Это видео недоступно.
Сожалеем об этом.
GMC Chevy Truck ABS / Brake Light on C0265 Solution
HTML-код
- Опубликовано: 15 авг 2024
- This is a very common problem on the early 2000 GMC Trucks. It affects the Tahoe, Suburban, Yukon, Silverado, Sierra, Bravado, Jimmy, Blazer, Sonoma, S10 and any other GM Vehicle that has the Kelsey Hayes 325 ABS Module.
These ABS Modules need to be rebuilt for the following issues.
ABS PUMP IS ALWAYS RUNNING
RELAY CODES
ABS/BRAKE LIGHT ON OR INTERMITTENT
If you have any of those issues here is a link to our repair service. We have a 24 hour turnaround time and a Lifetime Warranty.
www.automotive...
You can drive the truck with it removed you just need to cover the ABS Pump to protect it from the elements.
Caution
With The ABS Module removed you will not have ABS or Traction control so Drive with caution. We are not responsible for any Accident or injuries that may occur with the ABS Module removed. Drive at your own risk only if you have to.
Tools used in the video
Torx set amzn.to/2JwXu0k
Screw driver set amzn.to/2IExhLX
Scan tool (used in video) amzn.to/2JvWbP6 $2300
Scan tool (eco version) amzn.to/2GII4nD $500
Scan tool BlueDriver amzn.to/2MMM5MF $99
Here is a video showing how we repair these EBCM modules ruclips.net/video/_MDpzy0xC2I/видео.html
You ROCK! THANK YOU! awesome video.
What model Autel scanner is that??
I am an auto mechanic and this helped me instead of me doing lengthy research.
Same hear. I have some auto skill's , But it seems easy to replace. My truck is 2001 Silverado. The EBCM is in the same place like his video shows. kind of tight to get to. The only thing I don't know is the model number of the EBCM. I hope it's the same one he's got listed on his note.
Could also be a dirty ground. Before you replace the control module, check for a clean ground. It might save you some money.
Where's the ground at?
I'm bout to buy a vehicle with this issue.
The ground for the module is on the frame opposite to the abs module beneath the driver door-there should be about three wires, the heavier gauge wire is the module ground. You'll want to gingerly remove the bolt and clean up the surrounding area and the wire terminal ends with a wire brush or the like. When you put it back together use a dab of dielectric grease to ensure a good connection and to dispel water.
Happened to me with my water reservoir. The coolant light wouldn't go away after I took my tank out and flushed it.and it said to get it to go away you have to replace it.i soaked the sensor and the end it goes into on the tank in purple power and the light went away
How long does it take to remove and reinstall a new one?
you didn't show the actual repair!!!!
He didn't show the repair because that is what he is selling for $60. That's a bargain. Read the entire description below the video.
He took it apart, soldered all the cracked joints then put it back together.
Jeff Brill Luke Perry's look alike...😂😂😂😂🤣
@@superduty4556 Actually you should re-flow all the large (power) connections. These boards are multi-layer PCB's and sometimes the inner board connection breaks. So if you re-flow the entire board or at least all the large connectors and get a nice shiny look to the solder, not dull grey (Cold joint) you should be able to reinstall and have no problems. It is actually easier to remove the unit from the frame rather than feel around and screw around and strip a screw or break the head off.
@@edcrabb yes, I remember reflowing my PS3 back in the day.
You said you repaired the ABS module. What kind of repair you did? Can you more elaborate?
here's a COMMON repair for this module ruclips.net/video/_MDpzy0xC2I/видео.html
I wish I could do this but the heads of the hardware are so corroded I can't get the T20 bit into them. I'll quit while I'm ahead.
Spent several hundred dollars on a garage to try and repair my ABS system/pump. They repaired the assembly, but now it engages incorrectly due to a bad wheel beaeing/toner ring. What a waste of my time and money. I'm just gonna unplug the friggin thing and remove the ABS light in the instrument cluster
Had the same problem. I replaced the sensor in the existing wheel bearing. But .... mine was a so so wheel bearing on the driver’s side. Replaced it with sensor included. Solved ...
Do you have to have it hooked to the computer to do this
U didn't finish ur job.
Thanks alot is that problem lit the 4w not working????
???
I replaced the module 2 year ago the light go away for 3 week n it came back on n off. I replaced the abs sensor n the abs light is still on n is code 267. How can I fix code 268 ?
I have 268 as well, I think it is the control valve / pump bad or going bad, you can get an autel bluetooth reader that works with your phone on amazon if you don't have one already and you can clear the codes and do an auto bleed, listed to see if your pump/valve kicks on. They say to check grounds under drivers seat on the frame, mine were fine. I will replace abs control valve / pump and let you know, but it may not be for a few weeks
Brake sinking pedal it can be due to this failure???
Hold up!! before pulling that module out try this. Wiggle the power connector to the module. the one shown here with the red seal around the plug. By accident I found that by moving the plug I could make the ABS and Brake lights come on or go off. Probably some corrosion on the terminals. I slightly bent the male lugs so they would make better contact when the plug is reconnected. It's been awhile and both lights are still off. Probably a good idea to check the grounds too.
Hello. I'm about to check they out.... How can I find the grounds? Thanks.
I replied but I saw a RUclips video by Scott The Fix-It Guy that goes over the procedure. Yukon-Tahoe Brake Warning Lights-10 Minute Fix. Good luck.
@@meansnothingnow OK! You seemed to know where were located the grounds...
Yeah that’s been happening with mine I think I’m gonna tackle it now that I saw your video what is the average cost seems they’re all over the place I have a 2001 Silverado 1500 HD
Here is a link to our service, send it in for a fast and reliable repair.
www.automotivecircuitsolutions.com/collections/chevrolet-1/products/gm-truck-abs-module-rebuild-service-kelsey-hayes-325
Did you replaced module or took it apart??
So your video is nothing more than a sales pitch to repair our modules, correct?
Actually you should re-flow all the large (power) connections. These boards are multi-layer PCB's and sometimes the inner board connection breaks. So if you re-flow the entire board or at least all the large connectors and get a nice shiny look to the solder, not dull grey (Cold joint) you should be able to reinstall and have no problems. It is actually easier to remove the unit from the frame rather than feel around and screw around and strip a screw or break the head off.
Thank you for sharing that Bubba Gump, that was actual handy info we need.
@@MercuryRisingFast basically means to re-solder the joints cause it gets corroded.
Thanks, I didn’t even think about doing that on my 09 f150. Control module is bad and they are expensive for a new one. I’m gonna try and reflow all the joints.
What if the bolts are stripped???
I have that same problem with my 2002 Chevy Tahoe and I have the new module my question to you dose it have to be programmed or can I just put it on and clear to code.
As long as the module is an exact match then there is no need to program it.
Automotive Circuit Solutions thanks
Is it cheaper for repair or to just get a new one?
Since the original problem was intermittent, you can't be certain the problem has been repaired. Shouldn't you take it for a test drive and shut it off a few times. I've seen this code with air in ABS.
Hello,
Yes we did take it for a test drive after to confirm the issues were corrected. Also our service comes with a warranty and the customer never came back.
What did you do to off abs warning light ?
Just erase the code
So how did you fix it?
Go to pick and pull and get another one, they are like $25
What does this cost? And does it fix the abs not working? My abs does not work on my 02 tahoe. Thing skids like it’s on ice
Does cause your e brake not to work cause I don’t have an e brake and both of these things come on it’s soft all the way down and doesn’t do nothing for my truck or did my abs sensor go bad along with my e brake lol
Have you ever had an issue with your truck were you turn the key to start the vehicle but there is no start. And you have to wait awhile in order for it to start again.
Loose wire on the starter solenoid that what was wrong with mine
Hello, 2017 equinox, pulled two codes C0110-00 and C0110-04 (pump motor circuit), I did verify ground and two positive terminals on the main connector no issues there. Tried to test pump and solenoid valves with my scanner but it tells me that "ABS solenoid or pump malfunction". I believe it's a module, what do you think? can you repair it?
What repairs were done? Just showed you taking it off and said it was fixed.
We resoldered a lot of contact points in the module, we have a repair video to be apart of this one coming out this week.
How you remuved the red click from plug?
How did you repair the module?
ruclips.net/video/_MDpzy0xC2I/видео.html
Lol what was that? I guess now people can remove the control module. No repair info here. Why you didnt show the solder joints that is the culprit.
Please elaborate. I'm so pissed this guy just SKIPPED the whole "Solution" part of the problem!
Hey,my abs & brake light is on and my speedometer don’t work.code showing p0700.I changed both vehicle speed sensors and still same.transmission only has a slight delay on shift but works good.any ideas?08 Chevy Express 3500 cargo van.4.8L
Will it damage anything if I don’t ?
2002 GMC Sierra 1500 changed all calipers great booster Master brake cylinder and able to build pedal pressure with engine off as soon as I turn the engine on brake pedal goes to the ground and is soft cannot build up pressure any ideas
I had this problem. My cause was leaking brake fluid. And the reason it was leaking because the brake pad was basically gone so the caliper was just basically open and loose and leaking fluid. Just check your pads incase I know you changed you stuff out but you never know
Or your metal/rubber brake lines rotted
No leaks. Dry brake linedry calipers. Not losing any brake fluid when I keep pumping.
@@janusznedza5034 same problem here, what did u end up doing to fix your problem? I have also changed my hydraulic booster n master cylinder bled the brakes n my brake pedal just stays in the floor.
Does this have anything too do with affecting the 4wd or braking I have same code after my push bottom 4wd wouldn’t disengage back into 2wd and finally got my 2003 blazer back into 2wd these lights came on does this cause any type of issues in drive ability or is it just make for a visual abs /brake light that has no symptoms
Can this sensor be replaced with a reman or rebuild only
2:28 WHAT DID YOU DO TO REPAIR IT?? WHAT DID YOU REPLACE OR FIX OR WHAT DID YOU DO IN THERE?
You have to open up the module and reflow the board to get it repaired. Or you can send it to us and we'll do it for you for only $60.
Automotive Circuit Solutions awesome! Thank you for responding. Can I drive the vehicle without it while it’s out for repair? It is my daily driver.
@@MarkiedosOCHO We dont advise it. But yes technically you can drive it.
Again, thank you very much for the assistance.
Question: I opened up my fuse box and noticed the fuse for the ABS was gone. I put a brand new one in and the EBCM started whirring loud like a drill motor or a stand mixer. Does that mean it's working or that I need to replace it?
How did you fix I so I can fix mine?
We have a video on our channel how to fix these.
I just installed a remanufactured abs module (made sure it was the correct kind) on my 2002 suburban 1500 LT and the light is still on. They said I would need to delete the codes or double check the fuse box is in order. I'm a little stumped
You might have other issues. Get it diagnosed to see if there are any present fault codes.
@@AutomotiveCircuitSolutions nope just the relay circuit code was the only thing
@@OpiumMonkey did you ever figure it out?
@@CripplelovesWolly never did :/
Hello. I have an o3 Yukon, brake light, ABS and TC lights on and AC blower not working.
Is this part of the same problem in this video?
I am having this issue but i disconnect the wires from the abs and use my test light and i find one of the wire flickering the test light wat could cause that? Seeing there is not connected to the abs
That is likely the dataline that you are testing.
@@AutomotiveCircuitSolutions ok it's a blue wire... wat do u mean can drive with out the abs? Wit my 3500G Express cutaway Dont matter how much I bleed the break is like air is still in the line
Looks easy on RUclips, but try it in person, I made up all kinds of new cuss words. I really want to meet the guy designing these chevy and GMC vehicles so I can smack the crap out of him.
Currently in my 2005 Chevrolet Trailblazer I have both the ABS Light and Brake Light, which illuminates almost as soon as the truck is started, and after running a diagnostic with a scan tool I was presented these same codes. Could this method fix my problem as well? And I must also ad, brakes are functioning just fine as expected.
Yes the 2005 Trailblazer has the same ABS Module. Send it in we'll get it rebuilt for you.
so did you repair it or replace it? how many bolts are there?
4 torx
Would this cause me to have to manually release my hydro boost when my brakes lock up
Ive got a 2002 Suburban with the ABS coming on intermittanly also. What year was this vehicle? Not aware that you couold read codes on the ABS system.
Are you guys still repairing these modules
Yes we are still repairing them. You can find the link to the service in the description of this video.
I just change mines from 2002 GMC Yukon but for some reason now marks my battery is low fuel cage won't work and abs airbag light are on........I NEED HELP AND I GOT MODULE REBUILD FROM EBAY......HELP PLEASE
Why didn’t you show any of your workings on the abs…!!!😢
What kind of tool was that. I get the Tx but was that just a regular combo wrench?
Hello. It's a 1/4" wratchet wrench designed for 1/4" bits. Link to the set is in the description.
I have a 02 GMC Yukon with the abs and brake light and the code c0267 and c0268 . I change the same thing it came back on 3 week later. Need help
Did you replace it with a used one?
No new one from autozone
that was real helpful were was the repair part at
We recently added a repair video attached to the end of this video, or you can check out our channel as well.
Instructions unclear, got nuts twisted in driveshaft.
Do you have to clear the code in the scanner in order to remove the lights inside the dash?
No once the module is fixed, the light will go away on its own. If it doesn't you likely have other issues on the truck.
Would that cause it to sop running and crank but not stay running?
Yeah what happens when you have two screw head that are stripped and one of them is on the far side and you can't fit your hands in to get it out?
In that case you'll have to remove the abs module and pump assembly. Once removed you can get those bolt removed with a bolt extraction set.
How do I send mine for repair? Mine is from a 1996 GMC K2500 Suburban, 8600 GVW, 7.4L Gas. Mine has the black plastic top and not the metal.
What is the Average or actual repair cost ?
Is there a way too bypass this unit and route your brake lines differently ? Ridding it all together ? I know I heard this before this is the same issue with 88-98 suburban Silverados
The units are like $300 so I'd guess $400+ for a shop to change it
I went to the junk yard and bought one for $35. My was buzzing so in was the electrical box not the pump where the brake lines connect.
mine just starting buzzing even when the car is off ?I'm going to try this thanks
Nice info comes in handy brother now I know how to do it myself...much appreciated..🖕✌️
How is that handy maybe i don't get everything on my video .
You showed Nothing as far as repairing the module
How do you repair them I’m curious
ruclips.net/video/UXrNa_8hWZw/видео.htmlsi=fxGX3oxgKNaP82wx
If I took mine out . Could I send it too you for repairs
Yes you can. www.automotivecircuitsolutions.com/products/gm-truck-abs-module-rebuild-service-kelsey-hayes-325?_pos=2&_sid=a77f4ced4&_ss=r
How many hexnuts are there? what is the part number for the module?
Can you run with out this module on or you have to have one on
The truck will run and drive fine without the module. However we do not recommend you drive without the module because you will have no anti-lock brakes.
@@AutomotiveCircuitSolutions alright thank you I wont just while I send my unit for a repair
Lo intentare tengo ese problema con mi chevi
How much does this cost to get it repaired at a shop?
We charge about $120 for repair and removal and installation. Most shops will not repair the unit they will get a replacement.
@@AutomotiveCircuitSolutions where are you located? Can i send you mine to get fixed? My email address is ealston2874@gmail.com, thanks in advance
@@GOMABSIGMA did he reply mine is bad too
When 3 out 4 of the T20s strip just cut your losses and remove the annoying bulbs...... Anti lock brakes system won't work any better but you can just pretend they are fixed lol
It is easier to just remove the ABS fuse and both bulbs will turn off. And the brake one will still work as indicator for Parking Brake.
Also easier to change the module altogether with one from the junkyard. Just a little messy when removing/reattaching brake lines.
Everything was going great until I realized 3 of the 4 bolts are RUSTED!😣 Now how do I remove them in such a tight space? 🤔
Had similar problem, all 3 bolts 🔩 no issue's the last one stripped I'm driving the truck with the abs light on
Take the bulbs out and the annoying light problem just goes away 😁
What scan tool are you using? It looks neat.
Here is a link to it amzn.to/2LVyKE3 . Great scan tool, very capable.
@@AutomotiveCircuitSolutions holy crap, that's an expensive tool!
@@Joe_1776 It payed for itself 10 times over in the last 2 years. Well worth the money.
I have the same code but sometimes when I’m applying my brakes my rear wheels lock up, and I don’t brake that hard. It happens every so often, does anyone know if replacing the module will stop this ? I have a 2003 gmc Sonomas S-10 model SLS.
You’re asking about a different vehicle, with a different problem 🤷♂️
Can you replace with a used one from junk yard? Bc for my suv it's around $400
Trisha Hamilton NO! Don’t do it! It’s just a waste of time! There is a place in Arizona you can send you’re module to for $45 7-10 day turnaround with warranty no ABS ever again
@@mdr9738 can you tell me where or the info so i can send mine thanks
So I just take the thing off send it ? And they’ll send it back fixed ?
@@dommybigshot21 yes
Michael Salt thank you
Did u have to reprogram new abs module?
No, we repaired and reinstalled the same module that we pulled out. That way there is not programming necessary.
C0265 and C0267 codes require the same replacement part if I am correct.
And the c0240 for Chevrolet colorado?
Easy stuff, thank you.
do you have to erase the codes for the light to go off?
No, once the repair is made the lights should go away on there own.
Automotive Circuit Solutions i changed both front bearings because one wheel sensor was bad according to scanner, replaced both the light still on????
How
Good video, I think I’m having the same problem... What’s the turn around time on a module repair if i send it to you??
We typically repair and send back within 24hours of receiving it.
yea thanks for nothing
God bless nice job
What size & kind of bit did you have to use to take cover off?
Would it be easier on my own rig just to cut an access panel on the floor?
Hmm! You just showed where ecbm is located and how to unscrew it. Actually replacing unit or what was done.....IS MISSING. not very helpful
What's the turn around time on this , if I send it to y'all ?
We repair and send back within 24 business hours of receiving .
thanks. any warranty ?
Lifetime warranty.
Thanks brother , definitely gonna send mine in soon.
my 2000 tahoe does this so im gonna try and replace mine hope this will be my issue
Where are located, I'm from District of Columbia and what is the cost of the reapair
Please tell me
C0267 Pump motor circuit open
C0269 excessive dump time
HOW DID YOU GET YOUR HANDS UP IN THERE ?
Jacking the truck up or putting it on the lift makes it a lot easier.
Hi,I changed my hub bearing and now brake and abs light comes on any suggestions? Thanks in advance.
Most likely something wrong with the wheel speed sensor on the hub that you changed. Check see that it has a proper connection.
Thanks I will do that...
You didn’t explain anything!!!!
🤣🤣🤣
he didnt do anything the computer does it you can rent these
How did you repair it. Liar. You just bought another
Would be nice if you explain how you repaired it you doofus!
We know how to take it off. This was pointless
here is part 2 ruclips.net/video/_MDpzy0xC2I/видео.html
Didn’t help at all!