Turn signal problem diagnosis! (turn signals not working)
HTML-код
- Опубликовано: 24 авг 2024
- Quick video reviewing 3 most common reasons why turn signals don't work, and step by step instructions on how to replace a turn signal switch on a 1998 Toyota Tacoma
Additional affiliate links to a few products I personally own and use:
Basic Hand Tools - amzn.to/2I91cBb
Drill and Impact Driver - amzn.to/2WCMxzI
Cordless Ratchet - amzn.to/2KcBsBw
Portable Jump Starter - amzn.to/2HR0V4l
Fluke Multimeter - amzn.to/2HQOx42
Code Reader - amzn.to/2HRwdI4
Upholstery Remover - amzn.to/32dXTiS
Pocket screw driver - amzn.to/2HQrPcE
Pocket Flashlight - amzn.to/3j32AVF
Hook set - amzn.to/2JUdfTi
Disclaimer:
Due to factors beyond the control of Make It Easy Mechanic, it cannot guarantee against improper use or unauthorized modifications of this information. Make It Easy Mechanic assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Make It Easy Mechanic recommends safe practices when working on vehicles and/or with tools seen or implied in this video. Due to factors beyond the control of Make It Easy Mechanic, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Make It Easy Mechanic.
sir, your step by step repair is very easy to understand even for a non-technical minded. we want more videos
Agreed...however this is one that I'm not going to attempt!
I have a Toyota Camry and I have this exact issue, exactly as you illustrated here. I’m excited to solve this problem without having to go to mechanic, I love challenging myself. Thank you very much!
Thanks for getting to the point and not yakking on about the dogs or kids and just what I needed to know!
When working on the electrical system, it's a good idea to disconnect the ground cable from the battery if possible. You may wish to use a memory back up device if you have a newer vehicle that will go wacko if you disconnect the ground battery cable. Other than that, this is a really good generalized video on the subject matter. I will install a new turn signal tomorrow on a 1988 Nissan Sentra and this helped me get my head straight on what I need to do. Thank you!
Any pos or neg will do the same
@@lacuentadevideos The negative ground battery post is where the electrons come from. This is why I disconnect that one.
@@audiophileman7047 I'm. El engineer that's why I sugest you this to easy the job.by the way
Battery is not like a water tank with electrons in it. Pushing out
It is more like a pump in a closed circuit and in a pump any side disconnected will do the same
Thanks for your simple straightforward talk and video on instructions to replace a faulty indicator switch😊
When making an instructional video for automotive repair/modification it's always a fantastic idea to clean the car first 😂😂😂
Jokes aside, thank you for this video. Not sure if it will solve my problem or not but I will know soon enough. Just wanted to clarify from my previous comment that although I cracked a joke it was out of fun rather than disrespect and that I am truly grateful that you took the time to make this video. Hoping it works for me 🙏🏼🤞🏼🙏🏼🤞🏼🙏🏼
my 98 taco got the same problem, now through ur video i got it fixed. thank u so much.
That's awesome, I'm glad to hear!
Very helpful,,,, a bit further about the tilt wheel on some cars because the wiring to the connectors from factory is to short and gets pulled loose and sometime the connectors are just poorly designed and the wires just fall out after a few years.
Thank you for the video. I ordered the part for $45.00 and replaced following your video. Thank you.
where did you find it for that price?
Check your battery terminals, mine was lose it was missing a screw and I wasn’t aware of it until my mechanic checked. He clipped the bracket and put it a new one. My blinker started working
Fast and right to the point.. Thank you for this 3 minute video!!!!!
Wow! I hunted a long time to find this answer and you nailed it.
Believe it or not, my dog chewed up my blinker stick🤣🤣 so this was very helpful! Thanks bro
Saved me a headache! Thanks!
I have a similar, but weird, issue on my Toyota truck. The left signal flashes faster than normal, but only when I push on the brake pedal. I think I have a problem with the wiring for a 4-pin trailer connector. Additionally, the brake lights on the trailer do not work when connected to only this truck (works when connected to a friend's truck).
Great video, short and sweet and to the point.
Thank you for making this video. Now I’m confident that I can do the repair myself!
Wow, I love it, my daughter had a similar issue in 1999 Toyota Camry. I can tell car a machine what to do.
Im going to be an expert mechanic by the end of this issue
I have a 2000 Solara
Both of the turn signals just stopped working, could it be a fuse ??
DUDE!!
THANK YOU SOO MUCH!!
I HAVE THE SAME ISSUE, LEFT TURN EVEN!!
My 4runner has the same issue except its iffy on the right side. This helped alot thanks!
thank you so much,this video save from getting a ticket
Thank you for the film. Can someone tell if the Turn Signals and Hazards use the same Flasher. The Turn Signals don't work at all, nut the Hazards work just fine. 2001 Saturn SL2.
Update 1: I found it!! And what it was, I removed the headliner board for re[placing the upholstery on it, and disconnected the wire to the ceiling lens. The shop manual (I fortunately have for that car 2001 Saturn SL2) advised to attach those wires w/scotch tape, so I disconnected it fm/the plug by the rear window. The plug was sitting on a thin plate, which I assumed was there for keeping the plug in correct place. After I did some research I've learned that grounding could cause Turning Signals go off. The Manual showed 2 grounding wires on the rear close to that plug. There was a clip on the plug, metal one. I disconnected the grounding there, so even w/plug in the T S-ls didn't work of course. It might be helpful for someone else. Pls check the grounding as well if you have a problem w/T Signals and the fuse is fine. I was about to replace the Steering Column Switch, and actually ordered one already (so will have a spare now, not bad thing though).
Update 2: Now everything is working w/that clip off or on, so it was not the ground connection, just a mounting clip. I'm completely lost and don't know what was the problem before. Maybe still the Steering Column Switch. The car was sitting for a long time, probably smth got corroded inside of that Switch and after several shifts back and force it is gone.
Well i noticed the front signals don't work on my 1992 toyota corolla so i went to replace the bulbs today still doing the same thing i looked still no action on the front end rear is good. I looked at the fuses they aren't bad is what made me look this up now. The left side clicks fast & the right side clicks normal. Usually fix my stuff so i can learn this simple stuff. So i'm assuming it's the turn signal switch or the relay...is there a way i can know which one it is before i get into buying random parts? Thanks for any help here & Thanks for sharing your time on here too man cool video.
I have a similar issue but whenever I put the switch to do a left turn.. It blows the fuse. Doing a right turn is fine. changed turn signal bulbs and it work fine until I went back to turn the car on a few minutes and it blew the fuse again. hazards work fine. I put a new fuse in and this time I pulled the switch slightly down to use the left turn signal and it worked fine. just only when I pull it all the way down it blows. I'm not sure what it is that could be causing this.
Thank you sir - that was a very instructive, easy to follow video. Excellent.
Thank you… resolved the issue
I have a 2004 Mitsubishi endeavor, my hazard always works, sometimes my blinker works and sometimes it won't. But when it doesn't work the left and right blinker go off. Any Idea?
I have the issue where my indicators work sometimes and sometimes not also my ac button light gets dim and when that light gets dim the indicators dont work
My blinkers work but no sound? Is it the fuses? 2006 Camry LE
Just a beautiful way to explain thanks for this saved me money
Great! I hunted a long time to find this answer on too many videos.
Great video sir short video but very helpful. You actually save my day. Thanks a lot.
So if the right dash blinker is not flashing at all could it still be the switch? I hear mine clicking, the outside lights work, right blinker does not blink with hazards. 2012 RAV4. Dash is a circuit board. Any suggestions:-)?
Your video was outstanding to change signal switch. Thanks for the video.
2005 TOYOTA RAV4 L THE HAZARD LIGHTS CAME ON BY THEMSELVES AN THEN CANT USE TURN SIGNALS SO I HAD TO PULL FUSE OUT TO STOP HAZARD LIGHTS FROM STAYING ON SO NOW I HAVE NO TURN SIGNALS WHAT DO I DO TO FIX IT? PLEASE HELP
Thank you sir , I learn a lot to you. Godbless your the Best 😀👍🏾
Hi , thank you for your video, I have a question, my 2010 Avalon when I turn signal left or right, no signal light working, but when I push hazard switch, all the light working, what do you think what the problem? Thank you
Check ur Turn signal relay and fuses
I have the same problem with my Toyota Corolla 2002. Do you resolve the problem with the Avalon?
My turning signals work you just can't see it on the dashboard so how do I fix that
I installed LED bulbs in my tail lights and of course my blinkers sped which didn't bother me. But after a few weeks the left signal noise stopped intermittently clicking and just went to a solid buzzing noise. Replaced the relay and it's still doing it.
Mine work but it gets stuck when turning right and I have to take it down myself
Thanks you it's really helpful
What if
When I do left turn signal
It goes to right side ???
My left blinker won't flip back automatically, so after every left turn I need to flip it back manually. Do you know what could cause this?
sounds like the blinker arm is damaged where it connects to the column
Great video need to replace mine
Having any tips when the left turning signal flashes with the brakelight while braking?. Its the same when i put my car in reverse and the lights starts flicker as soon as i turn the signal left!
change my turn signal switch for my 2004 toyota 4runner and dash lights not working
Thank you for your time and video
front rt turn signal not working, changed 2 different bulbs w/ no success. Any further suggestions?
Check your socket. See if there's power and ground getting to it, if there is - your socket is bad
I will try your suggestion, thank you for taking time to reply.
I had a 2011 Toyota 4Runner with a left brake light that constantly malfunction. Changed bulbs and even switched sockets with no success. Mechanic said it was in some circuit board, several hundred dollars to replace, but they had an unusual process to get it working that involved removing tail light bulb, pressing brake peddle, then replacing both bulbs, and surprisingly, it worked, supposedly faking out that circuit board. I don't know if this similar situation with this 2008 4Runner.
Cheers Mate. Very hellpful vid💯👊🍻
Thanks , saved me money.
Very helpful !!!
Thanks buddy!!
Hello. I have a toyota yaris verso. I know u don't see that car in USA. My problem is when I put my directional to the right the headlights turn on, but not always. Also notice when move the switch just a little bit the headlights turns on (still in off position) what could it be? a fusible?
Sounds to me like your switch is bad, all you're doing is moving with the switch and it's doing something it's not supposed to.
Thank you Sr. You help me a lot with you knowledge.
Hi great video, I have a 2008 Honda Civic Ex and when I turn on my blinkers the hazard lights also flash. I checked all of the fuses on the vehicle and also the wiring.
I was told it’s the turn signal/hazard lights relay. Do you know where it’s located? If so can you please let me know. I opened up the turn signal stock and cleaned all the connections. Not sure if it’s a relay, check everything but can not find the issue thank you.
Hey I have the same problem were you able to know and fix what the problem was? If so will you please help me
Jaime Hernández, Yes the problem with my 2008 Honda Civic was the wrong bulb. Make sure your light bulb is for your blinkers / low beam light, it has a double use. The sales rep at auto zone sold me the wrong light bulb for my vehicle. Hope this was helpful.
@@sheba6779 thank you!
Thanks for this video, straight to the point. 👍👍👍
Was that part he showed the one he ordered?
Thank you very much very helpfull
Thank you Sir
I have the same problem on my Toyota
tazz
Hey I might have missed it but my Tacoma doesn’t have any lighting up. No turn signals or hazards. Already checked the fuses and relay and signal switch. Still nothing.
I have the same problem. Did you get it fixed? What was it?
Did y’all find the problem???
I have the same issue but on the right indicator
Mine comes on but blinks really fast is it the turn signal relay or the bulb?
So i changed the bulb, the fuses and the flasher unit on my 2000 chevy silverado , but my right rear turn signal still doesn't want to work. Could it be the bulb socket or turn signal switch??
Could be the socket, or even the bulb.. I think the switch would affect both - front and back lights
@@MakeItEasyMechanic It was the socket haha, thank you!!
@@nestorperez5176 Thank you for telling what the problem was
Super helpful thanks appreciate it, will try this.
i honestly doubt you’ll see this but if you do please reply. same thing happened to 2007 galant. my back right brake light was out (faulty wiring) i fixed it and originally only my left side blinkers stop. i just swapped a load of fuses.. now neither side works, and my inside lights and the buttons on my key
Pretty sure this what's happening in my Lexus IS250 2007. My right turn signal is intermittent. The left one is fine. And the hazards work, so it's not the bulb.
I have an '06 Ranger. All the blinkers works fine except the passenger front. Inside the instrument panel you can hear it blinking fast but doesn't light, outside the bulb lights solid. None of the bulbs are burnt out. No matter how much I play with the switch it doesn't blink normal. I need help diagnosing this please
What if new bulb burns out as soon as you place it in? I've worn gloves and it goes out immediately
Never touch the bulb no matter what still hold it by the metal part or it could be the wrong one for your car or a faulty fuse
Do you have a video about the flasher? Both mine work only occasionally.
Thanks!
Not yet, but thanks for the idea
Soo I have the same problem I install a new switch and still having the same issue. Any ideas
Great really2 simple....like us as a non technichian also can understand it...great...i give it a like and subscribes to your channel👍
Going thru bulbs on both sides every 3-4 weeks on 2016 Tundra. Thoughts? Thx.
Ok thanks amigo
That was Great. But how about the 2021 Tacoma?
My lights will go on and off while driving. Could this be the reason as well?
Same thing here.
It works this is useful
fog lights r not working on my pt cruiser 2002 even if i changed the bulbs,what fuse or relay responsible for that?
thanks
Was your bulb burned out?
I have a Hyundai Tucson 2007 and the turn signal will not shut off after I make a left turn. It works fine after a right turn. Is there a way I can fix this without replacing the entire unit?
My problem is that, sometimes they work and some don’t, and i could get pull over anytime
My fiancé just bought a vehicle and the right turn signal only works if he has his foot off the gas...any thoughts or ideas?
Perfect teaching. Thanks!
Dean Jackson M.Ed
Where can i buy a signal flasher for a kia sportage 95 and the turn signal switch?
Can the flashers work and blinkers not and the problem be the relay? Thanks.
Yes, turn signals and hazard lights are typically controlled by different flasher relays
This is a super helpful question and answer for my situation, thank you
Thank you !!!!
I got no electricity in fuses and hazards are working, light bulbs are fine what can cause issue? BTW the high beam light is out too any ideas?
Am having the same problem, mine both right and left are not working can I also change or what should I do
Worth a shot
What if it sounds like it's blinking - the left side - but it's not. It just makes the clicking sound. Not always though. But half of the time
Both my turn signals won’t turn off
*Yo, quick question for anyone, any idea what the issue would be for 1tail light not responding to the blinker switch. The bulbs work, but 1 side doesn't engage with the blinker. Have checked online, and can't find any main diagnosing. Fuse/Panel, does not seem to be the cause.*
This is exactly the problem i have on my car... do you have any idea how much it cost to by the new blinker?
Roughly, in a $35-75 range.
Did you...check...your....blinker flui..
No....thanks I will send my daughter in to get some
I have a jetta 2012 and my left turn signal, left flasher, and left headlight does not turn off but my right side does. I replaces the bulbs but no use, does anybody know the reason?
Awesome . I will attempt this repair soon!
I have an 1989 toyota pickup (2WD). The right is okay but the left turn signal has the same problem as this Tacoma, and it makes a "bleeh" sound for the left. Why is that?
Not sure what "bleeh" sounds like lol but my guess is - the switch is failing internally, and there's poor connection when you switch it left
@@MakeItEasyMechanic Oh. It makes sense. Thank you
What if both blinkers flashes fast replace both light bulbs but didn't fix the problem
turn signal relay.