That's crazy I have been doing roofing for 20 years never knew the direction's were on the package 😂😂😂 that would have definitely helped speed up the learning process
You can mark out the 2nd through 6th course cut off measurements (OC shingles: 6.5", 13", etc.) on a scrap piece of plywood/board (measured from the left factory edge) using a Sharpie marker. Then all you have to do is line up each piece of shingle and mark where you need to cut with a knife. This way you don't have to use a measuring tape each time you make a cut and you will find the measurements/cuts will be more consistent. It will take less time also.
Going to be doing my own roof. Did roofing in my younger days. Only have one small valley. The shingles will be about $1,500. Not paying someone 10k to do it.
Hey, Jim! Thanks for the video. Much appreciated. I noticed that the directions on the Owens Corning package says that the first cut made is 6 1/2" instead of 6". Any particular reason that you chose 6" ? Was it to save material perhaps? Thanks again!
Thanks, but all the little detail stuff at the beginning that you chose to skip over would have been helpful. Still looking for a video that demonstrates what is on the packaging.
May want to add a clip/comment on when you end/finish a row and there is less than 6" (a tiny piece) It's great to start the way you did, but you have to pay attention to the other side. Also, you may want to mention when you finish at the ridge... and having a small amount there... and how you can use a story pole to get it just right instead of having 3 or 4 inch area remaining..... Overall, looks good thumbs up
The last roof I did was on my first house in 1973 with 3-tab shingles, of course. I came here to find out if laying the first course is the same, i.e., a row of reversed shingles. You let me down, Jim!
The color on the plywood is because it was the top sheet in a stack, they paint the edges on all four sides a color pertaining to the thickness (blue is usually 1/2"), the entire top sheet caught a lot of overspray.
At 1:49 you say you use the nail and cap because you didn't know how long it would take to get it roofed. Would you leave the roof exposed to the elements at this point or cover with a tarp?
Hi Colleen, Depending on where you are. I live in a mild climate and not much snow or rain but if the roofing paper is laid down properly it should protect the roof. If I were doing a house I would use the synthetic underlayment which hold up really well. Of course right now some items are hard to find, I am going to build the doors because I can't get the garage door. Waiting for drywall too. Thanks for watching I appreciate it!
@@anthonysuzanne9901 Maybe you're buying better quality hook blades than me but I can't manage to cut more than a few shingles with them before they wear out. And waaaay too much effort.
Agreed. Music kills these type of informative vids. But yours wasn't bad. But try cutting it out as you talk and only playing it as your working moving about without dialogue. Thanks
Sorry Andrew, I just wanted to be sure those with less experience gets all the information to do the job right. I appreciate you watching and again sorry you feel it's to slow I'll work on that.
You stagger so that all the ends don't meet up, which allows water to penetrate down to the roof decking. Cutting six inches off an end allows water to drop down onto six inches of shingle and shed down off the roof.
That's crazy I have been doing roofing for 20 years never knew the direction's were on the package 😂😂😂 that would have definitely helped speed up the learning process
Right?! Hey thanks for watching I sure appreciate it and if you have bonus tips that would be great for the community.
It ain’t that legible, but I was able to read 5.5in. Exposure and cut 6.5in on stagger for Oakridge
Straight nailing was pleasing.
Thanks for watching I appreciate it!
Different people have their own way of laying out the roof. As long as you dont have leaks or blow offs who is to say your wrong.
Well thanks for the input and watching we all appreciate it!
1/2 inch overhang is not enough.
Great video. I'm gathering information for a garage re-roof I'm about to do. I'm going to snap chalklines so I keep the courses straight. Thanks!
Chalk Lines are your friend, Be careful and get it done! Thanks for watching David.
You can mark out the 2nd through 6th course cut off measurements (OC shingles: 6.5", 13", etc.) on a scrap piece of plywood/board (measured from the left factory edge) using a Sharpie marker. Then all you have to do is line up each piece of shingle and mark where you need to cut with a knife. This way you don't have to use a measuring tape each time you make a cut and you will find the measurements/cuts will be more consistent. It will take less time also.
Thanks that was so helpful
Glad it helped Cedric, thanks for watching and taking the time to comment I sure appreciate it!
Going to be doing my own roof. Did roofing in my younger days. Only have one small valley. The shingles will be about $1,500. Not paying someone 10k to do it.
Outstanding! please comeback and let us know how it goes. Plus if you want to show your work off, email pictures.
Great video love the music 🎶 very informative thank you sir 😊
Thanks for watching I appreciate it!
Hey, Jim! Thanks for the video. Much appreciated. I noticed that the directions on the Owens Corning package says that the first cut made is 6 1/2" instead of 6". Any particular reason that you chose 6" ? Was it to save material perhaps? Thanks again!
That is correct because it seems to workout better
no. cut 8 inches. most arch. shingles are 39 - 40 inches long, 8 inches goes 5 layers perfect.... less waste!!!❤
Thanks, but all the little detail stuff at the beginning that you chose to skip over would have been helpful. Still looking for a video that demonstrates what is on the packaging.
May want to add a clip/comment on when you end/finish a row and there is less than 6" (a tiny piece) It's great to start the way you did, but you have to pay attention to the other side. Also, you may want to mention when you finish at the ridge... and having a small amount there... and how you can use a story pole to get it just right instead of having 3 or 4 inch area remaining..... Overall, looks good thumbs up
Yeah that's a great suggestion and will help my viewers. Thanks for watching!
The last roof I did was on my first house in 1973 with 3-tab shingles, of course. I came here to find out if laying the first course is the same, i.e., a row of reversed shingles. You let me down, Jim!
I am sorry I let you down, didn't mean to but I did mention it at ruclips.net/video/BVWdAiWnhjs/видео.html this time in the video Hope it helps.
What is the purpose of staggering the shingle, (6.5, 13, 19.5, etc) Is it for the appearance of the roof
Hi Mike, not only appearance but to alternate seams to shed water correctly.
If you don't stagger, all the ends of each layer will meet up. When ends meet up, it leaves a gap where water can penetrate into the roof decking.
The color on the plywood is because it was the top sheet in a stack, they paint the edges on all four sides a color pertaining to the thickness (blue is usually 1/2"), the entire top sheet caught a lot of overspray.
Thanks for the info! Thanks for watching too, I appreciate it.
How did u do the roof tip?
Are you talking about the cap or the ends on the caps?
@@ILikeToBuildStuff The ridge cap...
@@luisbatista1103 I did purchase the matching cap shingles and used a 20' ridge vent for heat release
Why not leave the left factory edge intact and just cut on the right? Ends up being the same anyway.
At 1:49 you say you use the nail and cap because you didn't know how long it would take to get it roofed. Would you leave the roof exposed to the elements at this point or cover with a tarp?
Hi Colleen, Depending on where you are. I live in a mild climate and not much snow or rain but if the roofing paper is laid down properly it should protect the roof. If I were doing a house I would use the synthetic underlayment which hold up really well. Of course right now some items are hard to find, I am going to build the doors because I can't get the garage door. Waiting for drywall too.
Thanks for watching I appreciate it!
Score shingles on the underside, bend, then snap. Trying to cut all the way through from the top is a fool's game.
I sure appreciate you joining in here and the great comment it means a lot to me that you would take the time to watch my video!
@@anthonysuzanne9901 Maybe you're buying better quality hook blades than me but I can't manage to cut more than a few shingles with them before they wear out. And waaaay too much effort.
Why are shingles installed in a step up formation? I never understood that.
Not sure other than overlapping concerns
Stagger the seams ...
I just use my knife length for measuring. .no need for measuring tape...
Thanks for watching and the tip we all appreciate it!
Would be better without music.
Thanks for the input, I appreciate any help I can get!
Agreed. Music kills these type of informative vids. But yours wasn't bad. But try cutting it out as you talk and only playing it as your working moving about without dialogue. Thanks
I thought the packaging kept it all at 6,that way less confusing
I gave measurements for each layer instead of adding up how much to take off but the actual length of each one, Sorry I confused you, didn't mean to
based on your terrain you look like you're in wyoming lol or there abouts
Awe man you are so close, LOL in Arizona
You totally confuse me with this puzzle
Sorry, just look at the instructions on the packaging it will help.
Yeah, doers don't necessarily make good teachers.
Slowwwwwwwwww
Sorry Andrew, I just wanted to be sure those with less experience gets all the information to do the job right. I appreciate you watching and again sorry you feel it's to slow I'll work on that.
@@ILikeToBuildStuffI'm sure Andrew has tons of videos on how to be a speedy roofer, no need to work on that haha, I appreciate the information
I know I'm not a roofer, but WHY do you need to stagger shingles like that
for looks and placing the edges to not leak when raining
You stagger so that all the ends don't meet up, which allows water to penetrate down to the roof decking. Cutting six inches off an end allows water to drop down onto six inches of shingle and shed down off the roof.