REMOVING ROUNDED OFF NUTS & BOLTS WITH A TWIST SOCKET SET!!
HTML-код
- Опубликовано: 25 апр 2019
- This Blue Point Twist Socket set has been fantastic for removing rounded off fasteners and studs and is so easy to use!
Twist Socket Sets:
"Maximum Impact" Twist Socket Set - amzn.to/2ZCknqU
Blue Point Set In this Video: store.snapon.com/Twist-Shallo...
If your ever looking for more tools to get started or add to your collection check out the page on our website for great recommendations - www.gearheads-garage.com/tools/
We appreciate your support to keep GearHeads going!
Visit store on our website or support us through Patreon!
www.patreon.com/gearheads
www.gearheads-garage.com
Subscribe For More Gearheads, and Follow Us On Social Media!
Instagram - @Gearheads_Garage_Cam
Twitter - @GH_Garage
Snapchat - @gearheadsgarage 
Авто/Мото
Always great to hear young newbies talk about stuff I went through over 40 yrs ago. Glad the tools have gotten better.
ive seen em, always wonderd if they worked, guess they do! Now officially on the bucketlist of stuff to get.
Absolutely great addition to a home mechanic tool box when you have lots of old vehicles. Purchased my set of good quality (most importantly) for $99 .
Thank you very much GearHeads...I used that kind of fastener just as you described and finally removed my drain plug. Thanks again
Thank you. This worked perfectly. You saved me ton of time and money.
Awesome, thanks a lot for the tips. I actually am in the middle of dealing with trying to remove a rusty bolt with a rounded off head so this was perfect timing.
Love when the timing works out like that!
Same!!
Excellent video. Spent an hour trying to remove couple rounded bolts from a 4runner skid plate to get to the oil filter. Watched your video, went to Harbor Freight and picked up a bolt extractor set..... job done in a couple minutes. Thank you!
I have the harbor freight set and they are great but they don’t twist on so they don’t always work as well as these Irwin’s do.
Should of used pipe wrench if u dont have these sockets
I just wanted to say thanks for your knowledge and how the tool works. Look forward to the next video.
Great Video is very honest and real! Living in Ontario We encounter rusted fasteners all the time Some of them have never been touched but are completely eroded away! A video suggestion for you would be to build on this content with a video on all the options for rusted fasteners especially exhaust. We have accumulated a great collection we have the twist sockets shallow and deep up to 1/2 dr a shorty craftsman socket set that works in confined space, a set of twist wrenches, and fit it goes sideways left-hand drills, Alden drill outs, and regular extractors Your right about the comment about forgetting about them until you need it and we made these a shop purchase so we could buy them all. Like you, even with shop purchases, we are very careful to get the best tool for the money and don't shop on the truck very often However your comment about replacing dull sockets on warranty got my attention! Sorry to make this so long I really enjoy your work and am new to your channel keep up the good work! Thanks, Ps Those induction bolt heaters look very effective still need the twist sockets but why not get them ready to come out if you can! On our never-ending list of tools to buy! Thanks Jeff
Very good channel. Good in depth tool reviews. You gained a sub!
Hi Jesse at GearHeads: Thanks so much for the very useful and informative instructional video on using a twist socket set. Last night I went to replace the mower blades on a pre-owned John Deere L100 lawn tractor. Two blades utilizing four bolts. With a little effort the first blade came off, but the two bolts holding the second blade will not budge, even when I sprayed in white-lithium grease. Then one of the bolts started rounding off. So tomorrow, Saturday, I'm headed to a local tool store to buy me a twist socket set. Again, thanks for sharing your know-how and experience with us amateur mechanics. Jeff in rural Aylett, Virginia.
Thank you and good luck Jeff!
Yep these are worth it. I have a set and they have saved me a few times.
these worked for me. a 10mm bolt head was stripped, and the 3/8in. size socket took it right off.
Thanks for testing there, have seen them but never knew if they were any good? Like all your videos.
Thanks ! Yes 👍🏼 !! Very nice tool - it worked for me on a factory mushroom round top bolt rusted in on 15 year old Canadian wheel carrier / knuckle . The inside torx 50 receivers had stripped out . Put this on an it was out in 5 seconds .
Best way not to round off bolts don't use 12 point sockets on 6 point bolts.
Shimon trust me I leant my lesson
@@itsraheem we all have lol.
What's the point of a 12 point socket anyways?
@@isaacc3307 Well, not often, but in a tight spot, too much degree movement with a ratchet, only a t handle or breaker bar will work to get some motion, and a 6 point doesn't even allow enough rotation to accomodate putting it at the right angle. Like I say , very rare, but after 45 yrs of wrenching, yea ran into this plenty of times.
@@treeguyable oh so a 12 point just gives u a better angle that a 6 point won't allow for on rare occasion? Is this what a 12 points purpose is?
I use the Irwin "Bolt Out" sets. They also have deep sockets for removing nuts from long studs (I'm sure Snap On does too). The Irwin sets are priced under $50 each and have never failed me. They're also much easier to find than Snap On.
Thanks for the tip dude. Went to go change gf's oil in her truck and whoever she took it to last- cranked down the plug and rounded it off, so hoping these will do the job!
SnapOn also makes the best Fitting wrenches for working on hydraulic, fuel, etc.lines. Have cracked loose the most stubborn fittings using this brand and never rounded a fitting. The high price is a factor but is outweighed by time saved..not to mention knuckles. Good vid on your "spiral friends". Best to you and yours.
good video thanks, going to buy set tomorrow from advance
Thanks I need this all the Time .
Hey Nice addition to the tool box.
i had the harbor freight version of these and it worked good! everyone should have a set!
I didnt know they had them!
Me neither. I’m going to search now.
I've looked and have never seen them at HF.
@@robertpaxton4849 I think I showed them in the Top 10 HF tools video I did I found them in the store and snapped a pic. Seem useful but at work I have no time to waste and these seem like they work much better than the HF ones would because of their design.
I just bought it and it literally saved me $$$
We call them turbo sockets, I cannot stress enough to coworkers and newbies how important this type of socket is!!! Great video my brother!
Thank you! They are SO nice to have and have saved me a few critical times
Always start with a 6 point socket that usually gets the job done instead of going to all this b******* and I'll even reuse the damn bolt.
@@unleashedrider4309 I NEVER use 12 points unless its actually a 12pt fastener. I rarely have things round off but sometimes they have been damaged before or are very rusty and shit happens, thats what these twist sockets are so awesome for!
Very helpful,thank you for sharing.Dealership I bought used car from used threadlocker on oil plug.I asked them why,they said it might come off.I have never had a oil plug come loose on any vehicle I ever had in my life.
Alright so I went got the deep sockets of the nut extractor tool twist socket set here and it worked instantly and there very good to have very awesome to have and get they help alot good luck and good day
Great video, I've been doing some maintenance stuff on my mower and tractor and have a bolt rounded off. Very little space to get into but I think it will do the trick.
Excellent demonstration! and good stories. Sub'd & Liked.
Awesomeness!! Great Video Review!!
Thank you Justin! I love these things they are the BOMB!
The old Sears/Craftsman had these, for around $50 for the set. I got a set a few years ago and they are made in USA and are awesome tools when your in a pinch. I have only had one time that they didn't work because the bolt was just too soft.
I've used a harbor freight set of these to remove a drain plug that had been way over tightened. Worked great, bought a new plug, good to go!
What exactly is the product called that you bought.
I’ve got to do that same thing today. It eased my mind to read your post. The last person who changed the oil on this car rounded the bolt and left it. I’m just going to do it for this customer, because I know a shop would charge her an arm and a leg to remove it.
Great Video, nice stories👍👍
Thanks for the demo.
Sure! These things rock
I have had the irwin version of those for almost 20 years. Never had an issue with them, not that I used them as often as you have it seems. Good presentation though, you are good at explaining and telling stories.
Thank you I appreciate it!
I got a husky set at Home Depot to remove a tough rounded rear brake caliper bolt. It worked better than expected.
Did you replace the bolt?
Yes, I took off the old bolts, replaced the calipers with rebuilt calipers, and put on new bolts.
Nice informative video. Keep it up.
Hey thank you!!!@ this helped me amazingly!!!!!!
Merci, had a little problem with nuts on my RAV4 today while attempting to change tires for the first time. Seems two or three nuts were stripped...This explains what needs to be done. I'll be able to talk with garage folk.
Thanks for the info
Excellent!
I like the ones that you can put a wrench on had them for 10 yrs np
Gear wrench has the new bolt biter sockets out . It’s a nice set Napa has them in their third quarter flier
GREAT IDEA, It would be nice to see this same design manufactured in a box wrench style.
They sell similar and spline drive, these work great when hammered on.
Mac makes a wrench set with the twist extractor on the box end
SKIL Secure Grip Self-Tightening Box Wrench..............and a sledge hammer.
Having the worst time trying to get off some torque converter nuts off a 4r70w trans. Gonna buy a set of these tomorrow
I got some tonight for about $40 from autozone 5 pack oem tools is what's printed on them I'm going to try them out very shortly and they have shallow and deep socket I bought the deep socket set of them thanks have a good day will respond when use them
Shake it up baby, twist and shout
1
Nice demonstration! Still need a set of these sometime.
They are awesome! I imagine where you are with all the rust these would be invaluable!
Yep. The problem for us is how often bolts like to break no matter how long we work on them. I can usually get them, but sometimes there is no avoiding it.
Not jealous my man! If I lived out there I'd have to have a different profession!
I bought a cheap Chinese set but it still works great.
i have a of small set that i got that are craftsman and they do work well in certain circumstances.
Aircraft mechanics been using these for years to remove hiloc collars
I got to deal with a few of those bolts tomorrow. So I went to get the irwin ones. Hope they work 🙏
They did the job!!
Ill give them a shot, working on 91 ranger and thing pure rust
I have to remove the dipstick holder bolt which was external torx but now it just about looks like hex because I took some advice I found in the wrong way and killed it. It's about a 6mm because a 6mm socket start to try to bite, so of I can find a set in smaller sizes that should work for my application.
Rounded off 4 bolts in a row today, I got them all off, but damn, gm cg joint bolts are like plastic, I was using the right socket too ugh, frustrating, but I use the OEM rounded off bolt set, worked amazing with my impact and some heat
Also work well to get off rounded off lug nuts.
I have a propane tank that is leaking around the capacity gauge. The 4 screws holding it in are seized or rusted. They are made to use only a flat screwdriver to turn them. I have used PB blaster on them and Kroil oil. Still not budging as it may not be finding its way up under the screw well enough.
Found where I might can heat them one at a time with a soldering iron---can't use any other type of heat with it leaking right there. Haven't tried that yet.
So in desperation I will try this technique....see if they get even the tiniest bite and can slowly start turning them out of there. Never heard of these and just happen to run across your video. What a great thing. Jesus bless.
Any other suggestions from you or anyone else is welcome. Thanks.
So I used a set like this to get some stripped lugs off of my Wrangler...worked great, only problem is with the last two lugs. I used the provided punch tool to remove the nut from the socket, and it got lodged in the nut. I was able to get it off the socket, and removed the last stripped lug. Tried the other end of the punch tool to remove the nut from the socket, and THAT end got lodged. So now I have what looks like a stripped lug, with a punched lodged into it, followed by the 3/4" socket, and the other lug nut on that end. It's one big mess and I have no idea how to dislodge the nuts from the punch tool lol.
First!! Haha I've always wanted to do that! Thanks for the video!
Of course! Thank you for watching and always leaving a comment!
ROCKET SOCKET brand twist socket set worked the best for youtube channel "Project Farm" to remove rounded off nuts & bolts with no damage to the tool itself being used, and the set only costs $69.95. Made in USA.
Can this used in Mcgard nut ? Its really tight and i lost my secret key lock
Will something like this work on reverse torx bolts too?
Thanks man, went to HF and bought a set
What it the product called I called HF and they didn’t know what I was talking about when o asked for a twisted set
@@devin7376 extractor socket set. Item number 67894 or 96335 for the metric set. 67897 or 96334 for the SAE set.
My stuck bolt even rounded-off the 14mm twist-socket??!! VERY perplexing!!🙃
ow do i removed this 10mm seized bol without breaking the L shaped bracket weakly tack welded to the fuel tank area......@
Will this work with a torx bit?
Omg thanks you
What about bolts that the head broke off...but still have the threaded shaft sticking out?
Works the "Nut" end also?
Do they work with torx screws?
Just bought a set.
The Blue Point is probably rebranded Irwin. Rocket Sockets are what I would recommend, based price and quality, even over the Snap On.. Made in US and works better than the Irwin’s.
I need help getting a way to get the bolt off of a spark arrestor on a Poulan chainsaw
Do they works for frozen cliapper bolts
Thanks, gonna try this on my catalytic converter
Only worked on two of the three bolts, the third one was just too rounded
I have a damaged nut holding on my front brake caliper it was rounded too much for the right sized socket to fit and too much material for the next smallest one. Dremeled the nut down to size, hammered socket on and it just fell off, stripped of and couldn't bite deep enough to hold on.
On the "Maximum Impact" Twist Socket Set, will any of those sockets work well on a 15mm nut??? I see that "9/16_14mm, 5/8_16mm", so it would seem like a 15mm is not addressed in this set.... Thanks much.
Cant speak for that set, just shared it as an affordable example. It obviously is not exactly the same as the set I showed in the video.
craftsman makes a set, usa made. same ones as mac tool. Thankfully i havent had to use them yet. Another handy tool is a cone shaped stud/broken bolt extractor, i got one from autozone for like $12
Craftsmen.... us made 🤔
Finn Green hard to believe but it still can be found brand new. Mostly small stuff
Ethan ridesbikes
I thought that China ruled
Was in Walmart
Picked up a half in craftsmen ratchet with tag in place
The directional tab was already stripped within the tachet🤙
Trying to replace my intake camshaft position actuator but the bolts stripped helllppppp
I can’t find one for my bobcat 1 1/2” size very large bolt head let me know if you know of a company that sells one.
If you want to round off bolt use a HF open end👍🔧
Hah! Should have done that 😂
In that bolt extractor set is there the size 30mm.
Thanks for the video. I really needed those when I rounded off 1 bolt on each Miata seat, ended up grinding the heads off to get them out.
Can you do a video on burping the cooling system on the Cherokee if you all still have it? I've tried multiple times and not having any luck. I've got the EPAuto spillproof funnel kit from Amazon and can't get it to seal on the radiator neck either. I'm thinking I'll have to park it uphill on car ramps and find a funnel that will seal to get it done lol. Mine's a 99 Cherokee. Thanks
Hey! If you cant get it bled you likely still have a leak somewhere, the 4.0's dont usually take much to burp so I'd suspect an issue. We just did a video on using a Coolant Pressure tester, I would use one of those to test your system first and make sure no more leaks, and if it passes and you still cant burp it you should try a vacuum filler. You do need air and a compressor but they work fantastic for filling cooling systems without having to bleed later, I will be doing a video on mine and showing how to use it soon
@@GearHeadsGarageChannel Thanks. I was thinking that there is a bubble in the line. It will stay at 210 degrees for 5-10 minutes then jump up to 260 for a minute then back down to 210 and over and over. I've flushed it out, replaced the radiator and thermostat a few days ago and still doing it. Going to replace the thermostat again or just remove it for now. I was thinking the air pocket hit the water pump and overheated until the coolant reached the pump again. Vacuum filler is on my list to get along with the leak tester.
@@central_ky_prepper2679 Check out the kit I have in the video we posted on the Miata from a couple days ago it is a leak tester AND a vacuum filler in one and has every adapter you would ever need! Its a very reasonable price too for both things. I would consider the thermostat sticking a possibility(one time we got 4 bad brand new ones IN A ROW from Napa) but I would still rent a pressure tester if you can, I doubt you have that much air in the system something else must be going on.
@@GearHeadsGarageChannel That's a pretty good price on the master kit. I had the Astro on my wish list on Amazon. I'll add that one to it as long as it has the vacuum filler kit with it. Thanks for all the responses to my questions.
@@central_ky_prepper2679 From what it looks like this kit is the exact same kit as the Astro one, probably made in the same factory
what was the name of these bolt distractor?
did you know blue point has a twist flip socket set in 1/2 drive that is good for lug nuts and locking lug nuts
Sounds like you have some of the same kind of luck I do! And my name is Jesse also 🤣
Luckily I dont need to pull them out very often. Probably only once every month or two, but everytime I need one and it works I feel like it was worth the purchase all over again. It has saved so many hours.
Correct me if I’m wrong but you use the size same size extractor as the stripped bolt?
The extractors are labeled for the size of stripped heads they should be able to grab onto yes. Sometimes I'll go a size down if one is really bad or damaged.
What is the part number for these sockets
Got my set for $19 at Amazon.. use it weekly
Have you ever used these on a stud? Got some broken exhaust manifold bolts on my GMC truck plus several rounded bolt heads. (Did see you talked about bolt heads broken off)
Yeah I have used them on studs as well you would need a smaller set though. Usually if the stud is sticking out though I will soak it with WD-40 and heat it up and use vice grips. Take the manifold off and you should have enough room to work with.
@@GearHeadsGarageChannel thank you. The manifold is already off and now I have around 1/4 inch nubs of the broken bolts to remove. I'm really hoping that the remaining bolts do not break off flush with the head.
If the original size of an oil drain plug was 10 mm, and got rounded off, what size extractor head would you use? Is there a size 9 or 8 mm?
if you have a full set like this then you use whatever fits.
Do they have something like this that works with the slave and master cylinders on Miata? The line is in the way of a tight , tight connection.
A line wrench is a better option for that or a line wrench style crows foot. People often round them off because they are trying to use an open end wrench.
Thank you. They are soooo tight on there!
5:36..... Just close the vise to slightly above the size of the head of the bolt then if you hit it a few times it doesn't mark the anodised black coating
What about Sparkplugs?
Hello body.will these work on my alloys.?
Its the anti-theft screws.
This type of tool should work but you would want a different size than what is in this set. I would try and find the right key before going this route.
My set (not this brand) explicitely says to NOT use a hammer but only turn the nut and it will start gripping.
Do you think it would work with the nut? Got 2 spinning nuts on a strut mount. Tried a nut splitter only put a crack in it
Are the nuts and studs spinning together? If thats the case best bet is cutting them off. This tool helps with a rounded off bolt or nut but that doesnt sound like what you are describing.
@@GearHeadsGarageChannel yeah lol opted for that route. Lol thank you for informing video though
Can u do a video on rear rusted 02 sensor stripped and ued the same tool from 7/8 or 22mm to 11/16
Bro I have the same issue with the 11/16 n I have not manage to take them off my wheel.... idk what else to do....
@@ivanserrano3722 I had to cut it out and retap it
@@isrealperez9069 wow thank you brother! That was faster then what I expected on a reply!!!... thanks alot much love...
@@ivanserrano3722 get it real tight until they break off the wheel then buy some studs pop off the old stud and pop it back on for a min I thought we were talking about rear 02 sensor I've bought the tool but didn't work for me
Do they have a non marring version of these? For delicate work of course
That would be a socket. The nature of these are to dig in and remove an already damaged fastener that you will replace. If it is damaged and you cant use a socket of some sort to remove it then dont reuse the fastener, replace it and who cares if it gets damaged using these.
Would you use this set to remove a damaged lug nut on a wheel?
Yes, and Irwin and GearWrench makes a set specifically for that. Irwin’s are shallow and GearWrench are deep and both can be used with impacts. You can even buy just the size you need on Amazon. .
Great video and clear instructions, thank you. So, how much did you pay for this set?
It was awhile ago but I think I paid around $190
@@GearHeadsGarageChannel Cool, thanks. The $20- Bolt-Grip 5 Piece Expansion set by Irwin did the trick for me, using your techniques in the video.