How to Replace Passenger Side Axle Seal 03-13 Nissan Murano
HTML-код
- Опубликовано: 7 сен 2024
- Buy Now!
New Output Shaft Seal from 1AAuto.com 1aau.to/ia/NSTR...
In the video, 1A Auto shows how to replace a worn or leaking axle seal. The video is applicable to the 03, 04, 05, 06, 07, 08, 09, 10, 11, 12, 13 Nissan Murano
This process should be similar on the following vehicles:
2009 Nissan Murano
2010 Nissan Murano
2011 Nissan Murano
2012 Nissan Murano
2013 Nissan Murano
2014 Nissan Murano
🔧 List of tools used:
• Pry Bar 1aau.to/ocM/1AX...
• 21mm wrench
• 16mm Socket 1aau.to/okB/1AX...
• 21mm Socket 1aau.to/oeH/1AX...
• 32mm Socket 1aau.to/or/1AAS...
• Axle Fork
• Slide Hammer
• Trim Tool Set 1aau.to/ods/1AX...
• Side Cutters
• 1/2 Inch Breaker Bar 1aau.to/oaE/1AX...
• Ratchet 1aau.to/omx/1AX...
• Socket Extensions 1aau.to/okB/1AX...
• Torque Wrench 1aau.to/ogI/1AX...
• Brake Parts Cleaner
• Cloth Rags 1aau.to/obn/1AX...
• 10mm Allen Wrench 1aau.to/ou/1AXA...
• Center Punch 1aau.to/oag/1AX...
• Drain Pan 1aau.to/oa3/1AX...
• Floor Jack 1aau.to/odf/1AX...
• Hammer 1aau.to/ocR/1AX...
• Jack Stands 1aau.to/ocY/1AX...
Subscribe: / @1aauto
Check out our playlist:
Nissan Murano 2009-2014 2nd Generation: • Nissan Murano 2009-201...
For More Info visit us at 1aau.to/h/wj/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
You try that tap tap tappin that axle up here in the rust belt states like the Pocono mountains here in Pa... Me my Bobcat and Raccoon will sit here eating popcorn & peanuts laughing our cans off at ya...
See my video on removing that bad ole right side CV axle... I make short work of it totally..
You don’t ever, EVER hammer tap on a seal ring when installing... Sue was very careful but most people don’t.
If you don’t have a seal or bearing tool kit, you can simply use a piece of pvc pipe to push evenly.
There is a spec limit on this due to possibly coming loose if not installed correctly or dust getting into the seal if pushed in too deep. I'm currently working on a design that can be 3D printed in 30 minutes that you can use along with a long pipe or elongated head hammer to tap from a closer position.
The best transfer case drop and refill Ive seen yet and by a women.
Giver her some power tools
Thanks for the video, I have a better understanding what's evolved in changing the seals in a Nissan Murano
Thanks for the precise and easy to understand illustration.
Sue is so good. Great content.
very helpful video ,straight foreword A1 auto you can't go wrong
+jf Thanks for checking us out! 1AAuto.com
This does not specify if this is an AWD or front wheel drive, things like shaft seals and axles are not necessarily the same for each model, please specify it makes a difference. Thx!
The most unbelievable video i have ever seen. That job was done 10 minutes before she started. No way that axle separated like that, total b.s.
If the car was well taken care of it's possible, i had alot more problems because the one I worked one was a 2011 and looked like it had been neglected. Pulling the entire passenger axle assembly out of the diff was actually easy once all the prelim stuff was done, easier than putting it back in since I had to replace parts of the CV assembly for both sides.
The seals proved to be a real pain in the butt, i had to phone a friend.
I am a man and a I do this and you are owsum I love it thank you for your video I will subscribe
I get a kick out of the directional rotor being on the wrong side....
Also...if you need to hammer in a seal, fill the backside of it with assembly grease, so the spring doesn't pop out.
Nice informative "How To" on this axle seal.
I have a 99 maxima and replaced right side seal and it still leaked . Found out the parts store sold me seals that were same for both sides. Not right the left and right seals are different sizes on Nissan . Now I have to redo the right again . Be aware of your parts and where you get them. Always check OEM specs and then seek parts to match if not getting them from dealer .
Do I need to drain transfer case fluid if I’m only replacing the cv axle?
Hard to believe that the bearing cane out that easy from the carrier
Had to take one out with the bracket and smacked it off with a large hammer, took a couple of blows and finally released. That bracket can be removed by dropping the exhaust a bit to allow for more clearance and removing half of the axle from the inner booth. My CV axle was bad so I just completely removed it but if you're trying to just attack that seal, it will be a pain if it is seized.
That is for the demonstration, in real live is very hard to pull off the axle, and too install the seal is very difficult due to the room.
Thank you very much
Thanks
Really excellent installation
+Mohsen Saad Thanks for checking us out. 1aauto.com
I have been trying to do this and it appears that I keep getting leak around the seal. Did you experience anything like this?
10:00 i think three might be a better way to install that seal
Lol she ain't greasing anything!! Raw and dry!!
Should put the lug nuts on before using the pry bar as leverage for the axle nut so you don't ruin threads.
+Bozscaggz Z Thanks for the tip!
Thank you very much the video explains the process very well. But even I need your help to find the check point and refill point of the difference fluid.
I Try to find them by guiding me through the video, but it seems to be different in murano 2005. Thank you very much for your help
2005 is a different model and configuration.
Great video! Can I use the check plug to fill the transfer case instead of reaching out that top plug?
In theory......possibly.....but in real life, most likely not. There's not much clearance at the check hole regards the exhaust & the check hole is much smaller diameter than the fill hole. The injector tube for the 8090 oil probably won't fit the check hole.
When changing this side axel do you have to change/ take out that whole axel or can you separate just the cv axel and replace that
I understand the transfer case outflow bolt and inflow bolt, 23 minutes 45 seconds in the video.
What kind of place is tightening the video and this place is...
I wonder if there is only an inflow or no outflow.
Would I be able to just fill through the check valve until it spills instead of filling through the fill plug up top?
Can you switch fm/ Park to Neutral (to turn the wheel), if the transmission fluid is drained? I need to replace CV Axle, and want to drain before. Or if you turn the wheel w/transmission fluid off, it will damage the transmission? Thank you for the film.
wasn’t that the left side . anyways hm is that the same procedure for a nissan altima 2005?
Gratis video! Thanks
Don't laugh but how do you fill back up the call fluid than
Don't laugh but where do you or how to fill back up or at transmission axle fluid back up? Anyone? Thanks for the video!!
This is the same procedure fo a 2005?
To The differential fluid is the same?
Thank you for your help
check your owners manual, many of the nissan's (juke, rogue, murano etc) share similar fluid requirement for the diff and transfer case. If you are still not sure call up nissan parts department and ask them they will help you, i've been using them a lot for schematics and certain parts i can't trust others to provide the right part for a certain job.
Never use a pry bar on one these seals... One scratch into the casting & the new seal might fight ya going on and possibly ruin the seal. Clean clean around that seal surface. And I mean clean and use vasoline on the new seal to tap it in there... I am actually confused here at which side of the new seal goes inwards. It is shaped diff from other seals I have replaced...
Hi, do you have a video for 2009 Nissan Frontier rear axle bearing replacement?
My respect
Good Work
+William Guzman Thanks for checking us out. 1aauto.com
I have been trying to do this and it appears that I keep getting leak around the seal. Did you experience anything like this?
What’s the part number for that cv axle, all the ones I’m finding have three places to bolt, when I only have two needed
What was the sliding hammer tool called ?
Would you say it’s the same thing for an 07 nissan murano?
Just tried this. Dont know how that slide hammer did that, but maybe I just cant find the right size fork. First time in over 15 years I cant fix it and have to send it to a shop.
Good job 100%
+Corey Spence Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
was this vehicle an all wheel drive ? mine is front wheel drive so I will not need to change the fluid.
Do u need to hear a click while the axle end goes into the transmission or not?
I have been trying to do this and it appears that I keep getting leak around the seal. Did you experience anything like this?
@@coopdascoopkc yes, unfortunately I attempted this repaid and it is leaking still. The dealership wants to charge me 1000 dollars for the repair...might be the only way to insure its taken care of.
There's no identifiable audio feedback I could point to. You just have to know by feel and from eyeballing the tolerances if the CV axle seated correctly or not. It's a very uneasy feeling not having some kind of specific thing to watch for in terms of proper fitment.
Seating the seal properly and not damaging the seal are important.
That bar wasn’t even on the right way. It was doing nothing. She did exactly what your not supposed to do
Hello what the name and part # on the axle removal sliding tool, thank you
slide hammer and axle removal for fwd
Why did you remove fill plug and then fill it through the check plug ¿
i had same question, my guess is the check valve probably sits lower than the fill port does and they are using the level of the check valve as the stopping point for filling it.
She never filled this through the check plug, she verified level removing the check valve. U must have delusions
And the Murano tire tightening bolt.
What's the tightening talk?^^;
I don't understand you because you're not good at English. For these people, it would be great if you could also mark the tightening torque value in the video as a picture, and it would be very helpful if it could indicate where the inflow is, etc. and any name.
Lastly, can you tell me the product part number that I put back in the ring after removing the constant speed joint?^^;
I saw you guys used an axle fork but what size is the axle fork and do you guys sell it at 1aauto
Rotor on wrong side
I mean differential fluid.***
Ola. Parami. Meda. Mucha atlegria ber. Unadama. Aser. Muchos. Hobres. Mecanicos. Falso. Nopueden. Aser. Y son. Yorones. Para. Trabaja. Y. Ndamas. Son saca. Dinero. Agaran. Mucho. Trabajo. Y. Tada. Meses. Para. Entragarlo. Aki. En. Salinas. Ca.