Видео

Hello Pat, Wow, has it been that long?! I can't believe it. I'll be really interested to see what you find tomorrow as I was fairly certain that retaining clip was in there very tight, so I'm stumped. Must be vibration, can be the only explanation. Please do come back Pat and let me know what you find, it may help others as well. All the best, Duncan.

Hello Rob, I'm glad it was of some help. Seems to be a common failure then, as both of the ones I've replaced failed in the same way. All the best, Duncan.

Thank you 👏

Hello Stephen, Thank you for the kind words. Unfortunately I am very far away from there, but I can tell you that it is very easy to do. Just take your time and be methodical, it will all fit out of and back in the door. This was the second one I did and both were simple enough. All the best. Duncan.

Hello, Sorry I don't have the number for it, but yours being a 1998 will be different. You can find the part numbers by going to esaabparts and selecting your model, this will give you diagrams of parts with the numbers. I had a quick check for you, but there are a few to choose from and it all depends on the chassis number. I hope this is of some help. All the best, Duncan.

You're very welcome Edgar, thank you for watching. All the best, Duncan.

Thank you, it means a lot. Glad I could be of some help. All the best, Duncan.

Hello, Thank you for watching. I had to unplug the door card to get it out of the way, I found there wasn't enough room to work around it. Also leaving it connected means it scrapes along the floor and they're not hard plastic but soft touch vinyl meaning they get damaged. All the best, Duncan.

Hello Sid, I'm pretty sure they were an option, I haven't seen them on many 9-3's. They're listed as ALU66 wheels if that means anything to you. Thank you for watching. All the best, Duncan.

Hello Hutton, Unfortunately, yes. The connector inside the reel is completely different and nobody makes a replacement for it yet. All the best, Duncan.

Hello John, apologies for the late reply I've been recovering from a spinal injury. I can see you found the pinned comment. All the best, Duncan.

Hello, Apologies for the late reply, I've been recovering from a spinal injury. I can't say that it is 100 percent, but it seems to be. The best thing to do is open the front cover of the machine and take a look at the internals, if they look the same as the one in the video then it's a yes. I hope this helps. All the best, Duncan.

Hello, I have searched for the parts manual and it looks like the Gerni 7300 is the same internally. However I would take the front panel off to make sure before ordering any parts. The parts manual can be found here gerni.com.au/wp-content/uploads/2021/09/Gerni-7300-Parts-Diagram-Ed3-Locked.pdf I hope that is of some help. All the best, Duncan.

Hello Phill, Thank you and I'm glad I could help. Sounds like you've got a nice setup now. All the best, Duncan.

A list of models that the adaptor will apparantly fit. E140.3 E145.3 E145.4 E 145 4-9 POWER X-TRA UK E 145,4-9 P X-TRA ΗΒ E 145.4-9 PA X-TRA (ΕΕ) E 145,4-9 PA X-TRA ΗΒ E 145.4-9 PAD X-TRA Η.Β E 145,4-9 POWER X-TRA E 145,4-9 PAD X-TRA E 145,4-9 X-TRA E 145.4-9 X-TRA UK E 150.2-10 H X-TRA (EU) E 150.2-10 H X-TRA GARDEN (ΕΕ) E 150.2-10 H X-TRA LUXURY CAR WASH (ΕΕ) E 150,2-10 H X-TRA ΗΒ E 150,2-10 PH X-TRA (ΕΕ) E 150,2-9 P X-TRA E 150,2-9 P X-TRA ΗΒ E 150.2-9 X-TRA EU E 150.2-9 X-TRA UK E 160.1-10 H X-TRA UK E 160.1-10 PADH X-TRA (ΕΕ) E 160.1-10 PH X-TRA (EU) E160.1-10 H X-TRA EU

Hello, Sorry for the late reply, I've been dealing with a spinal injury. It was hard to do, seeing the corrosion start was painful. All the best, Duncan.

@@FixedByDuncan I wish u the best of your health. Keep it calm you only have one back.

@@iwan-wr7gn Thank you

Hello Frankie, Sorry for the late reply, I've been dealing with a spinal injury. Thank you, I'm glad it was of some help. I do love those birds, but not on random days at 3am when they start singing. All the best, Duncan.

Hello Matt, Sorry for the late reply, I've been dealing with a spinal injury. Has the machine seen a lot of use?, if so maybe it needs new Thrust collars or pistons?. Hard to say without taking it apart to inspect for wear. I hope I have been of some help. All the best, Duncan.

Thank you kindly for your reply - it was indeed the thrust collars! Which I’ve now replaced and all working fine now. Thanks again, Matt

Hi Matt, that's great that you've got it fixed, thanks for letting me know what it was as it will be helpful for others in the future. All the best, Duncan.

Hello, Sorry for the late reply, I've been dealing with a spinal injury. I don't know the size from memory, but when I am able to do more I will measure it for you. All the best, Duncan.

Hello Phillip, sorry for the late reply, I've been dealing with a spinal injury. Sounds like a great idea for saving a few pounds. If the original length is fine for you, why go to the expense and trouble of changing. Thanks for your contribution, it will help others that maybe just want to get rid of that annoying coiling problem. All the best, Duncan.

Hello, Sorry for the late reply, I've been dealing with a spinal injury. I'm glad I could be of some help, thank you for watching. All the best, Duncan.

Hello Pierre, Sorry for the late reply, I've been dealing with a spinal injury. I'm so glad to have been of some help. All the best, Duncan.

Hello, Sorry for the late reply. What is the exact model number of your machine?. Alternatively, you could remove the front cover. It is very easy to remove, only a couple of screws. If it looks the same as the one in the video on the inside, then it can be done. All the best, Duncan.

Nilfisk e145. 4

Was try to replace hose with quality one from qwashers???

Hello, If you have a look at this PDF www.google.com/url?sa=i&url=https%3A%2F%2Fnorthwestpowerwashers.co.uk%2Fwp-content%2Fuploads%2F2020%2F01%2FE140.3-Repair-manual.pdf&psig=AOvVaw1fdBA2wjv9pYXMMJ71pPYp&ust=1664962096730000&source=images&cd=vfe&ved=0CA0QjhxqFwoTCOClsamhxvoCFQAAAAAdAAAAABBA On page 12 there is an image ( Fig 11 ) of the machine open at the front, if your machine has that brass coloured pipe then you can use the adapter to add a new hose and bypass the hose reel. It does seem that E145.4 is the same internally from the documents I can find, but it would be wise to open it and have a quick look just to be certain. I hope this is of some help. All the best, Duncan.

Hello, Sorry for the late reply. I'm afraid it's not possible to use the hose as a drain cleaner, it wouldn't have enough pressure without the gun. There is a special drain cleaning hose available, this attaches to the gun and works very well. All the best, Duncan.

Hello, Sorry for the late reply. How did you get on with it?. I found my machine to be much more useful after doing this upgrade, wish I had done it sooner. All the best, Duncan.

I actually got the hose delivered before the adapter so I just unplugged the lance then added the new hose in tandem and plugged the lance into the end of the new hose, leaving the old hose in situ on the reel. It seems to work fine when cleaning the car so I'm not going to bypass the pld hose and fit the adapter yet as when I wash the patio the old hose will give me an extra 10m which will comevin useful

Hello Adrian, I did consider doing that, but as I went with the 20 meter hose thought it may cause me to lose too much pressure. Just out of curiosity, what length hose did you go for?. All the best, Duncan.

Hi Duncan, I wanted the 15m hose but it was out of stock so went with the 10m one in the end so effectively have the same length hose as you now (The original 10m plastic supposedly anti kink one with the new 10m reinforced one attached to that) I managed to get the adapter too which I haven't fitted yet so will see how I get on with my existing setup but could always swap to a longer hose later. Once again thanks for doing this video as the original hose has been driving me mad ever since I got my jetwash. Cheers Ade

Hello Aaron, Sorry for the late reply. Have you managed to sort this now?. Water pulsing is usually low water pressure on the supply side, or a slow loss of pressure on the outlet side. Perhaps have a quick check of o-rings to see if any are damaged?. I hope this is of some help. All the best, Duncan.

Hello, Sorry for the late reply. If you can hear a grinding, it is because the cable has moved on the roller and has been grinding them to pieces. It is not really possible to replace them as the cables are usually damaged as well. You stated you've already got the regulator, so probably best to put that in rather than mess with the rollers. You've probably already completed it by now, but best of luck if you haven't. All the best, Duncan.

@@FixedByDuncan Thanks. I just got the part a couple of days ago and will try it this weekend. Thanks for the guide!

Hello Turk, Is it the motor that doesn't work, or is it the mechanism that's broken?. Can you see if it's possible to cut the wire rope that the motor uses to move the runners up and down?. Make sure you secure the glass up top with some tape so it doesn't drop, or get another pair of hands to help you. You will need to have a replacement mechanism ready to fit as this will obviously destroy it. After cutting, you should be able to move the glass up and down by hand ( just watch your fingers ). I hope this is of some help. All the best, Duncan.

@@FixedByDuncan Thanks Duncan Your advice is appreciated. Have day off tomorrow And will try it. Thank you

@@theturk3874 You're welcome, let me know how it goes. All the best, Duncan.

​@@theturk3874 Take the switch apart and wash it with alcohol and a toothbrush its common for the board to corrode where the contact happends on the board. In my case it needed some scraping as well.

Hello Laurence, I used this hose from Direct hoses: www.directhoses.net/collections/hoses-for-nilfisk-alto-pressure-washers/products/nilfisk-style-rubber-longlife-extension-hose-for-hose-e-series-reel-models It has the fittings ready to attach to the modified outlet and can still be used with your Nilfisk gun. I hope this helps. All the best, Duncan.

Hello, Yes, the non return valve is listed as being inside the opening where I placed the new fitting in this video. I have a parts manual I can email you if that would help?. All the best, Duncan.

Hello, The only place that I have ever seen selling it in the UK is here northwestpowerwashers.co.uk/product/nilfisk-outlet-insert-quick-coupling-128500622/ There are suppliers in Europe, but I couldn't get any of them to ship here. Have you opened your machine to check it will fit?, I would recommend doing so before ordering as some look the same due to the casing but are different inside. I hope this helps. All the best, Duncan.

Hello Jack, I completely agree!, fantastic tool. I couldn't be without it now. All the best, Duncan.

Hello, Apologies for the delay in replying, I have been incredibly busy lately. This is for the four beep error with red light indicating a brushbar requiring too much current to rotate it. This can be caused by the motor spindle becoming clogged as in this video, or the actual brushbar getting jammed with hair. I have a follow up video that shows how to resolve the brushbar getting jammed. Once again, my apologies for not responding sooner. I hope this is of some help. All the best, Duncan.

Hello Aqualtislad, Sorry for the delay in replying, been incredibly busy. I hope your repair goes smoothly, saves another appliance going to landfill. All the best, Duncan.

@@FixedByDuncan yeah so it’s been fixed :)

@@Hwash500-t18 Excellent , glad to hear it. 👍🏻 All the best, Duncan.

@@FixedByDuncan it’s broken again 😡

@@FixedByDuncan it’s making a REALLY loud noise on spin

Hello Tim, With regards to a clunk, is it multiple or single?, does the window go up and down?. If multiple, I would take the mechanism out and look at the gear on the motor and the socket it goes in. Next port of call would be the rollers as you suspected, they can disintegrate causing the wire to wrap around and jump. Is the glass secure in the grip?, perhaps it is dropping when in operation?. Ultimately, the easiest way to see is to remove the mechanism. Can you source one from a breakers yard or Ebay?, they are fairly cheap. I hope this is of some help, All the best, Duncan.

1.电机问题 2.导轨问题

Hello, Thank you for the kind words, they mean a lot. I'm glad I could help, I'm sure you'll love your new AVA. All the best, Duncan.

Hello, Sorry for the delay in replying, I've been so busy lately. I'm so happy I could help, brings a smile to my face. All the best, Duncan.

Hello, The benefits are mostly a hose that doesn't kink, coil up and rub itself along the paintwork of your car. Also, the hose length makes your power washer much more versatile and more pleasant to use. There is also the fact that you can take your pick from not only Nilfisk attachments but also standard quick release attachments ( under chassis washers, extra long lances, generic drain cleaners etc ). I hope this helps, All the best, Duncan.

Hello Ratspeed Garage, Oh no, that's not good. Seems to be still in stock in Sweden, but not UK. I wonder if they don't want people doing this mod?. It doesn't look like it would be hard to replicate the part from a brass bar on a lathe, hopefully someone can come up with a solution if this part is not available anymore. All the best, Duncan.

@@FixedByDuncan Hi, I ordered the the adapter in Jan 2022 from Northwest as per Duncans advice. I was assured the item would be in stock approx early March on back order from China! I searched every where and managed to track down to Sweden and Holland. I emailed both companies but unfortunately due to Brexit they no longer supply to UK. *Northwest had offered me a refund if I found another supplier. 👍 The part arrived last week! I can highly recommend Northwest power washers. Excellent advice and very friendly staff!

25 Feb 2022. Just checked. 1 Adapter in stock!

Hello Patrick, That's great news, glad you managed to find one. I had the same problem when trying to buy one from suppliers in europe, all said no due to brexit. I can also wholeheartedly recommend northwest power washers, excellent service. Thank you for letting us know. All the best, Duncan.

Where can i find the adapter? Webside please:)

Glad I could help :)

Thank you my darling daughter :)

Hello Ryan, I'm glad I could be of some help. All the best, Duncan.

Hello Patrick, Yes, it is possible to remove the hose from the reel completely. There is a wire clip that can be pulled to release the hose from inside the reel, if you unwind the hose completely you should be able to see it. cdn.shopify.com/s/files/1/0208/7184/products/QRChosereelconnectionstraight_4032x.jpg?v=1611329563 Have you removed the front panel to have a look at the housing inside to see if it matches?, this would probably be my first move. I will try and find a service manual for your model and link it here tomorrow. The quick release on the new hose is Nilfisk quick release and not universal, it fits nilfisk guns on one end and fits the quick release hose on the other end. The new gun has a Nilfisk pattern quick release, meaning it could be used with an original Nilfisk hose or the new hose. This is how I purchased it. www.directhoses.net/products/nilfisk-c-series-quick-fit-short-trigger-with-quick-fit-nozzles When you remove the hose from your reel, be sure to take a look at the end that comes out. Some models have a fitting that has been replicated and is therefore much easier to replace with a high quality hose. One of these: www.directhoses.net/collections/hoses-for-nilfisk-alto-pressure-washers/products/nilfisk-style-replacment-hose-quick-fit-trigger-hose-reel-connection If your hose has the straight connector like this one, then you can just replace your old hose with this one. www.cleanstore.co.uk/images/large/13049a.JPG If your hose has a cranked or bent connector like this, then you can't. brownspressurewashers.co.uk/wp-content/uploads/2018/02/9m-E140.3.jpg The difference can be seen in this image imgur.com/DY75o3I I hope I have been of some help. All the Best, Duncan.

Hello Patrick, This parts list is for a d140.2 and it appears to have the same housing as mine, probably still worth taking a look inside though. www.google.com/url?sa=i&url=http%3A%2F%2Fwww2.mersch-reinigungstechnik.de%2Fmedia%2F696%2F116578_b1b00c0c64804e8f8cd07cee4b70a32e.pdf&psig=AOvVaw1jGSxHz3_XiegxjozcquyP&ust=1642194489198000&source=images&cd=vfe&ved=0CAwQjhxqFwoTCLCfvavRr_UCFQAAAAAdAAAAABAe Page 4 is the relevant one. All the best, Duncan.

@@FixedByDuncan Thanks Duncan for your prompt and comprehensive reply. I will read and digest tomorrow.

Hello, That's excellent, I'm just glad I could help someone. It's definitely made it into a different machine. Thank you for the kind words. All the best, Duncan.

Hello Athina, I'm glad you liked it, thank you for the kind words. All the best, Duncan.

Hello Athina, Thank you, and she is a great helper. She was over the moon with her new room. All the best, Duncan.

Hello Alfred, I'm glad I could be of some help. Thank you for watching. All the best, Duncan.