29:00 I am pretty sure that I saw the high latency vid.tx if I compare the ground/vlog camera where I can see the actual drone moves compared to the video I see on the Herelink radio. At least 2 seconds latency, I guess.
I am a beginner and had a friend setting up my Herelink and it’s not working like yours , when it gets armed my motors are in full throttle any advice ?
One option for compass calibration in MP is for local calibration. with this, you don't need to rely on telemetry and the laptop to do the processing, and it's onboard instead. you need to have the vehicle level, on each side, back front, and upside down to achieve an accurate calibration. your movements are not sufficient to give a good calibration. you should select which compass/compasses to calibrate. having 3 active ones is likely to give you descrepancies. better to place one well located compass, and cal it well than 3 where you have no idea where they are.
you are describing an accelerometer calibration here, not compass. Though your comment makes sense for compass calibration, and indeed an onboard cal is the best to do.
Couldn't we do the Auto tune in Loiter mode so that the drone stays in place? Thanks for the informative video! You got yourself a fan and a subscriber!
Hallo bobby, I have a problem, I con't get the video on my herelink I have gopro, I check with an other monitor, gopro osd is working, I get very little on internet, can you help me. thanks
I can see Hobbywing XRotor Pro X8 with 30 inch propeller with that set up? Tell us about Payload and aprox max flight time, and you test over how many meters over sea level? Thanks.
Hello friend! I have a problem connecting the same equipment to the PIXHAWK flight controller. More precisely, I connected it correctly, the video from the copter is displayed, the control channels are correctly displayed in ardupilot, but the telemetry in the form of batteries, satellites and everything else is not transmitted to the remote control, the remote does not see Pixhawk. at the same time, Pixhawk itself sees the remote control on SBS. it seems that I did not correctly set the telem or mavlink port settings. Please tell me what settings I could have missed, or maybe there are screenshots of the settings?
Hello friend thank you for sharing the experience do you have any Idea how I can use my own AHRS on the pixhawk my friends have designed their own AHRS and want to test it on pixhawk is there any way to help them?
19:00, how do you know by measuring voltage and mAh used if one of the two 12S packs is disconnected? Would you explain how you make this affirmation? You must have an amp meter on both battery connectors to do that.
I noticed , Joystick....does this mean flying is controlled over Mavlink ?... ( like the other functions ) . I know Joystick is only available in QGC when its actually attached (to an android device ).
Friend, good night! Could you let me know if I can use esc's BLHeli and BLHeli-s on multirotors with apm2.6 and Pixhawk? These esc's work with these controllers???
Hi, nice video. Have you tested the range of the herelink? I have seen the other vid but wanted to know a actual user review in the real world scenario.
Hello Mate! Great videos! Thank you and keep up the great job. Pardon me for speaking out of topic. I just recently purchased and installed the orange cube onto my Carrier Board (Kore). Which version of the firmware do I use with the orange cube? Are there any modifications needed to the file name or extension prior to loading the firmware file? Thanks, Mike
Hi Mike I just saw all 7 of these comments. :) I am unsure- we haven't used any of the orange cubes yet. I would recommend you hop on the forum and ask there. discuss.cubepilot.org/
How do you control the sensor payload? and configure buttons to for image capture, and gimbal mode, and is there a way to have an second HereLink dedicated for Sensor payload and gimbal control?
In this configuration the customer wanted to have a dual operator setup, so the gimbal is controlled by a separate Futaba radio and a separate operator. Regarding dual HereLinks that may be possible but I am unsure
What solution do you use for gimbal control with the Herelink? I am building a commercial drone for inspection and im considering the herelink system but I need to be able to control the gimbal and camera through the herelink. I have seen touch screen control, as well as various button layouts for switching the wheel between pan, tilt and zoom. Would be very interested to hear your thoughts on it. Love your gear man, if I didnt build my own systems specifically for an arctic climate I would buy one of yours in a second. (Heres to hoping DJI gets sabotaged by the Chinese government like Huawei and tencent lol)
Hey thanks for the kind words. You can set up the gimbal to be operated with HereLink. More info here: docs.cubepilot.org/user-guides/herelink/configure-buttons At the moment they are going through some bug fixes, so you may have to wait on those to be resolved before you can get everything working smoothly.
@@BobbyWatts Hey man, I just want to thank you for going out of your way to help me out. All the best to you buddy, you've got a great business model and a great product and I will keep you in mind when we do equipment consultations for some of the mining companies up this way. Oh also, just a suggestion, with the pixhawk config you could easily integrated the Here 2 RTK system into your base package for next to nothing. Its not ideal for mapping but as far as keeping assets and talent safe it adds that extra line of defense against interference for a very low price. Just a thought, cheers
@@flighttherapybullisticfpv133 Appreciate the kind words, glad I could help! Yes the Here+ RTK system is really nice! Very impressive performance for the price!
I used to rack my brains and wallet on ground up builds. Bought a DJI Inspire and never been happier.
Wonderful informative video on my favorite subject, big drones! Thanks, keep up the great work!
Thank you!
Thanks Bobby. Phantom Aerial Solutions did our first test flight this morning. Extremely responsive without a load. All went well.
Hi Terry, that's great! Thank you all for the support!
Awesome job.
29:00 I am pretty sure that I saw the high latency vid.tx if I compare the ground/vlog camera where I can see the actual drone moves compared to the video I see on the Herelink radio. At least 2 seconds latency, I guess.
iPhone 12 you can force personnel hotspot to 5ghz WiFi output.
Thank You!
if u select onboard calibration it really doesnt matter how it is initiated, qgc, remote or mp
I am a beginner and had a friend setting up my Herelink and it’s not working like yours , when it gets armed my motors are in full throttle any advice ?
One option for compass calibration in MP is for local calibration. with this, you don't need to rely on telemetry and the laptop to do the processing, and it's onboard instead.
you need to have the vehicle level, on each side, back front, and upside down to achieve an accurate calibration. your movements are not sufficient to give a good calibration.
you should select which compass/compasses to calibrate. having 3 active ones is likely to give you descrepancies. better to place one well located compass, and cal it well than 3 where you have no idea where they are.
Hey Thanks for the tip! Will have to give it a shot. Always learning....
you are describing an accelerometer calibration here, not compass. Though your comment makes sense for compass calibration, and indeed an onboard cal is the best to do.
Couldn't we do the Auto tune in Loiter mode so that the drone stays in place? Thanks for the informative video! You got yourself a fan and a subscriber!
You can do it with position hold mode. It stays in 5m radius doing its autotune thingy.
Mallikarjun SE thanks guys- I’ll give it a shot!
Hallo bobby, I have a problem, I con't get the video on my herelink I have gopro, I check with an other monitor, gopro
osd is working, I get very little on internet, can you help me. thanks
Wish I could see your PID before and after tuning
Nice video. Thank u
Tân Phạm glad you enjoyed!
can i add some more funtion in the receiver/ drone controller
How hard it is to make all the electronics work together , how someone like me can learn ?( great job by the way - George)
10/10 for that shirt :)
Thanks! :)
I can see Hobbywing XRotor Pro X8 with 30 inch propeller with that set up? Tell us about Payload and aprox max flight time, and you test over how many meters over sea level? Thanks.
Any idea where to get a spare power cable connector for the Air unit of the Herelink
for autotune GPS mode is recommended over althold
What about video range of this here link compared with connex?
Also can you help me with the gains which I can use for first flight so then I tune them later with autotune mode?
Hello friend! I have a problem connecting the same equipment to the PIXHAWK flight controller. More precisely, I connected it correctly, the video from the copter is displayed, the control channels are correctly displayed in ardupilot, but the telemetry in the form of batteries, satellites and everything else is not transmitted to the remote control, the remote does not see Pixhawk. at the same time, Pixhawk itself sees the remote control on SBS. it seems that I did not correctly set the telem or mavlink port settings. Please tell me what settings I could have missed, or maybe there are screenshots of the settings?
Nice video! ✈️
Mallikarjun SE thanks!
Mallikarju. If you ever come to Finland the ladies are going to love your name. Won't tell you why. Find out yourself. ;)
@@mil-fpv4931 😅😅
@@mil-fpv4931 is there a temple by my name?
@@mallikarjunse Not yet, haha!
Hello friend
thank you for sharing the experience
do you have any Idea how I can use my own AHRS on the pixhawk
my friends have designed their own AHRS and want to test it on pixhawk
is there any way to help them?
19:00, how do you know by measuring voltage and mAh used if one of the two 12S packs is disconnected? Would you explain how you make this affirmation? You must have an amp meter on both battery connectors to do that.
hello how many minutes did you get with this drone, what its total weight, make a video showing step by step configuration of herelink
How much will it cost me to buy a drone with the capabilities to delivery and with GPS recording capabilities and auto return home capabilities.
I noticed , Joystick....does this mean flying is controlled over Mavlink ?... ( like the other functions ) . I know Joystick is only available in QGC when its actually attached (to an android device ).
Hi ! thank you for this great video, can you connect 2 herelink (or another RC) the first for the pilot and the second for the camera op? best
Friend, good night! Could you let me know if I can use esc's BLHeli and BLHeli-s on multirotors with apm2.6 and Pixhawk? These esc's work with these controllers???
How much weight can it lift.nd what is the cost ..
If such a thing flies above/ near me, I will run as if there's no tomorrow
How to make a purchase?
Bro, Nice T,, could you share a link to the Image on it...
What controller do u like more? A3 pro with lightbridge 2 or cube with here link? What is more safetly? thanks¡¡
How much starting price?
How much for one of these
Hi, nice video. Have you tested the range of the herelink? I have seen the other vid but wanted to know a actual user review in the real world scenario.
Ya I have seen on RUclips, where someone checked video transmission range over 16 km and it worked pretty well
Hello Mate!
Great videos! Thank you and keep up the great job. Pardon me for
speaking out of topic. I just recently purchased and installed the
orange cube onto my Carrier Board (Kore). Which version of the firmware
do I use with the orange cube? Are there any modifications needed to
the file name or extension prior to loading the firmware file?
Thanks,
Mike
Hi Mike I just saw all 7 of these comments. :)
I am unsure- we haven't used any of the orange cubes yet. I would recommend you hop on the forum and ask there. discuss.cubepilot.org/
Excellent stuff Bobby! So you just using MP for the compass calibration and Qground for the rest of the settings then?
Hey Marc thanks! Yes that is correct
Why do you use 2 GCS while one could do all you need? Is there an advantage to that approach?
Has anyone tried a stylus with this thing ?
How much total cost
How to buy drone
How do you control the sensor payload? and configure buttons to for image capture, and gimbal mode, and is there a way to have an second HereLink dedicated for Sensor payload and gimbal control?
In this configuration the customer wanted to have a dual operator setup, so the gimbal is controlled by a separate Futaba radio and a separate operator. Regarding dual HereLinks that may be possible but I am unsure
@@BobbyWatts Can we simply use this as a video monitor for hd video at that range and mount it to our Frsky x10s?
@@DragginMix Yes I suppose that would be entirely possible!
SWIM wants to know how many hand grenades can it lift
I would love to share some emails with you in regards to setting up a miniquad with the capabilities of using my GoPro for my fpv camera.
Do you have to have Pixhawk for this device? Can it be used for others?
You don't have to, you would still have HDMI video and SBUS control, so I suppose you could use it with other flight controllers and devices
hi, can we power up pixhawk using apm’s power module as both is 6 pin
I am not sure of your question can you re-phrase it?
It working I'm also using the same but preferred to use recommend orignal power module
nice one !! the maximum range please ??
Info here: ruclips.net/video/J9Kte7sb3EA/видео.html
What solution do you use for gimbal control with the Herelink? I am building a commercial drone for inspection and im considering the herelink system but I need to be able to control the gimbal and camera through the herelink. I have seen touch screen control, as well as various button layouts for switching the wheel between pan, tilt and zoom. Would be very interested to hear your thoughts on it. Love your gear man, if I didnt build my own systems specifically for an arctic climate I would buy one of yours in a second. (Heres to hoping DJI gets sabotaged by the Chinese government like Huawei and tencent lol)
Hey thanks for the kind words. You can set up the gimbal to be operated with HereLink. More info here: docs.cubepilot.org/user-guides/herelink/configure-buttons
At the moment they are going through some bug fixes, so you may have to wait on those to be resolved before you can get everything working smoothly.
@@BobbyWatts Hey man, I just want to thank you for going out of your way to help me out. All the best to you buddy, you've got a great business model and a great product and I will keep you in mind when we do equipment consultations for some of the mining companies up this way. Oh also, just a suggestion, with the pixhawk config you could easily integrated the Here 2 RTK system into your base package for next to nothing. Its not ideal for mapping but as far as keeping assets and talent safe it adds that extra line of defense against interference for a very low price. Just a thought, cheers
@@flighttherapybullisticfpv133 Appreciate the kind words, glad I could help! Yes the Here+ RTK system is really nice! Very impressive performance for the price!
what is the maximum payload capacity of this??
wattsinnovations.com/pages/mfd5000
@@BobbyWatts dead link
@@charlesmarseille123 wattsinnovations.com/pages/mfd5000