R50 Mini Cooper Rear Strut Replacement

Поделиться
HTML-код
  • Опубликовано: 7 авг 2023
  • 2002 Mini Cooper R50 rear strut replacement procedure. My rear struts were completely gone as the car was only about an inch above my tires. When I replaced them it raised them up and soften the ride. It was like ride on coilovers the entire time I was driving the car. This was such a harsh ride. I replaced them with Meyle shocks from FCP euro.
    Parts:
    Right Rear Shocks/Struts: amzn.to/47kXTxH
    Left Rear Shocks/Struts: amzn.to/3DNe7Cc
    Bushing Kit: amzn.to/450dz7Q
    Tools:
    Coil Spring compressor: amzn.to/3qnmK3b
    Patreon: patreon.com/operationoverhaul
    Filming Gear:
    Go Pro Hero 10 Kit: amzn.to/3S9kd55
    Go Pro Endurance Battery: amzn.to/3S1KXUS
    Manfrotto Camera Tripod: amzn.to/3BnmYch
    Amazon Prime 30-day Free Trial: amzn.to/3L2iPk5
  • Авто/МотоАвто/Мото

Комментарии • 10

  • @alfredbernal8603
    @alfredbernal8603 10 месяцев назад +2

    Hello Friend
    Thank you for your time and video.
    The 21mm should torque to 103ft (140nm).

    • @operationoverhaul
      @operationoverhaul  10 месяцев назад +1

      You are welcome and thank you for the information as well.

  • @mazzapatrick
    @mazzapatrick 8 месяцев назад +1

    Thank you for sharing this video. I hope to try this on my '04 in the next couple weeks. What size allen wrench did you use here? I realize my case might be different.

    • @operationoverhaul
      @operationoverhaul  8 месяцев назад

      If I remember correctly it was a 5 or 6 mm

    • @mazzapatrick
      @mazzapatrick 8 месяцев назад

      Thank you. I just did it today. Had a problem with the bottom bolt and shock shaft nut and had to turn to others for their air tool/sawzall.@@operationoverhaul

    • @operationoverhaul
      @operationoverhaul  8 месяцев назад

      @mazzapatrick those can be stubborn and hard to remove if they have been in there a while and depending on your climate, they can be rusted as well

  • @SteveQuennell-hc2gv
    @SteveQuennell-hc2gv 6 месяцев назад

    Hi all, I notice that the triangular washer at the bottom (on the 21mm bolt) has one edge of the triangle bent inwards. What position (top, bottom etc) should this tab/bent edge be in?

    • @operationoverhaul
      @operationoverhaul  6 месяцев назад

      Most of them that I have seen are not bent. Would you be able to send me a picture of it through email?

    • @SteveQuennell-hc2gv
      @SteveQuennell-hc2gv 5 месяцев назад +1

      Aha, thanks for replying - much appreciated. After further investigation, I think the previous owner gave it an almighty whack when they hit a pothole or something (both sides had a different amount of bend!!). I flattened them out with a mallet - all good now. Thanks again for bothering to reply.@@operationoverhaul

    • @operationoverhaul
      @operationoverhaul  5 месяцев назад

      @@SteveQuennell-hc2gv your welcome