TOP SECRET LG Dishwasher Service Test Mode
HTML-код
- Опубликовано: 23 июл 2024
- Step-by-step instructions on how to enter and run through the service test mode on an LG dishwasher. This service mode will help you troubleshoot and diagnose problems with the dishwasher. The dishwasher shown in this video is model LDF5545ST/00 but the instructions in the video apply to many different models of LG dishwashers.
Table of Contents:
0:00 - Intro
0:21 - What Test Mode Does
0:45 - How to Enter Test Mode
0:54 - Test #1: Detergent Dispenser
1:20 - Test #2: Door Vent Blower Motor
1:55 - Test #3: Soil Sensor
2:14 - Test #4: Drain Motor
2:38 - Test #5: Water Inlet Valve
3:19 - Test #6: Washing Motor
3:47 - Test #7: Vario Valve
4:21 - How to Exit Test Mode
4:27 - Where to Buy Parts & Locate Model Tag
4:40 - Outro
How to Replace Detergent Dispenser: • How to test & replace ...
How to Replace Door Vent Blower Motor: • How to replace LG dish...
Dishwasher shown in video: LDF5545ST/00
Appliances break, but repair & maintenance doesn't need to be difficult. Find the right part for your job at partsdr.com/
We sell new OEM appliance parts for Whirlpool, Maytag, Kenmore, Amana, Estate, Roper, Frigidaire, Electrolux, Tappan, Westinghouse, Kitchen Aid, Jenn Air, Bosch, LG, Samsung, and more.
If you found this video helpful, please click the thumbs up button and leave us a comment below.
Connect With Us:
Facebook: / partsdr
Twitter: / parts_dr
Repair Forum: forum.partsdr.com/
Blog: partsdr.com/blog/
Subscribe to our RUclips channel: / @partsdr
#PartsDr #MakeAppliancesGreatAgain #LG Хобби
This is gold. THANK YOU.
Dude, great video. Precise, informative, and no drama.
Liked and Subscribed!
Thank you!!!
Thank you for this valuable information, you sir just saved me lots of time and $$, narrowed down to the variable motor. THANK YOU!!!
Nice job!!! That is a lot cheaper than a new dishwasher!
For Tony R.: Sounds like the electronic control panel located at the top of the door. It costs about $200. Had the same issue last year. Something to do with moisture from inside the dishwasher affecting the board. I hear the replacement parts have added extra protection (better board sealant?). It has been a year since I replaced it and so far, so good.
My control panel cracked right at the power button about a week after installation, and it was letting in crazy amounts of moisture. Despite that, the panel lasted 4 years before it started acting up. Bought a replacement for 200 and it's new again!
Great video! Thank you 😌
Thanks! 🙂
I was sure my dryer fan was noisy (sounded like a cat purring). This confirmed it. Thanks.
Great! Thanks for sharing! We have a video on replacing the blower fan here: ruclips.net/video/2-79GE59GJA/видео.html
You didn't address my problem but you fixed it just the same! Couldn't get rid of the "CL" (Control Lock) despite following all prescribed solutions, including turning the breaker off for awhile. I ran your tests and the CL disappeared and it started right up. Many Thanks! (LG Model LDT7808BD)
Thanks for sharing! I bet someone else will find this helpful.
excellent tutorial
Thanks!
Thank you for this video!
You're welcome!
Hi
This is very informative.
I have question thought, can we test rinse aid dispenser with service test mode?
My LG dishwasher LDF 7561ST has a start delay feature but it doesn’t allow a delay selection more than 19h.
The user manual says the delay can be set up to 24h. I have turned off the braker for 10 sec, twice, but, whatever the programme chosen, the delay limit is still 19h, with a incrementation of 1h at each push. There are no error code.
What could be wrong?
Great video, thanks.
You're welcome!
Great video worked perfect
Great! We are glad you found it helpful!
Thanks! Allowed me to isolate the part making the noise!
Great to hear! Which part was the culprit? Thank you for supporting our channel!
Hi, I just found your video and thought it was very well done. Maybe I missed something but how do I know which test is being run. I have the model you demonstrated on which fails mid cycle about 122minutes remaining with no error message, then it just switches off.
THE BEST! FIXED IT. Thank you so much!!!!
That's great! What kind of problem were you having?
@@PartsDr It wouldn't start. Looked at other tutorials which did not help. We pressed power and start and then it ran through the dignostics and when it was finished...the dishwasher started and was fine. YAY
I have Model#LDF5545BD. I Tried the 1st test mode on the detergent latch, didn't work and I couldn't even get to 2nd test mode. I think this model has issues with the det. latch, door latch. When I called LG there was a recall on the control panel?? LG said to send a tech out there is a $125 trip and Diagnostic fee!! I was just hoping I could get through the test modes 1st before spending $ on this New Appliance!! Any suggestions?
Hello great video
very informational and helpful, this is the exact model that I have and just got a month ago and I am having trouble with an AE code.
Me too! Mine is only 1 year and 3 months old
@@hdear8455 MIne 3, only 2 years old. So tired of these things not working very long no matter if they are cheap or expensive.
Same
How to scroll through to drain 04 code.
Got a LDF567 with a 9E code blinking, unknown what it is, seems the motor under keeps running though... any ideas, cant run diagnostics
Great help thanks
You're welcome!
Your the guy ,Thank you
You're welcome!
My Kenmore made by Lg is shutting off with an HE code 36 minutes into a cycle.It is model # 722.14673710.I tried your lg dishwasher test mode and I cannot get past step 4.When I press start to move to step 5,it stays in step 4 and continues cycling test 4.The first 3 test move thru fine.However,the board does not show me 01,02,or any numbers corresponding to test mode levels.Any help would be greatly appreciated.Your other how to videos are easy to understand.Thank you for that.
Liked and subscribed !!! Aswsome thank you!!!!!!
You're welcome!!
I set my model LDF8874ST LG dishwasher to a quick wash mode and I ran a couple of errands. When I got home, the AE code was flashing, there was a little water in the floor and I tried to power off, and the power went off and then came back on and continued to flash. When I opened the door, I could hear the drain pump. I tried again several times to turn the power off, and it kept coming back on, pump running, so I unplugged it under the sink. I have watched your video (and a couple more) and it looks like it could be one of several problems, from the fan assembly to the door gasket, to the spray arm. None are obvious under inspection, so I suppose either 1. I'll have to tackle the job (I am 70 yrs old and my husband is not well). Or call an appliance repair. The ladder not being optimal. We also have an LG refrigerator that had to be serviced and finding someone to service LG was very difficult in my area. Finally, one came from many miles away, charged me almost $1000 and broke a freezer drawer glide and didn't bother telling me. I found it some time later, and it's been impossible to get the part. I also have an LG range. I will not buy LG again, even though I loved the dishwasher when it was working. Very frustrating.
I just had the exact same issue and can’t get it fixed. I got the dishwasher brand new and it’s never worked for me. I’ve had so many issues with it from the beginning.
I'm getting an NE error code. I replaced the vario motor and a couple relays related to it, no help. I just tried running the vario motor test while the vario motor was hanging loose (I pulled it out to see if it was working during the year), and the vario motor was turning gradually during the test. I manually triggered the relay sitting next to the vario motor bracket and confirmed the test will advance to "lo.' Should there be a cam attached to the vario motor shaft ? I don't have one Bd wondering if that is why the ne code persists.
Hi.
My dishwasher is LD-12BW8. It shows error 0E but drains the water out and it seems to be continuously trying to drain. Hose is not clogged and I don't see any debris in the pump area. Can anyone please advise ?
Thanks.
Would you know the button combination for test mode on a LDS5540ST? There is no “Start” button on the panel. I’m getting an HE error at the end of the wash. Heater element is new so try to figure out what else to check
Mine overflowed with soap cause I put dish soap in it and now it has a red blinking light in the front and has a blinking error code AE how do I fix that? I already tried reseting it and even if I turn it off it turns back on beeping do you know why this would be?
My problem with the DW it shuts down after running a minute. So I ran the test and When I run test #6 it shuts the DW off. What are your thoughts?
What’s the AE error code can you run test during that time?
Thank you for an awesome video. When I get to test 7 I get a C56 and 1 LO code. Never gets the upper arm code. I confirmed the vario valve and microswitch are good. Would you suspect the controller board?
Usually you have to narrow down the problem like you are doing by process of elimination. You could also check the wiring between the parts and the control board.
Hi Ryan. I keep getting an nE code when I run test #2. What is this trying to tell me?
Plz tell my lg dishwasher modle DFB 512Fw and it is not restart from the same time where it is power off its restart from start of the cycle
I have been having issues where the dishwasher won’t turn on. I have to kick the breaker for a couple min and then it will work. Then after a couple times got an LE code, reset then get an IE. now when I do the test mode I can’t get anything to work. I am assuming it’s a control board at this time. Any thoughts?
Thanks for the information. This is very helpful. My dishwasher doesnot clean upper rack. The nozzle and spray arm looks ok. In my case, test #7 4:06, there was no error code . It show 1 UN and 1Lo but there was no water sprayed from upper or lower arm during test mode. Is it normal in test mode ?. What could be the issue ?
Possibly a bad diverter motor? We would start by inspecting the motor and the pieces that the diverter motor moves.
Great video! I’m getting a (- - -) code when I went to run a load. It will not take any commands. Any help would be appreciated.
Excellent
Happy to help!
*Great Video Thank You!*
You're welcome!
Awesome, will give this a shot. Have this same model and it just recently started shutting off randomly after a few minutes of starting a cycle. No error codes, it'll just power down, then power back up. The other day, all of the lights on the display turned on at once. Not sure what any of it means. It's only about 1.5 years old and for the prices, it's pretty ridiculous that we're already having issues with it.
We have same issue now. Have you figured out what is causing this problem ?
@@Virsavia77 No, haven't had a chance to go through these steps. Was going to give the "smart diagnosis " a try sometime next week. You call into customer support, push some buttons on the washer then place the phone near the washer and the customer service rep is supposed to be able to tell you what's wrong with it.
@@TROD760 thank you for respond. We will do smart diagnostic too because regular diagnostic didn't help. The dishwasher turned off during diagnostic and we don't understand why.
sounds like the control panel, easy to replace and it's under warranty by LG for 3 years so don't delay contacting them
Mine too!
Nice info
Quick question I tried to put my lg dishwasher same model in diagnostic mode and it shut off rt after the wash motor test won’t go to 1lo .. also dishwasher shuts off 25 mins into the cycle
That could indicate that something in the vario valve system isn't working properly. It would be a good place to start your troubleshooting.
Great video to get me started with troubleshooting.
OE error code, not draining properly. I have checked the drain line, it is free and clear (back-blowed with air). Tub filter is removed. No air gap device installed. Ran my fingers in the drain basin but didn't feel any debri. When running through test mode, the drain motor runs, but no water drains (it hisses air lightly instead)
Advice?? TIA 👍
Have you checked the garbage disposal? ruclips.net/video/ws9tMUq4MY0/видео.html
Hi I have a LG dishwasher and it keeps popping up error code BE and I checked the leveling and also ran milk just like it said to and then had a plumber look at the leveling part and he said its leveled. Idk what else to do?. I turned on and off main breaker to dishwasher and still error code BE again. Idk what else to do. Please help.
Hi there, I have LG dishwasher model LDP6797ST. All of sudden it stopped working. It has power but does not show on the touch pad buttons and not working. Can anyone help.
Not sure if anyone can help but if so I have an lg and when I press the power button I get an L2 and can’t do anything else I’m not sure what to do if anything can help I would appreciate it.
This video has helped me immensely in troubleshooting my dishwasher. I have an LG LDF5678BD. The washer motor is very loud and I plan to replace this. The other message I see is when I run the Vario test I see the 1 LO followed by a C93. The display will flash alternately between 1 LO and C93. Any thoughts on this?
Sorry, we do not have anything on the C93. If you find out anything, please let us know.
do you know how to put LG LDF9932ST into test mode
Thanks for this video. We have an lds5540st that is not turning on at all.Because of cover issues, I'd like to try to diagnose and fix myself. Have heard could be door latch or controller or thermal fuse or....? But it is unclear to me how to locate and diagnose these parts and issues. Thanks for any help!
"covid" issues, not cover
Hi Andrew, see page 38 for troubleshooting steps drive.google.com/file/d/1uKAtivuLWSzNRw-1nZpO6mp95ALjosb4/view?usp=sharing
We have a LDF5545ss that’s giving the ie code. I have a water inlet valve order but I can see the water inside the water inlet guide when it’s filling and the bowl fills then a 30 seconds later it flashes the ie code. Any thoughts?
Most commonly a bad water inlet valve or a bad water inlet guide. Also, make sure to check the water supply to the dishwasher to make sure you have adequate water flow. We have a video on testing the water inlet valve here: ruclips.net/video/vrDSl24vwao/видео.html
What is the code to skip to the last 5 minutes or end cycle? I saw an engineer do that in order to check if the dishwasher was completing the last cycle successfully. Also is there a way to only do test 7 for example, or do we have to go through all of them?
We just purchased a new LG dishwasher (11/14/20), and it stopped draining twice; we had to do a manuel drain. It's super quiet. Any ideas about what could be going wrong?
When the dishwasher isn't draining, try running it through test #4 in the video. This should help you narrow down if the drain pump is running or not and help you narrow down the problem.
This video was great! I think my dishwasher is in a service test mode. The display is cycling through these 3 codes: n04 d32 U40 and all of the lights are solid (including the red, white and green lights on the front) but I can’t exit. Start and Cancel don’t work, the power button just double beeps and none of the other buttons work. Any idea how to exit or restart? The machine ran a full cycle yesterday, with no issues. Thanks! 😊
Sometimes we have seen a bad control panel cause these types of symptoms. Let us know what you find. We have a video on replacing that type of part here: ruclips.net/video/czeYpx62Dv0/видео.html
Thanks!!!
You're welcome!!
@@PartsDr bro, it was just clear information, without any unnecessary stuff.
Nice video! My daughter's dishwasher (LDFN4542S) required the Start, Power, and Auto. Her dishwasher has been beeping then powering down usually within a couple minutes but sometimes 15 min into cycle. The Smart Diagnosis comes back good and all the tests appear good with one oddity. The final test is supposed to test spray arms 1un, 1lo, and then 0lo. The 1st test it went straight to 1lo so I retried the test and then it went through all 3 . When I showed my daughter how to do it then it reverted back to testing only 1lo. Is this normal or does it indicate a problem?
As long as it is switching between the upper and lower spray arms then that test should be okay. It could be a bad control panel where it is pressing buttons on its own and causing it to stop running. Let us know what you find. ruclips.net/video/czeYpx62Dv0/видео.html
Did this and the soap dispenser did not open. How do i fix it?
Looking for video to change a cracked steam inlet hose. The preformed hose. LG model LDT7808ST
Also how to scroll to a specific code. Drain 04 to get rid of water.
My dishwasher still washes great but the drive motor makes noise while it’s running. It has a 10 year warranty. The service tech told me that it might continue to run for a year or more versus buying a new dishwasher or replacing the motor. I’d like to get your opinion on that. Great channel I subscribed.
Hi Rick, if the circulcation pump motor is noisy while running it is usually a sign that it is failing. In some cases a noisy pump can start to leak, so it is something to keep a close eye on. If it is under warranty, you should see if they will replace it for you.
Thanks
You're welcome!
Excellent, I'm trying to figure out how to do this with a LDF7774ST.
Page 11 here: www.scribd.com/document/318999575/LDF7774-Svc
Anyway to run this for LG DF455HSS?
I’ve got an LG LDT5678ST dishwasher. When I hit the power and start together nothing happens. I was wondering if I need to hit two other buttons to cycle through. Thank you for your videos, they are very helpful. LG direct drive dishwasher
I'm sorry but we do not have information on the service mode for your model dishwasher. If you locate it, please share it with us.
@@PartsDr On this model, pressing the "Power" and "High Temp" buttons together will engage the test mode.
On this model, pressing the "Power" and "High Temp" buttons together will engage the test mode.
In the video you refer to test 6 as "wash motor", but I don't see a part specifically called this on your parts page. Is this the same as the "circulation pump"? My washer is throwing code LE.
The "wash motor" is the same as the circulation pump.
Do you know how can I signature a program ?
For the LDFN454 model i had to hold START, then AUTO, then POWER to go into test mode.
Thanks for sharing!
I have this exact model and it has been giving me an E1 error on a normal cycle after starting to fill with water. Repair company has replaced water inlet valve and control panel without any fix. They even replaced the sump assembly which seemed unrelated. Tried running through these tests and Test #5 is where I see the issue. There is water filling into the unit but there is no “frequency” reading on the display (I.e. stays at 000). Any thoughts?
I’m assuming the dishwasher is successfully sending a signal to fill with water it’s just not reading and water going in. Therefore it thinks it is leaking all the water.
You may have a bad flow meter in the water guide assembly. You can view this part on our site here: partsdr.com/part/aec74337401-water-inlet-guide-assembly Please verify the part is correct by entering your model number on our site.
I'm having the exact same issue. It's not filling a lot during the test but water is coming out. Were you able to fix this Michael?
I have this same model. But when I get to test 7 it only displays "LO" not 1un or 1lo nor.dpes it display an error code even though the pressure is weak in the lower arm and the arm does not spin or push water up to the top sprayer.
Any thoughts?
Only one spray arm operates at a time. The diverter motor is what diverts the water to either the upper or lower spray arms.
I just replaced the main board. HV Connections cooked. Seemed to work. Then stopped to click,
after I left. It just clicks doesn’t seem to advance or anything I’m gonna go back and see why tomorrow. If anyone has any ideas 🙂 I’ll be happy to hear them
I cant get my Ldp6797st Dishwasher to enter self test mode. Its not starting. Just the buttons on the left work, nothing on the right. Start dosent seem to do anything. Please help!
We don't have instructions for the test mode for your model currently. The description of the problem sounds like a bad touchpad on the control panel.
We noticed that on Normal setting that 3/4 of the time when its 36 min left it starts beeping alot. I would have to press start a few times to bypass, filter is clean and I ran a diagnostic with LG app and it says all good. Can someone let me know if I should check something else?
Did you find the issue?
I can’t open the door to my lg dishwasher; It’s stuck or a lock is on. I called Lg and was told to cut the power to the dishwasher off so that it could reset itself but that didn’t work. They referred the job to a contractor in my area but they don’t work on warranty products, idk. Please help. Thanks
I have the ldf5545ss model. I have changed the noise filter thrice already. On each change, the dishwasher starts working and goes off midway. and the Noise filter goes bad too. What coulkd be the cause? I have used other appliances on the power socket and they work fine.
It could be some component on the dishwasher that is bad and drawing high current causing the fuse on the noise filter to blow.
@@PartsDr such as which part?
@@jibonjo That is something that you or a technician would need to troubleshoot.
I have a MEZ64589015 that always has the * flashing on the the front of the machine, I filled the reservoir and still it’s flashing and will not start, seems like it is stuck in standby. I’ve reset the breaker and pulled the plug and still it’s locked in standby mode, any thoughts? Also loved your video.
Mines too! Is it the panel?
Mine does the same. Light flashes but it doesn't start or run. Only about a year old, not used very often. I wouldn't think it should be having issues already!
Need information about the CL code
Great video.
My dishwasher looks like the same model but will not enter test mode, any ideas?
Model number XD4B24PS.
It looks like this model is from Australia. Unfortunately, we do not have any service information on this model.
Power button and high temp at the same time
I have the exact same model. My washer just power's off any idea?
Hello, I have an LG LDP6810SS, and the Power + Start buttons don't do anything. Any idea if it's another button combination?
I'm sorry, we do not have information on that model.
@@PartsDr ok, thanks anyway - was curious how to get it into the diag mode and then how to get through the tests because the buttons/screen aren't visible when the door is closed
Power button and high temp at the same time works for some models. Try that
@Parts Dr, I engaged the test mode on my LDT5678ST because it has stopped sending water to the sprayers. Upon activating test mode, the display showed n04, d49, and U50. I then pressed Start. When the machine reached test number 7, the display showed C00 then 1LO with loud motor noise but no spraying either top or bottom. All other functions appear normal. Any ideas? Thanks very much!
When I engage my test mode, I get n04, d49, and U50 in the display. My test sequence differs slightly from the one you have listed.
1) Detergent door
2) Sump temp
3) Door vent blower motor
4) ?Soil sensor? Display shows "180"
5) Drain valve/motor : Good
6) Water inlet valve/motor: Good
7) Washer motor: Loud motor noise while spinning. No water to either upper or lower sprayer.
I appreciate any help you can give. Thanks!
It could be caused by a bad circulation pump. If the pump motor is receiving power but it isn't running, either the pump is bad or something is jammed inside of it causing it not to turn. This is the circulation pump for your model here: partsdr.com/part/abt72989206-pump-and-casing-assembly?model=LDT5678ST---00
How did you get yours into test mode? Mine won’t activate. Have the ldts5552s which is very similar to yours.
I have the same dishwasher but can't get into the test mode. Can you help please?
@@bmanizzal4319 power +high temp is how I got mine to go into test mode.
I tried all of these tips and the only thing I noticed was that the 1 un did not appear, it went straight to the Lo. When I first start my washer it will run for a couple of minutes and then the entire display starts flashing and it shuts down.
Could you please send the service manual of this dishwasher. While doing vario test my dishwasher shows C43.My dishwasher is LDF5545ST
We couldn't find LG listing anything about C43 for your dishwasher.
Thanks for your help
I have model ldt7808st on the final test the mode goes from 1 lo to c 56 happen to know what this means?
I'm sorry we do not. If you find out please let us know.
Cody - did you figure this out a couple years ago??
@@PartsDr do you have any updates on this particular problem during test mode??
after entering the test mode all the light are illumined but nothing happens when pressing the start button Model # LDF5545ST
I have a suction noise from the circulation pump wich does not have enough water in the tub. Anyway to fix this? I have the same model. my water valve is open all the way under my sink. Thanks
Possibly a bad water inlet valve not letting enough water in or a bad water inlet guide that is not measuring properly how much water is entering the dishwasher.
Thank you, it's still under one year waranty and does it since day one. I will have it check. Problem is probably what you say, because if I manualy add water during washing cycle the noise stops. Everything else tests fine.
@@vincentcantin6945 Sounds good. Let us know what you find when you have it repaired.
My LG dishwasher gives bE error code but no bubbles and unit is level. Any ideas?
I’m also getting the bE code. It’s level and no bubbles. Did you figure out the problem?
The control panel on my LG frequently flashes OFF then back ON quickly, and there is associated beeping noise. I’ve tested the power and it’s good, could this be a bad panel?
Yes, that problem could be caused by a bad control panel.
I have the same issue. Has yours resolved?
Does the test mode check any steam, or heating elements?
I had the same question
So if the door is locked how do I open it?
We had the LE code pop up when we tried starting a load of dishes. I ran through this test and when I got to test 5 for the water inlet it struggled for a bit and then threw the LE code at me again and ended the test. Would this confirm that the LE code is being thrown because of the water inlet? Like is it safe to assume that’s the case so I can narrow down which part to replace?
The LE error code is a motor error. This is usually a problem with the circulation pump motor.
@@PartsDr okay thank you. Hopefully I won’t fix the circulation pump motor and still have the inlet valve to worry about. Inlet valve seemed doable for me but not the pump motor. Might end up calling LG to come fix it but they charge flat rate $299 😭
My proble is on test #7. The uper wash arm does not work. What can i do to fix it ?
First check the diverter motor.
I have an LG Dishwasher model # LDF7774ST. Recently it has started to start running by itself when the door is closed. Can you let me know what is wrong and what needs to be replaced?
Thank you!
We often see a bad control panel cause these types of symptoms. partsdr.com/part/agm74051507-control-panel-assembly?model=LDF7774ST
Thank you so much! Just ordered the part.@@PartsDr
Can you please tell me what is the problem
My LG dishwasher plays no more tones when I press a button, when cycle starts, or when cycle ends. Why??
On the model dishwasher shown in the video to activate or deactivate the button sounds, press and hold Dual Zone and Energy Saversimultaneously for three seconds. The error alert sound cannot be turned off. Check the owners manual for instructions for your specific model if the instructions above don't work.
I have a 8 months old LG Dishwasher that keeps getting an IE error every two months or so. The technician has been onsite to replace the water inlet valve 3 times and so I have asked LG to take this dishwasher back since they don't seem to be able to fix this issue. After this experience I will never buy an LG appliance ever again!
I too have similar IE proble.
I have a ldf5545st LG dishwasher. The last step it just shows “LO” and continues to run. What would be wrong with it?
Check the diverter motor that is used to change the water between the spray arms.
Mine also only displayed LO during the test, but I ran a turbo cycle and I put a camera in there and saw both the top and bottom arms spin
How do you fix the soap door? Anyone have any suggestions?
If the soap door is broken, the entire dispenser will need to be replaced as none of the components of the dispenser are sold separately. We have a video on replacing the dispenser here: ruclips.net/video/NrhtWLH3XdQ/видео.html
I have pressed the power and start buttons at the same time and it does not start the test. An LG technician taught another way but I didn’t write it down. Is there anyone here that can give me that other way to do the test? Thank you kindly in advance.
Same. Nothing happens and my error code is FF which isn't listed anywhere for a dishwasher, only for a fridge 😮
Fails test #7
Does this imply pulling the unit out or can the motor be checked for an obstruction in place?
Flagging an LE code
For the LE error code, this is what LG says to check:
1) Wiring connection is OK? (Washing Motor and Controller). Check and reconnect the wire.
2) The Impeller of Washing Pump is locked. Replace the Pump Casing assembly.
3) Is the Washing Motor is OK? Check the electric resistance of Washing Motor.
4) The Controller is troubled. Replace the Controller.
Great useful video!
I'm a maintenance tech jack-of-all-trades and running into all kinds of different appliances brand issues.
Currently the LG at my home powered down, I vacuum the water out of the sump and power was restored what could be the cause? I'm thinking potential restricted drain?
My LDF5678ST keeps tripping breaker. Diagnosis comes out fine. Can’t run test mode. Where should I start the trouble shooting? I’m thinking main board?
Start by checking the electrical connections inside the electrical box where the power supply comes into the dishwasher. See this video here: ruclips.net/video/JBoXTLpLxwU/видео.html
@@PartsDr so I was able to run test and it doesn’t let it run third test. That is the drain pump right? Also disconnected pump power and still tripped breaker. Assuming main board?
@@ajguerra9547 It could be a bad main control board. This type of problem is difficult to troubleshoot.
Having same issue again. Last time I put a high loop and it worked. The dishwasher keeps tripping breaker on test 4. Swapped out drain motor and still tripping.
Our Dishwasher door does not want to open after finishing cycle. Help!
Maybe it is a bad door latch? ruclips.net/video/Q5aCvWzOb50/видео.html
Is there no test for the heating element? My dishwasher is running the he code after I fixed the fe error code
We recommend to test the heating elements resistance using an ohm meter. It should measure approximately 11.5 Ohms at room temperature. Make sure the power is disconnected from the dishwasher and the wires are removed from the element when testing.
@@PartsDr ill try that thank you
Can you help me out? When I run test #6 I get an awful grinding/bad bearing sound. I just replaced the the motor pump. So that didn't fix it. Is it the diverter motor that's making the noise? Wish i saw this video sooner... thanks for your help.
It also threw an LE code. Which was motor failure
What is the model number of the dishwasher and which part number did you replace?
@@PartsDr
model# LG LDT7808BM
ABT72989205
PUMP CASING ASSY
When I pulled the old motor pump it smelled (burnt electrical). This noise has been going on for a couple weeks and thought that was the fix. No longer have the LE code but the grinding/ rubbing noise.
@@nsext3330 What was the problem with the original pump motor? Did it make the same grinding noise?
My chime stopped working. How would I turn it back on for this model
To activate or deactivate the button sounds, press and hold Dual Zone and Energy Saversimultaneously for three seconds. The error alert sound cannot be turned off.
@@PartsDr Thanks that worked.