Видео

To warm up my car in winter, i let the window defroster and then cabin heater run for about 10 minutes or until air flow comes out warm. The heater keeps the engine running and help's with warming up the fluids on both engine and transmission.

what seal kit this you buy I have ZF 32136759815 input shaft leaking

Does the 68ohms, 5w resistor I keep the climate control and energy system showing on screen?? Cuz I install double din I lost both

Hi buddy. I’m confused become my small screen that came with the car says check connection to the ac. Steering wheel controls work for a/c. Auto and tamp.

If your wire welder is feeding crappy you can try blowing some air through the liner in the whip. Lots of times it will become filled with a dusty residue and cause feeding problems, in my experience. Good video.

Thank you it was really helpful

U made it worse

What do up set your tire pressure to?

engine and transmission ☠️ this vid isb2 years old and I bet u already scrapped this car

Thank you!

I removed the + terminal first and made a short circuit :(

For up-to-date info on the project, you can check out the build thread at E46 Fanatics. www.e46fanatics.com/threads/build-thread-the-basket-case-bmw-project.1284565/

The filter collapsed tells me neglect, the oil color is like mine after 5500.

Mostly because people are ignorant, lazy or cheap. Or any combination....

Thanks!

Would an issue with lower control arms cause the car to pull right then go center then pull left and repeat? Even after an alignment

Buy a new one. It comes pre pinned. You're taking a chance at damaging it and will have to do the job all over again. How much is your time and engine worth? This is stupid.

the hydraulic tension can be damaged easily when not tensioned correctly and can cause it to lock up pretty much making it no good anymore i had damaged a few before learning how to use those. i always use mechanical tensioners from now on lol

Careful that puppy doesn't pop out and learn ya a lesson...put a guard around or have great reflexes.

Sweet! Lifetime warranty EMP Stewart water pump w/metal impeller?

For up-to-date info on the project, you can check out the build thread on E46 Fanatics. www.e46fanatics.com/threads/build-thread-the-basket-case-bmw-project.1284565/

Finally made a pair. Good stuff. Recommend drilling through both legs at the same time to ensure a balanced fit.

how did you get the shifts that crisp and fast on the stock TCU? Is it just upgrading the boost valve? can I do the same on a ZF A5S325Z? Where can I get these parts?

Hi, it's a good lesson, but I bought a radio instead of a standard climate-controlled display. So I don't know how to connect climate control to work., any ideas?

Where did you tap in for the oil pressure gauge? I'm interested in installing one aswell.

If you haven't seen the transmission build video, here's a link. ruclips.net/video/znFoPWzU00k/видео.html

Is that where all the fluid comes from on the downstream hoses?

You must use Liqui moly transmission oil 30ml pack, not ceratec, even if your car don't have a clutch

If it works and you saved money, nothing more to be said.

👍👍🛞💨

I had to order 4 condensers because they weren't packed well and the shipping service loves to throw boxes around. Just finished a coolant refresh and also replaced ccv system and disa as well as vacuum lines

Ac delete!?

Guibo! Best part name ever.😂

Hello sir. Would the torque specs be the same for a 2010 beetle 2.5 since the bushings are also 23 mm and what are the torque specs for the end links? Does it vary from top to bottom 🤔.

The radiator fan saga is complete! Now I can move on to bigger and better things.

Your biggest mistake was buying a bmw😂

How is the review after using it to engine? Pls reply i also wanna use it

You will find out if that one burns out

Should’ve replaced the fan motor too, it could be pulling too many amps which is why the controller melted

Ok. Did you save money and or have fun doing it. If the answer is YES on either of them then yes it was worth it.

germayn here. Our product is not about fuel economy, Its about less friction and damage to the motor ! also it runs more smoothly, less rattling, overall.

Youre blacktree on pff, right??

Or just replace it all since its already apart.

Hahaha safety squint

I wonder what the controller actually does. I was thinking just putting power to the leads wouldn't work. I would think with the module. They would be using a 3ph brushless motor. Kinda how they do drills. Usually there is a ring that tells the module what phase it is in. And it can track the rpm. Then adjust the speed in this case by temperature, speed, or ECU command.

When you replaced the digitizer was the sun damage fixed, even though you had other damage to the lcd?

Thank you for your good video! 6:04 How did you replace a wire cowl(or room)? Are there any parts number?