How to rebuild Fuller 18 speed transmission
HTML-код
- Опубликовано: 3 ноя 2013
- Rebuilding a Fuller 18 speed transmission. This is a short video showing off what it takes to completely rebuild a Fuller transmission back to original working standard that meets or exceeds the manufacturer's. We rebuild all heavy duty transmissions from all brands such as Eaton, Dana, Spicer, Rockwell, Meritor, ZF and many more, so if you have a question or need our services, please give us a call at 1-877-776-4600 or visit our website at www.progearandtransmission.com
Авто/Мото
amazing how the countershafts were laid in and as if by magic the main and counters were suddenly all set up ,coool
I agree. Lol
@@CosgroveNotts stupid title for a video..should have called it watch magically how a transmission rebuilds itself.
you guys do good work the video was not to show how ,,,,look forward to meeting you and dan bringing mine down from tn because of the quality work and getting it done right ,,
very nice. much respect to the builder.
As a DAF mecanic, I can tell you,
he is not showing his secrets.
He is not crazie, he will do it for you.
Thats his job.
As a daf mechanic I don't miss these on the daf 2800 and 2600
@@CosgroveNotts what is a daf mechanic
DAF is a British Cab-Over-Engine truck make like Volvo.
All these negative comments by Johnny Honeowers wanting to rebuild their 13s in a garage.
Timing? Bearings?
Learn your limitations. Drop the Damn thing off at this dude's shop or open your own shop.
Great video showing how complex the operation is.
HEY!! You did a good job body thanks for showed this video GOD bless you
Watch those fingers! Looks good cleaned up and I'm pretty sure the PTO was the leading reason this trans went south to begin with. Nice advertisement for the shop.
MrRingo359 why do u think that
2:04 OUCH!! crushed fingers.
It's almost been what 4 years since I've build one miss doing this stuff
Orange paint adds a couple of horsepower.
Goodness-this was interesting even if only for the fact that we haven't seen this kind of Transmission in Europe for at least 25 years..
Now that's precision engineering
how does it work....especially on high/low range & splitter???
If this guy is a good teacher I’m the king of England
that music doesn't just suck it really really sucks
i couldn't have said it better..........
Honestly, it depicts the purpose of the video if u only show the part everyone can do.
ok, I have to say this. 2:54 the gears are not seen and 2:56 all gear are installed? Why did you cut that important final gear assembly out?
i can improve your assembly times with a few tricks of what you did show. nice cleanup and paint job.
Post a full vid of an eaton 18sp rebuild if u haven't
If driving doesnt pan out for me Id love to build these big transmissions.😀
I been doing the same thing for years this guy is actually doing it wrong
Disculpen mandé ajustar la transferencia de la 18 pero la pusimos y no entran las altas alguien me puede decir ya cambie el módulo del cambio y sigue igual
Do us a favor, on your next video please leave out the Disco drum music. Do you really think people with an overhaul on the mind want to listen to this?
Turn off the volume, problem solved
He does? And isn’t he doing the same thing?
Muy Bueno Gracias por compartir,,
Trasmisión 169-18 👌
como faz pra pôr no ponto as engrenagens?
Great video, glad my mute button works!
Video hay quá bác
well, that looks like a good build. but where is your shop located so I can bring my truck? your website just says to call, and offers no specifics as to price, location or diagnosis of minor repairs or a full rebuild. how am I supposed to know what's exactly wrong with my 18 speed?
Liked it
Muito bom,só faltou mostrar como montar o conjunto Central ou conjunto de engrenagem móvel
I wonder how they get so clean
En mexico se ajustan los trenes latrales de la trasmicion auxiliar por ke aki no se be el ajuste
Why doesn't Eaton use syncromesh (brass rings)?
Ya I was watching but miss the part about timing it ?
I honestly thought an Eaton-Fuller transmission would be bigger than that - it looks like a very space-efficient design though.
What are the yellow position marks on the gears for? Do they need to mesh at a specific point to make sure everything else meshes properly?
Timing
Yes the countershafts have to be in time with the main drive gear.
3:45 banged up gasket
Boa noite meus amigos que estão ai juntos neste momento maravilhoso e eu vou ter um imenso prazer em compartilhar com todos vocês. Um abraço e que Deus abençoe a todos.
lol that top counter shaft is a little hard to get in with the pump gear installed ,but I have a tool for that :)
Not seen or worked on one of these for 30 years thank goodness. Much prefer ZF AS tronic. Fit and forget and no clutch replacing either. Let's have an easy life instead of rolling about on the floor messing with primitive gearboxes, clutches and that stupid stick thing with 5/32 air pipes.
Glad we've moved on.
Music is so knowing
l have problems with the splitter on my 18 speed l can go hi to low and vice versa but I can't split the gears to get the full 18
any suggestions on what the problem could be thank you.
Take a look at the synchronizer in aux housing. Could be worn or damaged.
Columbus Christopher the splitter sliding clutch is worn out. That would be my guess
Nice trans.
Third circle in hell for the sound engineer.
Thumbahs down da da da da click click bada brrrr pip pip.
deadly and good
Male video no Elena nada
To bad that's a 13 speed I can tell by the air system 18 speeds don't have a 5/32 air fitting on the high side hose of the a-5000 valve. And he built that the hard way
Spanky Roberts Right it so much easier to build it with the input shafts down . You don't run the risk of the counter shafts falling on your fingers.
That's not an 18 speed. It's a 13. Look at the shop knob, and you didn't even show how to build the main shaft, installing the roller beatings, timing it, or building the rear section. So you really didn't show a damn thing on how to rebuild.
That's so true he didn't even show any one how to time it
porque no pasas el armado completo
you didnt even show anything, you skipped most of it.
What do you expect in 7 minutes?
@@joeyboland3406 true,,,,,,,,,,,so then the video was a waste of time......not impressed at all.
@@yardlimit8695 yes it was a waste of time. There is no point in putting together a 7 minute Fuller 18 rebuild video, unless you are just jam packing all of the important information (which obviously was not the idea here)
oh come on, it showed him fighting a counter shaft and it showed him fighting the aux trans, lol
i came here for the good beats!!!!!
How about the 3 hour struggle with the main shaft and circus music ? lol
2:03 ouch, that hurts ;)
Creepyguywithphone1324 haha!!
Whats cost
شكرا
This video showed me how badly I don’t want to go to work on Monday cause I do this shit for a living and you skipped everything watching this vid sounds like I’m walking threw a strip club
As a 47 yr's trucker/mechanic, I have no fucking idea what the point of this video was !! %$*&@$#% 😡
art
This isn't a how to video, it's a video of you doing some work with some lame music. A how to video is when you are explaining how to do something.
If you don’t time your gears right it will chew itself apart but quick!
My hands hurt watching it
Shouldn't say how to rebuild in title, should say this is what it looks like lol
I don't think this was his first one , not even his first one that day.
signal44
De Huynh
2.07 AUW... !!! Fuck..... I know how it feels.
I wonder how this guys still has his fingers...
16 speed zf acosplit the very best.i drive one m.a.n. f2000 truck.zf trans rebuild 1600000km...100000miles...but not pull just 46000 lbs!pull 78000lbs load weight!
Pra começar ,uma amassada nos dedos ,pra ficar esperto
buen video amigo!! aprovecho para decirte que te pases por mi canal salu2 :)
That wasn't a rebuild video. It was a bits and pieces assembly video
We’re all the gears replaced in the transmission
if i worked there all my fingernails would either be black and blue or gone, how that guy drops then countershafts in without sacrificing his fingers at the first knuckle is beyond me
lo más entretenido fue cuando te apretarse los dedos.....y gracias por mostrar la puesta apuntó...poco educativo te pasaste 💅
Fuck that gasket i guess
You skipped the annoying part of putting in/timing the mainshaft.
好
This is a different way of building an RTLO**913A transmission. I personally don't prefer to build them on end. The rookie mistakes in this video though 🤣
Ancient engineering. You don't strip gearboxes anymore and no one uses fuller. Is this Murica and still in the flower power era?
cosgrove notts if they don't use Fuller, who do they use??
Can’t understand why people think they need to put music in videos. Hell, even MTV don’t do that anymore.
the porn music jajajaja
now if he was listening to some speed metal he could have done it even faster
thats a 13
+Carla Wilkinson Yep, you are correct, the high side main line (the big black line)., is "T'ed", 18 speed is not. I didn't see a good pic. of the aux. splitter gear but an 18 has a bearing and a 13 has a washer set up.
2:08 walk off..
Not really a "how to" if you don't explain anything and put music over the whole video
RIGHT,,,,,,,,,,,so why bother watching this junk if you can't learn something.
This fuckin' music!!! 🤣🤣🤣
🤣🤣🤣
Solo mete las piñas no explica cómo armarla paso a paso voló el mexicano el di dises paso por paso un maestro si yo entiendo que no le da tiempo por que es poco en el video pero que tiene se hacen tres videos
Looks like a two man job to me.
ok "
Hi
he squeeze is fingers ha ha ha the shop look dirty
yes it is
Pinches his finger and has to step away.
missed a lot nof sreps
2 counter shafts one man
Very bad video because it is not shown when the transmission is synchronized
This video is not a "How To Rebuild", more like "Watch me rebuild without instructions with russian music"
WTF does ANYBODY go through the trouble of making a potentially informative video and totally SCREW IT UP by adding needless background NOISE?
Annoying background noise prevents me from giving a thumbs up.
The seeing a rebuild keeps me from giving a thumbs down.
The music is annoying!!!
mal video no explicas como sincronisas los piñones de un solo saltas a armarla mal maestro
pinched your fingers didn't you?
Shouldn’t say how to... lol should say watch me build a 13 speed
For a peterbuilt even lol
you missed all the good stuff and the swearing, I'm guess that is the reason for the stupid music.
Music sucks
Hack
Not a very good video for how to put a f****** transmission together
What is this music? Wanna be deep house? smh.
Cut the stupid music
you skipped some steps...if your going to make a video do it right!!