y me gusto la explicación. gracias y saludos!!!
Lifters pressurize with oil inside them.. hence hydraulic lifters.. I’m pretty sure you gotta prime em before hand in a cup filled with oil and u squeeze em until you cant then put the pin in em and install..
Hello. I have a 2003 Toyota Highlander 4 cylinder with 210K miles. It runs good no problems, but there is a ticking after I shut the vehicle off. What could it be?...and what is an overestimate of what it would cost for a repair shop to make the ticking go away? Thank you
I did this to Scion XB it's easy. My Rav4 w/ 3GR-FE, V6 engine made this crazy chain slapping noise after oil changes last week. Now every morning cold start it making whizz noise like a bad belt. I'm afraid to start it in the morning.
Do you need to have the valve covers/spark plugs removed to replace this? Or can we just replace it without disturbing these items? Do you crank the engine in neutral? Thanks!
Tengo una 2009 matrix ....y suena igual .. Pero tambien se prendio El check engine .. El taller esta a 10 min ...puedo seguir manejando hasta llegar al taller ?? Me da miedo que sea la timing belt
Hey bro I have a 07 Camry it’s making that rattle noise coming from the belt area, so what exactly is wrong? I’m freaking out thinking it’s rod knock :/
Damn I did this but instead turned the pulley clockwise with out the serpentine belt on.And when I turned on my vehicle a knocking noise on the engine started up. Is my engine done for or can I re-do the procedure again but this time how you showed it on here?
Im about to re-do the whole process but this time I’m going to turn the engine clockwise with the serpentine belt on since I didn’t do it like that the first time. I’ll keep you updated
i have an intermittent rattle sort of noise (or the sound of shuffling poker cards) when i rev my engine in park and let off the gas pedal. I don't have any noise at startup but could this still be my timing chain or is it likely something else?
Did you ever figure this out, I’m in the same boat and we’ve already worked on the timing chain and it did not fix the noise, though it did seem to make it better
@@nestorautorepair I’m having this same problem but I’m not sure what to do idk if it’s just because of the oil because I’ve never had this problem just when it’s below 20 degrees
Hello, the rattle sound I get is when the car is in park and neutral and when you press the gas, about at 2000-4000 rpm there’s a rattle. Does the tensioner have to do with that or is it another issue?
Is recommended yes, but it it was not leaking don't worry about it, just add a small bit of atv on the small crack where the engine meet , some engine 2 corner some engine 4 corner
My 2008 Toyota Corolla was making noise and now the motor is spinning fast no start. Can you tell me if this is what it could be ? I've asked folks when it was making the noise and of course no one knew what it was, I guess I'll take the valve cover off and go from there.. I wish I had found your channel before it broke down ! Thanks for sharing and fingers crossed and hope I can fix her ..! Oh new subscriber too I will tell folks about your channel..
You're welcome boss thanks for your feedback ,, if I was you before removing the valve cover remove the spark plug and read the compression need to be 120 and up each sylinder
I'm between the vvti rattle or time chain lol I think it's the timing chain tho. It rattles on startup. Stops for a few seconds. Then randomly rattles. When I give it gas it rattles so I'ma check the timing chain when I get a chance
Yea...that's good one. I do appreciate your advice, good friend. Salute from El Salvador, Centro América. Tkank you for your pacience, big bro."MAY GOD BLESS YOU OVERALL"🙏
I received a 2009 1.8 Corolla to work on and the thing throws p0300, p0301 codes and other misfire codes P0302, etc. I have changed the oil and filter, air filter, spark plugs, the battery, I have tested the injectors, i have tested the Ignition coils, i have cleaned the throttle body and i have cleaned the mass airflow sensor. The car stalls out a lot and shakes. It also goes into limp mode if it shakes too hard. My cousin said it sounded like a rod knock, but i can't hear it that well. I do hear noise over by the timing chain, so im going to follow your guidelines and see if my chain is loose. Thanks for all of the info. I'll let you know if it solves my issue.
@@vindieu i have not found one person yet in any forum or youtube comments that said it wrecked their car. Seen some with over 200k miles and still makes noise on cold start n never caused issue
My 06 Camry is making this noise when I start it and drive till car warms up.. I’ve taken it to Toyota and they can’t find anything.. if it doesn’t get fixed will the timing chain break??
Hola yo tengo un 2008 Toyota Corolla ce y tiene low idle 500 Le limpie el throttle body y cambie las spark plugs y pvc y sigue lo mismo el throttle body es electric me puede ayudar con el problema y no tengo check engine light on
Hola Juan me Suena coni queens esta falta de gasolina trata de medirle la pression del gas, oh tambien trata de limpiarle el mass air flow . Pero cuando hay problema en un carro y no hay codidlgo el 90% ba ser gas . Purse ser bomba de gas mala. Injector tapado, filter de gasolina tapado
I did the same with my 2.4l toyota 2 years ago. Problem fixed.
All pro techs said that VVTi had to be replaced (only several grand with labor) lol!
Don't forget to properly reset the new tensioner by slightly rotating the crankshaft in the opposite direction. It will open the little hook on the tensioner and allow it to extend and self adjust.
My 2012 sounds some what. Not sure.
Two different issues bro
I have that problem on my 2003 avensis 1.8 petrol
“Can’t move this by hand”…..*moves by hand
😂 crazy
Thank you for this video,my 2005 corolla started making the rattling noise , now I know the problem. Mine the noise is there constant even when I have driven the car for long, the noise doesn't go away.
did this fix it?
Your my hero ! Appreciate the “tensioner” part itself , needed to retract mine 👍
Thanks
Thanks for your help, I'm going to buy a 2007 Corolla with 250k on it and the chain tensioner needs changed. With your help, this will be a breeze.
You're welcome boss , thanks for your feedback
My f*%#ing hero I'm having this same problem in my 09 Matrix. The TSB on this advised replacing the whole timing system - an actual nightmare. Thanks a lot!
You're welcome boss ,
Thanks for your feedback
Nice work. You can also release the hook from the tensioner with a screwdriver since you had the valve cover off, which is not required to replace tensioner, but the factory service manual recommends it just to be 100% sure hook is released. I have the same engine with 226,000 miles. You can also rotate opposite direction like 15-20 deg which will tension the slack side of timing chain and press on tensioner, releasing hook. Then turn clockwise.
Great video! Helped me fix my wife's 2009 Corolla
You're welcome boss , I'm so happy to head that you fix your wife car using one of my video, thanks for your feedback 🙏
Nice work 👍 I have 2008 Scion xB 2.4 L would this be the same procedure to replace on my car?
Yes thanks I'm sure they are the same
Great video. My 2010 Camry SE just started making that rattle noise a week ago. 90k miles. Definitely will check the tensioner out. 👍
You're welcome , thanks for your feedback
Did you ever get it fix?
How does you car only have 90k miles on it?
That's what everyone always asks me. It has just got 100k last week. I work about 15 mins from home. I've driven it up the So Cal coast a few times but mostly to and from work. It's been great to me.
@@gregarizmendez5275 they’re great vehicles. ✌️ Camrys are also good.
So you didn't replace the chain with a new one? And the tensioner magically got the slack out of the chain between the two gears?
So that means there is no noise when a chain overlaps gear teeth to get tighter from the tensioner?
That would be great if that was the case!
Excellent video! Do you know if the chain tensioner on a 2012 Honda Fit is similar to change out? Thanks for your info.
Thanks no on Honda they are inside
@@nestorautorepair OK, thanks for the info. Keep up your great presentations.
Got the same rattling on my 06 matrix, changed the spark plugs and it helped a little. Gonna do this next. Thanks!
Ok boss good luck
They didn't even show the sound of what it sounds like
I just got my mom a 2009 scion xb and it's making crazy noise and it's has great power! But that noise! She gone love it! I was gone change the whole engine thank you so much!
Thanks for your feedback boss
Buenas tardes vi sus vídeos y tengo una pregunta tengo una Toyota venza 4 cilindro y me ace lo mismo.dónde está ubicado el tensor de la cadena de tiempo?
Hola Buena que año es?
@@nestorautorepair buenas 2009
@@nestorautorepair buenas tarde es del 2009 4 cilindro
Sino lo miras en El MISMO Lugar ESO lo tienen adentro lo lo puede aceder asta que quite la tapa del timing
@@nestorautorepair Ook gracias
Hi Nestor. I replaced the timing chain tensioner and followed these instructions but I was told later that after installation and spinning the crank clockwise, you’re also supposed to spin it counter clockwise. I did not do this and heard a loud rattle at first start up but it went away. Is it necessary to spin the crank clockwise and then the other way for proper tension?
No that's not true bro , never go back
@@nestorautorepair thanks for that peace of mind!
You're welcome boss
Guessing you've already done this repair buddy but yes the Toyota manual specifically says to turn the crank anti clockwise until the hook on the tensioner unlocks. This should only take a very small amount of rotation and you'll hear the click. Then crank clockwise to extend the tensioner, you'll hear a series of clicks.
Yes
I have 1015 toyota avalon same issue ruttling in every start do think I have same tensioner and where is located in V6 3.5L engine I need help please
Hello I think on the V6 you need to remove the timing cover
@@nestorautorepair so , is not DIY job here in ny the mechanic tells you to change the engine instead of lot hours of labor
Wow
Nestor todo bien? Tienes algun video mostrando como suena cuando el tensioner no esta bien? Gracias
Even a brand new one will move by hand. It's supposed to. The only time that the tension increases is when it is installed and the oil going into the tensioner increases the pressure/ tension on the chain.
Hey, do you think a long drive where the oil is burned below the stick would cause the rattle to start? My 09rav4 is rattling a bit now after a 5k drive. Oil is below the stick so the oil needs a change. Hope it fixes the sound at the same time.
@@Justin-op8gghappened exactly like that to me, rattling started afterwards. Guessing the tensioner got wrekt
Great video, thanks! Did you replace gears also? I heard to always replace gears when you replace chain and tensioner..
Hey thanks ,, I only replace the tensioner and car still driving good no noise at all
I usually use Toyota OEM but in this case, that’s the part that failed. Have you had good luck with that brand of aftermarket ones?
Still running I just did a fuel pump on this car last week
Toyota updated the cam gear design as well as the guides
Nestor, thanks for the video. My 2002 Rav4 2.0 liter is rattling and I suspect it's the chain but haven't looked to check the tension yet. It starts rattling about 30 seconds after cold engine starts running. i will check under valve cover tomorrow. Do you have any advice on that particular engine and part replacement if that is for sure the problem?
Thanks again.
Yes sir they are all the same , if you want you can take the serpentine belt off and start the car to make sure the noise is not outside
@@nestorautorepair oh yeah I definitely did that already and it wasn't. Btw what a bitch to get that belt on haha. Awesome man thanks.
Lol yes sir any time
Hello thanks for the video. My toyota wish has a rattle when idling and low speeds which leaves on acceleration, could this be the issue as well? Thanks
Hi Yes it can be
I have a 98 Camry makes the same noise what kind of timing chain does it carry is it the mettle or the robber belts thanks for that video..
Your 1998 Camry takes timing belt rubber
That chain looks really loose, so I’d imagine it’s got a constant rattle right? My rattles for a split second on start up. Do you think it would be worth me bothering with it at the moment or just keep a ear out to see if it gets worse then fix it? Like I said, it’s only on start for about a second then no rattle and smooth operation. I have the 2013 Toyota Corolla.
Yeah that's how it start and it will get worse just keep an ear on it yes
@@nestorautorepair Cool, thanks 🙏
Yes
I think you should replace the tensioner ASAP. If it keeps getting looser you’re gonna have metal on metal and pieces of the sprocket are going to break off and end up in your oil. Then you have to replace the sprockets too and that’s an all day job maybe even two for some people! $$$
Ok
Hi, I have now a short loud rattle after cold start. But if I turn it off and on again, there is no short rattle anymore. Do you think it's the tensioner or the VVTi-camshaft making this noise?
I will say the tensonador
Vvt selinoid if it was happening every time it would be thetensioner
Ben, did you find a fix to your issue?? Please help me if you did. I think I have a similar issue. It comes and goes. Even if I restart the engine. Strange. I checked my vvti solenoid and cleaned it. Works perfectly when checking with electric current
@Ben Teyssen
Did you find the problem. And solved?
Hi there
Do you have any workshop ?
I do know yes
how did you get slack out of a chain with two sprockets that are suppose to move at the same time. is it still in time.
The tensoner will do the job
You didn’t show where you put the tensioner. What exactly did wrenching that wheel do? I’m confused.
By turning the big wheel it to make the tensioner come out to the max
Good job bro, I have a 05 vibe pretty much as a matrix same engine . So when I start it's making the rattle sound like it's coming from pulleys I change power steering pump and new altenator and it makes same sound , so I guessing it's the timing chain is loose.
Yes sir I'm sure this will be your fix, thanks for your feedback
My car doing the same thing Toyota Venza 4 cylinder . I've checked everything under the hood and change heat shield, still have a loud rattling when first cranking up and when give it the gas
Does that noise happened in the cold weather or it happens all the time. I have similar noise on my 2009 Corolla but not sure it is starter or chain. The noise sound like, when car starting and I try t start again like starter gear hit flywheel gear but not 100% sure. So far, It seems like only happen in cold or car stayed over night. After car warm up, no more start up noise. Thanks for the video. Thanks in advance.👍
This noise was there all the time but stronger when you first start the car
@@nestorautorepair Thanks for the information.
You're welcome boss
Does zuiko timing kit could be used to replace parts ot its better to chouse the original parts?
In my own car toyota camry 2003 the chain is hitting the side timing chain side cover. Can it b caused by this same part
Same problem , but open the top and make sure the top guide is still there
Questions for Nestor Auto Repair... Why did you use a socket and wrench to manually turn the engine to get the tensioner to release? Why didn't you just turn the engine using the ignition switch?
I've replaced the timing chain tensioner and the intake VVT gear and yet still the the VVT rattle on cold starts. The top chain guide showed no wear. Why? I change my oil every 4K and owned the car at 20K miles. It now has 92K miles. No check engine light for the VVT solenoid.
Maybe one of the side guides is broken
Wassup Nestor I have a 2010 Camry 4 cly and I have the rattles upon cold start it’s sucks!
What’s the difference between the vvt cam gear rattle and the timing chain tensioner rattle?
Also if it would be the tensioner would I need to adjust the timing or double check the at any point?
Hello well for the vvt your will get a code and also the rattle will never go away ,, if there is no code for timing you don't need to adjust it just add the new tensoner
@@nestorautorepair but in the 2010 Model the tensioner is behind (inside) the timing cover?
Yes you are correct 2010 has it inside it will require to remove the side cover
@@nestorautorepair is it better just to go the hole timing chain kit since i would already be going thru the trouble?
Sure to be safe just do the new kit
thank you. what kind of jack is that? do you have a link?
Thanks sure I will send you the link later today
Link?
Hearing an occasional rattle at idle.....not sure if it's a water pump going bad or this tensioner....it's on the same end of zthe engine as the belt drives. Scion xA first gen. Is there an easy way to tell which it is?
So my 2003 corrola had that rattling and then one day it just didnt turn on.. i took out the valve cover and it has that same slack on the chain, should i try replacing tensioner first or should i just replace the chain and all?
Well if the car still crank it need a new chain because you want too long and the chain stretch and jump timing , but if is not cranking then it may be way too late engine lock up. Hope not
@@nestorautorepair okay thanks, yes it cranks and sounds like it wants to start, i havnt checked the timing yet, im just going to do the whole timing chain job.
Yes is got too loose and it jump timing
My chain makes a noise on my manual 2003 Viti RAV4 it comes and goes but it’s revving or stalling at lights etc... is that tensioner or chain ?
By the way love your no fuss way of getting to the point
Start with the tensioner first
@@nestorautorepair thank you so much!
U are welcome
Thanks Nestor! was a big help, staright forward simple.
Thanks for your feedback
Will the chain always be loose between the camshaft gears or can it be loose below and still be the problem? I checked mine and it was tight up top.
Need to be tight all the way
I have a 2012 Camry SE and I’m sure I have this problem. How much does it normally cost to replace this?
Not a lot under $100
If your chains been beating against something and loose shouldnt you replace the chain also?
Hi, good video. Did this fault make the check engine light come on?
Thanks boss no light ON , but if you are getting code for timing then more likely your timing chain guides broke
I just put a new valve cover gasket in maybe 700 miles ago on my corolla do I still have to put a new one if I do this job ?
Not really if you did not add silicone you are good to use it again
Good video! How to tell if the noise is from the chain or VVTi please? Thanks!
The chain tension and slack is the reason for the noise either way and the tensioner could be getting weak and the vvt makes it tremendously worse
Is this suppose to be done for maintenance?
Not really , this will happen when you don't change your oil on time or use cheap oil
@@nestorautorepair Thank you
You're welcome boss
So I don’t need a whole new chain? This tensioner should be able to solve it?
Corret just get the Tensioner and see
Just ordered one, thanks for the vid hopefully it’ll solve it.
Yes sir
@@nestorautorepair it didn’t work!
Is this a 2.7
1.8L
Sir i have 2007 toyota with 1zzfe engine . When is stop car or in neutral then i heard a noise like a diesel engine plz refer me that's the noise of tensioner also ?
Mmmmm let me send you another toyota that I fix with a similar noise but it was not the same fix
ruclips.net/video/9PIAtC-JnlU/видео.html
Is this the fix for the chain rattle you can hear clearly when the engine is idling? I have that weird chain noise that sounds like something is loose inside the engine in a 2011 Rav4
Yes this was the fix
Did it ran like a top n not rattling anymore after a new tensioner installed?
The car come by last week still running strong no rattlering at all
My toyota corolla 2009 having rattling noise on cold start for 10-15seconds, Mechanic told me to change complete timing chain...
So should I change Complete chain system.... or just Timing tensioner ? Please help 🆘..
Just the tensonador will do it if that's the noise , don't spent all that money on a new chain
@@nestorautorepair okay ..thank you so much for your reply ♥️👍
You're welcome boss thanks for your feedback Anand
My 2003 corolla is rattling when is cold but stop few seconds and now the noise is too much my mechanic said i need new engine can you advise me please 🙏🙏🙏
Hello sure sound like you just need a new tensonador just like I fix this one , that's how this one star making noise on cool then it was there all the time
@@nestorautorepair okay thanks sir
You're welcome let me know please how it goes
@@nestorautorepair okay thanks a lot i will let you know
Ok thanks , best luck
Were you able to find the error codes on engine. I have a rattling noise also on my 2007 corolla and it says fault code p0012.
Yes
My 08 Yaris is making a rattling sound but only on acceleration at lower rpms. Do you think it is the same problem starting?
First make sure there is good loin and level is good
Did you ever figure out the cause of your rattle on acceleration Rob?
hola señor nestor, hace unos días cambie la junta de la tapa y vi la cadena y la presione hacia abajo y tiene un poco de juego pero no tanto como se muestra en su video. así que la cadena no debe de tener nada de juego al tacto? es la primera ocasión que veo su video y me gusto la explicación. gracias y saludos!!!
Hola Efrain si la cadena tiene que estar Bien dura nada de movimieto, gracias por ver mis video ,, saludos
@@nestorautorepair gracias por su respuesta. Se lo agradesco. Saludos!!!🙋♂️🙋♂️🙋♂️🙋♂️
De nada brother suelte!! 💪
Lifters pressurize with oil inside them.. hence hydraulic lifters.. I’m pretty sure you gotta prime em before hand in a cup filled with oil and u squeeze em until you cant then put the pin in em and install..
My O7’ Corolla is making a rattling noise but only when it is in gear (it’s a manual) do you think this is the problem?
is this a noise that goes away as you drive ? cause my rattling noise goes away .. it’s mainly in start up
No this noise will not go away if you are having the same problem.
Hello. I have a 2003 Toyota Highlander 4 cylinder with 210K miles. It runs good no problems, but there is a ticking after I shut the vehicle off. What could it be?...and what is an overestimate of what it would cost for a repair shop to make the ticking go away? Thank you
I believe that's normal that's the catalytic converter cooling down
@@nestorautorepair SWEET! I'm an idiot with vehicles. Appreciate you man. Subscribing right now
Thanks boss , we are always learning boss
Is there such thing as overturning the engine causing too much tension? when releasing the hook?
Not at all
@@nestorautorepair gotcha, thanks for the reply. Doing this soon.
Ok best luck boss
I did this to Scion XB it's easy. My Rav4 w/ 3GR-FE, V6 engine made this crazy chain slapping noise after oil changes last week. Now every morning cold start it making whizz noise like a bad belt. I'm afraid to start it in the morning.
Wow
Do you need to have the valve covers/spark plugs removed to replace this? Or can we just replace it without disturbing these items? Do you crank the engine in neutral? Thanks!
You can do without remove all of that. Can reach from behind the engine & remove and install the new.
Tengo una 2009 matrix ....y suena igual ..
Pero tambien se prendio El check engine ..
El taller esta a 10 min ...puedo seguir manejando hasta llegar al taller ??
Me da miedo que sea la timing belt
Hola si suena mucho , no lo maneje , echale aceite primero aver si la bulla desaparece
Hey bro I have a 07 Camry it’s making that rattle noise coming from the belt area, so what exactly is wrong? I’m freaking out thinking it’s rod knock :/
Also like the knocking increases when I increase rpms
Yeah same fix timing chain tensoner
If its 2GR- FE check the pulleys first, they usually make the rattle noise.
Ok 👌.... dónde está tu taller Nestor,?? Yo estoy en Lynn Massachusetts, conozco un taller que tiene ese nombre también, Noc si es el mismo,... lmk
Hola si yo estoy en virginia , eh visitado massachusetts si
@@nestorautorepair Ok bien , es que mi Toyota Venza v6 tiene un ruido por esa zona
Oh ok si puede ser que sea lo mismo , pero hay mucha cosas que pueden aser ese ruido
Will I need to re time the engine after changing the timing chain tensioner?
No you don't just rotate the engine like 4 times
@@nestorautorepair thank you
You're welcome
Bro how about 2011 highlander 2.7l what is the procedure for it?thank u u making siple very imformative video👍
I believe they are the same engine bro , so same process, thanks for your feedback boss
Tigre y no sera tambien el vvt gear??? E visto otros video que dicen que es la gear esa
No en este caso solo fue el tensonador
Damn I did this but instead turned the pulley clockwise with out the serpentine belt on.And when I turned on my vehicle a knocking noise on the engine started up. Is my engine done for or can I re-do the procedure again but this time how you showed it on here?
Wow , ufff I'm not sure if your noise is coming from internal
It’s coming from the inside. I took of the top cover and my chain had a slack on it I’m guessing that’s where the noise is coming from?
Mmmmm ok but did you fix it the way I did it with the valve off so you can see if you did it t correct ?
Im about to re-do the whole process but this time I’m going to turn the engine clockwise with the serpentine belt on since I didn’t do it like that the first time. I’ll keep you updated
Ok thanks
Nice work!! And, it's the same for a Scion xd 2008 ??
Yes sir Same, thanks for the feedback
i have an intermittent rattle sort of noise (or the sound of shuffling poker cards) when i rev my engine in park and let off the gas pedal. I don't have any noise at startup but could this still be my timing chain or is it likely something else?
Did you ever figure this out, I’m in the same boat and we’ve already worked on the timing chain and it did not fix the noise, though it did seem to make it better
Can this be done without removing the valve cover?
Yes , I just remove the cover to confirm the problem and the fix
@@nestorautorepair unfortunately this didn't cure my problem.
It did get a little quieter but, I'm gonna have to change the VVT sprockets.
My corolla rustling only in winter I’m from Boston but in the summer the noise gone?
That mean the oil takes longer to come up on in the winter , try to put lighter oil in winter
@@nestorautorepair I’m having this same problem but I’m not sure what to do idk if it’s just because of the oil because I’ve never had this problem just when it’s below 20 degrees
Well the first thing you need to do is take off the valve cover and see if the chain it has any play
@@nestorautorepair if chain has no play what would you consider it be
Rode bearing
Hello, the rattle sound I get is when the car is in park and neutral and when you press the gas, about at 2000-4000 rpm there’s a rattle. Does the tensioner have to do with that or is it another issue?
Take the belt off and see if the noise still there
@@nestorautorepair I’ll try that first. thank you!
Yes you welcome let me know
Yes that was the fix
When You give it gas does it make louder noise before you you fix the problem ?
Yes sir it did
Adonde te encuentras amigo??
Hola en Sterling va
@@nestorautorepair yo vivo en Virginia tambien veo q eres un buen mecanico estoy a 2.40 horas de sterling
Oh gracias,, donde tu vibes?
Did you had power loss before you fixed it? Because my Yaris has a rattle and has power loss as well
Not really
Do you have to change valve cover head gasket?
Is recommended yes, but it it was not leaking don't worry about it, just add a small bit of atv on the small crack where the engine meet , some engine 2 corner some engine 4 corner
My 2008 Toyota Corolla was making noise and now the motor is spinning fast no start. Can you tell me if this is what it could be ? I've asked folks when it was making the noise and of course no one knew what it was, I guess I'll take the valve cover off and go from there.. I wish I had found your channel before it broke down ! Thanks for sharing and fingers crossed and hope I can fix her ..! Oh new subscriber too
I will tell folks about your channel..
You're welcome boss thanks for your feedback ,, if I was you before removing the valve cover remove the spark plug and read the compression need to be 120 and up each sylinder
can I replace the tensioner without removing the valve cover?
Yes you can
Mine rattles only between 2200 and 3000 rpm, top engine rattle, could this be it? It's most present when at a steady speed on the freeway
More likely your upper timing chain guide is work out , take off the valve cover and check it out before replacing the tensioner
@@nestorautorepair also the engine has been sputtering a lot lately at red lights not sure if it's related
I noticed my Yaris 07 making rattle noise only when accelerating and only when cold for first 6-7 minutes. Later almost gone. Could this be tensioner?
Most likely yes
only if you had a video of how the noise sound. Now i'm stuck between water pump or timing chain tensioner smh thanks, great content
Take the main belt off and star the car and see if the noise still there
I'm between the vvti rattle or time chain lol I think it's the timing chain tho. It rattles on startup. Stops for a few seconds. Then randomly rattles. When I give it gas it rattles so I'ma check the timing chain when I get a chance
Wow ok we'll it can still be the here , open the valve cover and see if the chain is loos
@@nestorautorepair it was the timing chain 😄
Wow , thanks for sharing
Gracias por sus instrucciones de mecánica. Se le agradece Amigo.
De nada gracias por su Apollo
Yea...that's good one. I do appreciate your advice, good friend. Salute from El Salvador, Centro América. Tkank you for your pacience, big bro."MAY GOD BLESS YOU OVERALL"🙏
Gracias brother same to you
Will this make a ticking noise when accelerating? It sounds similar and my car ticks whenever I’m getting up there in speed
Yes but more like rattler noise
Ok mine sounds more like a click click click noise really fast, gets faster with speed also
Ok it can still be that
Might be im going to try it out anyways, cars older with 180k miles on it.
Best luck
does this fix this issue? (T-SB-0087-09) I get a grinding noise on every cold start and after the car has been sitting for about 2.5hrs.
Take the valve cover off and see if the chain has play
@@nestorautorepair thanks. I'll do that. What if it doesn't though?
If chain is good then we need to check the rode bearing
Also to be sure 100% if the noise is internal , take the main belt off and start the car and see if the noise still there
I've heard it internally from the engine.
My avensis is only doing this at cold start could it be this?
Yes
Do I need to replace the valve cover gasket?
Yes is recomende
I received a 2009 1.8 Corolla to work on and the thing throws p0300, p0301 codes and other misfire codes P0302, etc.
I have changed the oil and filter, air filter, spark plugs, the battery, I have tested the injectors, i have tested the Ignition coils, i have cleaned the throttle body and i have cleaned the mass airflow sensor. The car stalls out a lot and shakes. It also goes into limp mode if it shakes too hard. My cousin said it sounded like a rod knock, but i can't hear it that well. I do hear noise over by the timing chain, so im going to follow your guidelines and see if my chain is loose. Thanks for all of the info. I'll let you know if it solves my issue.
Yes sir thanks for your feedback , also make sure you do throated relearn
How do you perform throttle re learn on these? Do you have a video?
On Corolla you don't need to , only Camry needs it
Great tutorial.
What happens if we don't repair this can it break something?
Yes the engine will jump timing and that will be a done engine will need a new one, thanks for your feedback Dicofol
exactly as he says. this problem not repaired = wrecked engine, no salvation.
@@nestorautorepair not really bro. It will bend valves. Papi.
Ok papi
@@vindieu i have not found one person yet in any forum or youtube comments that said it wrecked their car. Seen some with over 200k miles and still makes noise on cold start n never caused issue
Where is the tensioner installed? It looked to be outside the block.
My 06 Camry is making this noise when I start it and drive till car warms up.. I’ve taken it to Toyota and they can’t find anything.. if it doesn’t get fixed will the timing chain break??
It will jump timing yes and damage your engine
Nice tensioner plate gasket....lol...thanks for the funny vids man!
How much to do this job and where are you located?
I'm in Sterling , $150
@@nestorautorepair dang...i would pay $300 to get mine fixed in Milwaukee. Thx for your response
You're welcome boss
Hola yo tengo un 2008 Toyota Corolla ce y tiene low idle 500 Le limpie el throttle body y cambie las spark plugs y pvc y sigue lo mismo el throttle body es electric me puede ayudar con el problema y no tengo check engine light on
Hola Juan me Suena coni queens esta falta de gasolina trata de medirle la pression del gas, oh tambien trata de limpiarle el mass air flow . Pero cuando hay problema en un carro y no hay codidlgo el 90% ba ser gas . Purse ser bomba de gas mala. Injector tapado, filter de gasolina tapado
Doesn't the timing get off when you crank the pulley with the car off?
No
Not sure if the tensioner is my problem, the rattle is not very loud and only lasts a second but I can hear it and it's annoying lol
So you turn it one whole turn clock wise?
Yes