Krystal -- In the video I initially connected the Halo projector light WHITE wire (Power source cable) to the Car's RED wire. The Red Wire is HIGH BEAM LIGHTS -- so if you turn on your lights the LED lights won't turn on, until you TURN ON the HIGH BEAM lights your bright lights. Later, After the video was made, I decided to connect the HALO projector WHITE wire to the Car's VIOLET wire- that is the LOW BEAMS this way I could show off my Halo LED lights without having to go to switch to the Bright Lights all the time. This way when you turn on the Low Beams The L.E.D lights come on. Connecting the Halo Projector white wire connection to the Car's Violet LOW BEAM wire - will give you this result: (if you are standing in front of your car lights) the right smaller light and Halo and LED lights will come on. When you switch to bright lights -Only the Left bigger light and Halo will come on - No LED LIGHT or smaller Halo will come on. Hope this helps. Yea I found this weird too. I just lived with it. As far as "one is brighter than the other"... check your White wire connection in the step where you had to strip some of the plastic casing to reveal wire -- make sure you did not cut pass the plastic and cut into the wire and thinned out the wire. Also check to make sure all white wires are held tightly in the Crimp Connector --there is a possibility that that are loose or they have been stripped too thin and not enough power is running through them because of thinned out wires.. Hope this helps.. (Not sure why the LINES are going through my sentences... Disregard those lines)
Авто/Мото
![How To Install Retrofit Projectors With Bi-Xenon [10 Steps]](/img/1.gif)
best video out of all of them thanks allot!!!
Great video ! Helped me install halo headlights in my car while I followed you're video step by step
Would the same procedure work for a 2003 dodge neon? I just bought the halo lights for my car, and I haven't installed them yet. But will do it soon.
Yes will work on 2003 dodge. Sorry about my toe nails... HAHA, I did not realize they where that long..haha..
i have a 2002 neon would the plugs fit for a 2003 headlight?
Es el mismo procedimiento para un eclipse 2003
I did exactly what u did on your video and lights come on but not the halo part and on is brighter then the other. What could it be?
Krystal -- In the video I initially connected the Halo projector light WHITE wire (Power source cable) to the Car's RED wire. The Red Wire is HIGH BEAM LIGHTS -- so if you turn on your lights the LED lights won't turn on, until you TURN ON the HIGH BEAM lights your bright lights. Later, After the video was made, I decided to connect the HALO projector WHITE wire to the Car's VIOLET wire- that is the LOW BEAMS this way I could show off my Halo LED lights without having to go to switch to the Bright Lights all the time. This way when you turn on the Low Beams The L.E.D lights come on. Connecting the Halo Projector white wire connection to the Car's Violet LOW BEAM wire - will give you this result: (if you are standing in front of your car lights) the right smaller light and Halo and LED lights will come on. When you switch to bright lights -Only the Left bigger light and Halo will come on - No LED LIGHT or smaller Halo will come on. Hope this helps. Yea I found this weird too. I just lived with it. As far as "one is brighter than the other"... check your White wire connection in the step where you had to strip some of the plastic casing to reveal wire -- make sure you did not cut pass the plastic and cut into the wire and thinned out the wire. Also check to make sure all white wires are held tightly in the Crimp Connector --there is a possibility that that are loose or they have been stripped too thin and not enough power is running through them because of thinned out wires.. Hope this helps.. (Not sure why the LINES are going through my sentences... Disregard those lines)
Thanks so much
what size wire you use??
+John Tenelema 16 AWG 7.62 M