I'd suggest taking some of your left over foam and inserting inside your PVC pipe before gluing it together. If you spring a leak, those pipes will all fill with water and cause you to sink. Foam inside would keep that from happening. Great design -- I've always wanted to build something like this.
Problem is filling it with foam will greatly reduce how much weight the boat can hold. You would need to use maybe a 16 inch pipe to make up the difference in lost buoyancy. A couple dozen life vests would be cheaper.
I know he was struggling in the boat because one is he shouting the video by a hand another is that he is giving accelate to the motor he is great person 👏 👍 nice I will support you we all are there
¡¡Qué maravilla y qué despliegue de ingenio!! Se demuestra un talento impresionante al diseñar y construir algo así. Un fabuloso medio de transporte por muy poco dinero. ¡¡Felicidades!!
Nice simple design! Great. I’d like to see some smaller tubes mounted underneath the two bottom sides. That would give it lift and act as rail tubes to ride on
Nice idea and build, the only things I would do diferrently would be to run a reinforcement from the motor mount to the wood at the stern and because I'm probbly twice his size would have been to upscale the boat and used a full sheet of foam for the main area and then two lite layers of fiberglass, because it's something I'd keep for quite awhile to fish from. Oh yes, and also would install a small aluminum beach chair, the type with short legs, into the deck to keep my old butt from getting too tired. Thanks for sharing.
I too would make it wider and longer. If you added 2 T's at the fore and aft thwarts to make two more beams you wouldn't need the foam...which is just going to break up and pollute the waterway. I think you could then make the prow a bit larger and add a T to each side but pointing inward and then connect to another 90, kind of reversing what he did to make the prow and then you would definitely have plenty of buoyancy. Then, I'd fill the insides of the pipe with spray foam to make is unsinkable in case of a crash. Cool idea though.
I had the exact idea, using the PVC PIPING same 200mml wide, except slightly different design. yours is simpler, and goes great! trouble is, if u are a much heavier person, might not go quite as good!!! Haha... well done, love to see other people's ideas
Thank you for such a wonderful video. Your channel is an inspiration for me to create a channel with similar contents. I hope that you look at it and give me your comments. Keep up the good work. Stay blessed and stay safe!
@@sakutaazusagawa208 aircraft needs an Airport or a large place to take off and Land. Big drone need to take off and Land verticaly. He needs 4 big motor, a battery, a controller, à stabilizer and thats all
Great boat. A keel might keep the boat from going side to side so much. That wood looked soft. Old pallets have hard wood. Every screw should be dipped in sealer to keep water out. Don't use power tools and flip flops.
If the tubes are water tight, adding foam or bottles would decrease the buoyancy rather than increase it, as they would add weight. Nothing would be more buoyant than air except perhaps a lighter-than-air gas like helium or hydrogen.
@@vivangreco1710 dont forget if the pvc had a good seal on it, you could pump out air and create a vacuum. Lighter than air means air at a lower pressure than 1 atm. If you could get it to a pressure of -7 psi, you might recieve somee bouyancy, there. Evacuating the air pressure would be brilliant. So flip the pump to deflate and pump that air out. You would need a one way valve flipped in reverse to achieve that and bouyancy would be increased withiut needing to fill with air. Aside from the raft now having less weight because of the weight of air, its macro density would decrease. The voids would i increase in bouyancy. If it was a very poweful vacuum, an elephant could not sink those pipes. Dont forget to have multiple chambers , on case a seal breaks. That chamber would take on water very fast. So this set up would require decent seals and many chambers, preferred. In order to put a lighter than air gas in those pipes, you would have to evacuate some air in them, creating a vacuum. At that point, o adding of any gas would be heavier than the vacuum, itself. Sense the walls are rigid. I love the idea but helium would juat be heavier to add in there after creating a vacuum to add any other gases.
Pretty cool. Curious, what would the cost be on this project? Did you by chance have a ballpark figure? Like others have said, pvc used to be cheap. Not no more. Great build
Yes, very simple and practical. Could use polyurethane to fill up the pipes, aluminium screws and marine ply and a sheet of polythene to cover up the Styrofoam. By the way, which size of pipes is he using 4" or 6" ? Also, I wish I was able to source a 2- stroke boat engine locally.
I would have made it 1 foot wider and 2 feet longer. Afterwards I'd wish I had made it 2 feet wider and 4 feet longer. Only to regret not making it 4 feet wider and 8 feet longer. It never ends.
So glad to see you use safety sandals, many people don't but you do! ;)
Those sandals very important. Lol
Ive been to places in the world where they do welding, concreting and high level building work in bare feet and t-shirts, no welding goggles either.
@@stephanguitar9778 what?! no safety sandals??
thats how you do in se asia.
Under rated comment👌😂😂😂
You deserves an award for your ingenuity....!!!!
too coool.... and the best part is him cruising the river filming himself thinking, "yeah, i'm bad... i'm bad". very good, bro!
Nice little boat. I would want it bigger so 2 or 3 people can go on it. Thanks for posting. Great idea. Lightweight and low maintenance. Perfect boat.
I was thinking using all the foam blocks = wider, more stable, and a stronger motor mount to withstand motor vibration and torque.
This is absolutely too cool! I love your ingenuity! 👍😎
I'd suggest taking some of your left over foam and inserting inside your PVC pipe before gluing it together. If you spring a leak, those pipes will all fill with water and cause you to sink. Foam inside would keep that from happening. Great design -- I've always wanted to build something like this.
Hahahahahah...
Great idea. When the boat is sinking is not the time to wish you had some extra buoyancy.
the weakness is especially with the torque on those fittings from bouncing wave impacts.
Onde qui e qui eu encontro izopor dessa grossura
Problem is filling it with foam will greatly reduce how much weight the boat can hold.
You would need to use maybe a 16 inch pipe to make up the difference in lost buoyancy.
A couple dozen life vests would be cheaper.
This is a great design as the frame not only gives rigidity, but also buoyancy as well. Awesome!
I know he was struggling in the boat because one is he shouting the video by a hand another is that he is giving accelate to the motor he is great person 👏 👍 nice I will support you we all are there
¡¡Qué maravilla y qué despliegue de ingenio!! Se demuestra un talento impresionante al diseñar y construir algo así. Un fabuloso medio de transporte por muy poco dinero.
¡¡Felicidades!!
Nice simple design! Great. I’d like to see some smaller tubes mounted underneath the two bottom sides. That would give it lift and act as rail tubes to ride on
Wow, absolutely smashing job! All you need now is a luggage rack and an umbrella! - Jeffeo
Ingenious! Your boat is so lightweight, it floats like a cork! Bravo!
Buenicimo. Me gusto ese practico modelito. Pará la Pesca... Me voy a construir uno de esos.... Gracias por compartir la Geñal Idea... 👍👍👍👍
Thank you for sharing and teaching me how to make a boat using PVC pipe.
Great result. I’m going to do the same design here for river fishing 🎣 thanks for sharing
Кандинга ур бола зур уйлаб чикорибсан 👍👌молодец супер
Nice idea and build, the only things I would do diferrently would be to run a reinforcement from the motor mount to the wood at the stern and because I'm probbly twice his size would have been to upscale the boat and used a full sheet of foam for the main area and then two lite layers of fiberglass, because it's something I'd keep for quite awhile to fish from.
Oh yes, and also would install a small aluminum beach chair, the type with short legs, into the deck to keep my old butt from getting too tired.
Thanks for sharing.
very cool, just gotta find some free pvc. I've checked on price of anywhere from 6" to 12" pvc and it would be cheaper to buy a boat. Cool video
PVC ain't cheap
Especially now with the price of oil
Good luck finding some for free I tried this 5 years ago
That was 11 months ago brother you should check now it would blow your mind
Wow.... Very nice project.. I like it..😀😀😀😀
Very nice. Looks durable, stable and sturdy
SUPER GREAT JOBE BUDDY ''' THANK YOU SO MUCH FOR THE IDEA MANY PEOPLE NEED IT HERE IN MOROCCO TO CROSS THE BORDERS TO EUROPE !!!!!!!
Cunny funt
Lord help me I'm dieing from laughter
@@monstergaming5454fuck wrong with you bro
недавно переживал что этот мужик может пострадать от короны, хорошо что можно снова как и раньше переживать из - за самоделок, развалятся или нет)))
Молодец так держать!!! Привет с Украины.
Needs a chair a rod holder a rod can of worms ,an umbrella a pretty girl.Great job!
and beer.
WOI, PADU 👍👍
Never thought, PVC pipe is useful in that many ways 😊
ruclips.net/channel/UCYZq90s29Jy4jfAULKkhT3Q
sx ruclips.net/video/6_2FmtsOiE4/видео.html
Next step would be wind musical instruments from PVC! Imagine a Clarinet from pvc!
anjriiiitttt kerennn bangetttt.. buat mancinggg.. sueeee. cuman pake pralonnn toppp 👍👍👍👍👍👍
Great vid, a boat that can be thrown in the bed of my truck, no trailers needed.
Love from India,Assam😠
Parabéns pela criatividade muito simples e prático nota 1000
Руки растут откуда надо.👍👍👍👍👍клево получилось
I love in the ingenuity Brilliant!
Well done man! Impressive... I'm beginning to think... that the users of pvc pipe.. are nearly endless!
Good idea and very simple. You are amazing👍👍❤
Yes it good
@@nf_faerroyos416 0
Di
@@nf_faerroyos416 น
Brilliant,this could be the design I need for our annual Village raft race,no motor but paddles 😊
I like how he is impressionless after completing a project no happiness or excitement he be like "we do this shyt everyday boi" 😂😂😂
you mean expressionless? yea he's not expressive but i bet he's content. I made a pedal boat and it didn't turn out so great
8:53
I’m dead so tru
আমার কলিজার নবীর কি সুন্দর একটি নাম ❤️❤️❤️❤️❤️❤️ হযরত মুহাম্মদ সাল্লাল্লাহু আলাইহি ওয়াসাল্লাম ❤️❤️❤️❤️❤️
That’s awesome. Now I want to make one lol
Creative channel yep yep yep you are creative indeed
Looks awesome! Now it needs a roof and solar!
Sangat bagus keren,,,, salam dari Indonesia 🇮🇩🙏👍
I too would make it wider and longer. If you added 2 T's at the fore and aft thwarts to make two more beams you wouldn't need the foam...which is just going to break up and pollute the waterway. I think you could then make the prow a bit larger and add a T to each side but pointing inward and then connect to another 90, kind of reversing what he did to make the prow and then you would definitely have plenty of buoyancy. Then, I'd fill the insides of the pipe with spray foam to make is unsinkable in case of a crash. Cool idea though.
Show us don’t tell us
I had the exact idea, using the PVC PIPING same 200mml wide, except slightly different design. yours is simpler, and goes great! trouble is, if u are a much heavier person, might not go quite as good!!! Haha... well done, love to see other people's ideas
Very efficient, inexpensive and safe! I could see the wave created by the boat is minimal.
Kereeeen..perahu dari pipa ...mantap👍👍👍
Parabéns, muito bom 👏👏👏
Woww good job fantastic small pipe PVC boot
Nice Job!! You need to add a lounge chair and a drink holder!! :)
Good idea
Very beautiful. Thanks
Thank you for such a wonderful video. Your channel is an inspiration for me to create a channel with similar contents. I hope that you look at it and give me your comments. Keep up the good work. Stay blessed and stay safe!
ruclips.net/channel/UCYZq90s29Jy4jfAULKkhT3Q
Nice boat 👌👌👌
Sensacional... parabéns pela invenção... vou fazer um barco igual a esse.
Tiu are a genius for all project
Thank goodness he is wearing his OSHA approved steel toe safety flip flops!
Nnnnnnnnnnnnnnnn!
🤣🤣🤣🤣🤣
i,am,your,very,big,fan
Упор крепления двигателя нужно было делать ещё и к "соседней" горизонтальной доске , а так однажды двигатель уплывёт отдельно от всей конструкции 😊
You are a creative man👍🏻
Awesome build, looks easy to build. How long did it take you to build?
👍👍💯✌️
Almost two month hard work.Ahaha how unusefull are you?Why you ask moron,two or three hours its enough.😂😂
12 minutes 😎
You are the King diy !
Would be fun to watch him build a real ultralight airplane and fly on it
U mean a human drone isn't ?
@@luccanamps6668 no, I mean an actual flying machine, that can fly and be piloted by an actual human being
@@sakutaazusagawa208 aircraft needs an Airport or a large place to take off and Land. Big drone need to take off and Land verticaly. He needs 4 big motor, a battery, a controller, à stabilizer and thats all
Peter Sripol did something like that
@@bentleyc5646 I saw that. That's infact the reason why I said something like this in the first place
Брат ,тебя там рыбы ругают за такой мотор..Он не только шумит но и вибрирует.
Слов нет КЛАСС☝️👍
Wonderful Invention! Where can you get such large PVC and that great motor?
GRANDE IDEA
👍👍👍👍
Great boat. A keel might keep the boat from going side to side so much. That wood looked soft. Old pallets have hard wood. Every screw should be dipped in sealer to keep water out. Don't use power tools and flip flops.
Also seal the wood so it doesn't rot
Just one word it's amazing,,,,,;;!!
Is this avail on amazon yet?
Fantástico, muito bom.
😍😍😍😍😍😍wow very nice man I like it I am very excited for you nice to meet you a man I'm so happy with😍😍😍😍😍
That is an excellent job. I have never seen PVC pipes cut with a chainsaw before, hahahahahaha.
😂😂
You are a nice CREATOR
Cool boat.... I f I build one, I think I’ll pack the pvc tubes with plastic bottles and insulation spray foam to add extra bouyancy
If the tubes are water tight, adding foam or bottles would decrease the buoyancy rather than increase it, as they would add weight. Nothing would be more buoyant than air except perhaps a lighter-than-air gas like helium or hydrogen.
@@vivangreco1710 dont forget if the pvc had a good seal on it, you could pump out air and create a vacuum. Lighter than air means air at a lower pressure than 1 atm. If you could get it to a pressure of -7 psi, you might recieve somee bouyancy, there. Evacuating the air pressure would be brilliant. So flip the pump to deflate and pump that air out. You would need a one way valve flipped in reverse to achieve that and bouyancy would be increased withiut needing to fill with air. Aside from the raft now having less weight because of the weight of air, its macro density would decrease. The voids would i increase in bouyancy. If it was a very poweful vacuum, an elephant could not sink those pipes. Dont forget to have multiple chambers , on case a seal breaks. That chamber would take on water very fast. So this set up would require decent seals and many chambers, preferred. In order to put a lighter than air gas in those pipes, you would have to evacuate some air in them, creating a vacuum. At that point, o adding of any gas would be heavier than the vacuum, itself. Sense the walls are rigid. I love the idea but helium would juat be heavier to add in there after creating a vacuum to add any other gases.
So good beautiful 👍😂
Can you do more step by step instructions on how to do your builds so we can follow along?
ඔයාගේ නිර්මාණ ගොඩක් හොඳයි
Hi I am from Dhaka, Bangladesh.
Very nice your creation.
*Waiting for build the passenger solar electric car at home part-2*
Same man
Ya
Yes I will check every day
Yes
I also waiting
Wow amazing👍👍👍👍
You should attach two pontoons under the boat. With 45 degree angles. Would give you more bouyancy and less resistance. Might hydroplane.
😊
Ide yang sangat bagus..MANTAP 👍👍
That was pretty damn cool I’ll give him that
Good job...👍👍👍
Поехал в соседнюю деревню на дискотеку, со своей фонотекой
Woooow bravo👏👏👏👏👏👏👏
Why am I glad that 775 motor isn’t in the title
Hahaha
yes a im from indonesia
sx ruclips.net/video/6_2FmtsOiE4/видео.html
Better know how to swim on that little boat
Excelente creatividad,amigo😊😊😊😊
Waiting for solar car part 2
Kreatif, inovatif dan meng inspiratif sekali..
Kereeenn..
😎😎👍👍🙏
Я понял почему у него всё получается, всё нужно делать босиком ))
Awesome 👍😎 just got to put a plastic sheet wrap it will be the best
Pretty cool. Curious, what would the cost be on this project? Did you by chance have a ballpark figure? Like others have said, pvc used to be cheap. Not no more. Great build
12" x 20 ft Schedule 40 PVC isn't that expensive. I posted a link to it but they took down the link. I haven't found the giant styrofoam blocks yet
Excellent ! Now I want to build one!
Very good work. And it didn't sink!👍
Good
Im seeing the beginning of a long tail boat with the 2 stroke engine....
Excellent project
Hi I'm from South African just want to know what happened to the Solar car. Because the car looks so cool and love the shape
Dude its only been a week, this is one guy
do you know Lesotho I am from there
Wow nice is good 👍👍👍👏👏👏👏👏👏
Hey man, I like your stuff I would like to get the plans for the car you build a few months ago... Thanks🙂
Amazing, you are GREAT man👏🏻👏🏻👏🏻
Yes, very simple and practical.
Could use polyurethane to fill up the pipes, aluminium screws and marine ply and a sheet of polythene to cover up the Styrofoam.
By the way, which size of pipes is he using 4" or 6" ?
Also, I wish I was able to source a 2- stroke boat engine locally.
8"
👋👋👋 Bravo 👍 nice
I would have made it 1 foot wider and 2 feet longer. Afterwards I'd wish I had made it 2 feet wider and 4 feet longer. Only to regret not making it 4 feet wider and 8 feet longer. It never ends.
PVC Queen Mary?
ruclips.net/user/NewOneMedia2017
complete boat making video with fiber glass materiel
watch and subscribe channel.