How to repair vinyl shutter anchors that have broken off.
HTML-код
- Опубликовано: 1 окт 2021
- Vinyl shutters become brittle and anchors snap off in the wind. This method of repair will help you fix this problem... #shutters #homerepair #diy
Хобби
Хобби
thank you for making this. In my situation, I was working on a 2nd story roof with a long extension ladder. The pliers + screwdriver trick really helped. Just seeing it made it possible for someone who is not excited to be on a high ladder to get this done.
Great news Steven! Thank you for letting me know...I stir clear of those ladders anymore...just tripping and falling on the ground hurts enough :)
I hear u about high places like on a ladder, I would just as soon stay closer to the ground...thanks Steven!
You could also use a screw into the plastic end that stuck flush in the mortar and pull it out with a hammer claw.
@xxcysxx yes...good idea, I appreciate ur input! :)
Thank you for this video. I'm looking to replace the old shutters on my home. One of the old ones has a pin that broke off flush with the brick. Appreciate the lesson.
Ok....U r very welcome!
Just what I needed thanks.
Sure thing...glad to help :)
Thank you sir. Your video was extremely helpful for me. 👍
Very cool Chuck...that was my intended goal!...enjoy ur day :)
Thanks for the information..
I hope it helps out Daniel...u r welcome :)
I love RUclips! Anytime I have a problem, YT can solve it! One peg fell out and I let it go and after a day the rest broke off flush with the house and were stuck in there!
U r exactly right...most times RUclips has a video about what a person needs help with...it's an awesome platform...thanks for dropping by! :)
Great video 👍
Thank you Henry...I appreciate u taking the time to let me know...very cool! :)
Thank you!!
Sure thing...I'm thinking this wind around the country has quite a few shutters torn off...
Thanks for making this. It was helpful. I replaced all my shutters in August of 2022, and they worked great. I noticed today that the anchors on the top half of most of my 13 shutters have now broken. I have no idea why they would have broken. They went in and snugged up just fine when I put them on originally. Any thoughts on that?
Hello...most times I see them broke is because of wind getting in behind them time after time which will eventually weaken and snap them off. Secondary solution would be to remove the plastic stuck in the hole with a long drill bit then tap in a wooden dowl piece that will come out at the edge of the brick...pre-drill the dowl then install an exterior wood screw with a stainless steel washer...touch up with matching paint and that will hold well, besides that I'm not sure what else u could do...?
@@laffilmfest3759 that’s great advice. Thanks. I think I’ll try one more round of regular anchors and adjust if it happens again.
U could try squirting some exterior caulk in the hole first then the anchor...won't keep the anchors from breaking but allow them to fit more snugg
@@laffilmfest3759 brilliant! Thanks.
Love the video do all vinyl shutters comes in one sizes??
Hello Nicole, most are the same width and then there are usually about a dozen different lengths...and a half dozen stock colors...home depot, lowes, menards all have them...average price is about $50 per set...maybe a little less
@@laffilmfest3759 thanks
U r welcome :)
If you felt the need to drill the old fasteners out, what size bit would you use?
Not really sure Josh. Always start small like a 3/16 and see how that does...sometimes u take the center core out the rest collapses and falls out...but be real careful, the older the shutter the more brittle they become...like an egg shell...let me know what size worked for u .
@@laffilmfest3759 I’ve heard as well to start small, even smaller and then end up at 1/4”
Do you ever use any construction adhesive or caulk or something in the hole to help the replacement pin grip? I have some shutters that have blown down and now the the pins don't grip as tight (the fact that the mortar is really 'sandy' doesn't help). Anyways, thanks for the video...
Hi Shawn...several fixes for that...u could use a caulking gun and fill the hole with caulk then push the pin in while the caulk is still wet, once the caulk is dry it will hold good, caulking is like an adhesive, just a latex caulk would work fine, another solution would be to tap in a wooden dow pin and cut it flush with the brick. Then predrilled the pin and install a exterior construction screw with a stainless steel washer...touch up the screw to match ur shutter color and u r done, lowes or home depot could make u a sample color for $5...nice thing about doing it this way is u can remove the shutter to paint if u wanted too...hope this helps. Of course u could also just tape in like a shim piece to take up room then tap in ur shutter pin :)
@@laffilmfest3759 I appreciate the suggestions! I think I'll try the caulk idea first. I just wasn't sure how well caulk would 'hold' to the mortar. Have a good day!
@@laffilmfest3759 This is exactly what I was looking for. I replaced my vinyl shutter that had blown off, and now it's blown off again, pulling the new fasteners out with it. Luckily it didn't break, but I'm going to put caulk in the holes first.
U could fill the hole with caulk and set the plastic anchor as long as u have a way to hold the shutter tight against your house until the caulking sets up( 2 hours), or, shave splinters from like a paint stir stick and hammer a few inside the hole, then ur anchor will fit better, but if the hole is really sandy and much larger then the original size I would probably figure out what wood dowel size would tightly fit in there, then forget the plastic anchors and get something like a deckmate exterior screw and couple it with a stainless steel washer, predrill the dowel pin once u have installed it...then install the shutter with the screw.. nice thing is u can always remove the shutters to paint...I hope this helps...clear as mud I know :)
@@laffilmfest3759 That's a good alternative, because I wondered what would happen when the next storm came up and this time the shutter broke. I would not want to drill out the hard caulk!
I was told that the anchor has bored out the hole so it can’t take hold. What can I do?
Hi Brenda...u have several options, with a caulking gun or hand held squeeze tube fill the hole with a latex caulk...then while the caulk is still wet insert the anchor, make sure the shutter is tight against the house by pressing on it or leaning like a ladder against it until the caulk dries(2 hours dry time)...this should hold, u might need a washer on the pin if it had pulled through the shutter, second option is to hammer in a piece of wooden dow rod into the hole...cut off flush with the brick( I'm assuming it's brick) then drill a small pilot hole in the center of the dow pin...then install an exterior screw with a washer...touch up with a little paint...good to go, it will look a bit different from the other pins but believe u me with everything happening with life u will soon forget that little detail...hope this helps :)
What if my shutters are warped?
Hello Gina. Not a good scenerio :(... vinyl shutters will warp especially if they are facing south and painted a darker color. U might be able to pull them tight against the house but they may remain wavy...the big box stores sell lots of sizes and a variety of colors...some are sold as printable shutters but if u rough them up with sand paper and apply a good exterior primer/paint most of them should hold up...keep in mind the lighter the color the less heat they will absorbed...thanks for swinging by the channel :)
This didn’t help tell me how to take the broken piece out of the brick wall
Couple things to do if broke off flush: take a drill bit just a little smaller then the anchor and drill the old one out, or, shoot a screw into the center of the broken one and with a prybar or hammer claw pull it out
That is so smart!!!! Thank you!!!!!@@laffilmfest3759
It’s called a fulcrum-the point on which a lever rests or is supported and on which it pivots.
Poor design…great for the pin makers.
Yes...I agree, there has been many times I have removed the plastic pins and went with dowel pieces and exterior screws...then the shutter can be removed and replaced easily, thanks Patriotone!
Plastic
Hello...plastic???