Install Input Shaft on Eaton Fuller Transmission - I Wish I didn't need to open up the top cover 😢

I am showing you step by step how to install an input shaft on Eaton Fuller Transmission 16909 (9 speed convertible to 13 speed). The top cover is totally rusted out. I was trying to avoid opening up the top cover. However, I ended up opening it.
How to Remove Input Shaft on Transmission - Step by Step
► • How to Remove Input Sh...
You can get the same input shaft bearing puller tool here: amzn.to/3XMON7m
📢Exciting News:
Our online store is officially launched - Shop the largest collection of DPF, DOC, SCR & One Box at a price you will like!
► DPFDiscounter.com
Business Info:
FTT Fleet Solutions - Fleet Solutions to Help Fleets to Run Smarter & Save Bigger)
► Address: 1120 High Ave SW Canton, Ohio 44707
► Phone: [phone] (for business only)
► Email: [e-mail]
► Diesel Emissions Specialists (DPF Cleaning, Aftertreatment Emission Diagnostic & Repair)
maps.app.goo.gl/qUCbctm6ZCxF6...
► Diesel Force Cleaning - clean the entire engine
fttfleet.com/pages/diesel-mai...
► Best engine and aftertreatment warranty you should have - NTP warranty
fttfleet.com/pages/ntp-warranty
► Remote diagnostic - remote regen and clear faults while your truck is thousands of miles away
fttfleet.com/pages/software-s...
► Polar Fox eAPU - The most advanced and affordable electric APU for trucks
www.polarfoxapu.com/
Shop the largest collection of DPF, DOC, SCR & One Box at a price you will like!
► DPFDiscounter.com
Connect with us on Social Media Platforms:
► RUclips: bit.ly/35YO3kN
► Instagram: bit.ly/3C7hRy6
► TikTok: bit.ly/3QxGHMT
► Facebook Page: bit.ly/2QqBuZ0
► Threads: bit.ly/3KmNp6P
► Trucking Facebook Group: bit.ly/34TbQXQ
My Favorite Products for trucking & truck repair needs from Amazon:
► amzn.to/3xZkDn3
Awesome Products and Services We Recommend:
► OTR performance diagnostic tool (super easy scan tool every trucker needs) - use promo code road3333 to get $100 off: bit.ly/3O3wshT
► Rock Rooster offers the best work boots for you. Use channel-exclusive promo code road3333 to get 12% off of your order today. bit.ly/3HFLFDu
Want to work with our channel? Email us for more details
[e-mail]
-----Disclaimer-----
The information and instructions provided by Trucking & Fixing with Ryan RUclips channel is for general informational purposes only. All information on the channel is provided in good faith, however, we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability, or completeness of any information on this channel. Some product links are affiliate links which means if you buy something we'll receive a small commission.

[@truckingandfixing]

Connect with me on Instagram: ►

[@mgakowski]

Anytime you remove the shift bar housing you need to remove the hi low slave bro. Sometimes that interlock pin doesn't come out with it either, just make sure it's out the way before you refit the cover, then you refit the slave/pin.

[@banzaii6285]

Love the longer repair vids, but....I know you're trying to run a business (not a school), and it's probably a pain to record. Thanks👍.

[@eddiebartholomew9172]

Never seen someone install input shaft retainer without silicone

[@josevaldez7281]

That dodge @

[@rickysons6362]

Just wanted to know if pdi turner worth getting

[@BoostedOnaBudget5]

I hold and pull the shaft towards me while sending the bearing in with a hammer or mallet till you can see the indentation for the snap ring

[@edwardreyes6867]

When the bearing is seated and the input shaft is too far in and the snap ring groove is covered like that, I smack the input shaft with my palms side to side and it’ll work the input shaft and bearing out a bit so I can give the installer tool some more hits. Repeat a couple times and it’ll drive it in properly. Wont have to remove the top cover.

[@BoostedOnaBudget5]

Send it with the rubber mallet that top cover did not have to come off!

[@eddiebartholomew9172]

Lmao why did you install input shaft you can see the hub for overdrive and main drive gear is rolled to death gonna be jumping out of gear. It’s need to be rebuilt.

[@xlxyetixlx]

a cheap needle scaler from the usual scum bags would make quick work of cleaning the dirt and rust off the top cover then just blow it off

[@BoostedOnaBudget5]

That installer wasn't it lol