Mine will select reverse and car moves but if I select drive it doesn't move and stays in neutral then throws a code p1734 gear actuation position in the gear selection shaft signal fault . How can I fix this ? Can I remove actuators with the box on the car ? Thanks in advance a fellow mechanic
Just a question after you fitted the clutch what was the procedure with getting it working. i.e programming the biting point, programing the gear change, pressurising the actuator?
Sorry to bring this one back from the dead.. just wondering if you had any recommendations for a budget diagnostic equipment to reprogramme a 508 semi automatic.. doing it on the drive and to say its a nightmare, is an understatement! 😢
why do semi-auto peugeot 3008 and citroen c4picasso slams loudly on the clutch plates when engaging gear to "D" after less than 10mins idling in neutral?? any good to this or was it bad??
Helow mate i have a bad juddering on first gear i have the same semi auto 208 2016 model what will be the problem and how much it will cost and how long i will take to fix and if i wana take an apointment to fix it thax matr
You dont have to lower the subframe ?? i watch other video and they lower the subframe and i do the same and now stuck with bolt spin around. Will be easier for me tighten bolt and dont touch subframe
What this little square doing on pressure plate? I order Valeo kit and pressure plate looks different the car dont drive and wont let me to learn gearbox is it mean i fit a wrong parts?
My dad's Citroen C4 has the same ETG6-gearbox. After clutch and flywheel replacement gearshift became even slower than before the repair. I counted it takes now 2-3 seconds (!) to upshift. In reverse gear the clutch slips so badly that it begins to smell. The car haven't done that either before the repair. Is there something wrong with the software? The work was done by a professional PSA specialized workshop.
Hi, we’ve got a 2010 Peugeot 3008 semi automatic which has a gearbox fault light that comes on and off, I need it sorting, would you be interested in booking it in? Cheers
My peugeot 3008 seni auto driving in auto changes to m3 then back to a3 any idea happend in 4th as well its like a curly m not like when its in full manual mode? Does this mean its slipping ?
Hiya mate, Don't suppose you know if it's the same layout on a 508? 2011 1.6hdi semi-auto. HaynesPro saying its an ~8hr job & i'm trying to figure out why..
I watch ur videos on tik tok lol i have peugeot 3008 semi it jerks bad in low gears slow when changing and judders and swops from a to m to auto in 3d some times is this clutch as had it done an flywheel seems getting worse and worse no one will do was gona drive 3 hours to u lol
![FNAF Into the Pit has A LOT of Unused Graphics | LOST BITS [TetraBitGaming]](http://i.ytimg.com/vi/6YhZCRdipl4/mqdefault.jpg)
Mine will select reverse and car moves but if I select drive it doesn't move and stays in neutral then throws a code p1734 gear actuation position in the gear selection shaft signal fault . How can I fix this ? Can I remove actuators with the box on the car ? Thanks in advance a fellow mechanic
Hi which garage is this, how much does a clutch replacement cost on a Peugeot 208 mk1 semi auto?
Just a question after you fitted the clutch what was the procedure with getting it working. i.e programming the biting point, programing the gear change, pressurising the actuator?
Mine drives like shit after new clutch and flywheel lol and some times swops to manual then bk to auto going dwn gears iv noticed any idea lol
Sorry to bring this one back from the dead.. just wondering if you had any recommendations for a budget diagnostic equipment to reprogramme a 508 semi automatic.. doing it on the drive and to say its a nightmare, is an understatement! 😢
I'm not sure tbh in lower end cheaper diag tools as I've never used them and hate to say something you buy it and not work
i have semi auto and from cold when starting f it sort of kangeroos moving from first after couple minets its fine wot could that be
Done a fair few of these got one to do tomorrow in a c4 grand picasso keep hearing customers saying not many garages will do them tho
Not many will get involved don't know why its a normal clutch job with pressing a few buttons
@bazmeredith exactly done harder Manual ones tbf top work tho mate
My 3008 judders on pull of sum times swops from auto to manuel in 3d and changes slow is it slipping ? And jerks in 1s and 2nd bad like ur rocking lol
why do semi-auto peugeot 3008 and citroen c4picasso slams loudly on the clutch plates when engaging gear to "D" after less than 10mins idling in neutral?? any good to this or was it bad??
Hi nice vid, I’m doing mine this weekend and was just wondering do you have to de-pressurise the hydrological first? Cheers
Helow mate i have a bad juddering on first gear i have the same semi auto 208 2016 model what will be the problem and how much it will cost and how long i will take to fix and if i wana take an apointment to fix it thax matr
How many miles did you do when replacing the clutch and test driving it making sure it all works
You dont have to lower the subframe ?? i watch other video and they lower the subframe and i do the same and now stuck with bolt spin around. Will be easier for me tighten bolt and dont touch subframe
What this little square doing on pressure plate? I order Valeo kit and pressure plate looks different the car dont drive and wont let me to learn gearbox is it mean i fit a wrong parts?
My dad's Citroen C4 has the same ETG6-gearbox. After clutch and flywheel replacement gearshift became even slower than before the repair. I counted it takes now 2-3 seconds (!) to upshift. In reverse gear the clutch slips so badly that it begins to smell. The car haven't done that either before the repair. Is there something wrong with the software? The work was done by a professional PSA specialized workshop.
Did you relearn the gearbox?
Hi, we’ve got a 2010 Peugeot 3008 semi automatic which has a gearbox fault light that comes on and off, I need it sorting, would you be interested in booking it in? Cheers
The clutch hydraulic fuild does that tank stay full after bleed as mine is lower its not full
My peugeot 3008 seni auto driving in auto changes to m3 then back to a3 any idea happend in 4th as well its like a curly m not like when its in full manual mode? Does this mean its slipping ?
Hi my 3008 semi auto says a3 then m3 some time when driving any idea judders a little aswell on pull off?
Hiya mate,
Don't suppose you know if it's the same layout on a 508?
2011 1.6hdi semi-auto.
HaynesPro saying its an ~8hr job & i'm trying to figure out why..
Hi baz i need some info if possible
Can i ask someone questions please
I watch ur videos on tik tok lol i have peugeot 3008 semi it jerks bad in low gears slow when changing and judders and swops from a to m to auto in 3d some times is this clutch as had it done an flywheel seems getting worse and worse no one will do was gona drive 3 hours to u lol
Don't think you really have to do the learning and driving bit.
If you want your gearbox to work properly and not ruin your new clutch, you do have to do relearn procedure.