Watch this ruclips.net/video/WQMSSNCzlAI/видео.html Amazon: Home printer rex.red/home-printer-all-in-one * Printer Ink rex.red/printer-ink * Printer paper rex.red/printer-paper * Wireless Printer rex.red/inkjet-printers-all-in-one-wireless * Laser printer rex.red/laser-printer-all-in-one * We earn money from qualifying purchases using our affiliate links. As an Amazon Associate I earn from qualifying purchases. Affiliate links are marked with a star. * SHARE this video with your friends + LIKE + Comment + Subscribe to BOTH our channels: rex.red/diro rex.red/rno Thanks to Matt Graham, another tip: When doing this, open the back of the printer so it’s easier.
Revised procedure: USE MICROFIBER CLEANING CLOTH WITH GLAS WINDOW CLEANER. 1) Cut microfiber kitchen cleaning cloth into A4 size. 2) On one rub the window cleaner into the area, were the paper feeder role touches the cloth. 3) Put 20 sheets of A4 paper into the paper tray 4) Put the cleaning cloth on one A4 plastic sheet and put it on top of the 20 sheets into the tray 5) Run at least 5 printing jobs (you always have to reset and restart the printing job.) 6) Turn the cloth with A4 paper 180 degree and run one print job for drying the role. 7) Now… your printer should work again !!
Thanks for the idea. I have used similar double sided tape as in the video, but hasn't risked to let it go through the printer. Instead I cleaned the rollers without turning the printer on. I have attached a piece if tape at the middle of the shorter edge of an A4 paper and moved it a bit back and for in the normal loaded position by hand. It cleaned the rollers gradually. Now my printer feeds perfectly. Thanks again. :-)
6 years later and you're still helping people solving this problem. I didn't have double-sided, so used regular scotch tape and taped several pieces together facing up and then taped them down to the paper on the edges with another piece facing down. It took several passes, but now my printer pulls paper in like it should. Thank you!
OMG, this really worked!!! I was so frustrated!! If you already are on your last nerve, just fast forward to 4:30 minutes in. First I had a paper jam, then the printer just kept mangling each subsequent page ... DO THIS ... Use one piece of card stock paper and a couple strips of small double-sided tape on the card stock. This is the best part ... LOL ... jam this paper in and out to relieve tension (if you were frustrated like me, haha) and the dirt on the inside roller comes off on the tape and then the roller has traction again!!!!! It literally takes 20 seconds (unless you have a ton of frustration to get out!!!!!) FYI DO NOT put that sticky paper on the floor if you have nosy cats .... yep, mine stepped RIGHT ON IT before entry!! Thank you so much for saving the printer from the trash and me from angina!!!
It’s 2020 and this still works, had my crappy work one break and then my home printer had THE SAME EXACT ISSUE. Not only was HPs help video worthless, this video saved me from throwing my printers out a window. I used a lint roller sheet and it was perfect. Thank you so much for this!
Thanks for the tip! I was actually able to reach my printer's rollers with a q tip and some alcohol. I wiped them for a couple minutes, let the alcohol dry for about ten minutes, and it started printing just fine!
the alcohol will dry out the rubber on the rollers with time. condition with a" LITTLE" coconut oil and feed a few pages threw to make sure all the access oil is off the rollers
Thanks man! I didn't try your method since double tape isn't available but it was urgent for me to clean the rollers. With your video, I suddenly got an idea. What I did was: I made the end of a blank paper a little bit wet with water and a bit of alcohol. Just some drops of water on my fingers then spread it on the end. I saw some dirt that the wet end of the paper managed to remove. Then I decided that I should still clean it more, so I put some alcohol on my fingers and slightly wet the ends of another paper. And more dirt removed. The result: feeder roller became more smooth. I don't have to put only one paper one by one whenever I need to print many pages or copies. :)
Someone suggested pushing through a piece of cardboard, scary. I cleaned it with a qtip right now, got some oily mess and now it's working again. Thank you mate.
This totally work!!! Paper was stuck in my printer from the back and I was panicking and searching at the same time for a RUclips video that could help me...Then I found you :)
Works 100% fine. Cleaning with double tape won't damage your printer. what I did: take a thin cardboard (cornflakes box) (cauz paper might tear and jam in printer) apply double tape in the end only (horizontally) let it in and out of the paper tray manually (keep printer off) You can see the dirt in the tape. repeat above step until the roller is clean. and your printer is ready to rock and 'roll'. thank you so much for the video.
This worked for me as well, I didn't dare feed the printer automatically with double sided tape on paper and this manual method is totally safe! (The tape i had at hand is very sticky, meant for carpets)
Shakthi Vel Thanks soooo much for this tip! Worked like a charm. I've been dealing with this problem for a while and I was ready to toss my printer and get a new one.
I used my ruler and tape the ruler with a normal tape because I didnt had a double sided tape and cleaned the roller, and it worked. MAY GOD BLESS YOU!
hey man, just wanted to thank you! i was just about to visit a printer technician tomorrow to have my printer fixed. but your double sided tape gave me an idea. i instead attached a regular tape to a piece of paper and made sure they wouldn't come off easily even if i hold on to the paper so it doesn't go in completely. after a couple cycles doing this, it works now even with just a single paper. thank you man, really really thank you!
Posted 5 years ago and saved my life today!!! Thank you so much for this, I was devastated not being able to load paper and so much urgent printing to do. Thank you!
Please tell me how you used the lint roller paper....its my last resort. I tried alcohol, scotch tape it fed one time. Then I was back to force feeding with my hand. Thanks in advance.
Thanks! Cleaning the rollers is the definitely the way to go. I used a metal ruler with double sided sellotape and with the printer turned off I pushed it back and forth under the rollers. With your other hand use a long flat headed screwdriver to hold down the mechanism which holds the rollers (basically like an aircraft undercarriage) to ensure you get a tight fit when you squeeze the ruler between the platform below and the rollers. Worked for me and no risk to printer.
Yeah, my problem is that my printer's roller has ink on it, which gets in the paper before the actual printing... I'll try your method as it may work in my case!
This video gave me ideas so I appreciate it. I ended up using a pencil, taped a q-tip to it, wrapped tape around the end of the q-tip and ran it across the rollers a few times and that worked for mine!
Thank you so much for this video, I was so focused on trying to reset it and get rid of the error rather than trying to solve the issue at hand. I almost destroyed this printer out of frustration, but this video saved me so much time and gave me such relief. I tried putting the cardboard in and then printing it out and once I did that the cardboard came through and with it included a piece of a sticky note that was jamming it! And afterwards it printed smoothly and perfectly. I cannot express enough gratitude for this video! I have a Canon Inkjet MG2522.
About to buy replacement printer found your video ordered Amazon Prime- 24 hour delivery -double side tape 2inch-cut A4 size small box cardboard sheet stuck length of tape sticky side up on the leading edge-to the edge-then with printer off pushed the cleaning board in and out a few times felt like an inch or so,-easy in tougher out then turned printer on with maybe 30 sheets or so in the loader and Bingo no issue the first sheet went straight in! Job done thanks to you,much appreciated well done! Mike
Thank you so much for the tip ! Instead of using double-sided tape, I used a sheet from a lint roller. Stuck it to the top of an envelope and pushed it under the rollers a few times. And then it just started working again.
Thank you so much for this video! We were about to give up and buy another printer! My husband did exactly as you said, with double sided tape, and it worked like a charm!!! Amazing!
Wow It worked for me thank you so much 😊 . My printer was troubling me for many days finally i searched on RUclips your printer looked similar to my printer so I watched your video 1st . No wasting of time watching other videos😄
The method really works! I used regular one-sided tape, taped down using margins on the sides. I had to pass the paper a few times before it started to work (so probably regular tape is not sticky enough), but after that it correctly fed paper like before.
Thank you so much! I didn't have any double sided tape so did as someone in the comments suggested and used a sheet from my lint roller. I stuck it on to a piece of paper with sticky tape and fed it through the printer just once and it's now working great. Amazing how much dust and fluff came out on the sticky paper!
Just tried the double back tape method & it worked great. I lined up 3/4" strips about 4' long to align with the rollers & ran it through the printer numerous times. After that, I lightly wet the strips and paper along the roller path to help remove remaining dust followed by new, dry paper to remove remaining water, it worked great...printer takes paper perfectly now, thanks for your great suggestion.
THANK YOU, Liked and Subscribed, thank you, I used some duck taped taped to a ruler upside down and it worked!!! Got the ruler under the rollers and it got the dirt off.
I love how all of the comments here are as useful as the video. Thank you for ypur tips! I'm having the same issue on my own printer. Hope this video and/or one of the comments here will help me fix my printer 🤞
I used a piece of lint roller that I use to collect pet hair. Some rollers have removable sticky layers whichs are less strong than double sided bands. Staple the sticky paper on a sheet and get a hold of it to prevent it to be taken into the printer. It worked for me.
Usei uma régua, durex, um cotonete e álcool. Preguei o cotonete na régua com durex e molhei a cabeça do cotonete com álcool. Depois, enfiei a régua pela parte da frente da impressora, até aqueles rolinhos que puxam o papel pra dentro, e consegui limpar a poeira que estava acumulada lá. Depois disso, funcionou perfeitamente :) Thanks for video!
Thanks for the video. I happened to find a "Paint mixing stick" and "Painter's tape" in my garage. I taped a sticky side up tape at then end of the stick. Then used it to clean the wheels with other stick to hold and push down the wheel unit. It works like a charm.
you can make the double sided tape less sticky by repeatedly pressing some material like denim (jeans) on it, or some cloth that doesn't leave bits of fluff.
Thanks. I have a similar printer to you, and your video helped me work out another method. I used some narrow double-side sticky tape on my finger to dap onto the pad at the bottom of the paper tray and the rollers above it. I did this by looking into the printer with the paper tray out as far as it goes for the pad on the paper tray, and by lifting one edge of the printer while the paper tray is out to access the rollers from the underside.
WORKS 100% Thank you very much,mate. It really works just fine. The printer does not have any issue malfunctioning or something, you just need to be a little careful during the process of inporting the double tape-paper. Thank you again. P.S. Canon Pixma MG3150
Thanks! So, I read the other comments and had a think. Was worried about the doubles sided tape and paper getting stuck. So here's my upgrade on your initial great idea. 1. Got a large plastic ruler that was wide enough for to get under both wheels. 2. Double side taped on a strip of cotton (mine from a rag that was daughters old school sports shirt, mix of cotton and acrylic I guess? It has a rough weave) to end of ruler. 3. Soaked cloth in isopranol Alcohol, placed it under the wheels. 4. 'Printed' a blank sheet multiple times, pressing the green button (lower left) each time printer complained there was no paper. 6. Did this about 6 + times ... and lo and behold ! the next sheet of paper I printed worked. NB - the bonus of using the Isopropanol was the double sided tape came off my ruler easily - but it stayed strong enough to not have the wheels pull the fabric off. Hope this adds to this excellent, 'right to repair' video. Too many printers get thrown out that can be easily fixed !!
Wow thank you for the upgrade! Small problem with alcohol on rubber but it would be wiped off the rubber rolls after printing just a few pages so it's fine! :)
Thank you Sir, I saw your video and it fixed my problem nicely. I was lucky to be able to access the rollers so I could feed the paper with sticky tape through manually with my fingers while the printer was powered off. It's a very clever simple solution that many people would not think of.
Really excited about your comment! Makes me very happy! :) It's amazing how easy this problem translates to buying a new printer. Thanks for saving your printer!
You’re a superstar! Thank you! Have been hand feeding paper for a while now....Didn’t have double-sided tape so just taped down 3 strips of regular scotch tape sticky side up and used qtips with alcohol on rollers...(must wait for it to dry!)..working beautifully!
I was about to buy a new printer under absolute frustralition. Your video allowed me to go a step further. Unplug the printer, turn it upside down, my printer had 4 philips head screws holding platic guides, remove 2 guides for the paper tray, removed them, removed the paper tray then peeled the rubbers off the pickup rollers then washed them with brush in dish washing liquid and water, dried with cloth (not tissues, they have oils), reinstalled on the rollers (already could feel the rubbers were more grippy) then reassembled the tray and guides.. Re plugged the printer and whoa, the printer was throwing the paper in.
Thank you! :) I don't think they like these videos. I wouldn't recommend to buy a Canon Inkjet for home use. Make your next printer a laser, HP/Samsung/Brother and it's all good.
Thanks, this helped me, too! Before this video i did not even imagine to check if the rollers are rolling. Once i figured they are, i took a 30 cm ruler and stuck some wide tape around it, sticky side out, and cleaned the rollers with that, further i wrapped that same ruler in an old tshirt that i moistened up and again cleaned the rollers. Seems to be working at least for now, and so happy i dont have to immediately cash out on a new one.
Wow thanks bro. I followed your double sided tape method, but paste the tape on a thicker piece of paper. Works wonderfully. My printer is working fine now! Thanks again bro!
I like your video because it shows the feed rollers spinning and not picking up the paper. I have an MX472 which is very similar in design. I cleaned the front feed rollers using a cotton swab, alcohol, tape, and a stick. I taped the swab to the stick because I couldn't get to the feed rollers any other way than through the paper feed slot and I couldn't reach them without the stick. I vacuumed out the printer as well. Once the rollers were cleaned they picked up the paper.
Thank you! I bought a printer from a garage sale and was about to chalk it up for a loss until I did what was on the video. It worked. I didnt have double sided tape so I tape three pieces sticky side up vertically and attached them with tape horizontally at the top and bottom
Thanks for the tip. I was worried about getting the rollers stuck, so instead I squirted some isopropyl alcohol on the paper A4 sheet to wet it and then pushed it through but grabbed the top of the sheet so that the rollers just spun on the wet paper. This did the trick and now it picks up OK.
Yay this actually worked!! I tried another cleaning hack first with isopropyl alcohol on a wipe taped to a piece of card and that didn't work...so I repeated that with this method, double sided tape over a piece of cardboard, and it picked up some hair (I didn't run it through, I pushed it back and forward whilst it was trying to print a test page). It's just a central roller on a Pixma MG4250, I was so skeptical - it works! It's even picking up my thick cardstock by itself, thank you!
Using this method with less aggressive tape works great. Fed the paper with tape twice thru the printer and have not had feeding issues since then, but maybe some time in the distant future I might need to go thru this process again.
HELP SAVE this CHANNEL and SUBSCRIBE NOW. Dragos Ion RO We need more than 1000 SUBSCRIBERS for this channel to SURVIVE! If already subscribed, please tell a friend to subcribe! Please SUBSCRIBE NOW!!!
I had a paper jam, got the paper out, but now on forms, the lines don't print straight and I have tried doing all the head adjustment and roller cleaning as described in the printer maintenance. Do you have any videos to help figure out how to fix that? I have a Canon MG 3122
No videos but you could try to also remove the cartridges and reinstall them and then do the print head alignment. If still no luck, something is very wrong with it.
Good idea. Thank you very much for this useful and do-able tip. I have the same printer & same problem. I tried to do it with two pieces of double sided tape applied at the end of card paper parallel to the paper edge (unlike your which was along the track of rollers) because I was scared of paper get jammed inside. I did it manually with printer off & then felt a bit confident to run the paper through the printer, switching it ON. To my utter shock, paper went inside smoothly but completely rolled over on one of the rollers bars,close to the outer tray due to the scotch tape adhesion. I did not take the risk of dismantelling the printer to reach that roller bar,so what I did was to cut the paper several times with a sharp cutter (risking the rubber of roller bar) & taking out piece by piece with a long tweezer. I removed the cartridges though. It took me almost one hour to take out the shreds of paper stuck in there. Then I cleaned the roller bar with alcohal. Finally the printer was OK & it worked perfectly taking in the papers smoothly. My advice: Do it manually, while printer is OFF.
Great little video. Very helpful person. I never had a paper jam that I couldn't see from outside and never saw the thingie in back that exposes the rollers. Thanks very much. *****
Thanks man, did the same thing with my Epson Ecotank L3151, and worked like a charm. Keep in mind that Epson in its Ultra Glossy papers includes a special paper with glue to clean the pickup roller. I had some of those that do the job, but i was run out of them.
It really works! I used a very thin and soft ( i mean not too much sticky) double sided tape and printed a blank page several times. even I heard not any strange sound when printing. It just normally printed the taped page and is correctly working after then. Thank you!!
Wow that's pretty nice! Perfume should work well. Alcohol makes rubber dry so don't use too much. If you can find alcohol-free wipes that's even better! That's a pretty cool way to print some love letters. 😁
Multumesc! A mers si la mine (MG3150) Nu am avut banda duble adeziva, asa ca am folosit 3 banzi adezive din hartie , puse (vertical) pe lungimea unei coli A4. Pe mijloc am pus banda cu adezivul in sus si pe laterare am prins-o cu cate o banda.
Great video. I just had to clean the rollers (easy access on my Canon MG5750 just by turning it over and pulling out the paper tray) and instant success. Thanks for pointing me in the right direction
This fix the most front feed printer problem. it seems stuck but when the roller cleared from dust it will feed the paper. i have to do the tape twice to make the roller feed papers smoothly. thanks for the video!
Thank s for this video , I was about to throw away my printer ,but I gave it a try , using a tape and found out a coin stuck on the tape ,when removed it got back to normal work . thumbs up!
I had already tried cleaning the feeders on the paper side, then I saw him trying to force the paper through and tried that. When I did a piece of moss popped out from deep inside the feeding mechanism o.0 Solved my problem in less than 5 mins and I didn't even have to watch the whole video ^^
Thank you so much!! You saved my life! Before this Im waiting one by one paper to feed. After watch this video, it's work! I'm using sticker paper to clean the roller
I have a pixma mx475. For double sided tape i got post-it notes turned it upside down, sticky side up and taped it to an A4 sheet. Sticky enough for this task. While printer was off, pushed it in and out of the roller. Also the pad the rollers sit on gave that a clean too. Thanks for the video great help.
Great video, just like to add a tip, check for obstruction say for example a pen lid🤣 found a stray one in mine causing havoc couldn’t see until I pulled it apart a bit. But might have come out easily if I had turned it upside down. All good now👍
Question! At 4:15 in the movie, when it’s zoomed in, a white part with a spring retracts into the roller. In my printer it doesn’t. It stays where it is and blocks the paper from going further. Any idea about the cause? Thanks for any help! I’m running out of options...
Try to use one sheet of paper and push it in slightly to help it go in. Is that working? Not all printers are the same but the roller should spin and try to take paper.
@@IONHowTo Thanks for the help! In the end, after unscrewing a part on the backside of the printer, I managed to have that white part stay in its retraced position. It may not be able serve its original purpose anymore, whatever it was, but the printer works!
Ended up taping some alcohol wipes to a ruler and sticking that in under the rollers while the printer was doing its cleaning routine. Once the rollers dried out, they started to pick up paper like new. Thanks!
You are genius man...it´s works!...But i did different, i put some paper (sticker letter paper) and put litle talcum powder to reduce the glue and put off the mashine and then i introduce the paper one and other time, maybe 4 times, for the wheels tuch well the paper and fix the problem! Thank you very much!
I wanted to almost throw my printer out of the window until I saw this video. It worked for me. The printer occasionally clicks a bit hard but now he takes the paper. Thanks for sharing.
I looked online and transport cleaning sheets are just very expensive. :( Maybe will try this trick later when I got back from work. Thanks! EDIT: dude your trick worked! it fixed the feeder so now my printer doesn't have problem pulling the paper :D thank you very much!! EDIT2: i actually did the trick 2-3 times (with double-sided tape) to "force" the dust out of the feeder, now i'm a happy man :D
+opsddos Enjoy it :) yeah the original cleaning sheets are for speed ceanup in professional scanners or printers. Try to do it only when its really needed. Cheers :)
HELP SAVE this CHANNEL and SUBSCRIBE NOW. Dragos Ion RO We need more than 1000 SUBSCRIBERS for this channel to SURVIVE! If already subscribed, please tell a friend to subcribe! Please SUBSCRIBE NOW!
HELP SAVE this CHANNEL and SUBSCRIBE NOW. Dragos Ion RO We need more than 1000 SUBSCRIBERS for this channel to SURVIVE! If already subscribed, please tell a friend to subcribe! Please SUBSCRIBE NOW!
Thank you very much! I tried a variation of the dubble sided tape: I glued a sheet of sticky notes upside down on a normal paper. The glue on the sticky notes did the job after a few repetitions.
Hi, I would like some advice regarding my printer if possible. I have a problem with my Canon mp287. Everytime I print, I get a slanted paper print result. I observed the feeding of the paper and saw that the left side of the paper goes in earlier than the right one. I wonder if you have any advice on how to fix this? Thank you!
@@SayomiKamikura try to see if there's anything stuck on the paper transport rollers. You could try to look inside while it takes the paper. Could give you an idea about wheres the problem.
Ok tried it with the instructions. Tape got wrap around the rollers and I thought that's that then. So took pliers to unwrap the tape from the rollers and thought it's not going to work. Guess what, IT DID!! great tip and thanks. Like brand new
OMGoodness...... this technique just pushed out a piece of cardboard half the size of my hand. It was definetly not the uncoloured piece I pushed in as shown and got my TS3160 printing..... how the heck did the coloured carboard get into my printer..no idea ... All good now .. thankyou :)
Paper Feed Issue resolved: Canon MX 472 Should work well for other similar printers. This RUclips video made me take the risk below. I was hoping it would work or throw out printer. Previously used Rubber Rejuvenator, alcohol, water. No luck. This worked. I had to junk 2 printers that I got for free before I did this. My Steps: Took basic file folder and cut to 8.5* 11 similar to basic standard printer paper. Took Product: Touch ‘n Stick Spray Construction Adhesive Professional All Purpose Formula that I had in my shop for many years but can still buy doing an Internet search. Sprayed about ¼ from of the top of the cut file folder. Waved in air for about 5 seconds. Pushed the top of sprayed cut file folder into input tray so that it would move the pick-up roller back and forth about 10 times smoothly and fairly quickly. Do not let the folder just sit touching the pickup roller or bottom of area pickup roller sits, keep on moving back and forth and then pull the cut folder out and away from the printer and into the trash. Walked away for ½ hr. Took my paper feed just fine. After a week still working. Feeding paper and printing. This is my first post to RUclips because I share everyone’s pain and expense.
Just used a flat ruller, on which I fixed with an elastic on one end, a computer wipe. I put then some hydroalcoholic gel (for hands cleaning) on the wipe, to have it more wet. Then I placed the wipe juste below the 2 transport wheels, and using the ruller, I forced the wheels upwards. Then I start a print (copy), the transport wheels turn a bit then stop with the "no paper" sound. I click "Ok" on printer, and then several times again, to force the little transport wheels to turn on the wipe, with ruller still in place and pushing the wipe upwards on the wheels. After 5 or 6 times, I felt the little wheels were drawing more onto the wipe and ruller, so I stopped and waited 10 minutes to dry completly. Then I tried with paper sheets, and the transport wheels were working perfectly as new :) ! Thanks for the idea of doing that, I was about to brick that 8 years MX535, but now it is working yet as new :D
EASY METHOD... Few sheets of paper, spray the end with Isopropyl Alcohol, the run roller cleaner (hold stop for 7 flashes). As rollers go, help paper in a bit if need be, but then hold it in place so rollers spin over the alcohol. Do it a couple of times if needs be. Easy, no mess and the cogs don't go mad clicking like crazy.
정말 감사합니다. 양면 테이프가 없어서 a4 한면 코팅지 필름을 사용햇습니다. 윗부분 5cm만을 벗겨내고 끈적한 부분을 롤러에 닿게 해 밀어넣고 앞뒤로 50번 정도 넣었다 뺏다 하는 식으로 수십번하니 이물질과 먼지들이 코팅지 접착면에 많이 묻어나왔습니다. 그리고 프린트 출력 테스트를 하자 3장 다 잘나오게 되었습니다. 덕분에 수리비가 들지 않았습니다. 당신에게 감사합니다.
Thank you for the brilliant and innovative solution. I used Scotch brand double sided tape and made the pieces about three inches long. It was just strong enough adhesive. Don't forget to open the back of the printer when you run the tape through. Worked perfectly! Subscribed already!
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Watch this ruclips.net/video/WQMSSNCzlAI/видео.html
Amazon: Home printer rex.red/home-printer-all-in-one *
Printer Ink rex.red/printer-ink *
Printer paper rex.red/printer-paper *
Wireless Printer rex.red/inkjet-printers-all-in-one-wireless *
Laser printer rex.red/laser-printer-all-in-one *
We earn money from qualifying purchases using our affiliate links. As an Amazon Associate I earn from qualifying purchases.
Affiliate links are marked with a star. *
SHARE this video with your friends +
LIKE + Comment +
Subscribe to BOTH our channels:
rex.red/diro
rex.red/rno
Thanks to Matt Graham, another tip:
When doing this, open the back of the printer so it’s easier.
Revised procedure: USE MICROFIBER CLEANING CLOTH WITH GLAS WINDOW CLEANER.
1) Cut microfiber kitchen cleaning cloth into A4 size.
2) On one rub the window cleaner into the area, were the paper feeder role touches the cloth.
3) Put 20 sheets of A4 paper into the paper tray
4) Put the cleaning cloth on one A4 plastic sheet and put it on top of the 20 sheets into the tray
5) Run at least 5 printing jobs (you always have to reset and restart the printing job.)
6) Turn the cloth with A4 paper 180 degree and run one print job for drying the role.
7) Now… your printer should work again !!
Thanks for the idea.
I have used similar double sided tape as in the video, but hasn't risked to let it go through the printer. Instead I cleaned the rollers without turning the printer on.
I have attached a piece if tape at the middle of the shorter edge of an A4 paper and moved it a bit back and for in the normal loaded position by hand. It cleaned the rollers gradually. Now my printer feeds perfectly.
Thanks again. :-)
@@ferencfromhungary6723 works great like this with a ruler! I might make a video using a ruler.
That's safer but might need to repeat it few times.
This guy seems to have a really close and caring relationship with his printer.
Huhuhuhu
Lol when you work more with them, you will appreciate printers.
Still a better love story than Twilight.
@@MoAli72 lmao.
HAHAHAHAHAHAAH
6 years later and you're still helping people solving this problem. I didn't have double-sided, so used regular scotch tape and taped several pieces together facing up and then taped them down to the paper on the edges with another piece facing down. It took several passes, but now my printer pulls paper in like it should. Thank you!
Thanks for watching!
OMG, this really worked!!! I was so frustrated!! If you already are on your last nerve, just fast forward to 4:30 minutes in. First I had a paper jam, then the printer just kept mangling each subsequent page ... DO THIS ... Use one piece of card stock paper and a couple strips of small double-sided tape on the card stock. This is the best part ... LOL ... jam this paper in and out to relieve tension (if you were frustrated like me, haha) and the dirt on the inside roller comes off on the tape and then the roller has traction again!!!!! It literally takes 20 seconds (unless you have a ton of frustration to get out!!!!!) FYI DO NOT put that sticky paper on the floor if you have nosy cats .... yep, mine stepped RIGHT ON IT before entry!! Thank you so much for saving the printer from the trash and me from angina!!!
It’s 2020 and this still works, had my crappy work one break and then my home printer had THE SAME EXACT ISSUE. Not only was HPs help video worthless, this video saved me from throwing my printers out a window. I used a lint roller sheet and it was perfect. Thank you so much for this!
Thanks for the tip!
I was actually able to reach my printer's rollers with a q tip and some alcohol.
I wiped them for a couple minutes, let the alcohol dry for about ten minutes, and it started printing just fine!
the alcohol will dry out the rubber on the rollers with time. condition with a" LITTLE" coconut oil and feed a few pages threw to make sure all the access oil is off the rollers
@@squirrel3244 silicon oil i think
@@squirrel3244 Denatured alcohol should be ok too, it's not supposed to dry out rubber
Truly a life saver. I had an emergency this morning to print my kids’ test papers. This post solved the problem. Many thanks!
Thanks man! I didn't try your method since double tape isn't available but it was urgent for me to clean the rollers. With your video, I suddenly got an idea. What I did was: I made the end of a blank paper a little bit wet with water and a bit of alcohol. Just some drops of water on my fingers then spread it on the end. I saw some dirt that the wet end of the paper managed to remove. Then I decided that I should still clean it more, so I put some alcohol on my fingers and slightly wet the ends of another paper. And more dirt removed.
The result: feeder roller became more smooth. I don't have to put only one paper one by one whenever I need to print many pages or copies. :)
Someone suggested pushing through a piece of cardboard, scary. I cleaned it with a qtip right now, got some oily mess and now it's working again. Thank you mate.
Update 2022 . Your tip is still working . Just fixed my Pixma paper feed . I am very grateful to you . Thanks again .
This totally work!!! Paper was stuck in my printer from the back and I was panicking and searching at the same time for a RUclips video that could help me...Then I found you :)
Works 100% fine.
Cleaning with double tape won't damage your printer.
what I did:
take a thin cardboard (cornflakes box) (cauz paper might tear and jam in printer)
apply double tape in the end only (horizontally)
let it in and out of the paper tray manually (keep printer off)
You can see the dirt in the tape.
repeat above step until the roller is clean.
and your printer is ready to rock and 'roll'.
thank you so much for the video.
This sound good too! 👻
Thank you 🙂
This worked for me as well, I didn't dare feed the printer automatically with double sided tape on paper and this manual method is totally safe! (The tape i had at hand is very sticky, meant for carpets)
It worked :D
Shakthi Vel
Thanks soooo much for this tip! Worked like a charm. I've been dealing with this problem for a while and I was ready to toss my printer and get a new one.
I used my ruler and tape the ruler with a normal tape because I didnt had a double sided tape and cleaned the roller, and it worked. MAY GOD BLESS YOU!
Great idea! Thank you so much! Really helps us to see super positive comments like yours. May God bless you! 🤗
Its work with ruler!!! Thankyou!!
Hi, sharleen Id , Can I know that you did this with printer off or on ?
I never write comments...never...but this saved my life. God bless.
wait how?
hey man, just wanted to thank you! i was just about to visit a printer technician tomorrow to have my printer fixed. but your double sided tape gave me an idea. i instead attached a regular tape to a piece of paper and made sure they wouldn't come off easily even if i hold on to the paper so it doesn't go in completely.
after a couple cycles doing this, it works now even with just a single paper. thank you man, really really thank you!
Great idea! Thanks for watching!
Posted 5 years ago and saved my life today!!! Thank you so much for this, I was devastated not being able to load paper and so much urgent printing to do. Thank you!
Glad it helped!
Amazing! Thank you! Used a bit of lint roller paper. Got stuck a little, but came out with a ruler. Great solution that none of the experts suggested.
Please tell me how you used the lint roller paper....its my last resort. I tried alcohol, scotch tape it fed one time. Then I was back to force feeding with my hand. Thanks in advance.
Thanks! Cleaning the rollers is the definitely the way to go. I used a metal ruler with double sided sellotape and with the printer turned off I pushed it back and forth under the rollers. With your other hand use a long flat headed screwdriver to hold down the mechanism which holds the rollers (basically like an aircraft undercarriage) to ensure you get a tight fit when you squeeze the ruler between the platform below and the rollers. Worked for me and no risk to printer.
Yeah, my problem is that my printer's roller has ink on it, which gets in the paper before the actual printing... I'll try your method as it may work in my case!
thank you for this!!! i just did mine. metal ruler with tape. printing smoothly now!
This method works like a charm. Thanks! Of cause thanks to @ION How to who gave us the inspiration.
This video gave me ideas so I appreciate it. I ended up using a pencil, taped a q-tip to it, wrapped tape around the end of the q-tip and ran it across the rollers a few times and that worked for mine!
Thank you so much for this video, I was so focused on trying to reset it and get rid of the error rather than trying to solve the issue at hand. I almost destroyed this printer out of frustration, but this video saved me so much time and gave me such relief. I tried putting the cardboard in and then printing it out and once I did that the cardboard came through and with it included a piece of a sticky note that was jamming it! And afterwards it printed smoothly and perfectly. I cannot express enough gratitude for this video! I have a Canon Inkjet MG2522.
About to buy replacement printer found your video ordered Amazon Prime- 24 hour delivery -double side tape 2inch-cut A4 size small box cardboard sheet stuck length of tape sticky side up on the leading edge-to the edge-then with printer off pushed the cleaning board in and out a few times felt like an inch or so,-easy in tougher out then turned printer on with maybe 30 sheets or so in the loader and Bingo no issue the first sheet went straight in! Job done thanks to you,much appreciated well done! Mike
Thank you so much for the tip ! Instead of using double-sided tape, I used a sheet from a lint roller. Stuck it to the top of an envelope and pushed it under the rollers a few times. And then it just started working again.
Thank you so much for this video! We were about to give up and buy another printer! My husband did exactly as you said, with double sided tape, and it worked like a charm!!! Amazing!
Wow It worked for me thank you so much 😊 . My printer was troubling me for many days finally i searched on RUclips your printer looked similar to my printer so I watched your video 1st . No wasting of time watching other videos😄
The method really works! I used regular one-sided tape, taped down using margins on the sides. I had to pass the paper a few times before it started to work (so probably regular tape is not sticky enough), but after that it correctly fed paper like before.
great to see those close-up images of the rollers. thank you!
Thank you so much! I didn't have any double sided tape so did as someone in the comments suggested and used a sheet from my lint roller. I stuck it on to a piece of paper with sticky tape and fed it through the printer just once and it's now working great. Amazing how much dust and fluff came out on the sticky paper!
your solution sounds great, I'm gonna try fix my printer with a sheet from my lint roller as you suggest, I'm sure it'll work properly, thanks a lot
Wow thanks so much!! You saved us hundreds of dollars with a simple peice of tape. Thanks to you we don’t have to buy a new printer
Thank you! Tired of buying printers every time they don’t work right! We appreciate you!
Just tried the double back tape method & it worked great. I lined up 3/4" strips about 4' long to align with the rollers & ran it through the printer numerous times. After that, I lightly wet the strips and paper along the roller path to help remove remaining dust followed by new, dry paper to remove remaining water, it worked great...printer takes paper perfectly now, thanks for your great suggestion.
THANK YOU, Liked and Subscribed, thank you, I used some duck taped taped to a ruler upside down and it worked!!! Got the ruler under the rollers and it got the dirt off.
I have a cannon pixma e510, been frustrated for weeks thinking we'd have to replace it. now works like brand new. THANK YOU SO MUCH!!!!!!
Another printer saved! 👻
I love how all of the comments here are as useful as the video. Thank you for ypur tips! I'm having the same issue on my own printer. Hope this video and/or one of the comments here will help me fix my printer 🤞
I used a piece of lint roller that I use to collect pet hair. Some rollers have removable sticky layers whichs are less strong than double sided bands. Staple the sticky paper on a sheet and get a hold of it to prevent it to be taken into the printer. It worked for me.
Usei uma régua, durex, um cotonete e álcool.
Preguei o cotonete na régua com durex e molhei a cabeça do cotonete com álcool. Depois, enfiei a régua pela parte da frente da impressora, até aqueles rolinhos que puxam o papel pra dentro, e consegui limpar a poeira que estava acumulada lá. Depois disso, funcionou perfeitamente :) Thanks for video!
Thanks for the video. I happened to find a "Paint mixing stick" and "Painter's tape" in my garage. I taped a sticky side up tape at then end of the stick. Then used it to clean the wheels with other stick to hold and push down the wheel unit. It works like a charm.
Fantastic! Wife was getting so annoyed and kept bugging me for a new printer. This worked 1st time and now we are living happily ever after!
Great! Enjoy it! 😬
you can make the double sided tape less sticky by repeatedly pressing some material like denim (jeans) on it, or some cloth that doesn't leave bits of fluff.
Thanks. I have a similar printer to you, and your video helped me work out another method. I used some narrow double-side sticky tape on my finger to dap onto the pad at the bottom of the paper tray and the rollers above it. I did this by looking into the printer with the paper tray out as far as it goes for the pad on the paper tray, and by lifting one edge of the printer while the paper tray is out to access the rollers from the underside.
WORKS 100% Thank you very much,mate. It really works just fine. The printer does not have any issue malfunctioning or something, you just need to be a little careful during the process of inporting the double tape-paper. Thank you again. P.S. Canon Pixma MG3150
Nice 👻
Your tip still works. I thought my printer was possessed. Nope! It just needed to be cleaned. Thank you.
Brilliant ! A simple fix just as the printer was about to go out of the window !!
Enjoy it! 👻
Thanks! So, I read the other comments and had a think. Was worried about the doubles sided tape and paper getting stuck. So here's my upgrade on your initial great idea.
1. Got a large plastic ruler that was wide enough for to get under both wheels.
2. Double side taped on a strip of cotton (mine from a rag that was daughters old school sports shirt, mix of cotton and acrylic I guess? It has a rough weave) to end of ruler.
3. Soaked cloth in isopranol Alcohol, placed it under the wheels.
4. 'Printed' a blank sheet multiple times, pressing the green button (lower left) each time printer complained there was no paper.
6. Did this about 6 + times ... and lo and behold ! the next sheet of paper I printed worked.
NB - the bonus of using the Isopropanol was the double sided tape came off my ruler easily - but it stayed strong enough to not have the wheels pull the fabric off.
Hope this adds to this excellent, 'right to repair' video. Too many printers get thrown out that can be easily fixed !!
Wow thank you for the upgrade!
Small problem with alcohol on rubber but it would be wiped off the rubber rolls after printing just a few pages so it's fine! :)
@@IONHowTo Fair point about the alcohol, I did think about it but never had an issue with isopropanol, it evaporates so quickly. All the best!
Thank you Sir, I saw your video and it fixed my problem nicely. I was lucky to be able to access the rollers so I could feed the paper with sticky tape through manually with my fingers while the printer was powered off. It's a very clever simple solution that many people would not think of.
Holy crap, this worked! I just used regular double-sided tape on regular 8 1/2x11 paper. Thank you so much--one less printer for the landfill!
Really excited about your comment! Makes me very happy! :)
It's amazing how easy this problem translates to buying a new printer.
Thanks for saving your printer!
You’re a superstar! Thank you! Have been hand feeding paper for a while now....Didn’t have double-sided tape so just taped down 3 strips of regular scotch tape sticky side up and used qtips with alcohol on rollers...(must wait for it to dry!)..working beautifully!
I was about to buy a new printer under absolute frustralition. Your video allowed me to go a step further. Unplug the printer, turn it upside down, my printer had 4 philips head screws holding platic guides, remove 2 guides for the paper tray, removed them, removed the paper tray then peeled the rubbers off the pickup rollers then washed them with brush in dish washing liquid and water, dried with cloth (not tissues, they have oils), reinstalled on the rollers (already could feel the rubbers were more grippy) then reassembled the tray and guides.. Re plugged the printer and whoa, the printer was throwing the paper in.
Many thanks for the tip - I was just about to follow your method when I thought of using a vacuum cleaner to clear dust - and this worked!
Dragos you are a hero, this worked perfectly, Cannon should hire you.
Thank you! :) I don't think they like these videos.
I wouldn't recommend to buy a Canon Inkjet for home use.
Make your next printer a laser, HP/Samsung/Brother and it's all good.
Thanks, this helped me, too! Before this video i did not even imagine to check if the rollers are rolling. Once i figured they are, i took a 30 cm ruler and stuck some wide tape around it, sticky side out, and cleaned the rollers with that, further i wrapped that same ruler in an old tshirt that i moistened up and again cleaned the rollers. Seems to be working at least for now, and so happy i dont have to immediately cash out on a new one.
Nice! Enjoy it! :)
Wow thanks bro. I followed your double sided tape method, but paste the tape on a thicker piece of paper. Works wonderfully. My printer is working fine now! Thanks again bro!
I like your video because it shows the feed rollers spinning and not picking up the paper. I have an MX472 which is very similar in design. I cleaned the front feed rollers using a cotton swab, alcohol, tape, and a stick. I taped the swab to the stick because I couldn't get to the feed rollers any other way than through the paper feed slot and I couldn't reach them without the stick. I vacuumed out the printer as well. Once the rollers were cleaned they picked up the paper.
Thank you! I bought a printer from a garage sale and was about to chalk it up for a loss until I did what was on the video. It worked. I didnt have double sided tape so I tape three pieces sticky side up vertically and attached them with tape horizontally at the top and bottom
Nice
Thanks for the tip. I was worried about getting the rollers stuck, so instead I squirted some isopropyl alcohol on the paper A4 sheet to wet it and then pushed it through but grabbed the top of the sheet so that the rollers just spun on the wet paper. This did the trick and now it picks up OK.
Yay this actually worked!! I tried another cleaning hack first with isopropyl alcohol on a wipe taped to a piece of card and that didn't work...so I repeated that with this method, double sided tape over a piece of cardboard, and it picked up some hair (I didn't run it through, I pushed it back and forward whilst it was trying to print a test page). It's just a central roller on a Pixma MG4250, I was so skeptical - it works! It's even picking up my thick cardstock by itself, thank you!
Using this method with less aggressive tape works great. Fed the paper with tape twice thru the printer and have not had feeding issues since then, but maybe some time in the distant future I might need to go thru this process again.
That sounds great! A diy transport cleaning sheet. If the glue is not aggressive you can use it as many times as you need! 👻
HELP SAVE this CHANNEL and SUBSCRIBE NOW.
Dragos Ion RO
We need more than 1000 SUBSCRIBERS for this channel to SURVIVE!
If already subscribed, please tell a friend to subcribe!
Please SUBSCRIBE NOW!!!
I had a paper jam, got the paper out, but now on forms, the lines don't print straight and I have tried doing all the head adjustment and roller cleaning as described in the printer maintenance. Do you have any videos to help figure out how to fix that? I have a Canon MG 3122
No videos but you could try to also remove the cartridges and reinstall them and then do the print head alignment. If still no luck, something is very wrong with it.
Good idea. Thank you very much for this useful and do-able tip. I have the same printer & same problem. I tried to do it with two pieces of double sided tape applied at the end of card paper parallel to the paper edge (unlike your which was along the track of rollers) because I was scared of paper get jammed inside. I did it manually with printer off & then felt a bit confident to run the paper through the printer, switching it ON. To my utter shock, paper went inside smoothly but completely rolled over on one of the rollers bars,close to the outer tray due to the scotch tape adhesion. I did not take the risk of dismantelling the printer to reach that roller bar,so what I did was to cut the paper several times with a sharp cutter (risking the rubber of roller bar) & taking out piece by piece with a long tweezer. I removed the cartridges though. It took me almost one hour to take out the shreds of paper stuck in there. Then I cleaned the roller bar with alcohal. Finally the printer was OK & it worked perfectly taking in the papers smoothly. My advice: Do it manually, while printer is OFF.
Man that worked incredibly easy. I was about to throw my printer away and order another one. Thanks.
Great little video. Very helpful person. I never had a paper jam that I couldn't see from outside and never saw the thingie in back that exposes the rollers. Thanks very much. *****
Thanks man, did the same thing with my Epson Ecotank L3151, and worked like a charm. Keep in mind that Epson in its Ultra Glossy papers includes a special paper with glue to clean the pickup roller. I had some of those that do the job, but i was run out of them.
It really works! I used a very thin and soft ( i mean not too much sticky) double sided tape and printed a blank page several times. even I heard not any strange sound when printing. It just normally printed the taped page and is correctly working after then. Thank you!!
Thanks, man! it really worked I tied a 10 cm ruler with a spoon and at the end with cotton with some Perfume onto it. worked as if it were new.
Wow that's pretty nice! Perfume should work well.
Alcohol makes rubber dry so don't use too much.
If you can find alcohol-free wipes that's even better!
That's a pretty cool way to print some love letters. 😁
Thanks for saving my life its already 12am ! 2020 and it's really working!
Thank you! As you say, sounded like I was nearly breaking the printer and paper got jammed but I managed to get it out and not printer working fine.
works for my E560 !!!
thank you so much sir !!
but i don't think i will ever get another Canon printer in future
Multumesc! A mers si la mine (MG3150)
Nu am avut banda duble adeziva, asa ca am folosit 3 banzi adezive din hartie , puse (vertical) pe lungimea unei coli A4. Pe mijloc am pus banda cu adezivul in sus si pe laterare am prins-o cu cate o banda.
Great video. I just had to clean the rollers (easy access on my Canon MG5750 just by turning it over and pulling out the paper tray) and instant success. Thanks for pointing me in the right direction
This fix the most front feed printer problem. it seems stuck but when the roller cleared from dust it will feed the paper. i have to do the tape twice to make the roller feed papers smoothly. thanks for the video!
Thank s for this video , I was about to throw away my printer ,but I gave it a try , using a tape and found out a coin stuck on the tape ,when removed it got back to normal work . thumbs up!
Thanks it helped me... but i did little different, I cleaned the rollers using a earbud, and it worked! Thanks bro !
Just tried this method with about 3 inches of double sided tape and now my printer is ok! THANKS ALOT!
Hi. Why my pickup roller is not spinning at all after I replaced with the new one?
Thanks! That worked for my mx537. One tip is that you can open the back of the tray to prevent the second rolls from pulling the paper up.
I had already tried cleaning the feeders on the paper side, then I saw him trying to force the paper through and tried that. When I did a piece of moss popped out from deep inside the feeding mechanism o.0
Solved my problem in less than 5 mins and I didn't even have to watch the whole video ^^
In general, you should watch howto videos without skipping so you don't miss any important information.
Great way to get it fixed! Enjoy it!
EXCELLENT video! probably the best instruction video with printers of any kind that I have seen. enormously useful. Thanks you.
Thank you so much!! You saved my life! Before this Im waiting one by one paper to feed. After watch this video, it's work! I'm using sticker paper to clean the roller
hi how did this go and how did you do it? I'm having the same problems
I have a pixma mx475. For double sided tape i got post-it notes turned it upside down, sticky side up and taped it to an A4 sheet. Sticky enough for this task. While printer was off, pushed it in and out of the roller. Also the pad the rollers sit on gave that a clean too. Thanks for the video great help.
Nice trick with the post-it notes. That glue is perfect for this
Great video, just like to add a tip, check for obstruction say for example a pen lid🤣 found a stray one in mine causing havoc couldn’t see until I pulled it apart a bit. But might have come out easily if I had turned it upside down. All good now👍
Great tip!
Question! At 4:15 in the movie, when it’s zoomed in, a white part with a spring retracts into the roller. In my printer it doesn’t. It stays where it is and blocks the paper from going further. Any idea about the cause? Thanks for any help! I’m running out of options...
Try to use one sheet of paper and push it in slightly to help it go in.
Is that working?
Not all printers are the same but the roller should spin and try to take paper.
@@IONHowTo Thanks for the help! In the end, after unscrewing a part on the backside of the printer, I managed to have that white part stay in its retraced position. It may not be able serve its original purpose anymore, whatever it was, but the printer works!
Ended up taping some alcohol wipes to a ruler and sticking that in under the rollers while the printer was doing its cleaning routine. Once the rollers dried out, they started to pick up paper like new. Thanks!
You are genius man...it´s works!...But i did different, i put some paper (sticker letter paper) and put litle talcum powder to reduce the glue and put off the mashine and then i introduce the paper one and other time, maybe 4 times, for the wheels tuch well the paper and fix the problem! Thank you very much!
I wanted to almost throw my printer out of the window until I saw this video.
It worked for me.
The printer occasionally clicks a bit hard but now he takes the paper.
Thanks for sharing.
Great! Another printer saved 👻
I looked online and transport cleaning sheets are just very expensive. :(
Maybe will try this trick later when I got back from work. Thanks!
EDIT: dude your trick worked! it fixed the feeder so now my printer doesn't have problem pulling the paper :D thank you very much!!
EDIT2: i actually did the trick 2-3 times (with double-sided tape) to "force" the dust out of the feeder, now i'm a happy man :D
+opsddos Enjoy it :) yeah the original cleaning sheets are for speed ceanup in professional scanners or printers. Try to do it only when its really needed. Cheers :)
HELP SAVE this CHANNEL and SUBSCRIBE NOW.
Dragos Ion RO
We need more than 1000 SUBSCRIBERS for this channel to SURVIVE!
If already subscribed, please tell a friend to subcribe!
Please SUBSCRIBE NOW!
HELP SAVE this CHANNEL and SUBSCRIBE NOW.
Dragos Ion RO
We need more than 1000 SUBSCRIBERS for this channel to SURVIVE!
If already subscribed, please tell a friend to subcribe!
Please SUBSCRIBE NOW!
What is that white lever with the spring attached at 4:15. Rarely snaps back in my printer causing the paper to jam
I panicked when my printer wouldn't work and you did the trick. Omg thank you so much.
Thank you very much!
I tried a variation of the dubble sided tape: I glued a sheet of sticky notes upside down on a normal paper. The glue on the sticky notes did the job after a few repetitions.
Nice work!
Hi, I would like some advice regarding my printer if possible. I have a problem with my Canon mp287. Everytime I print, I get a slanted paper print result. I observed the feeding of the paper and saw that the left side of the paper goes in earlier than the right one. I wonder if you have any advice on how to fix this? Thank you!
Paper sits straight in the paper feed tray?
@@IONHowTo yes,it's straight but it literally gets slanted while printing
@@SayomiKamikura try to see if there's anything stuck on the paper transport rollers. You could try to look inside while it takes the paper. Could give you an idea about wheres the problem.
Ok tried it with the instructions. Tape got wrap around the rollers and I thought that's that then. So took pliers to unwrap the tape from the rollers and thought it's not going to work. Guess what, IT DID!! great tip and thanks. Like brand new
OMGoodness...... this technique just pushed out a piece of cardboard half the size of my hand. It was definetly not the uncoloured piece I pushed in as shown and got my TS3160 printing..... how the heck did the coloured carboard get into my printer..no idea ... All good now .. thankyou :)
Paper Feed Issue resolved: Canon MX 472 Should work well for other similar printers.
This RUclips video made me take the risk below. I was hoping it would work or throw out printer. Previously used Rubber Rejuvenator, alcohol, water. No luck. This worked. I had to junk 2 printers that I got for free before I did this.
My Steps:
Took basic file folder and cut to 8.5* 11 similar to basic standard printer paper.
Took Product: Touch ‘n Stick Spray Construction Adhesive Professional All Purpose Formula that I had in my shop for many years but can still buy doing an Internet search.
Sprayed about ¼ from of the top of the cut file folder.
Waved in air for about 5 seconds.
Pushed the top of sprayed cut file folder into input tray so that it would move the pick-up roller back and forth about 10 times smoothly and fairly quickly. Do not let the folder just sit touching the pickup roller or bottom of area pickup roller sits, keep on moving back and forth and then pull the cut folder out and away from the printer and into the trash.
Walked away for ½ hr.
Took my paper feed just fine. After a week still working. Feeding paper and printing.
This is my first post to RUclips because I share everyone’s pain and expense.
Thanks a lot for your precious help ! I used the double site tape carefuly and it worked very well 👍 Chris from France 🇫🇷
I had a different model, but your video helped me find the catch in the back panel.
Just used a flat ruller, on which I fixed with an elastic on one end, a computer wipe.
I put then some hydroalcoholic gel (for hands cleaning) on the wipe, to have it more wet.
Then I placed the wipe juste below the 2 transport wheels, and using the ruller, I forced the wheels upwards.
Then I start a print (copy), the transport wheels turn a bit then stop with the "no paper" sound.
I click "Ok" on printer, and then several times again, to force the little transport wheels to turn on the wipe, with ruller still in place and pushing the wipe upwards on the wheels.
After 5 or 6 times, I felt the little wheels were drawing more onto the wipe and ruller, so I stopped and waited 10 minutes to dry completly.
Then I tried with paper sheets, and the transport wheels were working perfectly as new :) !
Thanks for the idea of doing that, I was about to brick that 8 years MX535, but now it is working yet as new :D
Great idea! Thanks for watching!
來發個中文留言
這篇真的太強了！
成功救了我的canon
已經保內送修過
結果半年後又吃不到紙
他們工程師還說不可能一定是我的錯？
我剛剛ㄧ試就好了
太感動了
A piece of thin brass sheet with a clothes lint roller sheet Scotch-taped over the end worked for me on an Epson ESP-5250. Thanks for the tip.
EASY METHOD... Few sheets of paper, spray the end with Isopropyl Alcohol, the run roller cleaner (hold stop for 7 flashes). As rollers go, help paper in a bit if need be, but then hold it in place so rollers spin over the alcohol. Do it a couple of times if needs be. Easy, no mess and the cogs don't go mad clicking like crazy.
정말 감사합니다. 양면 테이프가 없어서 a4 한면 코팅지 필름을 사용햇습니다. 윗부분 5cm만을 벗겨내고 끈적한 부분을 롤러에 닿게 해 밀어넣고 앞뒤로 50번 정도 넣었다 뺏다 하는 식으로 수십번하니 이물질과 먼지들이 코팅지 접착면에 많이 묻어나왔습니다. 그리고 프린트 출력 테스트를 하자 3장 다 잘나오게 되었습니다. 덕분에 수리비가 들지 않았습니다. 당신에게 감사합니다.
How to connect this type of Canon GM1350 printer to my PC
Thank you for the brilliant and innovative solution. I used Scotch brand double sided tape and made the pieces about three inches long. It was just strong enough adhesive.
Don't forget to open the back of the printer when you run the tape through. Worked perfectly! Subscribed already!
Thank you for the comment! 👻 Great tip about opening the back! That makes it a lot more easy. 😁
Exactly, with the back open, the risk of jamming or damage is minimal.
Instead of double sided tape you can use mini cleaning towels with alcohol, to clean the rubber rolllers.