You've been very helpful. I will go to my machine and follow your instructions on retrieving the code and finding out the correct repair. Thank you so much!
this washer is no good…. anytime i press “rinse” it drains the water, goes to 10 to 9 min, then starts to add more water to the load again and then time goes back up to 15 min and starts over.
Your right, some techs do watch your videos This may help me in future. I am primarily a whirlpool tech but like Samsung and LG (except the LG fridge and you know why!) appliances and come across them occasionally. I like to see what is common failures in each one or what others have come across. Whirlpools are easy for me I see them 8 or more times a day. But what fails on a Samsung may be different (and I think less common) most of my purchased appliances are Samsung
If you have one of these. Always pull the back cover and check the wires going to the water pump. They break from vibration. Very common issue. It will disable the washer. Very simple fix.
I have this exact same machine and did everything you said to do in the video and every watch cycle I put it through it spins like about 3 minutes due to spin cycle then it starts bouncing around and then it starts counting a higher number and it starts feeling with water how can I correct this
My problem is the dc code. I’ve moved the clothes around but not added more clothes. Is there another solution? It doesn’t happen all the time but when it does it’s pretty Ann when you think your laundry is ready for the dryer and it’s not, 😭😭😭. A friend told me today she stopped her washer from going into dc mode by loading everything circular. Any suggestions from you would be great. Thank you. By the way I have the exact washer as your are demonstrating on. Thank you
Ben my washer just like this one in this video was dropped durning move, and not it won't spin out. The tub inside moves agressively for a few times like it wants to start to spin but then stops and goes back into rinse cycle by filling up with water again. And repeats this action but does never catch on the spin cycle. I sure you can tell me whats wrong and if it can be fixed easily.
In spin mode, it spins for a while and becomes unbalanced. Once I pause and reareange laundry, it goes back to the beginning of the spin cycle. Is there a calibration function?
Hey, I have a Samsung Active, dual wash, Toploader model number, WA11M 8700GW error code 4C came up so replaced the water inlet valve. Now it drips water from detergent dispenser ( dispenser has been cleaned ) when machine is off 750 ml per 12 hours can u help..
I just watched this video because I have the same make and model. Do guys just change the part that is defective or take it apart and repair it? Every video that I have seen says replace but that can be costly
Hey Ben. Great video. I have this exact washer. Don't have any codes showing but the washer will spin and appear to be out of balance then start the cycle over. I've changed the suspension rods and it's still doing the same thing. Without a code I'm not sure what to check next. If it does finish a load the clothes seem wetter than they should be. Thanks for your information.
I can't do the quick test mode every time I push them three buttons the washing machine turns out and to test the spin test mode on my washing machine I have to hold the delay start and Eco Plus button and you said I was supposed to hold the pre-soak and delay at the same time so I want to know if I have to push something else on my washing machine I have the washing machine that has smart Care on it
I have an error code E2. Drain pump not working. I got lucky last time as the black wire had torn from the drain pump and I was able to reconnect it. This time, the same thing happened but when I reconnected it, the drain pump stays on continually. Any help woudl be apperciated. Thank you!
Your software says 2A my washer shows 28. Does that mean it needs to be updated? Also my spin test my numbers are slower than yours when it is spinning.
I have a Samsung top load washer model wa45h7200ap/a2 . It is roughly 8 years old. I am having a problem the initial start it does not weigh the clothes in the tub. It will fill the water to the top whether you have 10 pair of socks or 10 pair of jeans. Other then that the machine works great. I replaced the water level switch it not make a difference. I was wondering if you can help thanks.
Great Video! thanks for all the help. My problem: washer is unbalanced and I need to replace some of the suspension rods. However, Samsung had a recall on this model a few years back. we could get a small refund, a replacement or a repair due to the lid/ top popping off during the spin cycle and causing injuries. We did the repair. DOES ANYONE KNOW HOW TO take out THE 2 SCREW TYPE PIECES OF METAL THAT ARE HOLDING THE lid TOP TO THE BOTTOM OF THE WASHER? i dont even know what the piece of metal is called. Its not really a screw... kind of like a twisted letter J. thanks for any help!
Hi Ben. I have thecsame washing machine as the one in this video. Mine is a 2014 with an error code UE or 4E. The load gets unbalanced through regular wash cycle and will not complete the spin cycle. Clothes are then left too wet for dryer. Towels and bedding seem to be most problematic. Just now I rebranded the items and set the machine to spin. I left the laundry room for a few moments and returned to a huge flood. Any idea how to fix my dilemma,?? Michelle Nichol
I have error code nF. My washer is filling up with water wayyyy past the top of the washer drum and spilling out onto the floor from inside the washer. What should we do? or should we go get a new washer? thank you in advance.
i have the same problem with my samsung overfilling. The cold water valve stays open intermittently. I blew out the pressure sensor line and their was not blockage. i ordered a new pressure sensor and valve head assemble. Why would it work sometimes and not others? Can't afford to have a repair person fix it right now. What do you think is the problem?
Hi Ben, We can't afford to get a repair guy right now and this washer is driving us nuts. Someone posted the same issue of over filling and coming out of the bottom. We don't have any codes due to a power outage that happened the same day the water started spilling out. Is this something we can fix ourselves? If so, what do we need to do?
When it turns on do valves immediately start and never stop even if cycle hasn't started, or cycle starts then over fills? It's either going to likely be pressure hose being damaged or unhooked, or bad water valve
AEESOME video, many thanks!! We have a very very similar model, ours has the glass top door, but other than that, same. Our issue that we have is when we hit Start, it only beeps, like the door is open. I was able to do your tests and the door locked/unlocked without any issues. The only error code was 9E (x01) and someone in the comments stated voltage. The weird thing is that if we persist long enough, change the settings a few times over and over, it will eventually start. Again, we hit start on any setting and it just beeps, similar to the door being open. Any thoughts on what else to check, please let me know.
Hello I changed my pressure switch as well as the inlet water valve it has been working great for about a week and this code popped up LE AND IT SOAKED MY FLOOR :( any help appreciated
I’m getting the nF code everytime I try to wash on a normal setting I checked drain tube and it’s not clogged I’m stuck what is the fix or how can I clear this code please help
I have this exact same washer. I have a DC error code. I've changed the rods and checked the nut in the bottom of the tank. Also cleaned the shaft and bottom of the tank. It said it could to the hull sensor. Can you tell me how I could check this?
Any luck on this? I have the same washer, was getting dc and it would refill and spin again. I just changed the rods and checked the nut. The few loads I have done since changing the rods now doesn’t stop and throw the code. But it never got violently loud before and now it does and just raises the time and refills and spins again.
BEN !!! What I don't understand is why testing will show everything is fine then when I go to put it on a cycle it runs and will run up to a certain point and then just sit on a number and not do anything!!
Because the error and diagnostic system in Samsung washers is just awful. Most other brands have more robust tracking and logging of codes, and Samsung gives you a few vauge ones that are lucky to work.
Try to spin the plate freely by hand when its not running. Is there any resistance from the plate? If it spins too freely, the plate may have stripped against the spline/gear of the washer, so when there's tons of water/clothes, it just spins on the gear splines and never actually moves.
Great video. I have Samsung wa48h7400aw/a2. It stopped draining so I ordered the drain pump. In the 2 days it took to get the pump, it stopped filling. I changed the pump and it still doesn't work so I changed the inlet valve and still, it won't fill. I was getting a 4c error and when I entered the test mode using this video, I got error JC-0E. Any idea? Any help is greatly appreciated. Thanks in advance!
hi ben . thanks for the video..i have a wa422prhdwr/aa02. once i turn it on it start drainig and throw me the IE CODE.. manual said water level sensor is bad ....i unhook it and blow in it ; i can hear the diaphram working . what do u think. thanks again
Blow in the plastic tube while holding closed the other end of the hose to check for any possible cracks/air leaks in the hose. If there are any, replace the hose.
You'd need to get them from Samsung. Find your model# and see if you can find a SERVICE manual online or a Technicians manual (not the homeowners manual). They may vary slightly from model to model.
I have this washing machine. As soon as I turn it on the drain pumps comes on moment later the error code 1E shows and the drain pump continues to run. I poured water into it and it is definitely pumping the water. All you other test worked but must do it fast or the Pumps starts again and the 1E code comes on
If the pump is ALWAYS on, then the pump relay on the board is stuck. Unplug the unit, and take a screwdriver. Use the handle to gently tap all the relays. Go over them a dozen times each. See if it stops. This should solve it, but likely temporarily... Its gonna need a board replacement as some point.
Nice video ! Hey so my motor works drain pump works in test mode. Machine won’t drain on normal mode I took entire machine apart literally . Wiring looks good will a board reset make it work? And if so how do I reset it? Love your videos very very detailed! So I worked on it today and no codes pump works now one issue I have is when it rinses it becomes out of balance and it stops it with no code . If there was 9 mins left it restarts that section to 17 mins again over and over and over. Wonder if it’s due to not having the update of 2A mine says 28
@@xpan5694 opened up rods and inserted hard rubber to make them stiff in center of white plastic. And that sucks nf code water supply valve clogged maybe?
So I get the nF code. Any idea how to fix this? Because when I wash my clothes on 'Nornal' it certainly fills up with a lot of water and does everything untill it needs to spin...once it gets to that point it just stops, gives me the nF error code and my clothes are all humid still😫please help meh. Side note. It gives me the same error when I put it on 'Spin', not sure if it needs water to only spin....but yeah
Check and make sure unit is level. Then check underneath the wash plate to see if the washer bracket underneath is in good shape. If it is, likely bad suspension rods.
Yet that shouldn't change much in that the only difference is that you'd use the jog dial to find them. The error code manifest is included in the video.
also, the error code is 9E. i tried doing the tests you advise but not responsive. I can get it to work by doing like i have been (power on/off around 15 times)
@@bensappliancesandjunk is it worth just replacing the Control board and installing it myself or just buy another washing machine? I've unplugged it before for about 10 minutes but no luck, but i'll try 30min now. Thanks for the quick reply
Please help me wit my too-load washer it show the “NF” code. Once it gets filled up with water and it’s time to start washing, it stops and the code comes on.
Nf is a water valve code. If its filling ok, is it overly hot water like thr temperature is reversed? It could be the hoses are reversed or the valve sensor is bad
I changed the suspension rods and the machine when in spin mode goes crazy and it won't finish spin cycle I check the nut in the middle of the drum and it's tight when the machine is off the drum is tight but when it goes into spin it just goes crazy what could it be causing this any help will be greatly appreciated Thank you
I know you posted this 10 months ago. What I did was install the new upgraded Samsung suspension rods for the drum and it fixed the problem. Ran good for 3 years so far.
I didn't have any issues pop up while going thru this video with u, but before, I was getting an NF error code. The barrel is slow to start spinning, but it did go to the same RPM urs did. U did amazing going thru it slowly and thoroughly. Even a newbie like me was able to follow along easily.
Same problem with mine. It even started adding water when I set it to just spin. Resets over and over and eventually gets dc code and stops. Did you ever get yours figured out?
With the error codes I get an upside F and E on the bedding. When in the test cycle the same code pops up flashing and beeps every few minutes. I also get nd when I run a normal cycle.
You've been very helpful. I will go to my machine and follow your instructions on retrieving the code and finding out the correct repair. Thank you so much!
This has been the best information on a Samsung washing machine. Thank you so much.
This is the best diag video on YT. Thanks so much!!!
this washer is no good…. anytime i press “rinse” it drains the water, goes to 10 to 9 min, then starts to add more water to the load again and then time goes back up to 15 min and starts over.
Your right, some techs do watch your videos This may help me in future. I am primarily a whirlpool tech but like Samsung and LG (except the LG fridge and you know why!) appliances and come across them occasionally. I like to see what is common failures in each one or what others have come across. Whirlpools are easy for me I see them 8 or more times a day. But what fails on a Samsung may be different (and I think less common) most of my purchased appliances are Samsung
If you have one of these. Always pull the back cover and check the wires going to the water pump. They break from vibration. Very common issue. It will disable the washer. Very simple fix.
Thanks I have just replace the spring balanced it’s working great for now thanks to your diagnostic video keep up the good work thank you
Hello can you tell me how do I check the suspension rods please
I have this exact same machine and did everything you said to do in the video and every watch cycle I put it through it spins like about 3 minutes due to spin cycle then it starts bouncing around and then it starts counting a higher number and it starts feeling with water how can I correct this
My problem is the dc code. I’ve moved the clothes around but not added more clothes. Is there another solution? It doesn’t happen all the time but when it does it’s pretty Ann when you think your laundry is ready for the dryer and it’s not, 😭😭😭. A friend told me today she stopped her washer from going into dc mode by loading everything circular. Any suggestions from you would be great. Thank you. By the way I have the exact washer as your are demonstrating on. Thank you
Thank you for this!
Do you have a picture of the door latch/strike? It would be really helpful if you did!
Ben my washer just like this one in this video was dropped durning move, and not it won't spin out. The tub inside moves agressively for a few times like it wants to start to spin but then stops and goes back into rinse cycle by filling up with water again. And repeats this action but does never catch on the spin cycle. I sure you can tell me whats wrong and if it can be fixed easily.
Having this same exact issue it fails to do the last wring out it goes back to 34 mins from 9 mins every trip
probably the belt
Needs new shocks/suspension rods.
Prezado amigo tens o manual de serviço dessa máquina.
You're the man 👍👍. Appreciate this video very much
That's awesome, thank you so much.
I get 9e on my washer and my problem is that the washer won’t start it just beeps but then if I let it sit for a while and press it works
In spin mode, it spins for a while and becomes unbalanced. Once I pause and reareange laundry, it goes back to the beginning of the spin cycle. Is there a calibration function?
Hey, I have a Samsung Active, dual wash, Toploader model number, WA11M 8700GW error code 4C came up so replaced the water inlet valve. Now it drips water from detergent dispenser ( dispenser has been cleaned ) when machine is off 750 ml per 12 hours can u help..
Awesome video , very helpful 👍
I just watched this video because I have the same make and model. Do guys just change the part that is defective or take it apart and repair it? Every video that I have seen says replace but that can be costly
Hi, great video I'm getting a 9E code i can't find any info on 9E I tried doing your test but i can't get any spin or water test or door latch?
Sir I have the same washer in the video and my washer will not go past washing mode. Can you please help.
Hey Ben. Great video.
I have this exact washer. Don't have any codes showing but the washer will spin and appear to be out of balance then start the cycle over. I've changed the suspension rods and it's still doing the same thing. Without a code I'm not sure what to check next. If it does finish a load the clothes seem wetter than they should be.
Thanks for your information.
I have this same problem have you found out what it was causing this yet?
Ben has another video and addresses this at the end - potential tub issue
Thank you . Just have my washer and back running. It is Ub error code.
I can't do the quick test mode every time I push them three buttons the washing machine turns out and to test the spin test mode on my washing machine I have to hold the delay start and Eco Plus button and you said I was supposed to hold the pre-soak and delay at the same time so I want to know if I have to push something else on my washing machine I have the washing machine that has smart Care on it
I have an error code E2. Drain pump not working. I got lucky last time as the black wire had torn from the drain pump and I was able to reconnect it. This time, the same thing happened but when I reconnected it, the drain pump stays on continually. Any help woudl be apperciated. Thank you!
Your software says 2A my washer shows 28. Does that mean it needs to be updated? Also my spin test my numbers are slower than yours when it is spinning.
Is it normal for it to fill up about 4 or 5 inches from the top with water on quick wash?
I have a Samsung top load washer model wa45h7200ap/a2 . It is roughly 8 years old. I am having a problem the initial start it does not weigh the clothes in the tub. It will fill the water to the top whether you have 10 pair of socks or 10 pair of jeans. Other then that the machine works great. I replaced the water level switch it not make a difference. I was wondering if you can help thanks.
When I looked under mine the belt had came off . Is it easy to put back on and why would it come off and still be in tact ?
Have this same washer and getting an 3E error code which says a hall sensor. But can’t find any video on how to replace it.
Thanks
I have an error code OE. The washer leaks from the bottom, and the water remains on, even if I turn off the washer.
Great Video! thanks for all the help.
My problem: washer is unbalanced and I need to replace some of the suspension rods. However, Samsung had a recall on this model a few years back.
we could get a small refund, a replacement or a repair due to the lid/ top popping off during the spin cycle and causing injuries. We did the repair. DOES ANYONE KNOW HOW TO take out THE 2 SCREW TYPE PIECES OF METAL THAT ARE HOLDING THE lid TOP TO THE BOTTOM OF THE WASHER? i dont even know what the piece of metal is called.
Its not really a screw... kind of like a twisted letter J. thanks for any help!
Hi Ben. I have thecsame washing machine as the one in this video. Mine is a 2014 with an error code UE or 4E.
The load gets unbalanced through regular wash cycle and will not complete the spin cycle. Clothes are then left too wet for dryer. Towels and bedding seem to be most problematic.
Just now I rebranded the items and set the machine to spin. I left the laundry room for a few moments and returned to a huge flood.
Any idea how to fix my dilemma,??
Michelle Nichol
What about a 4c error I think it’s water supply issues any suggestions?
Ben, I have a Samsung WA51A5505AC washer machine with a code error AC6, Is there anything I can do by myself to fix it?
Ben why would water keep running into washer even if you turn power off. The only way to stop water is too turn water supply valves off.?
Great video. I have a similar machine. But is WA456DRHDSU. Do you know the process for self testing this mode? Thanks
I have error code nF. My washer is filling up with water wayyyy past the top of the washer drum and spilling out onto the floor from inside the washer. What should we do? or should we go get a new washer? thank you in advance.
Replace water valves
Mine is doing the same thing smh
i have the same problem with my samsung overfilling. The cold water valve stays open intermittently. I blew out the pressure sensor line and their was not blockage. i ordered a new pressure sensor and valve head assemble. Why would it work sometimes and not others? Can't afford to have a repair person fix it right now. What do you think is the problem?
Hi Ben,
We can't afford to get a repair guy right now and this washer is driving us nuts. Someone posted the same issue of over filling and coming out of the bottom. We don't have any codes due to a power outage that happened the same day the water started spilling out. Is this something we can fix ourselves? If so, what do we need to do?
When it turns on do valves immediately start and never stop even if cycle hasn't started, or cycle starts then over fills? It's either going to likely be pressure hose being damaged or unhooked, or bad water valve
Would like info on how to calibrate the washer
I have a question, my samsung washer and dryer doesnt show the timer clearly, what should I do?
Does it operate but very dim?
Thanks for the video it sure helped.
Glad it helped
AEESOME video, many thanks!! We have a very very similar model, ours has the glass top door, but other than that, same. Our issue that we have is when we hit Start, it only beeps, like the door is open. I was able to do your tests and the door locked/unlocked without any issues. The only error code was 9E (x01) and someone in the comments stated voltage. The weird thing is that if we persist long enough, change the settings a few times over and over, it will eventually start. Again, we hit start on any setting and it just beeps, similar to the door being open. Any thoughts on what else to check, please let me know.
Same issue with mine
I have the same issue. Did you figure it out?
Hello I changed my pressure switch as well as the inlet water valve it has been working great for about a week and this code popped up LE AND IT SOAKED MY FLOOR :( any help appreciated
Is C6 an error code for the WA45T3200AW
Thank you sir
Same washer keeps filling during wash. Changed inlet valve and same issue..
I have a d5 and Fl code on my washer please tell me what that might be
I’m getting the nF code everytime I try to wash on a normal setting I checked drain tube and it’s not clogged I’m stuck what is the fix or how can I clear this code please help
Hey I have this same washer and the Code that it is reading is NF what could that mean
My spin cycle is what's having issues, but my machine test fine, how do see figure out why my machine shakes too much with clothes
I have this exact same washer. I have a DC error code. I've changed the rods and checked the nut in the bottom of the tank. Also cleaned the shaft and bottom of the tank. It said it could to the hull sensor. Can you tell me how I could check this?
Any luck on this? I have the same washer, was getting dc and it would refill and spin again. I just changed the rods and checked the nut. The few loads I have done since changing the rods now doesn’t stop and throw the code. But it never got violently loud before and now it does and just raises the time and refills and spins again.
Great job
Thanks!
Is there a tech sheet inside or do you have to subscribe to Samsung Tech Support?
I have a question if you've got the time. I'm getting error code 9E. The washer will not start any of the tests
Over/low voltage error code, which means washer is getting too much voltage (over 130vac) or too little voltage (less than 110vac)
@@romarioflores863 my 2012 Samsung top load washer is stuck in 9 e-mode?
How can I get it out of this mode
@@firstdowns9516 check the outlet voltage if 120 AC voltage give or take +- 10
@@firstdowns9516 if voltage is good, your main board needs to be replaced
Mines showing a d5 code any ideas how to fix
Mine does not have a delay start. It is a 2021 model
How you know if it's off balance cause mine won't spin it starts than boom boom boom and it unlocks
BEN !!! What I don't understand is why testing will show everything is fine then when I go to put it on a cycle it runs and will run up to a certain point and then just sit on a number and not do anything!!
Because the error and diagnostic system in Samsung washers is just awful. Most other brands have more robust tracking and logging of codes, and Samsung gives you a few vauge ones that are lucky to work.
mine stopped spinning . it does not start either. whats wrong
I have the same model and it agitates fine until the load is wet and may be heavy. Is there a sensor or something to replace?
Try to spin the plate freely by hand when its not running. Is there any resistance from the plate? If it spins too freely, the plate may have stripped against the spline/gear of the washer, so when there's tons of water/clothes, it just spins on the gear splines and never actually moves.
Great video. I have Samsung wa48h7400aw/a2. It stopped draining so I ordered the drain pump. In the 2 days it took to get the pump, it stopped filling. I changed the pump and it still doesn't work so I changed the inlet valve and still, it won't fill.
I was getting a 4c error and when I entered the test mode using this video, I got error JC-0E.
Any idea? Any help is greatly appreciated. Thanks in advance!
Not an error code it is unit’s version
We have a 3E error code that always comes up. Thoughts on what we should do?
Did you get answer on this?
hi ben . thanks for the video..i have a wa422prhdwr/aa02. once i turn it on it start drainig and throw me the IE CODE.. manual said water level sensor is bad ....i unhook it and blow in it ; i can hear the diaphram working . what do u think. thanks again
Blow in the plastic tube while holding closed the other end of the hose to check for any possible cracks/air leaks in the hose. If there are any, replace the hose.
12:52 it's spinning from 0 to 800 in a minute
Is it possible to get the test procedures in written form? Where do I get them. I have the newer machine.
You'd need to get them from Samsung. Find your model# and see if you can find a SERVICE manual online or a Technicians manual (not the homeowners manual). They may vary slightly from model to model.
i cant enter diagnostic because it sais DS/D5 when i try cant fix tried everything dont know what to do
I'm getting 11e error code. Any suggestions?
I have this washing machine. As soon as I turn it on the drain pumps comes on moment later the error code 1E shows and the drain pump continues to run. I poured water into it and it is definitely pumping the water. All you other test worked but must do it fast or the Pumps starts again and the 1E code comes on
If the pump is ALWAYS on, then the pump relay on the board is stuck. Unplug the unit, and take a screwdriver. Use the handle to gently tap all the relays. Go over them a dozen times each. See if it stops. This should solve it, but likely temporarily... Its gonna need a board replacement as some point.
Hello Ben, ifthe code is Dr or d5 we notice door is not locking
Replace the door lock. Sadly I don't have a video on that right now.
@@bensappliancesandjunk thank you for responding
Code error dc ! Always restars spin/wash mode ! *diagnostic mode ** When on SP mode and tap spin it indicates Te ?!
I have a brand new washing machine and whenever I hold the start button all of the lights blink and then it makes a draining sound. What can this be?
You’re holding it for too long
Tengo una lavadora igual ya hice todo el procedimiento y sigue igual no llena la tina menos de la mitad de agua
Amy suggestion on fixing error code 3e
Motor error code
Nice video ! Hey so my motor works drain pump works in test mode. Machine won’t drain on normal mode I took entire machine apart literally . Wiring looks good will a board reset make it work? And if so how do I reset it? Love your videos very very detailed! So I worked on it today and no codes pump works now one issue I have is when it rinses it becomes out of balance and it stops it with no code . If there was 9 mins left it restarts that section to 17 mins again over and over and over. Wonder if it’s due to not having the update of 2A mine says 28
I have exact the same washer and error code. I changed 4 rods and fixed my problem. That is about three years ago. Now I have nF code.
@@xpan5694 opened up rods and inserted hard rubber to make them stiff in center of white plastic. And that sucks nf code water supply valve clogged maybe?
@@xpan5694 mind telling me where you got the parts? Having the same issue
So I get the nF code. Any idea how to fix this? Because when I wash my clothes on 'Nornal' it certainly fills up with a lot of water and does everything untill it needs to spin...once it gets to that point it just stops, gives me the nF error code and my clothes are all humid still😫please help meh.
Side note. It gives me the same error when I put it on 'Spin', not sure if it needs water to only spin....but yeah
I have the same issue did you find a fix ?
@@adrianmunoz8159 No unfortunately, went and bought a new and different one
My washer is not falling up with water and not spinning You can hear the motor working But no water is going in the machine
How to reset the water level
I have the same washer and clothes still wet and ur still pop on the screen
What dc code
I am getting a 5s code
Hi bens i would like to start a small business like this where i can get all this appliance. thanks in advance
I have videos early on when I made this channel that talk about getting appliances and fixing them up. I'd watch them a few times.
I have 8E code
This washer is white
hello, how can I balance my samsung washing machine
Check and make sure unit is level. Then check underneath the wash plate to see if the washer bracket underneath is in good shape. If it is, likely bad suspension rods.
@@bensappliancesandjunk what can i do to calibrate
@@bensappliancesandjunk It is the same washing machine as the one in the video.
the video is good and bad, good for troubleshoot info but bad that the washer your using is working with NO errors.
Yet that shouldn't change much in that the only difference is that you'd use the jog dial to find them. The error code manifest is included in the video.
800rpm
I have a question
ok?
@@bensappliancesandjunk My error code is PC1, Sam song top load washer what is that era code I’m thinking it’s the gear case
How do i Reset the system? I have an issue where i have to power on/off around 15 times before it actually starts to wash.
it will sometimes even get stuck and go to a pause mode mid cycle sometimes. Even after i power off and power back on, the mid cycle is still there.
also, the error code is 9E. i tried doing the tests you advise but not responsive. I can get it to work by doing like i have been (power on/off around 15 times)
Honestly sounds like the control board is dying. Otherwise, unplug the washer, let it sit for 30min, then plug back in.
@@bensappliancesandjunk is it worth just replacing the Control board and installing it myself or just buy another washing machine? I've unplugged it before for about 10 minutes but no luck, but i'll try 30min now. Thanks for the quick reply
This is my problem also. Cannot find much on 9E error code. Did you ever resolve this issue? Most recently, machine is stopping mid wash.
Please help me wit my too-load washer it show the “NF” code.
Once it gets filled up with water and it’s time to start washing, it stops and the code comes on.
Nf is a water valve code. If its filling ok, is it overly hot water like thr temperature is reversed? It could be the hoses are reversed or the valve sensor is bad
This is so excruciatingly slow
Talk way too much dude just get on with it
Forreal though dislike and no sub.
Thanks so much! I was about to replace washer and this video helped me diagnose bad drain pump. All good now 👍
I changed the suspension rods and the machine when in spin mode goes crazy and it won't finish spin cycle I check the nut in the middle of the drum and it's tight when the machine is off the drum is tight but when it goes into spin it just goes crazy what could it be causing this any help will be greatly appreciated Thank you
I know you posted this 10 months ago. What I did was install the new upgraded Samsung suspension rods for the drum and it fixed the problem. Ran good for 3 years so far.
I didn't have any issues pop up while going thru this video with u, but before, I was getting an NF error code. The barrel is slow to start spinning, but it did go to the same RPM urs did. U did amazing going thru it slowly and thoroughly. Even a newbie like me was able to follow along easily.
I still own one of these..hahaha..thanks for the video..I found out I have a pump problem..
I have a machine that just spins and refills over and over....
Same problem with mine. It even started adding water when I set it to just spin. Resets over and over and eventually gets dc code and stops. Did you ever get yours figured out?
Thank you so much! I’ve been looking for a video just like this To help me out!!
With the error codes I get an upside F and E on the bedding. When in the test cycle the same code pops up flashing and beeps every few minutes. I also get nd when I run a normal cycle.
Hello I get a code of 9E on quick test mode and it won’t spin or do anything. Help what does it mean