I'm chewing on a toothpick bc I have some type of anxiety where I pluck my beard out and I don't even notice when I start doing it, so chewing a toothpick has helped reducing that anxiety thus leaving my beard grow
Don’t sweat it man. In fact, this long format install video saved me on my install. I could NOT make sense of how it married up to the transmission and you cleared it up. Thank you thank you. You got the lil “Juggy” up and running. (Photo on the Reddit page)
Yeah mine took a while too and I ordered a couple pinions because I wasn’t sure what would work and only 2 have shown up so far, luckily the HotRacing one worked 👍🏻
Bro I love the humbleness of this video & the nice light humor. I'm hitting that bell now & hope whatever misfortune you have at the moment SURPASSes you in the near future. Nothing but good vibes, & blessings your way all the way from guam 🇬🇺 & California 🤙🏾🙏🏾🙌🏾👍🏾
I will post more pics on reddit so you can reference the layout of all your electronics Great to see your spirits up considering all that has gone on on your side. keep RCing. love the video.
That lock nut on the that new big gear stays loose or at least they are on the the stock gears. If you snug it down it rubs or binds. May be your issue. How it was when putting motors on my deadbolts.
I took it back apart because of the noise and yes it was a bit too snug but also the gear itself was a little messed up so I replaced it with the other one I ordered, I got 2 of them since I had 2 surpass motors and the second was perfect, now it’s a crawling machine! 🤘🏼😎
Sweet . trying to watch all your content to some how help you . Ive been in my own situation this month RUclips help take the mind off things . enjoyed the video alot keep spirit's up.
I recently purchased the same motor and mount but need the screws to mount it. What size are they and where can I find them? Please help. It will be greatly appreciated
I’m not sure what it was, after I switched out the stock ESC for the surpass motor and dumborc receiver it stock locking up, I think it’s just the stock ESC/receiver combo
@@UpperLeftRC Well.... I figured it out. I was running the lizard through the stock setup but I ended up figuring out what the problem was. The battery needed to wired in parallel so that the stock esc could get power for the servo and the furitek could get power for the motor.
Noo the wire. I think I was able to figure out that it comes with the lizard. But I have another question for you you have the hot racing 11t pinion gear so I can not find that same one right now. But I’m wondering if a 0.5m 0.5mod 3mm 12t brass pinion will work on it? With out damaging or ruining the spur gear?
Just ate tacobell during the first video 😂😂 i hope your comment about charging lipos in the window wasnt foreshadowing. Jk. Hope everything turns out okay. Just seems just other day you was at 3xx subscribers. 👍
Haha I didn’t even think about the foreshadowing lol but yeah it should all turn out great and It really is crazy how quick the channel has grown! I appreciate everyone’s support including yours 😄👍🏻
It’s the “HotRacing Metal pinion” I got it on eBay, I don’t have a link for it but if you look up scx24 hot racing metal pinion it should be pretty easy to find 😄🤘🏼
Not that it's the end of the world or anything but gears are measured in teeth not turns. Also for anyone else doing a conversion like this pay attention to your gears. Notice in this video how bad it sounds and he talks about the binding. It's because the incorrect gears were used. The pinion used was a 48 pitch and not the required mod .5 that matches the spur gear.
I'm chewing on a toothpick bc I have some type of anxiety where I pluck my beard out and I don't even notice when I start doing it, so chewing a toothpick has helped reducing that anxiety thus leaving my beard grow
Don’t sweat it man. In fact, this long format install video saved me on my install. I could NOT make sense of how it married up to the transmission and you cleared it up. Thank you thank you. You got the lil “Juggy” up and running. (Photo on the Reddit page)
Glad I could help and thank you for posting it on the Reddit page, I love seeing everyone’s projects! 🤘🏼😄
Been waiting for what feels like a life time for my pinion, and motor mount to show up.
Yeah mine took a while too and I ordered a couple pinions because I wasn’t sure what would work and only 2 have shown up so far, luckily the HotRacing one worked 👍🏻
I ended up tearing stuff apart til I found a gear that worked😆. My brass ones showed up today finally but the plastic one I made is still holding up.
Stay positive and continue doing what you're doing. Thank you for setting such a great example for others to follow.
Bro I love the humbleness of this video & the nice light humor. I'm hitting that bell now & hope whatever misfortune you have at the moment SURPASSes you in the near future. Nothing but good vibes, & blessings your way all the way from guam 🇬🇺 & California 🤙🏾🙏🏾🙌🏾👍🏾
I really appreciate that! it’s people like you make my day 😄👍🏻 also I love the “surpass” pun! Good vibes all around 🙌🏻
Noice
You will have a blast that motor is awesome I but 1 in my deadbolt but now the furitex lizard is acting up it will not even turn on
Happy you can still post.
I’m lookin at getting the sidewinder micro from castle.
Woohoo, I know your happy! Still just looking at mine... I got a small 12tooth and the smallest I could find from HR was a 15t. Need to get building!
Heck yeah! The longer you put it off the less brushless crawling you can do lol 🤘🏼😄
I see this in my future 😂. No TBell for me but I did have 🌮 yesterday. Great video. Congrats on 1000 subs!
🎉😄👍🏻
1k! Congrats! And don't worry, as long as you have fun filming we'll have fun watching
🙌🏻😄👍🏻🎉
Turn the skid plate and motor around plenty of room for the motor. It works for my c10. Flip your pinion
Congrats 1k subscriber,nice video😻👌
Thanks 🎉😄
Take a dremel and make a little divot in the frame where the motor touches. I should have the tiny outrunner by Thursday
Your video was very helpful thanks for making it.
I will post more pics on reddit so you can reference the layout of all your electronics Great to see your spirits up considering all that has gone on on your side. keep RCing. love the video.
Thanks bud! I really appreciate that 😄👍🏻
Also, I just did my own tutorial on putting in a new steering servo and the stupid video is over a half hour long😳 so your video is all good man.
SIR tools that's what I use too I love them so much I have a set at home and at work
Congratulations on thousand subs! & many more to come!
🎉😄👍🏻🙌🏻
Good quality video! Was good
HAD Taco Bell leftovers from last night, now I'm building my system along with you.
🤘🏼😄 heck yeah
It was meant to be that I stumbled across your video to install this motor lol. The Taco Bell thing was just the Gods saying watch this one lmao
Great setup! I love mine
Congratulations for 1k subscribers!!!!
🎉😄👍🏻
Make sure the pinion little screw is not touching the spur!! I also made it and that jumps comes from that!
Thanks for the heads up
I always loved watching and I’m learning a lot from you🙂😇☺️
That lock nut on the that new big gear stays loose or at least they are on the the stock gears. If you snug it down it rubs or binds. May be your issue. How it was when putting motors on my deadbolts.
I took it back apart because of the noise and yes it was a bit too snug but also the gear itself was a little messed up so I replaced it with the other one I ordered, I got 2 of them since I had 2 surpass motors and the second was perfect, now it’s a crawling machine! 🤘🏼😎
@@UpperLeftRC great. I used the barrage motors and adapter plates. I think they are too tight of mesh. Real noisey on my deadbolts. 👍
My HR spur was so uneven i just threw it away, took a chance and got another one that worked great.
Dang sorry to hear about the first one but glad it work with the second! 🤘🏼😎
Nice gonna do this next payday, gotta gather parts….eating chips now lol
Damn. You’re blowing up from the shoe up.
Sweet . trying to watch all your content to some how help you . Ive been in my own situation this month RUclips help take the mind off things . enjoyed the video alot keep spirit's up.
Thank you I appreciate that, and I hope what you got going on gets better soon too, always keep the spirits up 😄👍🏻
crazy to be at 1k already. that happened really quick.
I agree 🤯👍🏻
Nice man 👍👍
What tools are you using? I’ve been on the hunt for a good quality 1.3mm but they’re few and far between. Those look nice.
It’s a kit I got off Amazon.com 😄👍🏻
Thanks for the vid sorry about your situation.. Well, since youre asking, Im eating a Posada steak and cheese chimichanga and spicy pork rhines.
Heck yeah! That sounds delicious 🤤 👍🏻
I recently purchased the same motor and mount but need the screws to mount it. What size are they and where can I find them? Please help. It will be greatly appreciated
I don’t know the size, I’m sorry I installed it so long ago and I just used some screws I had in my parts bin
What ended up being the problem with your furitek esc from a couple videos prior? I seem to be having the exact problem that you had.😃
I’m not sure what it was, after I switched out the stock ESC for the surpass motor and dumborc receiver it stock locking up, I think it’s just the stock ESC/receiver combo
@@UpperLeftRC Well.... I figured it out. I was running the lizard through the stock setup but I ended up figuring out what the problem was. The battery needed to wired in parallel so that the stock esc could get power for the servo and the furitek could get power for the motor.
you got a really good mic
Thanks 😄👍🏻
Where did you get the surpass adapter thingy lol
The thing to mount the surpass motor? I got it from shapeways, they specialize in 3D printed accessories 😄👍🏻
Noo the wire. I think I was able to figure out that it comes with the lizard.
But I have another question for you you have the hot racing 11t pinion gear so I can not find that same one right now. But I’m wondering if a 0.5m 0.5mod 3mm 12t brass pinion will work on it? With out damaging or ruining the spur gear?
I have a enduro 24 what weights could I get for it
I’m not sure, I haven’t looked into mods for any of the small trucks besides the scx24’s
Just ate tacobell during the first video 😂😂 i hope your comment about charging lipos in the window wasnt foreshadowing. Jk. Hope everything turns out okay. Just seems just other day you was at 3xx subscribers. 👍
Haha I didn’t even think about the foreshadowing lol but yeah it should all turn out great and It really is crazy how quick the channel has grown! I appreciate everyone’s support including yours 😄👍🏻
What pinion do you have on that? Where can I get one? Preferably Amazon. A link would be greatly appreciated.
It’s the “HotRacing Metal pinion” I got it on eBay, I don’t have a link for it but if you look up scx24 hot racing metal pinion it should be pretty easy to find 😄🤘🏼
@@UpperLeftRC thank you so much
what did you plug the motor into?
I plugged the motor into the ESC “Furitek Lizard” 👍🏻
Is that the lizard pro?
I don’t think so, this is the first version of the Lizard that came out
@@UpperLeftRC ok thank you
Not that it's the end of the world or anything but gears are measured in teeth not turns. Also for anyone else doing a conversion like this pay attention to your gears. Notice in this video how bad it sounds and he talks about the binding. It's because the incorrect gears were used. The pinion used was a 48 pitch and not the required mod .5 that matches the spur gear.
Yeah, great info and I have since gotten different gears but haven’t installed them yet, i appreciate you letting people know though, including me 😄👍🏻
😁😁👍👍
You lost me at 12 turn pinion gear.