God, this is so scary 😂 I’m about to do mine tomorrow and I’m watching everyone’s videos to make sure I don’t mess up. I don’t want to ruin my engine 😂!!!
looks like you're having trouble keeping the cams in position, there is a arrow that alliance to the top dead center along with the crankshaft with pistons, sometimes when the belt breaks it is a perfect tool to align the timing without having to fear of degree interference. to anyone that wants to replace valves or replace lifters do to ticking noise, don't forget to use that hand iero that comes with the engine
I think you’re supposed to set the crank 4 teeth counter clockwise to begin this process. That is what sets the pistons in the non interference position so you don’t wreck the valves when adjusting the cam gears. ruclips.net/video/OQxcHcUbOs4/видео.html
Did anytime ever find out if Thr crankshaft being at top dead center means that the valves can not touch the piston? My cam lockers came off and my cans sprung open while at TCD so I’m unsure if I’m f*****
Lenny I think you’ll be fine. I don’t think you can damage the valves or piston moving the crank by hand anyway. I’d just line the marks up and then finish your timing belt install.
How to destroy your engine… Not be sure about what you’re doing. Not have a step by step plan and checklist of what you’re doing. Not have the right tools to do it. Engine rolling around and fidgeting with camera angles. No wonder it’s scary.
@@DadbrosGarage Следующий раз лучше делать через 70000 километров (лень переводить в мили), а не через 90000 как завод предписывает. Я сам на GTO езжу - это 3000GT только для внутреннего рынка Японии. Там вообще желательно всё менять раньше предписаного пробега: Масло в двигателе через 6000км, а в акпп через 20000км.
Хороший план. Когда я купил машину, ремень ГРМ был ослаблен. Подробностей о предыдущем сервисе у меня нет. Я подумал, что лучше просто поменять время, пока двигатель не работает. Я также дал ему новую замену масла.
Just thought I would come back to this video. Thanks everyone for making it my most popular!
God, this is so scary 😂 I’m about to do mine tomorrow and I’m watching everyone’s videos to make sure I don’t mess up. I don’t want to ruin my engine 😂!!!
Did your crank bolt not get stuck?
dont think it did....i dont remember this video is 4 yrs ago lol
looks like you're having trouble keeping the cams in position, there is a arrow that alliance to the top dead center along with the crankshaft with pistons, sometimes when the belt breaks it is a perfect tool to align the timing without having to fear of degree interference. to anyone that wants to replace valves or replace lifters do to ticking noise, don't forget to use that hand iero that comes with the engine
Thank you so much this is what i needed so much detail
. you just save me $800
glad I can help
I think you’re supposed to set the crank 4 teeth counter clockwise to begin this process. That is what sets the pistons in the non interference position so you don’t wreck the valves when adjusting the cam gears. ruclips.net/video/OQxcHcUbOs4/видео.html
how do you remove the cam bolt after installing the belt?
I thought the timing mark wasn’t correct for the crankshaft it’s actually suppose to be the rolling pin attached to it?
24:33 Its the small dimple on the crank sprocket
Where can I buy a harmonic balancer for my 1991 dodge stealth 3.0l
Oreillys
What timing kit did u use
It's been so long I think maybe rockauto
Is the timing belt tensioner a one time set or can it be loosen and tighten after it's set?
One time I would think. It could jump a tooth on the cam gear
Es lo mismo para el Mitsubishi 3000gt 1992?
Sí, debería ser lo mismo
Im assuming you didnt have any valve problems after this job.
Nope thank goodness. I was concerned I would after the cam slipped on me lol
Kens Garage cool. I’ll literally in the middle of this job myself. Good to see a regular joe doing this complicated task. Thanks
@@rustyreckman2892 I read somewhere that as long as your crankshaft is at top dead center then your valves should not be able to touch the Pistons
Did anytime ever find out if Thr crankshaft being at top dead center means that the valves can not touch the piston? My cam lockers came off and my cans sprung open while at TCD so I’m unsure if I’m f*****
Lenny I think you’ll be fine. I don’t think you can damage the valves or piston moving the crank by hand anyway. I’d just line the marks up and then finish your timing belt install.
Lo puse en tiempo pero se me aflojó la correa otra vez q puede ser y la polea q va en el cigüeñal está un poco de lado
I liked your vidko one you paint your car
What book did you use
Have the Dodge Stealth maintenance book
@@DadbrosGarage thank you sir
How much u boat your 3000gt for
Bought for $1000
Awesome! Job!
Thanks!
This is a really fiddly job. I did mine without pulling the engine out.
my first time!
Looks like I missed the whole time belt removal...
There really isn't much to know
Damn
Damn
Boaring vidio but useful
How to destroy your engine…
Not be sure about what you’re doing. Not have a step by step plan and checklist of what you’re doing. Not have the right tools to do it. Engine rolling around and fidgeting with camera angles. No wonder it’s scary.
Apparently I did something right because this car is running strong even to this day
Какой же он нудный и медленный. 🤦♂️
Я не тороплюсь, чтобы сделать это правильно ... разве это не умно?
@@DadbrosGarage шестерни болтами фиксировать нужно, а не плястиковыми стяжками, вот это умно будет. Специально же есть под это дело резьбы.
@@ЛёняСветлый я ценю ваше понимание ... это был мой первый раз, когда я делал это, поэтому я уверен, что мог бы сделать что-то лучше
@@DadbrosGarage Следующий раз лучше делать через 70000 километров (лень переводить в мили), а не через 90000 как завод предписывает. Я сам на GTO езжу - это 3000GT только для внутреннего рынка Японии. Там вообще желательно всё менять раньше предписаного пробега: Масло в двигателе через 6000км, а в акпп через 20000км.
Хороший план. Когда я купил машину, ремень ГРМ был ослаблен. Подробностей о предыдущем сервисе у меня нет. Я подумал, что лучше просто поменять время, пока двигатель не работает. Я также дал ему новую замену масла.