How To Use Diagnostic Mode On A Samsung Washer To Fix Any Issue!

Поделиться
HTML-код
  • Опубликовано: 23 дек 2024

Комментарии • 210

  • @amys76
    @amys76 День назад +1

    Wow this is the first video that actually helps

  • @jaspreetgrewal8872
    @jaspreetgrewal8872 7 месяцев назад +18

    The machine was bouncing so much and when we ran to check on it, after that it stopped spinning. kept trying to do spin cycle to test it and it wouldn’t work. I copied you doing the diagnostic test and then it started to spin again. thank you so much for all of your help‼️‼️ just saved me a lot of money 💕

  • @Break.bread504
    @Break.bread504 3 месяца назад +5

    Wish I could like this 100000000 times. Thank you so much!

  • @Plantpoweredgoddess
    @Plantpoweredgoddess 5 месяцев назад +77

    Biggest POS we ever bought! Had ours for only two years and will never buy a samsung washer again.

    • @bjishername
      @bjishername 4 месяца назад +2

      Did you take the machine back to where you purchased it? If not, why not. Did you get a warranty? Did you install the machine yourself? If you installed the machine yourself, did you let the store know this important information?

    • @dirtycasper
      @dirtycasper 4 месяца назад

      ​@@bjishername exactly. They come with a ten year warranty

    • @Leo-gt1bx
      @Leo-gt1bx 4 месяца назад +5

      @@dirtycasper You mean the motor does...

    • @dirtycasper
      @dirtycasper 4 месяца назад +1

      @Leo-gt1bx Yes, but they never said what the problem was. Plus, they come with a one year manufacturer warranty. Sometimes, you get a better one depending on where you purchase from. They left out too many details. I've had my set for ten years now and only had to replace the heating element in the dryer. Which I replaced myself with the help of yt.

    • @maddyrussell1986
      @maddyrussell1986 4 месяца назад +1

      I recalibrated mine and it washes my clothes very well, i have to spin medium loads, but its working great for now at least 😂❤❤

  • @leialeonard2726
    @leialeonard2726 2 месяца назад

    Thanks! Could you answer something for me? My washer takes 2 hours to do a quick wash and we can't figure out why.

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад +3

      It's a bit hard to diagnose without looking at it, but it could be your suspension rods are beginning to wear out. Samsungs will typically add more water and time to attempt to fix a balanced issue caused by bad rods.

  • @TOOL1023
    @TOOL1023 6 месяцев назад +4

    Thank you for this video. Helped us diagnose our washing machine with a drainage pump problem.

  • @brianmurphy5543
    @brianmurphy5543 2 месяца назад +1

    Thank you so much for your help fixed it in 15 minutes your content is amazing keep up the good work

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад

      Glad I could help! Comments like this keep me going!

  • @jcjewell
    @jcjewell 8 месяцев назад +1

    Very informative video, although the “delay 17hr” process doesn’t seem to work for our Samsung WA5451. Any suggestions?

  • @dsphotos2012
    @dsphotos2012 2 месяца назад +2

    Thanks for sharing! Btw my cold water line is not working , will the washer still work with hot intake line only ?? It cost seem to fill the water

  • @MariaMorales-mk9wy
    @MariaMorales-mk9wy 6 месяцев назад +3

    Mine keeps flashing on the CO, nothings coming out so I know that’s the problem, but will it still move on to the next thing it needs to test or just keep flashing?

  • @lapdbombsquad322
    @lapdbombsquad322 5 месяцев назад +3

    Good video, but have a question since you mentioned suspension rods. I get UB all the time. Samsung repair replaced the suspension rods about 6 months ago, and I'm back to getting UB errors very consistently. Thing is, the machine is not shaking crazy or anything. It doesn't seem out of balance in any bad way. And with Samsung there is not pure spin mode, its still adds water and then UB again. Some loads end up taking hours! So, have you found a more permanent fix to the suspension rods? Or there has to be a sensor that is being tripped when it thinks its unbalanced. Maybe that is bad??? The repair guys samsung sent were not very good, but now its out of warranty.

    • @maddyrussell1986
      @maddyrussell1986 4 месяца назад +1

      Mine was doing the ub code, i made sure all 4 feet where screwed down tight on the bottoms, then i shook my washer to make sure its sturdy, after i recalibrated it and it reset the barrel. I then spin smaller loads after washing. Sux but it works for me until the repair man comes. Recalibrate empty and turn on washer and hold down DelayEND and Temp. buttons at same time.

  • @adilshaikh1608
    @adilshaikh1608 8 месяцев назад +1

    Thanks for the informative video! I have the same machine with active waterjet. The model number is different though. I am getting a 3c3 error code that does not go away after resetting the wire connection. Can you advise what must be going on?

  • @NashvilleEdStefanov
    @NashvilleEdStefanov 5 месяцев назад +1

    Do you have any Video's on how to remove the top cover to replace the Suspension Support Rod DC97-16350C on the WA51A5505AV/US Model top loader?

  • @ralphhunt8007
    @ralphhunt8007 3 месяца назад +11

    Those suspension rods do not go bad or need replacing. It’s that dang Lithium White Grease they put on the rod….which is not true grease at all, but is a extremely sticky gluey substance . Over time this gluey substance gets so thick and sticky that the spring cannot monuver up and down the rod as it should, so the computer shuts the machine down because of wobbling. If your tub starts wobbling, just remove the rods (one at a time) and soak them in gasoline. The glue will come off. Replace the white glue with “regular bearing grease” onto the rod, and replace the rod. Then take out another rod and do the same until all four rods have been cleaned and greased with regular “bearing grease”. The wobbling will be gone. DO NOT put Lithium White Grease back on the rods. If you do, in 2 or 3 years ( or sooner) you will have the same problem again.

    • @DuctTapeMechanic
      @DuctTapeMechanic  3 месяца назад +3

      I am planning on making a video on how to use dampening grease on rods to repair them!

    • @fjru4325
      @fjru4325 3 месяца назад

      Will try this

    • @fks-pv8il
      @fks-pv8il 2 месяца назад

      Trying this right now!

  • @spiritualinstincttarot
    @spiritualinstincttarot 2 месяца назад +1

    I followed your instructions, If my washer has the "Co" do i need to get new hoses? Cause u said change ur vales, not sure what that is I'm a women lol because my hose have a leak from the cold water one

  • @angelab6632
    @angelab6632 5 месяцев назад

    At 1:30 into your video you hold the start button and get the typical Samsung start ring. On my machine, I only get half the ring and the machine will not allow me to go any further. I have replaced the front control board. Do you have any suggestions? Thanks

  • @kellyrivenburgh4090
    @kellyrivenburgh4090 2 месяца назад

    Thanks to you my washer is now working you saved me thank you so much for sharing this info

  • @alvinnelson9060
    @alvinnelson9060 3 месяца назад

    Thanks!

  • @joelatatederks4841
    @joelatatederks4841 Месяц назад

    I'm getting a 4C error code. I watched your video but im.not sure which faucet is cold and which is hot. I have a green and a blue faucet and it appears the green faucet is striped because water is draining from it..what do I do

  • @bee21ful
    @bee21ful 10 дней назад +1

    Hi. My Samsung top loader keeps on pouring water inside and then overflows, even the setting is of extra low water level. Plus takes ages to spin. How to resolve the issue?

  • @JaniaNew
    @JaniaNew 5 месяцев назад +1

    Mone does great through test modes spin and all. But when it i have laundry in it totally off balance no mater what. Do i need to adjust the legs

    • @maddyrussell1986
      @maddyrussell1986 4 месяца назад

      Screw legs down is easy just twist each until tightened down to floor. Then recalibrate your washer empty. Theres a video by another guy on here how to recalibrate the barrel.

    • @maddyrussell1986
      @maddyrussell1986 4 месяца назад

      Also sux but wash smaller loads

  • @colinmoore68
    @colinmoore68 4 месяца назад

    Thanks for posting, mine did not go into the AS mode and the door did not lock, so is it reasonable to assume that is the main suspect? The machine stopped in the middle of a wash cycle and would not advance to drain, unplugged and got lid open to wetvac out. The door does not lock in any setting now.

    • @DuctTapeMechanic
      @DuctTapeMechanic  4 месяца назад

      I would also suspect the door lock to have failed. Good troubleshooting.

    • @colinmoore68
      @colinmoore68 4 месяца назад

      @@DuctTapeMechanic Update, I installed a new door lock, and it still does not work. It does not do anything other than allow to change settings, still no testing modes as the lock does not activate I presume. Power is getting to the new lock. Any ideas from here, it is difficult without it showing any error message.

    • @GmanGggggg
      @GmanGggggg 4 месяца назад

      @@colinmoore68did you get it to work at all? I have the same exact problem and at my wits end 🙃

    • @GmanGggggg
      @GmanGggggg 4 месяца назад

      @@DuctTapeMechanic ⁠​​is there a solution to this problem? Washer was working fine and I don’t wanna replace it if I don’t have to. Thank you in advance for taking the time to answer.

    • @colinmoore68
      @colinmoore68 4 месяца назад

      @@GmanGggggg That is so frustrating. It sounds like you already changed out the door lock mechanism, so try to calibrate using this sequence: ruclips.net/video/sBhQ0jU_9jI/видео.html Basically turn on, then simultaneously press and hold the Temp and Delay End buttons, should display as Cb then the washer should go through short tasks. Good Luck and let me know. The washer I was trying to fix was sent to the dump!!!!

  • @SaladMohamed-n5h
    @SaladMohamed-n5h 8 месяцев назад +1

    Thanks but if there’s is problem example drain pump which code I will see?

    • @angelisone
      @angelisone 7 месяцев назад

      ATG's nd will displays

  • @AlexLittle-u6l
    @AlexLittle-u6l 6 месяцев назад +9

    My Samsung washer does not have Delay End. So now what? It is out of balance and I have replaced the torsion rods 4 times. About to make a Boat anchor out of this Samsung washer and buy another brand.

    • @AllGoodThingsFindJT1
      @AllGoodThingsFindJT1 6 месяцев назад +2

      Nyo dampening grease it's super sticky place top of the spring and top of plastic piece onto of the spring

    • @richardarmstrongii1232
      @richardarmstrongii1232 6 месяцев назад +1

      Exact same here . Exact same thing.

  • @stargasmgaming
    @stargasmgaming 5 месяцев назад +1

    now when I try to get into error code mode for (AS)... it wont move past (AS) does that mean there's no codes or history?

  • @janicehendrix4496
    @janicehendrix4496 8 месяцев назад +3

    Does this work on a front loader?

  • @ceciliamoreno1981
    @ceciliamoreno1981 3 месяца назад

    Do you how to fix when it won’t let me change the type of was or non of the buttons work other than the power button? Thank you in advance

  • @JuanHernandez-yk1mx
    @JuanHernandez-yk1mx Месяц назад

    Hello, I have a washing machine of the same model, and from one day to the next, it stopped working-it doesn’t turn on. The outlet it’s plugged into is working, so I’m not sure what it could be. I’ve checked, and the power cord is carrying electricity, but I don’t know what else it could be. Do you have any idea what might be wrong with this type of model and why it’s not turning on?
    I would appreciate your response.
    Thank you

    • @DuctTapeMechanic
      @DuctTapeMechanic  Месяц назад

      That sounds like an issue with the main control board

  • @bernardoaguilar826
    @bernardoaguilar826 7 месяцев назад +5

    We unplugged our for days.. and plugged it back in and it’s acting up doesn’t want to finish the loads stops with a 4C code and beeps until it turns off?!?? HELP!!!

    • @samw7419
      @samw7419 7 месяцев назад

      No water flow error.

    • @hollymoses1524
      @hollymoses1524 5 месяцев назад

      @@samw7419how’d you fix it? Mines doing the same. I disconnected and cleaned the lines and intakes, but not by fully talking the top of the machine off.

    • @nivardomartinez1708
      @nivardomartinez1708 3 месяца назад +1

      Same here, did you guys figure out?

  • @17reasonstokeepfighting58
    @17reasonstokeepfighting58 4 месяца назад

    I have the same exact unit that you worked on in this video. I have had it for 4 years approx. and I continously get unbalanced load codes during spin cycle unless I physical arrange items evenly across the bottom of the tub. I ran the both diagnostic modes like you showed in this video and I have only Unbalanced codes stored. In your opinion do you think my suspension rods are worn out?

  • @hliltootm8389
    @hliltootm8389 16 дней назад

    Do you have a DIY to fix the latch on a Samsung?

    • @DuctTapeMechanic
      @DuctTapeMechanic  16 дней назад +1

      Yes, i do. Here you go:
      ruclips.net/video/5lpu2X3tmsg/видео.html

    • @hliltootm8389
      @hliltootm8389 16 дней назад

      @ thank you for the quick reply!

  • @TipSims
    @TipSims 4 месяца назад

    This helped get my machine up and running. Thank you!

  • @deitracrenshaw5586
    @deitracrenshaw5586 Месяц назад

    I have the Samsung aqua jet and it wont do the self test?? I did exactly what you said and it wouldn't work. it looked like it was going to but never did. any ideas?

    • @DuctTapeMechanic
      @DuctTapeMechanic  Месяц назад

      Strange. If i get one in the near future, I can do a diagnostic video on that as well

    • @deitracrenshaw5586
      @deitracrenshaw5586 25 дней назад

      @@DuctTapeMechanic your more than welcome to practice on mine! LOL!! thanks anyway!

  • @ironmichael85
    @ironmichael85 8 месяцев назад

    I put it in automatic test mode, and it flashed “1” for a minute and then showed 9C2. Would I be correct in assuming that the it won’t cycle thru the automatic tests because the board is bad?

  • @Tommyboy32
    @Tommyboy32 Месяц назад

    Why does my machine fill with water during the test mode and not when I try to start a wash cycle? Error code was 4c but all I can find is stuff about water supply and hoses which is all good.

  • @Azucenation
    @Azucenation 2 месяца назад

    We bought one from you a few months back. It started shaking violently. I think the suspension is broken. Would you come and fix it?

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад

      Can you contact me via fb messenger or offer up. That way, I know who this is and which machine it was.

    • @Azucenation
      @Azucenation 2 месяца назад

      ​@DuctTapeMechanic , how do I find you? My ex was the person who purchased it. We are in woodland

    • @Azucenation
      @Azucenation 2 месяца назад

      By the way it's the same washer in this video

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад

      @Azucenation can you give me your phone number. I can message you. After that I will delete the comment from youtube

  • @diannabartell5964
    @diannabartell5964 2 месяца назад

    hello my issue is i push spin only and it still fills up with water again and again and again. even when i take out part of the load thinking it was to full. uggg any suggestions?

  • @无肉不欢-t7k
    @无肉不欢-t7k 6 месяцев назад +5

    I copied your first step there is no AS code shown and no any water coming. Could please make a video to show how to handle this problem? That will be help all of us who had Samsung wash machine

    • @Angel-sj4rh
      @Angel-sj4rh 6 месяцев назад

      Hello, same issue. Did you ever figure it out?

  • @vramzee
    @vramzee 2 месяца назад

    Hi! My Samsung washer has been beeping nonstop during any wash. No error codes, just beeps. Any idea as to what that may be?

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад

      That's strange. Try unplugging it for minutes, then starting a cycle

  • @mikemay7701
    @mikemay7701 2 месяца назад

    I really enjoyed this video. It was very helpful.

  • @Twerp70
    @Twerp70 14 дней назад

    When I turn my washer on it says Failed power. However, I washed a load of clothes without a problem. Can you tell me why it says failed power.

  • @serigabe6452
    @serigabe6452 3 месяца назад +1

    PLEASE HELP....My Samsung wa52m8650av/a4...half fills up and instantly starts draining.

    • @DuctTapeMechanic
      @DuctTapeMechanic  3 месяца назад

      Seems like an issue with the pressure hose. Make sure it is plugged in!

  • @damarisjimenez6342
    @damarisjimenez6342 3 месяца назад +1

    Thank you saved me lots of money .

  • @coquitampa
    @coquitampa 6 месяцев назад +1

    Hi there thanks for the videos My washer is Samsung also same model and has spinning problem. my washer is 2 years old. I'm smh..

  • @jermainedavis8727
    @jermainedavis8727 5 месяцев назад +1

    Thanks a lot your informative knowledge is most appreciated

  • @jenmarts8844
    @jenmarts8844 22 дня назад

    What does it mean if it doesn't switch to testing hot water or other steps.

    • @DuctTapeMechanic
      @DuctTapeMechanic  22 дня назад

      Does cold water come out when it is testing the cold? If not then the cold is bad and the valves need to be replaced. Sometimes, when the cold is bad, it won't move to next step

    • @jenmarts8844
      @jenmarts8844 18 дней назад

      ​@@DuctTapeMechanicyes I get cold water. It keeps filling and does not switch to testing the hot water

  • @LindaSelby
    @LindaSelby 10 дней назад

    What if my machine won’t go into the error code mode? I need help

  • @adityarazz5812
    @adityarazz5812 5 месяцев назад +1

    My Samsung washing machine top load having issues whenever I turn on all lights blinking and it’s not working.. please help if anyone know about this issue

  • @jessicadeleon4698
    @jessicadeleon4698 6 месяцев назад

    Hello, I have the same washer and it is locked, not child locked but locked is there something i can do about it??

  • @diondc9673
    @diondc9673 6 месяцев назад

    I try what u showing in the video step by step but my delay button not working to bring the number to 17 still stuck on 33

  • @user-tx9gs5ef8o
    @user-tx9gs5ef8o 2 месяца назад

    Changed the suspension rod but the same. Double checked, and suspension rod was installed right

  • @MariaMedina-xg4pj
    @MariaMedina-xg4pj 8 месяцев назад

    Washer still displays ur when a small load is spinning could it be my rods I need to change ?

  • @rossboyd2272
    @rossboyd2272 3 месяца назад

    Mine is eight years old, it’s been a great machine but right now it pumps full regardless of size load and then pumps filling at same time. I have turn water off stop or pause open lid and then close it and restart turn water valve back on and it runs through cycle

  • @melissagreear6353
    @melissagreear6353 Месяц назад

    How do I replace the drive belt on this washer?

    • @DuctTapeMechanic
      @DuctTapeMechanic  Месяц назад

      This washer does not have a belt as it is a direct drive machine

  • @Jose-xb6st
    @Jose-xb6st 6 месяцев назад

    Mine get a U6 code and doesn't get into the draining cycle. I have to manually setup the drain. It's really frustrating.

  • @Leo-gt1bx
    @Leo-gt1bx 4 месяца назад

    I am getting this symbol :- and nothing else. Any idea?

  • @bigkat217
    @bigkat217 5 месяцев назад

    mine only shoots out cold water no matter the setting. i havent run the test mode yet. Actually is there even a test mode on it?

    • @DuctTapeMechanic
      @DuctTapeMechanic  5 месяцев назад

      Sounds like a bad hot water valve. Easy fix

    • @bigkat217
      @bigkat217 5 месяцев назад

      @@DuctTapeMechanic but why is cold coming on when the hot should?

  • @cindyceleste5911
    @cindyceleste5911 Месяц назад

    I, i have same machine ans she is not spin correctly. She does bang bang and error code UB.
    WHAT is the problem !?

  • @mollieanderson9821
    @mollieanderson9821 Месяц назад

    When I hit the start button after delay end, AS doesn’t show up

  • @ProsperityPathway101
    @ProsperityPathway101 2 месяца назад

    Thank you, this was so helpful. 🙏🙏🙏

  • @Parris-ju6yb
    @Parris-ju6yb 6 месяцев назад

    Hello, I’ve replaced the suspension rods (all 4) and still getting the UB close to the end the wash. Any additional advice to fix the machine?

    • @DuctTapeMechanic
      @DuctTapeMechanic  6 месяцев назад

      Are you using Amazon rods? If so, try getting them from appliancepartspro.com

    • @Parris-ju6yb
      @Parris-ju6yb 6 месяцев назад

      Hello, yes I purchased them from AMZ. The appliancepartspro should be the difference?

  • @karengraham3757
    @karengraham3757 Месяц назад

    Mine bunch a lot when its time to spin dry and shows a QR code , I google it and it says the tub is not balance what can I do

    • @StevenPadilla-f8q
      @StevenPadilla-f8q Месяц назад

      That's when you want to connect your machine to your phone right? What's it doing again?

  • @jimlelan4906
    @jimlelan4906 2 месяца назад

    How do you do this if the washer won’t turn on when the machine will not power on when you push the on/off button?…

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад +1

      That sounds like you need a new control board

    • @jimlelan4906
      @jimlelan4906 2 месяца назад

      @@DuctTapeMechanic That is what I was thinking.. Thank you so much for getting back to me!

  • @wouldntyouliketoknow6587
    @wouldntyouliketoknow6587 3 месяца назад

    My code is 0t. I can't get it to go passed AS in error code

  • @AmandaHuerta-oo9xn
    @AmandaHuerta-oo9xn 7 месяцев назад +1

    When it goes to spin mode it’s bouncing all over what do I do then

    • @DuctTapeMechanic
      @DuctTapeMechanic  7 месяцев назад +1

      Replace suspension rods

    • @brychel62009
      @brychel62009 6 месяцев назад

      Mines same way but it is normal through whole self clean cycle no bouncing normal spin

    • @brychel62009
      @brychel62009 6 месяцев назад

      I have to turn it off when it reads ub and then put it on spin only and it gets to 9 and starts going ub again

  • @xxdavidduranxx
    @xxdavidduranxx Месяц назад

    mine stoped while draining it did not train where is the video your talking about please and thanks in advance

    • @DuctTapeMechanic
      @DuctTapeMechanic  Месяц назад +1

      Here is the video on how to fix drain issues on Samsung washing machines.
      ruclips.net/video/wrNzIpBsSfA/видео.html

  • @ryanmurphy1985
    @ryanmurphy1985 4 месяца назад

    How do you do it for a Samsung front load washer?
    Model # WF45N5300AF/US

  • @elcuhhangel1968
    @elcuhhangel1968 5 месяцев назад

    Mine doesn’t say AS it won’t do anything automatic mode or the other mode won’t do nothing my washer went bad with clothes and water inside when the storm came and power went out

  • @anthonygonzalez4704
    @anthonygonzalez4704 Месяц назад

    What does 3C4

  • @jessikacisneros8083
    @jessikacisneros8083 5 месяцев назад

    Samsung smart app show diagnostic. Cleaning drum i did clean it still shows

  • @SALMANDER33
    @SALMANDER33 4 месяца назад +1

    How do i fix my DC1 code ?

    • @DuctTapeMechanic
      @DuctTapeMechanic  4 месяца назад +2

      Sounds like an issue with the door lock mechanism. I have video on how to replace it on a Samsung.

    • @SALMANDER33
      @SALMANDER33 4 месяца назад

      @DuctTapeMechanic it was exactly that replaced today took about 45mins and washer works like it should! I'm doing the upgraded spring rods next. Your video was extremely helpful and this washer is soo easy to work on and it's awesome to have the ability to self/auto diagnos or manual diagnos epic !

    • @Nortrin
      @Nortrin 3 месяца назад

      @@DuctTapeMechanicI cannot find that video

  • @josejm556712
    @josejm556712 6 месяцев назад

    my washer shows the code 9c8 what can i do to fix it

  • @Cinmaki
    @Cinmaki Месяц назад

    where is the filter to clean out? I don't see it on the front or the back.

    • @DuctTapeMechanic
      @DuctTapeMechanic  Месяц назад

      In order to get access to the water filters, you will have to turn off the water and remove the hoses and then pull the filter out from the inlet valves and clean them.

  • @6spd85notch
    @6spd85notch 6 месяцев назад

    Mine won’t drain. Entered test mode and it stopped at drain what should I do?? It’s full of water also ?

    • @DuctTapeMechanic
      @DuctTapeMechanic  6 месяцев назад

      Check for clogs in the drain system, and if there are no clogs, then replace the drain pump. I have a video on that on my channel as well

  • @SaladMohamed-n5h
    @SaladMohamed-n5h 8 месяцев назад

    How can I contact you if need help?

  • @RosemarieDavis-y5n
    @RosemarieDavis-y5n 4 месяца назад

    How to fix the lidlock

  • @amybaker5712
    @amybaker5712 8 дней назад

    I’ve had this washing machine for over 5 years and recently it would stop saying unbalanced during spin cycle every time! I’ve tried rearranging the clothes and all. Did this test and it passed everything. Even recalibrated it. So idk!

    • @DuctTapeMechanic
      @DuctTapeMechanic  8 дней назад

      Most likely bad suspension rods. It's a notorious issues on these models

  • @tedthornton7791
    @tedthornton7791 7 месяцев назад

    The same model you have on here. Except its white.
    Problem: Alternating flashs 113 and 42..

  • @ReAnnRing
    @ReAnnRing 26 дней назад

    wow - had no idea ... thank you!

  • @roble6177
    @roble6177 6 месяцев назад +1

    In test mode, the cold and hot water run just fine, but when I put it into wash mode, the water doesn’t run

    • @DuctTapeMechanic
      @DuctTapeMechanic  5 месяцев назад

      That sounds like an issue with the control board....

  • @HectorG951
    @HectorG951 2 месяца назад

    I just changed the suspension rods and it still goes on unbalanced then I recalibrate then it’ll do it again on a random load why? Anyone?

    • @marioarellano5915
      @marioarellano5915 2 месяца назад

      I change the suspension rods and it’s still bad

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад

      Make sure the tub nut is tight.

    • @SPOWNER22
      @SPOWNER22 2 месяца назад

      hi! if you havent done so try putting the clothes around the white part not right in the middle . i think that helps with the balance

  • @reneilweramolotja8160
    @reneilweramolotja8160 7 месяцев назад +1

    Hey my machine is on sc top loader

    • @DuctTapeMechanic
      @DuctTapeMechanic  7 месяцев назад

      Here is my video on how to deal with a Samsung toploader with drain issues.
      ruclips.net/video/wrNzIpBsSfA/видео.html

  • @mortezazarinkamary4058
    @mortezazarinkamary4058 2 месяца назад

    How to fix 4c error after checking all water pressure and inlet and outlet

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад +1

      @@mortezazarinkamary4058 replace inlet valves

  • @vivianlang6377
    @vivianlang6377 Месяц назад

    This does not work for my Sansung Top Load AquaJet Washer. :(

  • @Moemoe6961
    @Moemoe6961 7 месяцев назад

    The test part ran fine but the error code part didn't show anything.

  • @jonjackinsky1002
    @jonjackinsky1002 7 месяцев назад

    Doesn’t work on all. Our wa45t3200aw doesn’t have a delay setting.

    • @tinasturgill2073
      @tinasturgill2073 6 месяцев назад

      Men don’t either so what do we do to do this test

  • @Animeboyz87
    @Animeboyz87 2 месяца назад

    I’ve tried all this and still shakes like crazy When I turn on it stays on spin instead of like normal

  • @rajdonkenyon6192
    @rajdonkenyon6192 3 дня назад

    I did the process pass a5 and no water coming in just dc1 I see

  • @jc7887
    @jc7887 4 месяца назад

    Thanks for this.

  • @damnedtexan1976
    @damnedtexan1976 4 месяца назад

    Mine won't go into error mode!

  • @lindageorge6062
    @lindageorge6062 2 месяца назад

    I can’t get my lid to unlock, help please

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад +1

      Try unplugging it for a few minutes, then start a cycle

    • @veritasfan11
      @veritasfan11 2 месяца назад

      thank you the unpluging for 15 min worked.

  • @izraelmirelez2168
    @izraelmirelez2168 3 месяца назад +1

    Mine is plugged in it has no power please help it just quit

  • @stargasmgaming
    @stargasmgaming 5 месяцев назад

    my problem is mine is not filling with water at all after a single move.... the hot and cold water worked during the test cycle tho. what the heckkk

    • @nicheadlee
      @nicheadlee 3 месяца назад

      I am having this issue as well, mine will fill with hot/cold during the test mode but gives a SC error at step 7 so it won’t drain. On any other cycle it won’t fill with water or drain. I’m wondering if it’s the control board or if it’s the drain pump, the pump is all clear and I took all of that out but it’s like new, no clogs…
      curious if you resolved your issue?
      Thanks

    • @nicheadlee
      @nicheadlee 3 месяца назад

      I swapped out the control board hoping that was the issue but it still won’t drain.
      I might try to switch out the drain pump as a last ditch effort.

  • @mariasantana1047
    @mariasantana1047 4 месяца назад

    Mine it doesn’t work the water jet

  • @jeffoff7795
    @jeffoff7795 14 дней назад

    Mine doesn't ever give me the AS code. Just one more thing that's not working. Pretty tired of dealing with it to be honest.

  • @megansmith3924
    @megansmith3924 2 месяца назад

    Help how do I get it unlocked when it’s in door lock mode it won’t unlock my clothes so I can dry them 🥺🥺

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад

      I would leave it unplugged for a few minutes, then plug it back in and try to start a cycle

  • @dalefarmer.568
    @dalefarmer.568 2 месяца назад

    Awesome thanks ....

  • @vaninec
    @vaninec 4 месяца назад

    I have dC flashing
    no test run

    • @Leo-gt1bx
      @Leo-gt1bx 4 месяца назад

      Any idea why? I had same machine keeps turning off. Diagnostic gives me this :-

  • @clarencebartlett850
    @clarencebartlett850 2 месяца назад

    not any help for my samsung top load washer

  • @daniellestrouse9797
    @daniellestrouse9797 2 месяца назад

    Mine won’t stop running water!!! Even when machine is off!

    • @DuctTapeMechanic
      @DuctTapeMechanic  2 месяца назад

      Never seen that. Sounds like a pressure hose/ stuck valvs issue. I hope you tuned the water off from the valves of the house